Page 1
BPSE240V47A
User’s Manual
K01-C000048-00
IMPORTANT SAFETY INSTRUCTIONS
This manual contains important instructions. Please read and follow all instructions carefully
during installation and operation of the unit. Read this manual thoroughly before attempting t o
unpack, install, or operate the Battery modules.
CAUTION! The UPS unit must be connected to a grounded AC power outlet with fuse or circuit
breaker protection. The Battery modules grounded are through the UPS.
CAUTION! The battery can power hazardous components inside the unit, even when the AC
input power is disconnected.
CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity
controlled indoor area, free of conductive contaminants. (Please see specifications for
acceptable temperature and humidity range).
CAUTION! (No User Serviceable Parts): Risk of electric shock, do not remove cover. No user
serviceable parts inside. Refer servicing to qualified service personnel.
1
CAUTION! (Non-Isolated Battery Supply): Risk of electric shock, battery circuit is not
isolated from AC power source; hazardous voltage may exist between battery terminals and
ground. Test before touching.
CAUTION! Wiring must be done by qualified personnel.
CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire, do not
use with or near aquariums. Condensation from the aquarium can come in contact with metal
electrical contacts and cause the machine to short out.
CAUTION! Do not dispose of batteries in fire as the battery may explode.
CAUTION! Do not open or mutilate the battery, released electrolyte is harmful to the skin and
eyes.
CAUTION! A battery can present a risk of electric shock and high short circuit current. The
following precaution should be observed when working on batteries
1. Remove watches, rings or other metal objects.
2. Use tools with insulated handles.
CAUTION! Make sure everything is turned off and disconnected completely before conducting
any maintenance, repairs or shipment.
CAUTION! Connect the Protection Earth (PE) safety conductor before any other cables are
connected.
DO NOT INSTALL THE UNIT WHERE IT WOULD BE EXPOSED TO DIRECT SUNLIGHT OR
NEAR A STRONG HEAT SOURCE!
SERVICING OF BATTERIES SHOULD BE PERFORMED OR SUPERVISED BY PERSONNEL
KNOWLEDGE OF BATTERIES AND THE REQUIRED PRECAUTIONS. KEEP
UNAUTHORIZED PERSONNEL AWAY FROM BATTERIES!
UNPACKING
UNPACKING
The box should contain the following:
Battery Module
User’s manual
Battery Cable
2
Page 2
SCHEMA
T
FRONT/R
E
① Output
Use this out
② On-bo
a
Replaceabl
e
③ Batter
y
Use this inp
u
IC
AR PANEL DE
S
Connector
put connector toco
n
rd Replaceable F
u
fuse is accessible
input Terminal Bl
u
t Terminal Block t
o
Battery String 1
BASIC OP
E
CRIPTION
nect the Battery m
o
se Cover
from the rear pane
ock
daisy chain thene
x
3
B attery String 2
Fuse
RATION
o
dule to the Power
l. It must be done b
tBattery module.
BATT.
O
BAT
T
BATT.
O
BAT
T
module.
y qualified personn
e
UTPUT
+
.INPU T UTPUT-
.INPU T
+
l.
CON
N
Step 1
Step
2
Step
3
ECTION #1 : P
O
:Connect the Batte
: Loosen thescrew
s
:Connect the Batte
WER MODUL
E
(
ry Cable to the Po
w
to remove the bat
t
ry Cable to the Bat
t
UPS) WITH ON
E
er module
and en
s
ery cable retention
ery module.
4
BATTERY MO
D
ure
the
polarity
i
s
bracket of the Batt
e
ULE
right.
ry module.
Page 3
Step 4: Rot
a
CONNEC
T
MODULE
S
Step 1:Loo
s
Step 2:Con
n
isright,then
r
te the battery cabl
e
ION #2 : POWE
R
en the screws to re
ect the Battery Ca
b
etighten the Block
retention bracket
a
MODUL
E
(
UPS
)
move the input Ter
m
le to the batteryin
p
Cover.
5
nd tighten thescre
w
WITH MULTIPL
E
inal Block Cover
o
ut Terminal Blocka
n
s to fix battery ca
b
BATTERY
f the 1st battery m
o
d ensurethe polari
t
le.
dule.
y
Step
3
batter
y
Step
4
Step
5
:Loosen the screw
s
module.
:Connect the 1stBa
t
:Rotate the battery
to remove the bat
t
tery moduleto the
2
1
st
cable retention bra
ery cable retention
nd
Battery module.
2st
cket and tighten th
e
6
bracket of the 2nd
screws to fix batte
r
y cable.
Page 4
Step 6:Connect the 1st Battery module to the Power module. (Refer to above steps of
connection #1)
TECHNICAL SPECIFICATIONS
Model BPSE240V47A
Battery
Sealed Maintenance Free
Lead Acid Battery
12V / 7Ah x20pcs x2sets
Rated Battery Voltage 240Vdc
Overload Protection Fuse
Physical
Maximum Dimensions
(HxWxD) (mm)
718x260x550
Weight (kg) 105
Environment
Operating Temperature 0C to 40C
Relative Humidity 0 to 90% (Non-condensing)
For more information, visit www.cpsww.com
All rights reserved. Reproduction without permission is prohibited.
7
Loading...