CyberPower 6K On-Line series, 8K On-Line series, 6KXL On-Line series, 10K On-Line series, 8KXL On-Line series User Manual

...

User’s Manual

CONTENT:

1. Safety and EMC Instructions .............................................................. 1

1.1 Installation........................................................................................ 1

1.2 Operation ........................................................................................ 2

1.3 Maintenance, Servicing and Faults ................................................. 2

1.4 Transport ......................................................................................... 3

1.5 Storage ...................................................................................... ...... 3

1.6 Standards ........................................................................................ 4

2. Description of Commonly Used Symbols ......................................... 5

3. Introduction .......................................................................................... 6

3.1 Feature ............................................................................................ 6

3.2 Electrical Specifications................................................................... 7

3.3 Operating Environment ................................................................... 8

3.4 Typical Backup Time (Typical Values at 25°C In Minutes) .............. 9

3.5 Dimensions and Weights........................................................ ......... 9

4. Installation .......................................................................................... 11

4.1 Moving to The Installation Site ...................................................... 11

4.2 Unpacking and Inspection ............................................................. 11

4.3 Input and Output Power Wires and Protective Earth Ground

Installation............................................................................................ 12

4.4 Operating Procedure for Connecting With The External Battery .. 16

4.5 EPO Connection............................................................................ 17

5. Operation........................................................................... .................. 18

5.1 Display Panel................................................................................. 18

5.2 Turning On and Turning Off UPS .................................................. 21

5.3 LCD Operation............................................................................... 22

6. Special Function................................................................................. 28

6.1 ECO Function ................................................................................... 28

6.2 Converter Function ........................................................................ 29

6.3 Parallel Function............................................................................ 29

7. Trouble Shooting................................................................................ 35

7.1 Trouble Shooting According to Warning Indication ....................... 35

7.2 Trouble Shooting According To Fault Indication ............................ 37

7.3 Trouble Shooting In Else Cases .................................................... 38

8. Battery Maintenance .......................................................................... 39

9. Communication Port .......................................................................... 40

9.1 USB Interface ................................................................................ 40

9.2 Dry contact Interface(optional)....................................................... 40

9.3 RS-232 Interface ……….............................................................. 40

9.4 Intelligent slot................................................................................. 40

1. Safety and EMC Instructions

Please read carefully the following user manual and the safety instructions before installing the unit or using the unit!

1.1 Installation

This is permanently connected equipment, and it must be installed by qualified maintenance personnel.

Condensation may occur if the UPS is moved directly from a cold to a warm environment. The UPS must be absolutely dry

before being installed. Please allow an acclimatization time of at

least two hours.

Do not install the UPS near water or in damp environment.

Do not install the UPS where it would be exposed to direct

sunlight or near heat.

Do not connect appliances or items of equipment which would

overload the UPS (e.g. laser printers, etc.) to the UPS output.

Place cables in such a way that no one can step on or trip over

them.

Connect UPS with the earth reliably before connecting to the

building wiring terminal, and external battery source must also

be earthed.

An integral single emergency switching device which prevents

further supply to the load by the UPS in any mode of operation

should be provided in the building wiring installation.

An appropriate disconnect device as short-circuit backup

protection should be provided in the building wiring installation.

The equipment is powered by two sources: the mains source,

the internal battery or the external battery source.

With the installation of the equipment, the sum of the leakage current of the UPS and the connected load does not exceed 5%

of rated value of input current.

Do not block ventilation openings in the UPS’s housing. Ensure

allow at least 50cm of space on front and rear of the UPS.

1.2 Operation

Do not disconnect the mains cable on the UPS or the building wiring terminals during operation since this would remove the

protective earth from the UPS and all connected loads.

The UPS output terminal block may still be electrically lived

even if the UPS is not connected to the building wiring terminal,

for there is internal current source (batteries).

In order to fully disconnect the UPS, first turn the input breaker

in the “OFF” position, then disconnect the mains lead.

Indiscriminate operation of switches may cause output loss or

damage to equipment. Refer to instruction before conducting

any control.

While the UPSs work as a parallel system, the external parallel

cable should be reinforced insulation.

Ensure that no liquid or other foreign objects can enter the UPS.

1.3 Maintenance, Servicing and Faults

Do not remove the enclosure since the UPS operates with hazardous voltages. It is to be serviced only by qualified

maintenance personnel.

Caution - risk of electric shock. Even after the unit is

disconnected from the mains power supply (building wiring

terminal), components inside the UPS are still connected to the

battery which are potentially dangerous.

Before carrying out any kind of service and/or maintenance, isolate UPS and disconnect the batteries. Verify that no current

is present and no hazardous voltage exists in the capacitor or

BUS capacitor.

Batteries must be replaced only by qualified personnel.

Batteries have a high short-circuit current and pose a risk of

shock. Take all precautionary measures specified below and

any other necessary measures when working with batteries:

remove all jewellery, wristwatches, rings and other metal

objects

use only tools with insulated grips and handles.

When changing batteries, replace with the same quantity and

the same type of batteries.

Do not attempt to dispose of batteries by burning them. It could

cause explosion.

The UPS may be connected to external battery module (EBM).

Proper disposal of batteries is required. Refer to your local

codes for disposal requirements.

Do not open or destroy batteries. Effluent electrolyte can cause

injury to the skin and eyes. It may be toxic.

Replace the fuse only by a fuse of the same type and of the

same spec in order to avoid fire hazards.

1.4 Transport

Please transport the UPS only in the original packaging to protect against shock and impact.

1.5 Storage

The UPS must be stockpiled in the room where it is ventilated and dry.

* Safety

IEC/EN 62040-1

* EMI

Conducted Emission..........................:IEC/EN 62040-2

Category C3

Radiated Emission.............................:IEC/EN 62040-2

Category C3

* EMS

Level 3

Level 4

CS……………………………………...:IEC/EN 61000-4-6

Level 3

MS……………………………………..: IEC/EN 61000-4-8

Level 3

Voltage Dips……………………….....: IEC/EN 61000-4-11

Low Frequency Signals.....................:IEC/EN 61000-2-2

Warning: This is a product for commercial and industrial application in the

needed to prevent disturbances.

1.6 Standards

2. Description of Commonly Used Symbols

Some or all of the following symbols may be used in this manual. It is advisable to familiarize yourself with them and understand their

meaning:

Symbol and Explanation

Symbol

Explanation

Symbol

Explanation

Alert you to pay

special

attention

Caution of high

voltage

Alternating

current

source(AC)

Direct current

source(DC)

Turn on or turn

off the UPS

Protective

ground

Recycle

Do not dispose

with ordinary

trash

Model No.

Type

Model No.

Type

Standard

6KXL

Exended

backup time

8KXL

10K

10KXL

3. Introduction

This On-Line series is an uninterruptible power supply incorporating

double-converter technology. It provides perfect protection specifically

for computer equipments, communication servers, and data centers.

The double-converter principle eliminates all mains power

disturbances. A rectifier converts the alternating current from the mains

power to direct current. On the basis of this DC voltage, the inverter

generates an AC sinusoidal voltage, which constantly supplies the

loads. In the event of power failure, the maintenance-free batteries

power the inverter.

This manual covers the UPS listed as follows. Please confirm whether

it is the model you intend to purchase by performing a visual inspection

of the Model No. on the rear panel of the UPS.

“XL” Model: Extended backup time

3.1 Feature

This series UPS is a new generation of UPS, which provides the outstanding reliability, and most cost-performance ratio in the industrial.

Following benefit the product has:

True online double-conversion technology with high power

density, frequency independence, and generator compatibility.

 Output power factor is 0.9, perfect output sine waveform,

suitable almost all critical equipment.

 High input power factor ≥0.99,overall high efficiency ≥ 0.92,

save power and wiring expense for user. Low input current

distortion, avoid power pollution.

INPUT

Model No.

6K(XL)

8K(XL)

10K(XL)

Phase

Single

Voltage

176~276VAC

Frequency

(45~55)/(54~66) Hz

Current(A)

31(36)

40(45.5)

50(55)

THDI

< 5% @ full load

Power Factor

0.99 @ full load

OUTPUT

Model No.

6K(XL)

8K(XL)

10K(XL)

Power rating

6kVA/5.4kW

8kVA/7.2kW

10kVA/9kW

Voltage

208*/220/230/240×(1±1%) VAC

Frequency

50/60× (1±0.05) Hz (Battery mode)

 Outstanding adaptability to the worst mains input condition.

Extra wide input voltage, frequency range and waveform, avoid

excessive dissipating limited battery energy.

 Internal charger could be up to 4Amps to decrease recharging

time of battery. Optional external large charging current charger

which is up to 12Amps could be supplied.

 N+X parallel redundancy to increase the reliability and flexibility.

Number of parallel operating UPS is up to 4.

 ECO mode with high efficiency ≥ 0.96, save power expense for

user.

 Start-able without battery.

3.2 Electrical specifications

Wave form

sine

Load type

PF 0.5~1, lagging

THDV

< 2% @ full linear load

<5% @ full nonlinear load

Overload

In Line mode**:

10 min 105~125% 1 min 125~150%

10 S >150%

100 mS >170%

In Battery mode:

2 min 105~125% 30 S 125~150%

100 mS >150%

Operating Temperature 0 C to 45 C

Operating humidity < 95%

Altitude < 1000m*

Storage temperature -15 C to 50 C

BATTERIES

Model No.

6K8K10K

Internal BAT

number and type

20×12V 28W

20×12V 34W

BAT pack

28A 37.4A 47A

*The load capacity would be derated to 90% automatically when the output

voltage is adjusted to 208VAC.

**The overload capacity would be derated automatically in Line mode while the

circumstance temperature is larger than 35 degree.

3.3 Operating Environment

*The load capacity should be derated 1% every 100m heightened on the basis of 1000m.

Model No.

Dimensions W×H×D

(mm)

Net Weight

(kg)

6K 260 x 708 x 550 70

6KXL 260 x 708 x 550 25

8K 260 x 708 x 550 86

8KXL 260 x 708 x 550 28

10K 260 x 708 x 550 86

10KXL 260 x 708 x 550 28

Model No. 100 % Load

10K 4

3.4 Typical Backup Time (Typical values at 25°C in minutes)

3.5 Dimensions and Weights

USB Port

RS 232

EPO Port

Dry contact (optional)

Intelligent Slot

Fan

Parallel Port

Maintenance Switch

Input Breaker

Terminal Block

6K(XL)

10K(XL)

Fig. 3-1 Back View of 6K(XL)/10K(XL)

*The back view of 8K(XL) models are same as 10K(XL) models.

+ 30 hidden pages

CyberPower 6K On-Line series, 8K On-Line series, 6KXL On-Line series, 10K On-Line series, 8KXL On-Line series User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual