CyberData VoIP Zone Controller Installation Quick Reference

Hole size for Anchor installation: 3/16" (0.1875")

Screws: #6 x 1-1/2" Screw

Product Specifications

Regulatory Compliance FCC Class A, UL 60950, CE

Power Requirement PoE or +48VDC

LAN Speed 10/100 Mbps

Protocol SiP compliant

Part Number 010881

Dimensions 6.11”L x 4.05”W x 1.15” H

Weight 1.2 lbs.

(2) #6 Mounting Anchors (2) #6 x 1 1/2" Screws

(1) Mounting Template (see the last page)

(1) Mounting Kit

(1) VoIP Zone Controller - 4-Port Audio Out

VoIP Zone Controller Mounting Template

Installation Quick Reference

VoIP Zone Controller:
4-Port Audio Out

Sip Compliant

The VoIP Zone Controller is a PoE-enabled, single SIP-endpoint enabling user defined paging zones through a line-out
connection to legacy analog amplifiers connected to existing legacy analog paging speakers. SIP compliant IP-PBX's can
now interface with existing legacy analog paging speaker installations.

Getting Started

● Be sure that you have received all the parts described in the Parts List section.

● Download the VoIP Zone Controller - 4-Port Audio Out Operations Guide at:

http://www.cyberdata.net/support/download.html or go to www.cyberdata.net—>Support—>
FAQs, Drivers, Utilities & Manuals—>FAQs, Product Drivers & Documentation

Parts List

Quick Reference 930108B © 2009 CyberData Corporation ALL RIGHTS RESERVED© 2009 CyberData Corporation ALL RIGHTS RESERVED 930108B Quick Reference

To restore the VoIP Zone Controller’s factory
default settings, press and hold the RTFM

turn back on, and then release the switch. All
VoIP Zone Controller settings are restored to the
factory defaults, and the unit reboots.

Green Link light indicates network connectivity

Orange Link light indicates 100Mbps baud rate

Yellow Link light indicates 10Mbps baud rate

Blinking yellow Act light indicates network
activity

Blinking blue Status light indicates the unit is
running

Green Paging light indicates the unit is paging

Front View with LEDs

Back View with RTFM Switch

Warranty

CyberData warrants its product against defects in material and workmanship for a
period of two years from the date of purchase. Should the product fail within the
warranty period, CyberData will repair or replace the product free of charge. This
warranty includes all parts and labor. Should the product fail out-of-warranty, a flat
rate repair charge of one half the purchase price will be assessed. Repair costs for
products that are in warranty, but damaged by improper modifications or abuse,
are charged at the out-of-warranty rate. Products returned to CyberData, both in
and out-of-warranty, are shipped to CyberData at the customer’s expense.
Charges for shipping repaired products to the customer are paid by CyberData.

For product service, contact the Returned Materials Authorization (RMA) depart­ment. A product will not be accepted for return without an approved RMA number.
Send the product, in its original package, to: CyberData Corporation, 2555 Garden
Road, Monterey, CA 93940, Attention: RMA “your RMA number”

Corporate Headquarters

CyberData Corporation
2555 Garden Road
Monterey, CA 93940, USA

Phone: [phone]
Fax: [phone]
www.CyberData.net

Sales: [phone] ext. 334

Support: 831-373-2601 ext. 333
Email: [e-mail]

RMA Dept: [phone] ext. 136
Email: [e-mail]

Typical Zone Controller Setup Using the VoIP Zone Controller

You have the option to use the mounting template
on the last page of this document to mark, and then
drill two 5/32” (0.1875”) holes for the mounting
anchors. Then, install the mounting anchors in the
holes, and position the VoIP Zone Controller
mounting holes over the anchors. Use the two #6
sheet metal screws to secure the VoIP Zone
Controller onto the mounting surface.

To set up the VoIP Zone Controller:

1. Connect it to your network. To use PoE, plug
one end of an 802.3af Ethernet cable into the
VoIP Zone Controller Ethernet port. Plug the
other end into your network. Or, use a
standard Ethernet cable, and a 48VDC power
supply as directed in Step 3.

2. When not using PoE, also connect the VoIP
Zone Controller to a 48VDC power supply.

3. If required, connect the earth grounding wire
to the chassis ground.

Step 3

Step 1

Step 2

Verifying Operations and Settings

Mounting (optional) and Setting Up the VoIP Zone Controller: 4-Port Audio Out

© 2009 CyberData Corporation ALL RIGHTS RESERVED 930108B Quick Reference Quick Reference 930108B © 2009 CyberData Corporation ALL RIGHTS RESERVED

Contacting CyberData