CyberData 011397, 011398, 011395, 011396 Operation Manual

Download

SIP Talk-Back Speaker

The IP Endpoint Company

Operations Guide

Part #011397*, RAL 9002, Gray White, Standard

Part #011398*, RAL 9003, Signal White, Optional

*Replaces #011180 and 011181



Document Part #931191I

for Firmware Version 11.6.9

CyberData Corporation

3 Justin Court

Monterey, CA 93940

(831) 373-2601

SIP Talk-Back Speaker Operations Guide 931191I

Technical Support  

The fastest way to get technical support for your VoIP product is to submit a VoIP Technical Support form at the following website:

http://support.cyberdata.net/



Phone: (831) 373-2601, Ext. 333 Email: support@cyberdata.net Fax: (831) 373-4193 Company and product information is at www.cyberdata.net.

Part # 011397 Part # 011398

This manual and related materials are the copyrighted property of CyberData Corporation. No part of this manual or related materials may be reproduced or transmitted, in any form or by any means (except for internal use by licensed customers), without prior express written permission of CyberData Corporation. This manual, and the products, software, firmware, and/or hardware described in this manual are the property of CyberData Corporation, provided under the terms of an agreement between CyberData Corporation and recipient of this manual, and their use is subject to that agreement and its terms.

DISCLAIMER: Except as expressly and specifically stated in a written agreement executed by CyberData Corporation, CyberData Corporation makes no representation or warranty, express or implied, including any warranty or merchantability or fitness for any purpose, with respect to this manual or the products, software, firmware, and/or hardware described herein, and CyberData Corporation assumes no liability for damages or claims resulting from any use of this manual or such products, software, firmware, and/or hardware. CyberData Corporation reserves the right to make changes, without notice, to this manual and to any such product, software, firmware, and/or hardware.

OPEN SOURCE STATEMENT: Certain software components included in CyberData products are subject to the GNU General Public License (GPL) and Lesser GNU General Public License (LGPL) “open source” or “free software” licenses. Some of this Open Source Software may be owned by third parties. Open Source Software is not subject to the terms and conditions of the CyberData COPYRIGHT NOTICE or software licenses. Your right to copy, modify, and distribute any Open Source Software is determined by the terms of the GPL, LGPL, or third party, according to who licenses that software.

Software or firmware developed by CyberData that is unrelated to Open Source Software is copyrighted by CyberData, subject to the terms of CyberData licenses, and may not be copied, modified, reverse-engineered, or otherwise altered without explicit written permission from CyberData Corporation.

TRADEMARK NOTICE: CyberData Corporation and the CyberData Corporation logos are trademarks of CyberData Corporation. Other product names, trademarks, and service marks may be the trademarks or registered trademarks of their respective owners.

The IP Endpoint Company

CyberData Corporation 931191I Operations Guide

Revision Information

Revision 931191I, which corresponds to firmware version 11.6.9, was released on September 22, 2017, and has the following changes:

• Updates Section 1.3, "Product Features"

• Updates Ta bl e 1-1, "Product Specifications"

Browsers Supported

The following browsers have been tested against firmware version 11.6.9:

• Internet Explorer (version: 10)

• Firefox (also called Mozilla Firefox) (version: 23.0.1)

• Chrome (version: 29.0.154.66 m)

• Safari (version: 5.1.7)

Operations Guide 931191I CyberData Corporation

Pictorial Alert Icons

GENERAL ALERT

Hazard Levels

Danger: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This is limited to the most extreme situations.

Warning: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

General Alert

This pictoral alert indicates a potentially hazardous situation. This alert will be followed by a hazard level heading and more specific information about the hazard.

Ground

This pictoral alert indicates the Earth grounding connection point.

Caution: Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. It may also alert users against unsafe practices.

Notice: Indicates a statement of company policy (that is, a safety policy or protection of property).

The safety guidelines for the equipment in this manual do not purport to address all the safety issues of the equipment. It is the responsibility of the user to establish appropriate safety, ergonomic, and health practices and determine the applicability of regulatory limitations prior to use. Potential safety hazards are identified in this manual through the use of words Danger, Warning, and Caution, the specific hazard type, and pictorial alert icons.

CyberData Corporation 931191I Operations Guide

Important Safety Instructions

GENERAL ALERT

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

13. Prior to installation, consult local building and electrical code requirements.

Warn in g

Electrical Hazard: This product should be installed by a licensed electrician according to all local electrical and building codes.

Warn in g

Electrical Hazard: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.

Warn in g

The PoE connector is intended for intra-building connections only and does not route to the outside plant.

CyberData Corporation 931191I Operations Guide

Abbreviations and Terms

Abbreviation or Term Definition

A-law A standard companding algorithm, used in European digital

communications systems to optimize, i.e., modify, the dynamic range of an analog signal for digitizing.

AVP Audio Video Profile

Cat 5 TIA/EIA-568-B Category 5

DHCP Dynamic Host Configuration Protocol

LAN Local Area Network

LED Light Emitting Diode

Mbps Megabits per Second.

NTP Network Time Protocol

PBX Private Branch Exchange

PoE Power over Ethernet (as per IEEE 802.3af standard)

RTFM Reset Test Function Management

SIP Session Initiated Protocol

u-law A companding algorithm, primarily used in the digital telecommunication

UC Unified Communications

VoIP Voice over Internet Protocol

CyberData Corporation 931191I Operations Guide

Chapter 1 Product Overview 1

1.1 How to Identify This Product .....................................................................................................1

1.2 Installation ................................................................................................................................2

1.3 Product Features ......................................................................................................................3

1.4 Supported Protocols .................................................................................................................4

1.5 Supported SIP Servers .............................................................................................................4

1.6 Product Specifications ..............................................................................................................5

1.7 Optional Connections (J9 and J10) ..........................................................................................6

1.8 Compliance ..............................................................................................................................6

1.8.1 CE Testing ......................................................................................................................6

1.8.2 FCC Statement ..............................................................................................................6

1.9 SIP Talk-Back Speaker Modes .................................................................................................7

1.9.1 Optional 011185 Remote Call Button (sold separately) .................................................7

1.9.2 Normal Mode ..................................................................................................................7

1.9.3 Monitor Mode ...............................................................................................................10

Chapter 2 Installing the SIP Talk-Back Speaker 12

2.1 Parts List ................................................................................................................................12

2.2 Device Configuration ..............................................................................................................13

2.2.1 Connect Power to the Speaker ....................................................................................14

2.2.2 Installation Options .......................................................................................................17

2.2.3 Confirm that the Speaker is Operational and Linked to the Network ..........................23

2.2.4 Confirm the IP Address and Test the Audio .................................................................24

2.2.5 Adjust the Volume ........................................................................................................25

2.2.6 How to Set the Factory Default Settings .......................................................................26

2.3.1 Factory Default Settings ...............................................................................................27

2.3.2 SIP Talk-Back Speaker Web Page Navigation .............................................................28

2.3.3 Using the Toggle Help Button .......................................................................................29

2.3.4 Log in to the Configuration Home Page .......................................................................31

2.3.5 Configure the Device ....................................................................................................35

2.3.6 Configure the Network Parameters .............................................................................45

2.3.7 Configure the SIP (Session Initiation Protocol) Parameters .........................................48

2.3.8 Configure the Multicast Parameters .............................................................................58

2.3.9 Configure the Sensor Configuration Parameters ..........................................................61

2.3.10 Configure the Audio Configuration Parameters ..........................................................65

2.3.11 Configure the Events Parameters ..............................................................................72

2.3.12 Configure the Autoprovisioning Parameters ...............................................................78

2.4.1 Downloading the Firmware ...........................................................................................90

2.4.2 Reboot the Device ........................................................................................................92

2.5.1 Command Interface Post Commands ..........................................................................93

Appendix A Mounting the Speaker 97

A.1 Mount the Speaker ................................................................................................................97

A.2 Dimensions ............................................................................................................................99

Appendix B Setting up a TFTP Server 100

B.1 Set up a TFTP Server ..........................................................................................................100

B.1.1 In a LINUX Environment ............................................................................................100

B.1.2 In a Windows Environment .......................................................................................100

Appendix C Troubleshooting/Technical Support 101

C.1 Frequently Asked Questions (FAQ) ......................................................................................101

C.2 Documentation .....................................................................................................................101

C.3 Contact Information ..............................................................................................................102

Operations Guide 931191I CyberData Corporation

C.4 Warranty and RMA Information ............................................................................................102

Index 103

Operations Guide 931191I CyberData Corporation

1 Product Overview

SIP Talk Back Speaker

011397A / 021515FI2

www.cyberdata.net

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:  (1) this device may not cause harmful interference, and (2) this device must accept any interference received,  including interference that may cause undesired operation.

CAN ICES-3 (A)/NMB-3(A)

00:20:F7:03:83:CA

397000001

Serial number begins with 393

11.6.9

Model number

1.1 How to Identify This Product

To identify the SIP Talk-Back Speaker, look for a model number label similar to the one shown  in Figure 1-1. The model number on the label should be one of the following:

• 011397, RAL 9002, Gray White, Standard Color

• 011398, RAL 9003, Signal White, Optional Color

Figure 1-1. Model Number Label

Operations Guide 931191I CyberData Corporation

1.2 Installation

Remote Call Button

802.3af/at Compliant Ethernet Switch

IP Phone IP PBX Server

SIP Talk-Back Speakers

(sold separately)

Figure 1-2 illustrates a typical configurations for the SIP Talk-Back Speaker.

Figure 1-2. Typical Installation

Product Overview

Installation

See the following sections for other installation options:

• Section 2.2.1.3, "Running the SIP Talk-Back Speaker with Auxiliary Power"

• Section 2.2.2.4, "SIP Talk-Back Speaker with an External Device"

• Section 2.2.2.5, "SIP Talk-Back Speaker with Auxiliary Speaker Connection"

• Section 2.2.2.6, "SIP Talk-Back Speaker with Line Out"

Operations Guide 931191I CyberData Corporation

1.3 Product Features

• Full-duplex (SIP) or half-duplex (push to talk)

• Page to Polycom phones

• Added stored messages with option to enable or disable playback

• Support for security code to prevent unwanted SIP calls

• Optional red/green/blue/white strobe kit connection available

• Autoprovisioning via HTTP, HTTPS, or TFTP

• HTTPS or HTTP web based configuration. HTTPS is enabled by default.

• 802.11q VLAN tagging

• Configurable sense input for use with fault detection or with optional lighted button kit

• Configurable event generation for device health and status monitoring

• Support for G.711 u-law, G.711 a-law, and G.722 codecs.

• Powered via PoE (802.3AF or 802.3AT) or 24V auxiliary power supply (not included)

• Enhanced interoperability for hosted environments

• IP (RFC 3261) compatible

• Night Ringer function

• Plays audio from Multicast

• Web-based configuration

• Paging prioritization and background music

• User upgradeable firmware via web interface or autoprovisioning

• External volume control

• Small footprint

• High efficiency speaker driver

• IGMP l SIP endpoint or Multicast group member

• Network-adjustable speaker volume

• Optional auxiliary speaker available to increase audio coverage - Part #011120/011121

• Optional clock kit available - Part #011153/011154

• Support for 10 multicast paging groups

• Support for multiple SIP servers for redundancy

• Support for Cisco SRST resiliency

• Relay for activating door locks, external amplifiers, etc.

• Line-level audio output for connecting to an external amplifier

Product Overview

Product Features

Operations Guide 931191I CyberData Corporation

1.4 Supported Protocols

The SIP Talk-Back Speaker supports:

•SIP

• Multicast

• HTTP Web-based configuration

Provides an intuitive user interface for easy system configuration and verification of speaker operations.

• DHCP Client

Dynamically assigns IP addresses in addition to the option to use static addressing.

• HTTP TCP Post auto-updating event notification in XML format

• TFTP Client

Facilitates hosting for the configuration file for Autoprovisioning.

• Audio Encodings

PCMU (G.711 mu-law)

PCMA (G.711 A-law)

Packet Time 20 ms

Product Overview

Supported Protocols

1.5 Supported SIP Servers

The following link contains information on how to configure the speaker for the supported SIP servers:

http://www.cyberdata.net/connecting-to-ip-pbx-servers/

Operations Guide 931191I CyberData Corporation

Product Overview

Product Specifications

1.6 Product Specifications

Table 1-1. Product Specifications

Category Specification

Audio output 802.3af - SPL 109.2 dB @ 1 meter

802.3at - SPL 111.9 dB @ 1 meter

Operating Range Temperature: -40

Humidity: 5-95%, non-condensing

Storage Temperature

Storage Altitude

Ethernet port baud rate 10/100 Mbps

Protocol SIP RFC 3261 Compatible

Power Input (J1) PoE 802.3af (as per IEEE 802.3af standard from a UL-listed, LPS-rated limited power source)

or Auxiliary Power Inputa (Terminal Block J10)

Total Power ~ 15W

Network Line loss ~ 2W

C to 70o C (-40o F to 158o F)

-40

Up to 15,000 ft. (4573 m)

802.3at

44-57 VDC (48 VDC nominal) at 350mA

24 VDC at 1A (from a UL-listed, LPS-rated power supply)

C to 55o C (-40o F to 131o F)

Total Pwr @ VoIP Speaker

Total available audio power

Idle PWR (losses/CPU) ~ 3W

Payload types G.711 µ-law, G.711 a-law, and G.722

Warranty 2 years limited

Dimensions 9 in. [228.6 mm] x 2.4 in. [60.96 mm]

Weight 2.8 lbs./shipping weight of 3.8 lbs.

Compliance CE; EMC Directive – Class A EN 55032 & EN 55024, LV Safety Directive – EN 60950-1, RoHS

Part number 011397*, RAL 9002, Gray White, Standard Color

~ 13W

~ 10W

(1.3 kg/shipping weight of 1.7 kg)

Compliant, FCC; Part 15 Class A, Industry Canada; ICES-3 Class A, IEEE 802.3 Compliant

011398*, RAL 9003, Signal White, Optional Color

*Replaces 011180 and 011181.

a.Auxiliary power input for use when PoE power is not available. 24 VDC @ 1A. Do not use auxiliary power input when speaker J1 is connected to a PoE power source.

Operations Guide 931191I CyberData Corporation

1.7 Optional Connections (J9 and J10)

AUX SPEAKER (-)

AUX SPEAKER (+)

GND

LINE OUT (-)

LINE OUT (+)

BUTTON LED (+)

RELAY NO

RELAY COM

AUX POWER (-)

AUX POWER (+)

(+24VDC @ 1A)

J10

*Auxiliary power input for use when PoE power is not available. +24 VDC @ 1A.

Relay contacts rated at  30 VDC @ 1A.

Auxiliary 8-Ohm speaker  connection (not to be used when the Clock is connected.

Audio line - level output to  external audio amplifier.  2v P-P into 10k Ohms.

*Do not use auxiliary power input when speaker J1 is connected to a PoE power source.

Function

FunctionJ10 Connections J9 Connections

BTN SENSE

BUTTON LED (-)

CLASS II WIRING

Figure 1-3. Optional Connections (J9 and J10)

Product Overview

Optional Connections (J9 and J10)

1.8 Compliance

1.8.1 CE Testing

1.8.2 FCC Statement

CE testing has been performed according to EN ISO/IEC 17050 for Emissions, Immunity, and Safety.

Note You can download the Declaration of Conformity document from the Downloads tab of the

product’s webpage.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Operations Guide 931191I CyberData Corporation

1.9 SIP Talk-Back Speaker Modes

IP Phone

SIP Talk-Back Speaker

SIP Talk-Back Speaker makes a call or dials a SIP extension.

Phone user dials the SIP Talk-Back Speaker.

Push the Call Button Note: See Section 1.9.1, "Optional 011185

Remote Call Button (sold separately)"

1.9.1 Optional 011185 Remote Call Button (sold separately)

Section 1.9, "SIP Talk-Back Speaker Modes" shows the optional 011185 Remote Call Button which

is sold separately. For more information about this product, go to the following webpage:

http://www.cyberdata.net/voip/011185/

1.9.2 Normal Mode

•In Normal Mode, a person can use the Remote Call Button and the SIP Talk-Back Speaker to call an IP phone or a phone user can call the SIP Talk-Back Speaker. See

Note Normal Mode requires the use of the Button Installed and Enable Push to Talk features

listed on the Device Configuration Page.

Product Overview

SIP Talk-Back Speaker Modes

Figure 1-4.

Figure 1-4. Normal Mode

• Push the Call Button to make a call or dial the SIP extension. See Figure 1-5.

Figure 1-5. Push the Call Button to Make a Call

Operations Guide 931191I CyberData Corporation

Product Overview

Push the Call Button Note: See Section 1.9.1,

"Optional 011185 Remote Call Button (sold separately)"

SIP Talk-Back Speaker Modes

Operations Guide 931191I CyberData Corporation

Product Overview

Hold down the Call Button while talking Note: See Section 1.9.1,

"Optional 011185 Remote Call Button (sold separately)"

Release the Call Button while listening Note: See Section 1.9.1,

"Optional 011185 Remote Call Button (sold sepa-

rately)"

SIP Talk-Back Speaker Modes

• To talk to someone on the other end, the person at the SIP Talk-Back Speaker, must hold down the Call Button while they are talking to the person on the other end. See

Figure 1-6.

Figure 1-6. Hold Down the Call Button While Talking

• To listen to someone talking on the other end, the person at the SIP Talk-Back Speaker must release the Call Button. See

Figure 1-7.

Figure 1-7. Release the Call Button While Listening

Operations Guide 931191I CyberData Corporation

1.9.3 Monitor Mode

IP Phone

Ta lk - B ac k

Speaker Sound, noise, or activity near the SIP Talk-Back

Dial the pre-programmed Monitor Extension

•In Monitor Mode, the person on the phone can listen to any activity that is occurring near the Push-to-Talk Speaker. See

• The Call Button is not used during Monitor Mode.

• Monitor Mode is controlled by the phone instead of the Push-to-Talk Speaker.

• To initiate the Monitor Mode, someone on a phone must dial the pre-programmed Monitor Extension. See

Figure 1-8.

Figure 1-8. Monitor Mode

Figure 1-9.

Product Overview

SIP Talk-Back Speaker Modes

Figure 1-9. Dial the Monitor Extension

Operations Guide 931191I CyberData Corporation

Product Overview

Talking and listening modes are controlled by the phone keypad

SIP Talk-Back Speaker Modes

•In Monitor Mode, the "talking mode" and the "listening mode" are controlled by one of the pre- programmed buttons on the phone keypad. Therefore, if someone is in the "listening mode," they must press a pre-programmed keypad button to enter the "talking mode." Conversely, if someone is in the "talking mode," they must press a pre-programmed keypad button to enter the "listening mode."

Figure 1-10. Talking and Listening Modes are Controlled by the Phone Keypad

Operations Guide 931191I CyberData Corporation

2 Installing the SIP Talk-Back Speaker

2.1 Parts List

Ta bl e 2-1 illustrates the parts for each speaker and includes kits for the drop ceiling and drywall

mounting.

Note The installation template for the SIP Talk-Back Speaker is locate

Reference Guide that is included in the packaging with each speaker.

Table 2-1. Parts

Quantity Part Name Illustration

1 SIP Talk-Back Speaker Assembly

1 Installation Quick Reference Guide

1 Speaker Mounting Accessory Kit

d on the Installation Quick

Operations Guide 931191I CyberData Corporation

2.2 Device Configuration

Set up and configure each speaker before you mount it.

CyberData delivers each speaker with the following factory default values:

Table 2-2. Factory Network Default Settings—Default of Network

Parameter Factory Default Setting

IP Addressing DHCP

IP Address

Web Access Username admin

Web Access Password admin

Subnet Mask

Default Gateway

a. Default if there is not a DHCP server present.

10.10.10.10

255.0.0.0

10.0.0.1

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

2.2.1 Connect Power to the Speaker

802.3af Compliant PoE Switch

Cat 5 Ethernet cable

SIP Talk-Back Speaker

Figure 2-1 through Figure 2-3 illustrates how to connect power to the SIP Talk-Back Speaker.

2.2.1.1 SIP Talk-Back Speaker to a 802.3af Compliant PoE Switch

Figure 2-1 illustrates how to connect the SIP Talk-Back Speaker to a 802.3af compliant PoE switch

via a Cat 5 Ethernet cable.

Figure 2-1. SIP Talk-Back Speaker to a 802.3af Compliant PoE Switch

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

PoE Injector (Part #010867A)

Non PoE Switch

SIP Talk-Back Speaker

Cat 5 Ethernet cable

Device Configuration

2.2.1.2 SIP Talk-Back Speaker (with PoE Injector) to a 802.3af Compliant PoE Switch

In Figure 2-2, if a PoE switch is not available, you will need a PoE Injector, part #010867A (ordered separately). A PoE Injector is a power supply solution for those who have a standard Non PoE Switch.

Figure 2-2. SIP Talk-Back Speaker (with PoE Injector) to a Non PoE Switch

Operations Guide 931191I CyberData Corporation

2.2.1.3 Running the SIP Talk-Back Speaker with Auxiliary Power

GENERAL ALERT

GND

AC adaptor +12-24 VDC @ 1 Amps (UL-listed, LPS-rated)

+12-24 VDC

Speaker

AUX SPEAKER (-) AUX SPEAKER (+) GND LINE OUT (-) LINE OUT (+)

+5V OUT

RELAY NO

RELAY COM

AUX POWER (-)

AUX POWER (+)

(+24VDC @ 1A)

J10

N/C

CLASS II WIRING

In Figure 2-3, the power for the SIP Talk-Back Speaker can either come from an 802.3af Network connection or from an external source.

Caution

Operational Note: Do not connect an auxiliary power supply when the SIP

Talk-Back Speaker is connected to a PoE power source through J1. Improper operation or equipment damage may occur.

Installing the SIP Talk-Back Speaker

Device Configuration

Figure 2-3. Running the Speaker with Auxiliary Pow

Operations Guide 931191I CyberData Corporation

2.2.2 Installation Options

Port C over

Flip Over

Ceiling Speaker Assembly

Mounting Screw

Strobe Cable

One (1) Meter

Slot

Backplate

RGB Strobe Assembly

Connect Through Backplate / Slot

071069*

Mounting Screw

Cable

Adapter

Key Bump

Slot

Dimple

Auxiliary RGB Strobe

This section shows various installation options for the SIP Talk-Back Speaker.

2.2.2.1 Connecting the Auxiliary RGB Strobe to the SIP SPeaker

1. Connect the one meter strobe cable to the adapter cable. See Figure 2-4.

2. Remove the mounting screws and port cover from the SIP Speaker. See Figure 2-4.

3. Align the key bump on the adapter cable to the key bump slot on the SIP Speaker. See Figure 2-

4. Replace the port cover and mounting screw. See Figure 2-4.

Figure 2-4. Connecting the Auxiliary RGB Strobe Kit to the SIP Speaker

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

2.2.2.2 Connecting the SIP RGB Strobe to the SIP SPeaker

Port C over

Flip Over

Ceiling Speaker Assembly

Mounting Screw

Strobe Cable

One (1) Meter

Connect Through Backplate / Slot

071069*

Cable

Adapter

Key Bump

Slot

Dimple

SIP RGB Strobe Board

1. Connect the one meter strobe cable to the adapter cable. See Figure 2-5.

2. Remove the mounting screws and port cover from the SIP Speaker. See Figure 2-5.

3. Align the key bump on the adapter cable to the key bump slot on the SIP Speaker. See Figure 2-

4. Replace the port cover and mounting screw. See Figure 2-4.

Figure 2-5. Connecting the SIP RGB Strobe to the SIP Speaker

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Speaker

Back View

AUX SPEAKER (-) AUX SPEAKER (+) GND LINE OUT (-) LINE OUT (+) BUTTON LED (-)

BTN SENSE

BUTTON LED (+)

RELAY NO

RELAY COM

AUX POWER (-)

AUX POWER (+)

(+24VDC @ 1A)

J10

CLASS II WIRING

High-purity copper 16 AWG wire and a maximum length of 20 feet

Remote Call Button Note: See Section 1.9.1, "Optional 011185

Remote Call Button (sold separately)"

2.2.2.3 Running the SIP Talk-Back Speaker with a Remote Call Button

Note Figure 2-3 shows the optional 011185 Remote Call Button (sold separately). See Section

1.9.1, "Optional 011185 Remote Call Button (sold separately)"

In Figure 2-3, the optional Remote Call Button (sold separately) enables calls to the SIP Talk-Back Speaker that can be initiated or answered from a remotely-mounted switch. When enabled through the web interface, if the Remote Call Button is pressed, the speaker would initiate a SIP call to a predetermined extension.

When the SIP Talk-Back Speaker is called from a remote phone and Auto-Answer is not enabled within the unit’s Web interface, the LED on the Remote Button will blink. The call will be answered when the button is pressed.

Figure 2-6. Running the Speaker with a Remote Call Button

Device Configuration

Operations Guide 931191I CyberData Corporation

2.2.2.4 SIP Talk-Back Speaker with an External Device

AUX SPEAKER (-) AUX SPEAKER (+) GND LINE OUT (-) LINE OUT (+) BUTTON LED (-)

BTN SENSE

BUTTON LED (+)

RELAY NO

RELAY COM

AUX POWER (-)

AUX POWER (+)

(+24VDC @ 1A)

J10

CLASS II WIRING

High PIV Ultrafast Switching Diode

Output Contacts AC or DC-rated depending upon controlled device requirements

DC Power Supply (Max. 30 VDC @ 1A)

Solid State or  Mechanical Relay

AC or DC Power Source as required by an external device

OUT

External device such as an electric door strike or LED strobe light

Speaker

In Figure 2-7, when the SIP Talk-Back Speaker is called from a remote phone, the relay on the speaker can be programmed to drive an external device such as an alert strobe. This external device may also be addressed from a separate Unified Communication (UC) server.

Figure 2-7. Speaker with an External Device

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

2.2.2.5 SIP Talk-Back Speaker with Auxiliary Speaker Connection

GENERAL ALERT

8 Ohm Auxiliary Speaker

High-purity copper 16-gauge wire and a maximum length of 20 feet

Speaker

(Part #011120, RAL 9002)

*When using the second speaker connection, 

the analog volume control needs to be disabled.

*Because of the limitations of PoE power, 

when running the Speaker with a second auxiliary speaker, the analog or digital volume level setting must not exceed a setting of 6.

(Part #011121, RAL 9003)

AUX SPEAKER (-) AUX SPEAKER (+) GND LINE OUT (-) LINE OUT (+)

+5V OUT

RELAY NO

RELAY COM

AUX POWER (-)

AUX POWER (+)

(+24VDC @ 1A)

J10

N/C

CLASS II WIRING

In Figure 2-8, the SIP Talk-Back Speaker supports an amplified audio output for a second analog speaker. While the total speaker wattage is the same, by connecting a low cost analog speaker, a

dditional coverage can be realized

Caution

Operational Note: The SIP speaker dynamically adjusts volume to properly

budget power when accessories are connected. For best performance, it is recommended that either an 802.3AT or 24V auxiliary power source is used when connecting an auxiliary speaker and a clock kit.

Figure 2-8. SIP Talk-Back Speaker with Auxiliary Speaker Connection

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

2.2.2.6 SIP Talk-Back Speaker with Line Out

AUX SPEAKER (-) AUX SPEAKER (+) GND LINE OUT (-) LINE OUT (+) BUTTON LED (-)

BTN SENSE

BUTTON LED (+)

RELAY NO

RELAY COM

AUX POWER (-)

AUX POWER (+)

(+24VDC @ 1A)

J10

CLASS II WIRING

Office area in Factory

Factory Floor

Amplifier

Line Out: Output Signal Amplitudes 2.0 VPP maximum Output Level +2dBm nominal Total Harmonic Distortion 0.5% maximum Output Impedance 10k ohm

Speaker

In Figure 2-9, for areas that require more speaker volume, the SIP Talk-Back Speaker can be connected directly to an auxiliary amplifier to drive additional horns or speakers. This is done through the line-out connection.

Figure 2-9. SIP Talk-Back Speaker with Line Out

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Speaker Status (Green)

Network  Link/Activity (Yellow)

Device Configuration

2.2.3 Confirm that the Speaker is Operational and Linked to the Network

After connecting the speaker to the 802.3af compliant Ethernet hub, the LEDs on the speaker face confirm that the speaker is operational and linked to the network.

Figure 2-10. Status and Activity LEDs

2.2.3.1 Status LED

After supplying power to the speaker:

1. The green power/status LED and the yellow network LED comes on immediately.

2. After about 23 seconds with a static IP address (or 27 seconds if the board is set to use DHCP), the green LED will blink twice to indicate that the board is fully booted. The speaker will beep at this time if the

2.3.5).

Note If the board is set to use DHCP and there is not a DHCP server available on the network, it

will try 12 times with a three second delay between tries and eventually fall back to the programmed static IP address (by default 10.10.10.10). This process will take approximately 80 seconds.

Note The front power/status LED will remain solid on during operation.

Beep on Init option is enabled on the Device Configuration Page (see Section

2.2.3.2 Link LED

• The Link LED is illuminated when the network link to the speaker is established.

• The Link LED blinks to indicate network traffic.

Operations Guide 931191I CyberData Corporation

2.2.4 Confirm the IP Address and Test the Audio

RTFM button

2.2.4.1 Reset Test Function Management (RTFM) Button

When the speaker is operational and linked to the network, use the Reset Test Function Management (RTFM) button ( speaker’s IP Address and test that the audio is working.

Note Using the RTFM button will lock the digital volume level to 4 and disable the analog volume

control dial.

Figure 2-11) on the speaker face to announce and confirm the

Figure 2-11. RTFM Button

Installing the SIP Talk-Back Speaker

Device Configuration

To announce a speaker’s current IP address, press and release the RTFM button within a five second window.

Note The speaker will use DHCP to obtain the new IP address (DHCP-assigned address or

default to 10.10.10.10 if a DHCP server is not present).

Note Pressing and holding the RTFM button for longer than five seconds will restore the speaker

to the factory default settings.

Operations Guide 931191I CyberData Corporation

2.2.5 Adjust the Volume

Volume control dial

To adjust the speaker volume, turn the Volume control dial (Figure 2-12) on the speaker face.

Note The SIP Talk-Back Speaker has two volume controls: Internal (web-based) and External

(volume knob). The external volume control can be disabled from the web interface by selecting

2.3.5).

Installing the SIP Talk-Back Speaker

Device Configuration

Disable Volume Control Dial on the Device Configuration Page (see Section

Figure 2-12. Volume Control

Operations Guide 931191I CyberData Corporation

2.2.6 How to Set the Factory Default Settings

RTFM button

2.2.6.1 RTFM Button

When the speaker is operational and linked to the network, use the Reset Test Function Management (RTFM) button (

Figure 2-13) on the speaker face to set the factory default settings.

Figure 2-13. RTFM Button

Installing the SIP Talk-Back Speaker

Device Configuration

To set the factory default settings:

1. Press and hold the RTFM button for more than five seconds.

2. The speaker announces that it is restoring the factory default settings.

Note The speaker will use DHCP to obtain the new IP address (DHCP-assigned address or

default to 10.10.10.10 if a DHCP server is not present).

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

2.3 Configure the SIP Talk-Back Speaker Parameters

To configure the SIP Talk-Back Speaker online, use a standard web browser.

Configure each SIP Talk-Back Speaker and verify its operation bef ready to mount an SIP Talk-Back Speaker, refer to Appendix A, "Mounting the Speaker" for instructions.

2.3.1 Factory Default Settings

All SIP Talk-Back Speakers are initially configured with the following default IP settings:

When configuring more than one SIP Talk-Back Speaker, attach the SIP Talk-Back Speakers to the

etwork and configure one at a time to avoid IP address conflicts.

Parameter Factory Default Setting

IP Addressing DHCP

IP Address

Web Access Username admin

Web Access Password admin

Subnet Mask

Default Gateway

Table 2-3. Factory Default Settings

10.10.10.10

255.0.0.0

10.0.0.1

ore you mount it. When you are

a. Default if there is not a DHCP server present.

Operations Guide 931191I CyberData Corporation

2.3.2 SIP Talk-Back Speaker Web Page Navigation

Ta bl e 2-4 shows the navigation buttons that you will see on every SIP Talk-Back Speaker web page.

Table 2-4. Web Page Navigation

Web Page Item Description

Link to the Home page.

Link to the Device page.

Installing the SIP Talk-Back Speaker

Device Configuration

Link to the Netw

Link to go to the SIP pag

Link to the Multicast page.

Link to the Sensor page.

Link to the Audiofiles page.

Link to the Events page.

Link to the Autoprovisioning page.

Link to the Firmwar

ork page.

e page.

Operations Guide 931191I CyberData Corporation

2.3.3 Using the Toggle Help Button

Toggle Help button

Question mark  appears next to the web page items

The Toggle Help button allows you to see a short description of some of the settings on the webpage. To use the Toggle Help button, do the following:

Installing the SIP Talk-Back Speaker

Device Configuration

1. Click on the T

oggle Help button that is on the UI webpage. See Figure 2-14 and Figure 2-15.

Figure 2-14. Toggle/Help Button

2. You will see a question mark (

) appear next to each web page item that has been provided

with a short description by the Help feature. See Figure 2-15.

Figure 2-15. Toggle Help Button and Question Marks

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

A short description of the  web page item will appear

Question mark

Device Configuration

3. Move the mouse pointer to hover over the question mark ( ), and a short description of the web page item will appear. See Figure 2-16.

Figure 2-16. Short Description Provided by the Help Feature

Operations Guide 931191I CyberData Corporation

2.3.4 Log in to the Configuration Home Page

Note The version of InformaCast needs to be 4.0 or higher.

4. Open your browser to the SIP Talk-Back Speaker IP address.

Note If the network does not have access to a DHCP server, the device will default to an IP

address of 10.10.10.10.

Note Make sure that the PC is on the same IP network as the SIP Talk-Back Speaker.

Note You may also download CyberData’s VoIP Discovery Utility program which allows you to

easily find and configure the default web address of the CyberData VoIP products.



CyberData’s VoIP Discovery Utility program is available at the following website address:

http://www.cyberdata.net/assets/common/discovery.zip

Note The device ships in DHCP mode. To get to the Home page, use the discovery utility to scan

for the device on the network and open your browser from there.

5. When prompted, use the following default Web Access Username and Web Access Password to access the Home Page (

Web Access Username: admin

Web Access Password: admin

Figure 2-17):

Installing the SIP Talk-Back Speaker

Device Configuration



Operations Guide 931191I CyberData Corporation

Figure 2-17. Home Page

v11.6.9

397100001

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

6. On the Home page, review the setup details and navigation buttons described in Ta bl e 2-5.

Note The question mark icon (

after the T

oggle Help button is pressed.

) in the following table shows which web page items will be defined

Table 2-5. Home Page Overview

Web Page Item

Description

Admin Settings

Username The username to access the web interface. Enter up to 25 characters.

Password

Confirm Password

The password to access the web interface. Enter up to 25 characters.

Confirm the web interface password.

Current Status

Serial Number Shows the device serial number.

Mac Address Shows the device Mac address.

Firmware Version Shows the current firmware version.

IP Addressing Shows the current IP addressing setting (D

HCP or static).

IP Address Shows the current IP address.

Subnet Mask Shows the current subnet mask address.

Default Gateway Shows the current default gateway address.

DNS Server 1 Shows the current DNS Server 1 address.

DNS Server 2 Shows the current DNS Server 2 address.

SIP Mode Shows the current status of the SIP mode.

Multicast Mode Shows the current status of the Multicast mode.

Event Reporting Shows the current status of the Event Reporting mode.

Nightringer Shows the current status of the Nightringer mode.

Primary SIP Server Shows the current status of the Primary SIP Server.

Backup Server 1 Shows the current status of Backup Server 1.

Backup Server 2 Shows the current status of Backup Server 2.

Nightringer Server Shows the current status of Nightringer Server.

Monitor SIP Server

Shows the current status of the Monitor SIP Server.

Import Settings

Use this button to select a configuration file to import.

After selecting a configuration file, click Import to import the configuration from the selected file. Then, click Save and Reboot to store changes.

Export Settings

Click Export to export the current configuration to a file.

Operations Guide 931191I CyberData Corporation

Table 2-5. Home Page Overview (continued)

Web Page Item Description

Click the Save button to save your configuration settings.

Note: You need to reboot for changes to take effect.

Click on the Reboot button to reboot the system.

Click on the Toggle Help button to see a short description of some of the web page items. First click on the Toggle Help button, and you will see a question mark ( Move the mouse pointer to hover over a question mark to see a short description of a specific web page item.

Installing the SIP Talk-Back Speaker

Device Configuration

) appear next to some of the web page items.

Operations Guide 931191I CyberData Corporation

2.3.5 Configure the Device

These settings will only appear if you are using the Talk-Back Speaker. If you are not using the Talk-Back Speaker, you will see the words NOT INSTALLED.

1. Click the Device menu button to open the Device page. See Figure 2-18.

Figure 2-18. Device Configuration Page

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

Figure 2-19. Device Configuration Page

These settings will only appear if you are using the Clock Kit. If you are not using the Clock Kit, you will see the words

NOT INSTALLED

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

2. On the Device page, you may enter values for the parameters indicated in Tab l e 2-6.

Note The question mark icon (

after the To

ggle Help button is pressed.

) in the following table shows which web page items will be defined

Table 2-6. Device Configuration Parameters

Web Page Item Description

Volume Settings (0-9)

Disable Volume Control Dial Select this option to disable the volume control dial and enable digital

volume control settings.

SIP Volume

Set the speaker volume for a SIP call. A value of 0 will mute the speaker during SIP calls.

Multicast Volume

Set the speaker volume for multicast audio streams. A value of 0 will mute the speaker during multicasts.

Ring Volume

Set the ring volume for incoming calls. A value of 0 will mute the speaker instead of playing the ring tone when Auto-Answer Incoming Calls is disabled.

Sensor Volume

Set the speaker volume for playing sensor activated audio. A value of 0 will mute the speaker during sensor activated audio.

Push To Talk Volume

Set the speaker volume for Push to Talk operation. A value of 0 will mute the speaker in Push to Talk mode.

Volume Boost:

No Volume Boost

Set the Boost level to increase the volume output of the speaker. Using Volume Boost may introduce audio clipping and/or distortion. Boost is only recommended for use with volumes set to level 9.

+4dB

DTMF Settings

Require Security Code When selected, the user will be prompted to enter a Security Code

(entered on this page) before being able to execute a page when calling the device.

Security Code

Type the Security Code in this field. The Security Code must only use characters '0-9', '*' and '#'. Enter up to 25 characters.

Enable DTMF Push to Talk

This option is for noisy environments.When enabled, in an active call the remote phone can force receive only audio (setting the mic gain to max and muting the speaker) by pressing the '*' key. Pressing the '#' key will force send only audio (setting the max speaker volume and muting the mic). Pressing the '0' key will restore full duplex operation with the normal microphone and speaker volume.

Monitor DTMF Toggle Key

Specify the key that toggles between monitor mode's 'talk' and 'listen' state. Defaults to '#'.

Note: Some PBX's use # for other call functions

Enable Stored Message Playback

When selected, the caller will be prompted to select one of nine stored messages to play through the speaker. Stored messages may be customized on the Audiofiles page.

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

Table 2-6. Device Configuration Parameters (continued)

Web Page Item Description

Time Settings

Set Time with NTP Server on boot When selected, the time is set with an external NTP server when the

device restarts.

NTP Server

Use this field to set the address (in IPv4 dotted decimal notation or as a canonical name) for the NTP Server. This field can accept canonical names of up to 64 characters in length.

Posix Timezone String

See Section 2.3.5.1, "Time Zone Strings" for information about how to use the Posix Timezone String to specify time zone and daylight savings time where applicable. Enter up to 63 characters.

Periodically sync time with server

When selected, the time is periodically updated with the NTP server at the configured interval below.

Time update period (in hours)

The time interval after which the device will contact the NTP server to update the time. Enter up to 4 digits.

Current Time

Set Time Manually

Allows you to input the current time. (6 character limit)

Set the system time when NTP is not enabled. Format is HH:MM:SS

Clock Settings These settings will only appear if you are using the Clock Kit. If you

are not using the Clock Kit, you will see the words NOT INSTALLED.

Clock Kit

Clock Brightness (0 - 14)

Use Ambient Light Sensor

Clock Colon Type

Use 24 Hour Time

Displays the status of optional Clock Kit.

This setting allows you to select the clock brightness level (0-14).

This setting enables or disables the ambient light sensor.

This setting allows you to select the clock colon type.

When selected, the time will be show in 24 hour format on the optional clock display.

Button Settings

Button Installed When selected, the speaker is assumed to be wired to a push-to-talk

button. Button settings will be enabled and sensor settings will be disabled. When not selected, the speaker is assumed to be wired to a sensor. Sensor settings will be enabled and button settings will be disabled.

Activate Relay On Button Press

When selected, the relay will be activated when the Call button is pressed.

Relay On Button Press Duration

The length of time (in seconds) during which the relay will be activated when the Call button is pressed. Enter up to 5 digits. A Relay on Button Press Duration value of 0 will pulse the relay once when the Call button is pressed.

Button Lit when Idle When selected, the Call button LED is illuminated while the device is idle

(a call is not in progress).

Button Brightness (0-255)

The desired Call button LED brightness level. Acceptable values are 0255, where 0 is the dimmest and 255 is the brightest. Enter up to 3 digits.

Play Ringback Tone

When selected, the device will play a ringback tone (corresponds to Ringback Tone on the Audiofiles page) out of the speaker while placing an outbound call. The Ringback Tone will play until the call is answered.

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

Table 2-6. Device Configuration Parameters (continued)

Web Page Item Description

Enable Push to Talk This option is for noisy environments. When enabled, the microphone

will be muted normally. When the Call button is pressed and held, it will unmute the microphone and allow the operator to send audio back. Using Push to Talk prevents the operator from terminating a call by pressing the Call button. The call must be terminated by the phone user.

Prevent Call Termination

When this option is enabled, a call cannot be terminated using the call button.

Blink Button LED on monitor call

Selecting this will cause the button LED blink during a monitor call. Unselecting this will cause the speaker to give no indication that it is in a monitor call.

Microphone Settings These settings will only appear if you are using the Talk-Back

Speaker. If you are not using the Talk-Back Speaker, you will see the words NOT INSTALLED.

Microphone

Microphone Gain

Displays the status of optional microphone.

Set the microphone gain level.

Push to Talk Microphone Gain

Microphone Boost 1 (+20dB)

Set the microphone gain level for Push to Talk operation.

Enables one of two +20dB gain boosts on the microphone when checked.

Microphone Boost 2 (+20dB)

Enables one of two +20dB gain boosts on the microphone when checked.

Power Settings

802.3AT Mode This device automatically detects if it is plugged into an 802.3AT (also known as PoE Plus) power source. 802.3AT provides more power than older 802.3AT power sources and allows this speaker to play audio at higher volumes. If you are sure this speaker is connected to an 802.3AT power source, but it is not being detected correctly, you can override the automatic settings below.

Force 802.3AT Mode (NOT recommended) Enable this option if you are sure this speaker is connected to an

802.3AT power source, but it is not being detected correctly (not recommended).

Auxiliary Power Supply

This device can be connected to a +24VDC auxiliary power supply. Check this box if this is how this speaker is being powered.

Relay Settings

Activate Relay with DTMF Code Activates the relay when the DTMF Activation Code is entered on the

phone during a SIP call with the device. RFC2833 DTMF payload types are supported.

Relay Pulse Code

DTMF code used to pulse the relay when entered on a phone during a SIP call with the device. Relay will activate for Relay Pulse Duration seconds then deactivate. Activate Relay with DTMF Code must be enabled. Enter up to 25 digits (* and # are supported).

Relay Pulse Duration (in seconds)

The length of time (in seconds) during which the relay will be activated when the DTMF Relay Activation Code is detected. Enter up to 5 digits.

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

Table 2-6. Device Configuration Parameters (continued)

Web Page Item Description

Relay Activation Code Activation code used to activate the relay when entered on a phone

during a SIP call with the device. Relay will be active indefinitely, or until the DTMF Relay Deactivation code is entered. Activate Relay with DTMF Code must be enabled. Enter up to 25 digits (* and # are supported).

Relay Deactivation Code

Code used to deactivate the relay when entered on a phone during a SIP call with the device. Activate Relay with DTMF Code must be enabled. Enter up to 25 digits (* and # are supported).

Activate Relay During Ring

When selected, the relay will be activated for as long as the device is ringing. When Auto-Answer Incoming Calls is enabled, the device will not ring and this option does nothing.

Activate Relay During Night Ring

When selected, the relay will be activated as long as the Nightringer extension is ringing.

Activate Relay While Call Active

When selected, the relay will be activated as long as the SIP call is active.

Misc Settings

Device Name Type the device name. Enter up to 25 characters.

Auto-Answer Incoming Calls

When selected, the device will automatically answer incoming calls. When Auto-Answer Incoming Calls is disabled, the device will play a ring tone (corresponds to Ring Tone on the Audiofiles page) out of the speaker until someone presses the Call button to answer the call or the caller disconnects before the call can be answered.

Beep on Init

Beep on Page

Device will play the user-defined “pagetone” audio file when it boots.

Device will play the user defined “pagetone” audio file before playing a SIP page.

Disable HTTPS (NOT recommended)

Disables the encrypted connection to the webpage. We do not recommend disabling HTTPS for security reasons.

Dual Speakers

Select this option if two speakers (main and auxiliary) are connected to the board.

RGB Strobe

Status of optional RGB Strobe.

Click on the Test Audio button to do an audio test. When the Test Audio button is pressed, you will hear a voice message for testing the device audio quality and volume.

Click on the Test Microphone button to do a microphone test. When the Test Microphone button is pressed, the following occurs:

1. The device will immediately start recording 3 seconds of audio.

2. The device will beep (indicating the end of recording).

3. The device will play back the recorded audio.

Click on the Test Relay button to do a relay test.

Click the Save button to save your configuration settings.

Note:

You need to reboot for changes to take effect.

Operations Guide 931191I CyberData Corporation

Table 2-6. Device Configuration Parameters (continued)

Web Page Item Description

Click on the Reboot button to reboot the system.

Note You can change the SIP Volume, Multicast Volume, Ring Volume, Sensor Volume, and

Push To Talk Volume without rebooting the device. You must save and reboot the device

for other changes to take effect.

Installing the SIP Talk-Back Speaker

Device Configuration

) appear next to some of the web page items.

Operations Guide 931191I CyberData Corporation

2.3.5.1 Time Zone Strings

The posix time zone string tells the internal date and time utilities how to handle daylight savings time for different time zones. Ta bl e 2-19 shows some common strings.

Time Zone Time Zone String

US Pacific time PST8PDT,M3.2.0/2:00:00,M11.1.0/2:00:00

US Mountain time MST7MDT,M3.2.0/2:00:00,M11.1.0/2:00:00

US Eastern Time EST5EDT,M3.2.0/2:00:00,M11.1.0/2:00:00

Phoenix Arizona

US Central Time CST6DST,M3.2.0/2:00:00,M11.1.0/2:00:00

a.Phoenix, Arizona does not use daylight savings time.

Ta bl e 2-20 shows a breakdown of the parts that constitute the following time zone string:

● CST6DST,M3.2.0/2:00:00,M11.1.0/2:00:00

Installing the SIP Talk-Back Speaker

Device Configuration

Table 2-7. Common Time Zone Strings

MST7

Table 2-8. Time Zone String Parts

Time Zone String

Meaning

Part

CST6CDT The time zone offset from GMT and three character identifiers for the time zone.

CST Central Standard Time

6 The (hour) offset from GMT/UTC

CDT

Central Daylight Time

M3.2.0/2:00:00 The date and time when daylight savings begins.

M3 The third month (March)

.2 The 2nd occurrence of the day (next item) in the month

.0 Sunday

/2:00:00

Time of day to change

M11.1.0/2:00:00 The date and time when daylight savings ends.

M11 The eleventh month (November)

.1 The 1st occurrence of the day (ne

xt item) in the month

.0 Sunday

/2:00:00 Time of day to change

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

Time Zone String Examples

Time Zone Identifier

Ta bl e 2-21 has some more examples of time zone strings.

Table 2-9. Time Zone String Examples

Time Zone Time Zone String

Tokyo

Berlin

IST-9

CET-1MET,M3.5.0/1:00,M10.5.0/1:00

a.Tokyo does not use daylight savings time. b.For Berlin, daylight savings time starts on the last Sunday in March at 01:00 UTC, and ends on the last Sunday in October at 01:00 UTC, and is one hour ahead of UTC.

A user-definable three or four character time zone identifier (such as PST, EDT, IST, MUT, etc) is needed at the beginning of the posix time zone string to properly set the time. However, the specific letters or numbers used for the time zone identifier are not important and can be any three or four letter or number combination that is chosen by the user. However, the time zone identifier cannot be blank.

Figure 2-20. Three or Four Character T

ime Zone Identifier

You can also use the following URL when a certain time zone applies daylight savings time:

http://www.timeanddate.com/time/dst/2011.html

World GMT Table

Ta bl e 2-22 has information about the GMT time in various time zones.

Table 2-10. World GMT Table

Time Zone City or Area Zone Crosses

GMT-12 Eniwetok

GMT-11 Samoa

GMT-10 Hawaii

GMT-9 Alaska

GMT-8 PST, Pacific US

GMT-7 MST, Mountain US

GMT-6 CST, Central US

GMT-5 EST, Eastern US

GMT-4 Atlantic, Canada

GMT-3 Brazilia, Buenos Aries

GMT-2 Mid-Atlantic

GMT-1 Cape Verdes

GMT Greenwich Mean Time, Dublin

GMT+1 Berlin, Rome

GMT+2 Israel, Cairo

GMT+3 Moscow, Kuwait

GMT+4 Abu Dhabi, Muscat

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Table 2-10. World GMT Table (continued)

Time Zone City or Area Zone Crosses

GMT+5 Islamabad, Karachi

GMT+6 Almaty, Dhaka

GMT+7 Bangkok, Jakarta

GMT+8 Hong Kong, Beijing

GMT+9 Tokyo, Osaka

GMT+10 Sydney, Melbourne, Guam

GMT+11 Magadan, Soloman Is.

GMT+12 Fiji, Wellington, Auckland

Device Configuration

Operations Guide 931191I CyberData Corporation

2.3.6 Configure the Network Parameters

1. Click the Network menu button to open the Network page (Figure 2-21).

Figure 2-21. Network Configuration Page

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

2. On the Network page, enter values for the parameters indicated in Ta bl e 2-11.

Note The question mark icon (

after the To

ggle Help button is pressed.

) in the following table shows which web page items will be defined

Table 2-11. Network Configuration Parameters

Web Page Item Description

Stored Network Settings

Addressing Mode Select either DHCP IP Addressing or Static Addressing by marking

the appropriate radio button. DHCP Addressing mode is enabled on default and the device will attempt to resolve network addressing with the local DHCP server upon boot. If DHCP Addressing fails, the device will revert to the last known IP address or the factory default address if no prior DHCP lease was established. See Section 2.3.1,

"Factory Default Settings" for factory default settings. Be sure to click

Save and Reboot to store changes when configuring a Static address.

Hostname This is the hostname provided by the DHCP server. See the

DHCP/DNS server documentation for more information. Enter up to 64 characters.

IP Address Enter the Static IPv4 network address in dotted decimal notation.

Subnet Mask Enter the Subnet Mask in dotted decimal notation.

Default Gateway Enter the Default Gateway IPv4 address in dotted decimal notation.

DNS Server 1 Enter the primary DNS Server IPv4 address in dotted decimal

notation.

DNS Server 2 Enter the secondary DNS Server IPv4 address in dotted decimal

notation.

DHCP Timeout in seconds Specify the desired time-out duration (in seconds) that the device will

wait for a response from the DHCP server before reverting back to the stored static IP address. The stored static IP address may be the last known IP address or the factory default address if no prior DHCP lease was established. Enter up to 8 characters. A value of -1 will retry forever.

VLAN Settings

VLAN ID (0-4095) Specify the IEEE 802.1Q VLAN ID number. Enter up to 4 digits.

Note: The device supports 802.1Q VLAN tagging support. The switch port connected to the device will need to be in “trunking mode” for the VLAN tags to propagate.

VLAN Priority (0-7) Specify the IEEE 802.1p VLAN priority level. Enter 1 digit. A value of

0 may cause the VLAN ID tag to be ignored.

Current Network Settings Shows the current network settings.

IP Address Shows the current Static IP address.

Subnet Mask Shows the current Subnet Mask address.

Default Gateway Shows the current Default Gateway address.

DNS Server 1 Shows the current DNS Server 1 address.

DNS Server 2 Shows the current DNS Server 2 address.

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

Table 2-11. Network Configuration Parameters (continued)

Web Page Item Description

Click the Save button to save your configuration settings.

Note: You need to reboot for changes to take effect.

Click on the Reboot button to reboot the system.

Click on the Togg le Hel p button to see a short description of some of the web page items. First click on the Toggle Help button, and you will see a question mark ( ) appear next to some of the web page items. Move the mouse pointer to hover over a question mark to see a short description of a specific web page item.

Note You must click on the Save button and then the Reboot button for the changes to take

effect.

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

The strobe settings will only appear if you are using the Strobe Kit. If you are not using the Strobe Kit, you will not see the strobe settings.

2.3.7 Configure the SIP (Session Initiation Protocol) Parameters

1. Click on the SIP menu button to open the SIP page (Figure 2-22).

Figure 2-22. SIP Configuration Page—Top

Device Configuration

Operations Guide 931191I CyberData Corporation

Figure 2-23. SIP Configuration Page—Bottom

The strobe settings will only appear if you are using the Strobe Kit. If you are not using the Strobe Kit, you will not see the strobe settings.

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

2. On the SIP page, enter values for the parameters indicated in Ta b le 2-12.

Device Configuration

Note The question mark icon (

after the To

ggle Help button is pressed.

) in the following table shows which web page items will be defined

Table 2-12. SIP Configuration Parameters

Web Page Item Description

SIP Settings

Enable SIP Operation When enabled, the device will transmit, receive, and process SIP messages according

to the configured SIP settings below.

this page. To configure the device to send and receive point-to-point SIP calls, enable SIP Operation and disable Register with a SIP Server (see Section 2.3.7.2, "Point-

to-Point Configuration").

Use Cisco SRST When enabled, the backup servers are handled according to Cisco SRST (Survivable

Remote Site Telephony). It is required for use in clustered Cisco Unified Communications Manager topologies.

Primary SIP Server Enter the SIP server address as an IPv4 address in dotted decimal notation or a fully

qualified domain name. This parameter also becomes the host portion of the SIP-URI for the device's extension on the primary SIP server. This field can accept entries of up to 255 characters in length.

Primary SIP User ID Specify the SIP User ID for the Primary SIP Server. This parameter becomes the user

portion of the SIP-URI for the device's extension on the primary SIP server. Enter up to 64 alphanumeric characters.

Primary SIP Auth ID Specify the Authenticate ID for the Primary SIP Server. This parameter is required for

SIP registration authentication. Enter up to 64 alphanumeric characters.

Primary SIP Auth Password Specify the Authenticate Password for the Primary SIP Server. This parameter is

required for SIP registration authentication. Enter up to 64 alphanumeric characters.

Backup SIP Server 1 Enter the backup SIP server address as an IPv4 address in dotted decimal notation or

a fully qualified domain name. This parameter also becomes the host portion of the SIP-URI for the device's extension on the backup SIP server. This field can accept entries of up to 255 characters in length.

Backup SIP User ID 1 Specify the SIP User ID for the first backup SIP Server. This parameter becomes the

user portion of the SIP-URI for the device's extension on the first backup SIP server. Enter up to 64 alphanumeric characters.

Backup SIP Auth ID 1 Specify the Authenticate ID for the first backup SIP server. This parameter is required

for SIP registration authentication. Enter up to 64 alphanumeric characters.

Backup SIP Auth Password 1 Specify the Authenticate Password for the first backup SIP server. This parameter is

required for SIP registration authentication. Enter up to 64 alphanumeric characters.

Backup SIP Server 2 Enter a second backup SIP server address as an IPv4 address in dotted decimal

notation or a fully qualified domain name. This parameter also becomes the host portion of the SIP-URI for the device's extension on the second backup SIP server. This field can accept entries of up to 255 characters in length.

Backup SIP User ID 2 Specify the SIP User ID for the second backup SIP Server. This parameter becomes

the user portion of the SIP-URI for the device's extension on the second backup SIP server. Enter up to 64 alphanumeric characters.

Backup SIP Auth ID 2 Specify the Authenticate ID for the second backup SIP server. This parameter is

required for SIP registration authentication. Enter up to 64 alphanumeric characters.

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

Table 2-12. SIP Configuration Parameters (continued)

Web Page Item Description

Backup SIP Auth Password 2 Specify the Authenticate Password for the second backup SIP server. This parameter

is required for SIP registration authentication. Enter up to 64 alphanumeric characters.

Remote SIP Port The Remote SIP Port is the port number the device will use as the destination port

when sending SIP messages. The default Remote SIP Port is 5060. The supported range is 0-65536. Enter up to 5 digits.

Local SIP Port The Local SIP Port is the port number the device will use to receive SIP messages.

The default Local SIP Port is 5060. The supported range is 0-65536. Enter up to 5 digits.

Outbound Proxy Enter the Outbound Proxy address as an IPv4 address in dotted decimal notation or a

fully qualified domain name (FQDN). When an IP address is configured, the device will send all SIP messages to this IP address. When an FQDN is configured, the device will run DNS NAPTR, SRV, and A queries on the FQDN to resolve an IP address to which it will send all SIP messages. This field can accept entries of up to 255 characters in length.

Outbound Proxy Port The Outbound Proxy Port is port number used as the destination port when sending

SIP messages to the outbound proxy. A value of 0 will default to 5060. The supported range is 0-65536. Enter up to 5 digits.

Monitor User ID Specify the SIP User ID for the SIP server. This parameter becomes the user portion

of the SIP-URI for the device's Monitor Mode extension. Enter up to 64 alphanumeric characters.

Monitor Authenticate ID Specify the Authenticate ID for the SIP Server. This parameter is required for SIP

registration authentication. Enter up to 64 alphanumeric characters.

Monitor Authenticate Password Specify the Authenticate Password for the SIP Server. This parameter is required for

SIP registration authentication. Enter up to 64 alphanumeric characters.

Disable rport Discovery Disabling rport Discovery will prevent the device from including the public WAN IP

address and port number in the contact information that is sent to the remote SIP servers. This will generally only need to be enabled when using an SBC or SIP ALG in conjunction with a remote SIP server.

Buffer SIP Calls Also referred to as delayed paging. Device will buffer up to 4 minutes of audio then

play back the recording after hang up.

Re-registration Interval (in seconds) The SIP Re-registration interval (in seconds) is the SIP Registration lease time, also

known as the expiry. The supported range is 30-3600 seconds. Enter up to 4 digits.

Unregister on Boot When enabled, the device will send one registration with an expiry of 0 on boot.

Keep Alive Period The minimum time in milliseconds between keep-alive packets sent for nat traversal. A

value of 0 will disable keep alive packets.

SIP Ring Strobe Settings The following strobe settings will only appear if a CyberData Strobe product is

connected to your device. If a CyberData Strobe product is not connected to your device, you will not see the strobe settings.

Blink Strobe on Ring When selected, the Strobe will blink a scene when ringing.

Scene Select desired scene (only one may be chosen).

ADA Compliant Strobe will blink ON at the specified brightness for 150ms then OFF for 350ms during

the duration of the event.

Slow Fade Strobe will increase in brightness from 0 to the specified brightness and back to 0 over

the course of about 3.5 seconds during the duration of the event.

Fast Fade Strobe will increase in brightness from 0 to the specified brightness and back to 0 over

the course of about 1.5 seconds during the duration of the event.

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

Table 2-12. SIP Configuration Parameters (continued)

Web Page Item Description

Slow Blink Strobe will blink ON at the specified brightness for one second then OFF for one

second during the duration of the event.

Fast Blink Strobe will blink ON at the specified brightness then OFF five times per second during

the duration of the event.

Color Select desired color (only one may be chosen).

Brightness How bright the strobe will blink when there is a SIP Ring. This is the maximum

brightness for “fade” type scenes.

Red The red LED value for SIP Ring.

Green The green LED value for SIP Ring.

Blue The blue LED value for SIP Ring.

Use this button to preview the strobe flashing behavior for the SIP Ring Strobe

Settings.

SIP Call Strobe Settings The following strobe settings will only appear if a CyberData Strobe product is

connected to your device. If a CyberData Strobe product is not connected to your device, you will not see the strobe settings.

Blink Strobe during Call When selected, the Strobe will blink a scene during a call.

Scene Select desired scene (only one may be chosen).

ADA Compliant Strobe will blink ON at the specified brightness for 150ms then OFF for 350ms during

the duration of the event.

Slow Fade Strobe will increase in brightness from 0 to the specified brightness and back to 0 over

the course of about 3.5 seconds during the duration of the event.

Fast Fade Strobe will increase in brightness from 0 to the specified brightness and back to 0 over

the course of about 1.5 seconds during the duration of the event.

Slow Blink Strobe will blink ON at the specified brightness for one second then OFF for one

second during the duration of the event.

Fast Blink Strobe will blink ON at the specified brightness then OFF five times per second during

the duration of the event.

Color Select desired color (only one may be chosen).

Brightness How bright the strobe will blink when there is a SIP Call. This is the maximum

brightness for “fade” type scenes.

Red The red LED value for SIP Call.

Green The green LED value for SIP Call.

Blue The blue LED value for SIP Call.

Use this button to preview the strobe flashing behavior for the SIP Call Strobe

Settings.

MWI Strobe Settings The following strobe settings will only appear if you are using the Strobe Kit. If

you are not using the Strobe Kit, you will not see the strobe settings.

Blink Strobe on MWI When selected, the strobe will blink a scene when a voicemail is waiting for its

extension.

Scene Select desired scene (only one may be chosen).

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

Table 2-12. SIP Configuration Parameters (continued)

Web Page Item Description

ADA Compliant Strobe will blink ON at the specified brightness for 150ms then OFF for 350ms during

the duration of the event.

Slow Fade Strobe will increase in brightness from 0 to the specified brightness and back to 0 over

the course of about 3.5 seconds during the duration of the event.

Fast Fade Strobe will increase in brightness from 0 to the specified brightness and back to 0 over

the course of about 1.5 seconds during the duration of the event.

Slow Blink Strobe will blink ON at the specified brightness for one second then OFF for one

second during the duration of the event.

Fast Blink Strobe will blink ON at the specified brightness then OFF five times per second during

the duration of the event.

MWI Call Color Select desired color (only one may be chosen).

Brightness How bright the strobe will blink when there is a message waiting. This is the maximum

brightness for “fade” type scenes.

Red The red LED value for MWI.

Green The green LED value for MWI.

Blue The blue LED value for MWI.

Use this button to preview the strobe flashing behavior for the MWI Strobe Settings.

Nightringer Settings

Enable Nightringer When Nightringer is enabled, the device will attempt to register a second extension

with the SIP server. Any calls made to this extension will play a ringtone (corresponds to Night Ring on the Audiofiles page). By design, it is not possible to answer a call to the Nightringer extension.

SIP Server Enter the SIP server address as an IPv4 address in dotted decimal notation or a fully

qualified domain name. This parameter also becomes the host portion of the SIP-URI for the device's Nightringer extension on the SIP server. This field can accept entries of up to 255 characters in length.

Remote SIP Port The Remote SIP Port is the port number the device will use as the destination port

when sending SIP messages for the Nightringer extension. The default Remote SIP Port is 5060. The supported range is 0-65536. Enter up to 5 digits.

Local SIP Port The Local SIP Port is the port number the device will use to receive SIP messages for

the Nightringer extension. This value cannot be the same as the Local SIP Port for the primary extension. The default Local SIP Port is 5061. The supported range is 0-

65536. Enter up to 5 digits.

Outbound Proxy Enter the Outbound Proxy address as an IPv4 address in dotted decimal notation or a

fully qualified domain name (FQDN). When an IP address is configured, the device will send all SIP messages to this IP address for the Nightringer extension. When an FQDN is configured, the device will run DNS NAPTR, SRV, and A queries on the FQDN to resolve an IP address to which it will send all SIP messages for the Nightringer extension. This field can accept entries of up to 255 characters in length.

Outbound Proxy Port The Outbound Proxy Port is port number used as the destination port when sending

SIP messages to the outbound proxy for the Nightringer extension. A value of 0 will default to 5060. The supported range is 0-65536. Enter up to 5 digits.

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

Table 2-12. SIP Configuration Parameters (continued)

Web Page Item Description

User ID Specify the SIP User ID for the SIP server. This parameter becomes the user portion

of the SIP-URI for the device's Nightringer extension. Enter up to 64 alphanumeric characters.

Authenticate ID Specify the Authenticate ID for the SIP Server. This parameter is required for SIP

registration authentication. Enter up to 64 alphanumeric characters.

Authenticate Password Specify the Authenticate Password for the SIP Server. This parameter is required for

SIP registration authentication. Enter up to 64 alphanumeric characters.

Re-registration Interval (in seconds) The SIP Re-registration Interval (in seconds) is the SIP Registration lease time, also

known as the expiry. The supported range is 30-3600 seconds. Enter up to 4 digits.

Nightringer Strobe Settings The following strobe settings will only appear if you are using the Strobe Kit. If

you are not using the Strobe Kit, you will not see the strobe settings.

Blink Strobe on Nightring When selected, the Strobe will blink a scene when the Nightringer is ringing.

Scene Select desired scene (only one may be chosen).

ADA Compliant Strobe will blink ON at the specified brightness for 150ms then OFF for 350ms during

the duration of the event.

Slow Fade Strobe will increase in brightness from 0 to the specified brightness and back to 0 over

the course of about 3.5 seconds during the duration of the event.

Fast Fade Strobe will increase in brightness from 0 to the specified brightness and back to 0 over

the course of about 1.5 seconds during the duration of the event.

Slow Blink Strobe will blink ON at the specified brightness for one second then OFF for one

second during the duration of the event.

Fast Blink Strobe will blink ON at the specified brightness then OFF five times per second during

the duration of the event.

Color Select desired color (only one may be chosen).

Brightness How bright the strobe will blink when the Nightringer is ringing. This is the maximum

brightness for “fade” type scenes.

Red The red LED value for Nightringer.

Green The green LED value for Nightringer.

Blue The blue LED value for Nightringer.

Use this button to preview the strobe flashing behavior for the Nightringer Strobe

Settings.

RTP Settings

RTP Port (even) Specify the port number used for the RTP stream after establishing a SIP call. This

port number must be an even number and defaults to 10500. The supported range is 0-65536. Enter up to 5 digits.

Jitter Buffer Specify the size of the jitter buffer (in milliseconds) used for SIP calls. Valid values are

50-1000.

Call Disconnection

Terminate Call After Delay Automatically terminate an active call after a given delay in seconds. A value of 0 will

disable this function. Enter up to 8 digits.

Codec Selection

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

Table 2-12. SIP Configuration Parameters (continued)

Web Page Item Description

Force Selected Codec When configured, this option will allow you to force the device to negotiate for the

selected codec. Otherwise, the device will perform codec negotiation using the default list of supported codecs.

Codec Select the desired codec (only one may be chosen).

Button Settings

Dial Out Extension Specify the extension the device will call when someone presses the Call button.

Enter up to 64 alphanumeric characters.

Note: For information about dial-out extension strings and DTMF tones, see Section

2.3.7.1, "Dial Out Extension Strings and DTMF Tones (using rfc2833)".

Extension ID A Caller identification string added to outbound calls. Enter up to 64 alphanumeric

characters.

Click the Save button to save your configuration settings.

Note: You need to reboot for changes to take effect.

Click on the Reboot button to reboot the system.

Click on the Toggle Help button to see a short description of some of the web page items. First click on the Toggle Help button, and you will see a question mark ( ) appear next to some of the web page items. Move the mouse pointer to hover over a question mark to see a short description of a specific web page item.

Note You must click on the Save button and then the Reboot button for the changes to take

effect.

Note For s

pecific server configurations, go to the following website address:

http://www.cyberdata.net/connecting-to-ip-pbx-servers/

2.3.7.1 Dial Out Extension Strings and DTMF Tones (using rfc2833)

On the SIP Configuration Page—Top, dial out extensions support the addition of comma delimited pauses and sending additional DTMF tones (using rfc2833). The first comma will pause three seconds aft seconds. A pause of one second will be sent after each numerical digit.

Extension String Resulting Action

302 Dial out extension 302 and establish a call

302,2 Dial out extension 302 and establish a call, wait 3 seconds then send the

er a call is first established with a remote device. Subsequent commas will pause for 2

Table 2-13. Examples of Dial-Out Extension Strings

DTMF tone '2'

302,25,,,4,,1 Dial out extension 302 and establish a call, wait 3 seconds then send the

DTMF tone '2', send out DTMF tone 5, wait 6 seconds, send out DTMF tone 4, wait 4 seconds, send out DTMF tone 1

Note The ma

Operations Guide 931191I CyberData Corporation

ximum number of total characters in the dial-out field is 64.

2.3.7.2 Point-to-Point Configuration

Device is set to NOT register with a SiP server

When the device is set to not register with a SIP server (see Figure 2-24), it is possible to set the device to dial out to a single endpoint.

In this case, the dial-out extension should be the IP address of the remote device. The device can also receive Point-to-Point calls. The delayed DTMF functionality is available in the Point-to-Point Mode.

Note Receiving point-to-point SiP calls may not work with all phones.

Figure 2-24. SIP Page Set to Point-to-Point Mode

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

2.3.7.3 Delayed DTMF

On the SIP Configuration page the dial out extension supports the addition of comma delimited pauses and sending additional DTMF tones (using rfc2833). The first comma will pause three seconds after a call is first established with a remote device. Subsequent commas will pause for 2 seconds. A pause of one second will be sent after each numerical digit.

Extension String Resulting Action

302 Dial out extension 302 and establish a call

302,2 Dial out extension 302 and establish a call, wait 3 seconds then send the

302,25,,,4,,1 Dial out extension 302 and establish a call, wait 3 seconds then send the

Installing the SIP Talk-Back Speaker

Device Configuration

Table 2-14. Examples of Dial-Out Extension Strings

DTMF tone '2'

DTMF tone '2', send out DTMF tone 5, wait 6 seconds, send out DTMF tone 4, wait 4 seconds, send out DTMF tone 1

Note The ma

ximum number of total characters in the dial-out field is 25.

Operations Guide 931191I CyberData Corporation

2.3.8 Configure the Multicast Parameters

The strobe settings will only appear if you are using the Strobe Kit. If you are not using the Strobe Kit, you will not see the strobe settings.

The Multicast Configuration page allows the device to join up to ten paging zones for receiving ulaw/alaw encoded RTP audio streams.

A paging zone can consist of one or many CyberData multicast group-enabled products. There is no limit to how many speakers can be in a given paging zone. Each multicast group is defined by a multicast address and port number.

Each multicast group is assigned a priority, allowing simultaneously arriving pages to be serviced based on importance. Multicast groups are compatible with IGMP through version 3. The device supports simultaneous SIP and Multicast.

1. Click on the Multicast menu button to open the Multicast page. See Figure 2-25.

Figure 2-25. Multicast Configuration Page

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

2. On the Multicast page, enter values for the parameters indicated in Ta bl e 2-15.

Note The question mark icon (

after the To

ggle Help button is pressed..

) in the following table shows which web page items will be defined

Table 2-15. Multicast Page Parameters

Web Page Item Description

Enable Multicast Operation Enables or disables multicast operation.

Blink Strobe on Multicast

When selected, the Strobe will blink a scene when a multicast is received.

Note: The strobe settings will only appear if you are using the Strobe Kit. If y

ou are not using the Strobe Kit, you will not see the strobe settings.

Priority Indicates the priority for the multicast group. Priority 9

is the highest (emergency streams). 0 is the lowest (background music). SIP calls are considered priority 4.5. See Section 2.3.8.1, "Assigning Priority" for more details.

Address Enter the multicast IP Address for this multicast group (15 character limit).

Por t Enter the port number for this multicast group (5 character limit [range can be from

000 to 65535]).

Note: The multicast ports have to be even values. The webpage will enforce this restriction.

Name Assign a descriptive name for this multicast group (25 character limit).

Buffer Device will buffer up to four minutes of audio and then play back the recording after

ulticast stream finishes or after the buffer is full.

the m

Beep When selected, the device will play a beep before multicast audio is sent.

Relay When selected, the device will activate a relay before multicast audio is sent.

Scene

ADA Compliant

Slow Fade

Fast Fade

Slow Blink

Fast Blink

Color

Brightness

Red

Green

Blue

Select desired scene (only one may be chosen).

Note: The strobe settings will only appear if you are using the Strobe Kit. If y

ou are not using the Strobe Kit, you will not see the strobe settings.

Strobe will blink ON at the specified brightness for 150ms then OFF for 350ms during the duration of the event.

Strobe will increase in brightness from 0 to the specified brightness and back to 0 over the course of about 3.5 seconds during the duration of the event.

Strobe will increase in brightness from 0 to the specified brightness and back to 0 over the course of about 1.5 seconds during the duration of the event.

Strobe will blink ON at the specified brightness for one second then OFF for one second during the duration of the event.

Strobe will blink ON at the specified brightness then OFF five times per second during the duration of the event.

Select desired color (only one may be chosen).

How bright the strobe will blink on a multicast page. This is the maximum brightness for “fade” type scenes.

The red LED value for Multicast.

The green LED value for Multicast.

The blue LED value for Multicast.

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

Table 2-15. Multicast Page Parameters (continued)

Web Page Item Description

Polycom Default Channel When a default Polycom channel/group number is selected, the device will

subscribe to the default channel for one-way group pages. Group Numbers 1-25 are supported. Or, select Disabled to disable this channel.

Polycom Priority Channel When a priority Polycom channel/group number is selected, the device will

subscribe to the priority channel for one-way group pages. Group Numbers 1-25 are supported. Or, select Disabled to disable this channel.

Polycom Emergency Channel When an emergency Polycom channel/group number is selected, the device will

sub

scribe to the default channel for one-way group pages. Group Numbers 1-25

are supported. Or, select Disabled to disable this channel.

Use this button to preview the strobe flashing behavior for the Multicast Strobe Settings.

Click the Save button to save your configuration settings.

Note: You need to reboot for changes to take effect.

Click on the Reboot button to reboot the system.

Note You must click on the Save button and then the Reboot button for the changes to take

effect.

2.3.8.1 Assigning Priority

The device will prioritize simultaneous audio streams according to their priority in the list.

If both SIP and Multicast is enabled, SIP audio streams are considered priority 4.5. SIP audio will interr

upt multicast streams with priority 0 through 4 and will be interrupted by multicast streams with

priority 5 through 9.

During priority 9 m

Note SIP calls

prioritized.

Ringtones and Nightringtones

Ringtones all play at the same priority level. This means that it is possible to have a nightring tone and a normal ringtone playing at the same time.

Click on the Toggle Help button to see a short description of some of the web page items. First click on the Toggl e H e l p button, and you will see a question mark ( ) appear next to some of the web page items. Move the mouse pointer to hover over a question mark to see a short description of a specific web page item.

ulticast streams, the volume is set to maximum.

, multicast streams, ring tones, ringback tones, and nightring tones are all

Operations Guide 931191I CyberData Corporation

2.3.9 Configure the Sensor Configuration Parameters

The door sensor (pins 5 and 6) on the header can be used to monitor a door's open or closed state. There is an option on the Sensor page to trigger on an open or short condition on these pins. The door sensor alarm will be activated when the Door Open Timeout parameter has been met.

The intrusion sensor is an optical sensor installed on the board and will be activated when the board is removed from the case.

Each sensor can trigger up to five different actions:

• Flash the LED until the sensor is deactivated (roughly 10 times/second)

• Activate the relay until the sensor is deactivated

• Loop an audio file out of the speaker until the sensor is deactivated

• Call an extension and establish two way audio

• Call an extension and play a pre-recorded audio file

Note Calling a preset extension can be set up as a point-to-point call, but currently can't send

delayed DTMF tones.

Installing the SIP Talk-Back Speaker

Device Configuration

1. Click Sensor menu button to open the Sensor page (Figure 2-26).

Operations Guide 931191I CyberData Corporation

Figure 2-26. Sensor Configuration Page

The strobe settings will only appear if you are using the Strobe Kit. If you are not using the Strobe Kit, you will not see the strobe settings.

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

2. On the Sensor page, enter values for the parameters indicated in Ta bl e 2-16.

Device Configuration

Note The question mark icon (

after the To

ggle Help button is pressed.

) in the following table shows which web page items will be defined

Table 2-16. Sensor Configuration Parameters

Web Page Item Description

Sensor Settings

Sensor Normally Closed Select the inactive state of the sensor. The sensor is also known

as the Sense Input on the device's terminal block. See the Operations Guide for more information.

Sensor Timeout (in seconds) The time (in seconds) the device will wait before it performs an

action when the on-board door sensor is activated. The action(s) performed are based on the configured Sensor Settings below. Enter up to 5 digits.

Activate Relay When selected, the device's on-board relay will be activated until

the on-board door sensor is deactivated.

Play Audio Locally When selected, the device will loop an audio file out of the

speaker until the door sensor is deactivated.

Make call to extension When selected, the device will call an extension when the on-

board door sensor is activated. Use the Dial Out Extension field below to specify the extension the device will call.

Dial Out Extension Specify the extension the device will call when the on-board door

sensor is activated. Enter up to 64 alphanumeric characters.

Dial Out ID An additional Caller identification string added to outbound calls.

Enter up to 64 alphanumeric characters.

Play recorded audio When selected, the device will call the Dial Out Extension and

play an audio file to the phone answering the SIP call (corresponds to Door Ajar on the Audiofiles page).

Repeat Sensor Message The number of times to repeat the audio message through the

local speaker or to the remote endpoint. A value of 0 will repeat forever. Enter a value from 0-65536.

Click the Test Sensor button to test the sensor.

Sensor Strobe Settings The following strobe settings will only appear if you are

using the Strobe Kit. If you are not using the Strobe Kit, you will not see the strobe settings.

Blink Strobe on Sensor When selected, the Strobe will blink a scene when the sensor is

triggered.

Scene Select desired scene (only one may be chosen).

ADA Compliant Strobe will blink ON at the specified brightness for 150ms then

OFF for 350ms during the duration of the event.

Slow Fade Strobe will increase in brightness from 0 to the specified

brightness and back to 0 over the course of about 3.5 seconds during the duration of the event.

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

Table 2-16. Sensor Configuration Parameters (continued)

Web Page Item Description

Fast Fade Strobe will increase in brightness from 0 to the specified

brightness and back to 0 over the course of about 1.5 seconds during the duration of the event.

Slow Blink Strobe will blink ON at the specified brightness for one second

then OFF for one second during the duration of the event.

Fast Blink Strobe will blink ON at the specified brightness then OFF five

times per second during the duration of the event.

Color Select desired color (only one may be chosen).

Brightness How bright the strobe will blink when the sensor is triggered. This

is the maximum brightness for “fade” type scenes.

Red The red LED value for Sensor.

Green The green LED value for Sensor.

Blue The blue LED value for Sensor.

Use this button to preview the strobe flashing behavior for the Sensor Strobe Settings.

Click the Save button to save your configuration settings.

Note: You need to reboot for changes to take effect.

Click on the Reboot button to reboot the system.

Click on the Toggle Help button to see a short description of some of the web page items. First click on the Toggle Help button, and you will see a question mark ( ) appear next to some of the web page items. Move the mouse pointer to hover over a question mark to see a short description of a specific web page item.

Note You must click on the Save button and then the Reboot button for the changes to take

effect.

Operations Guide 931191I CyberData Corporation

2.3.10 Configure the Audio Configuration Parameters

The Audiofiles page is used to add custom audio to the board. User uploaded audio will take precedence over the audio files shipped with the device.

1. Click on the Audiofiles menu button to open the Audiofiles page (Figure 2-27).

Figure 2-27. Audiofiles Page

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

Figure 2-28. Audiofiles Page

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

Figure 2-29. Audiofiles Page

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

2. On the Audiofiles page, enter values for the parameters indicated in Ta bl e 2-17.

Note The question mark icon (

after the To

ggle Help button is pressed.

) in the following table shows which web page items will be defined

Table 2-17. Audiofiles Page Parameters

Web Page Item Description

Available Space Shows the space available for the user to save custom audio files if they want to change the

message when the door or sensor is triggered.

Stored Messages

Stored Message 1 through 9 Stored Message 1 corresponds to the message played after pressing 1 on a phone keypad.

Stored Message 2 corresponds to the message played after pressing 2 on a phone keypad.

Stored Message 3 corresponds to the message played after pressing 3 on a phone keypad.

Stored Message 4 correspo

nds to the message played after pressing 4 on a phone keypad.

Stored Message 5 corresponds to the message played after pressing 5 on a phone keypad.

Stored Message 6 corresponds to the message played after pressing 6 on a phone keypad.

Stored Message 7 correspo

nds to the message played after pressing 7 on a phone keypad.

Stored Message 8 corresponds to the message played after pressing 8 on a phone keypad.

Stored Message 9 corresponds to the message played after pressing 9 on a phone keypad.

Audio Files

0-4 The name of the audio configuration option is the same as the spoken audio that plays on

the board (24 character limit).

'0' corresponds to the spoken word “zero.”

'1' corresponds to the spoken word “one.”

'2' corresponds to the spoken word “two.”

'3' corresponds to the spoken word “three.”

'4' corresponds to the spoken word “four.”

5-9 The name of the audio configuration option is the same as the spoken audio that plays on

the board (24 character limit).

'5' corresponds to the spoken word “five.”

'6' corresponds to the spoken word “six.”

'7' corresponds to the spoken word “seven.”

'8' corresponds to the spoken word “eight.”

'9' corresponds to the spoken word “nine.”

Dot Corresponds to the spoken word “dot.” (24 character limit)

Audio Test Corresponds to the message “This is

the CyberData IP speaker test message...” (24

character limit)

Enter Code Corresponds to the message “Enter Cod

Invalid Code Corresponds to the message “Invalid Co

e” (24 character limit).

de” (24 character limit).

Page Tone Corresponds to a simple tone used for beep on initialization and beep on page (24 character

limit).

Your IP Address is Corresponds to the message “Your IP address is...” (24 character limit).

Rebooting Corresponds to the spoken word “Re

Operations Guide 931191I CyberData Corporation

booting” (24 character limit).

Installing the SIP Talk-Back Speaker

Device Configuration

Table 2-17. Audiofiles Page Parameters (continued)

Web Page Item Description

Restoring Default Corresponds to the message “Restoring default” (24 character limit).

Ring Tone This is the tone that plays when set to ring when receiving a call (24 character limit).

Sensor Triggered Corresponds to the message “Sensor Triggered” (24 character limit).

Night Ring Specifies the ringtone for nightring. By default this parameter uses the same audio file that is

selected for the Ring Tone parameter.

Menu Audio Files Menu Audio Files are user-uploadable messages that create the audio menu played to the

caller.

Cancel Corresponds to the word "Cancel" used in the audio menu played to the caller. (24 character

limit).

Currently Playing Corresponds to the words "Currently Playing" used in the audio menu played to the caller.

(24 character limit).

Invalid Entry Corresponds to the words "Invalid Entry" used in the audio menu played to the caller. (24

character limit).

Page Corresponds to the word "Page" used in the audio menu played to the caller. (24 character

limit).

Play Stored Message Corresponds to the words "Play Stored Message" used in the audio menu played to the

caller. (24 character limit).

Pound (#) Corresponds to whatever word or phrase the user wishes to call the pound key in the audio

menu played to the caller (24 character limit).

Press Corresponds to the word "Press" used in the audio menu played to the caller. (24 character

limit).

Stored Message Corresponds to the words "Stored Message" used in the audio menu played to the caller.

(24 character limit).

Through Corresponds to the word "Through" used in the audio menu played to the caller. (24

character limit).

To Corresponds to the word "To" used in the audio menu played to the caller. (24 character

limit).

Click on the Browse button to navigate to and select an audio file.

The Play button will play that audio file.

The Delete button will delete any user uploaded audio and restore the stock audio file.

The Save button will download a new user audio file to the board once you've selected the file by using the Browse button. The Save button will delete any pre-existing user-uploaded audio files.

Operations Guide 931191I CyberData Corporation

2.3.10.1 User-created Audio Files

User created audio files should be saved in the following format:

RIFF (little-endian) data, WAVE audio, Microsoft PCM, 16 bit, mono 8000 Hz

You can use the free utility Audacity to convert audio files into this format. See Figure 2-30 through

Figure 2-32.

Figure 2-30. Audacity 1

Installing the SIP Talk-Back Speaker

Device Configuration

Figure 2-31. Audacity 2

Operations Guide 931191I CyberData Corporation

When you export an audio file with Audacity, save the output as:

WAV (Microsoft) signed 16 bit PCM

• WAV (Microsoft) signed 16 bit PCM.

Figure 2-32. WAV (Microsoft) signed 16 bit PCM

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

2.3.11 Configure the Events Parameters

The Events page specifies a remote server that can be used to receive HTTP POST events when actions take place on the board.

1. Click on the Events menu button to open the Events page (Figure 2-33).

Figure 2-33. Event Configuration Page

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

2. On the Events page, enter values for the parameters indicated in Ta bl e 2-18.

Device Configuration

Note The question mark icon (

after the To

ggle Help button is pressed.

) in the following table shows which web page items will be defined

Table 2-18. Events Configuration Parameters

Web Page Item Description

Enable Event Generation The device will send HTTP POST events to the specified remote

server and port number whenever a certain action takes place. Select an event type below to generate an HTTP POST event.

Events

Enable Button Events When selected, the device will report Call button presses.

Enable Call Start Events

Enable Call Terminated Events

Enable Relay Activated Events

Enable Relay Deactivated Events

Enable Night Ring Events

When selected, the device will report the start of a SIP call.

When selected, the device will report the end of a SIP call.

When selected, the device will report relay activation.

When selected, the device will report relay deactivation.

When selected, the device will report when it starts ringing upon an incoming SIP call to the Nightringer extension. As a reminder, the Nightringer extension always rings upon an incoming SIP call and it is not possible to alter this behavior.

Enable Power On Events When selected, the device will report when it boots.

Enable Multicast Start Events

When selected, the device will report when the device starts playing a multicast audio stream.

Enable Multicast Stop Events

When selected, the device will report when the device stops playing a multicast audio stream.

Enable Sensor Events

When selected, the device will report when the on-board sensor is activated.

Enable 60 Second Heartbeat Events

When enabled, the device will report a Heartbeat event every 60 seconds. SIP registration is not required to generate Heartbeat events.

Check All Click on Chec

Uncheck All

Click on Uncheck All to de-select all of the events on the page.

k All to select all of the events on the page.

Event Server

Server IP Address The IPv4 address of the event server in dotted decimal notation.

Server Port

Specify the event server port number. The supported range is 0-

65536. Enter up to 5 digits.

Server URL

Generally, the destination URL is the name of the application that receives the events and the string in the HTTP POST command. It can be a script used to parse and process the HTTP POST events. Enter up to 127 characters.

Click the Save button to save your configuration settings.

Note: Y

ou need to reboot for changes to take effect.

Click on the Reboot button to reboot the system.

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

Table 2-18. Events Configuration Parameters(continued)

Web Page Item Description

Click on the Toggle Help button to see a short description of some of the web page items. First click on the Toggle Help button, and you will see a question mark (

) appear next to some of the web page items. Move the mouse pointer to hover over a question mark to see a short description of a specific web page item.

Note You must click on the Save button and then the Reboot button for the changes to take

effect.

Operations Guide 931191I CyberData Corporation

2.3.11.1 Example Packets for Events

The server and port are used to point to the listening server and the 'Remote Event Server URL' is the destination URL (typically the script running on the remote server that's used to parse and process the POST events).

Note The XML is URL-encoded before transmission so the following examples are not completely

accurate.

Here are example packets for every event:

POST xmlparse_engine HTTP/1.1 Host: 10.0.3.79 User-Agent: CyberData/1.0.0 Content-Length: 197 Content-Type: application/x-www-form-urlencoded

<?xml version="1.0" encoding="ISO-8859-1"?> <cyberdata NAME='CyberData Device' MAC='0020f70015b6'> <event>POWERON</event> </cyberdata>

Installing the SIP Talk-Back Speaker

Device Configuration

POST xmlparse_engine HTTP/1.1 Host: 10.0.3.79 User-Agent: CyberData/1.0.0 Content-Length: 199 Content-Type: application/x-www-form-urlencoded

<?xml version="1.0" encoding="ISO-8859-1"?> <cyberdata NAME='CyberData Device' MAC='0020f70015b6'> <event>HEARTBEAT</event> </cyberdata>

POST xmlparse_engine HTTP/1.1 Host: 10.0.3.79 User-Agent: CyberData/1.0.0 Content-Length: 196 Content-Type: application/x-www-form-urlencoded

<?xml version="1.0" encoding="ISO-8859-1"?> <cyberdata NAME='CyberData Device' MAC='0020f70015b6'> <event>BUTTON</event> </cyberdata>

POST xmlparse_engine HTTP/1.1 Host: 10.0.3.79 User-Agent: CyberData/1.0.0 Content-Length: 201 Content-Type: application/x-www-form-urlencoded

<?xml version="1.0" encoding="ISO-8859-1"?> <cyberdata NAME='CyberData Device' MAC='0020f70015b6'> <event>CALL_ACTIVE</event> </cyberdata> POST xmlparse_engine HTTP/1.1 Host: 10.0.3.79

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

User-Agent: CyberData/1.0.0 Content-Length: 205 Content-Type: application/x-www-form-urlencoded

<?xml version="1.0" encoding="ISO-8859-1"?> <cyberdata NAME='CyberData Device' MAC='0020f70015b6'> <event>CALL_TERMINATED</event> </cyberdata>

POST xmlparse_engine HTTP/1.1 Host: 10.0.3.79 User-Agent: CyberData/1.0.0 Content-Length: 197 Content-Type: application/x-www-form-urlencoded

<?xml version="1.0" encoding="ISO-8859-1"?> <cyberdata NAME='CyberData Device' MAC='0020f70015b6'> <event>RINGING</event> </cyberdata>

POST xmlparse_engine HTTP/1.1 Host: 10.0.3.79 User-Agent: CyberData/1.0.0 Content-Length: 234 Content-Type: application/x-www-form-urlencoded

Device Configuration

<?xml version="1.0" encoding="ISO-8859-1"?> <cyberdata NAME='CyberData Device' MAC='0020f70015b6'> <event>MULTICAST_START</event> <index>8</index> </cyberdata>

POST xmlparse_engine HTTP/1.1 Host: 10.0.3.79 User-Agent: CyberData/1.0.0 Content-Length: 233 Content-Type: application/x-www-form-urlencoded

<?xml version="1.0" encoding="ISO-8859-1"?> <cyberdata NAME='CyberData Device' MAC='0020f70015b6'> <event>MULTICAST_STOP</event> <index>8</index> </cyberdata>

POST xmlparse_engine HTTP/1.1 Host: 10.0.3.79 User-Agent: CyberData/1.0.0 Content-Length: 234 Content-Type: application/x-www-form-urlencoded <?xml version="1.0" encoding="ISO-8859-1"?> <cyberdata NAME='CyberData Device' MAC='0020f70015b6'> <event>RELAY_ACTIVATED</event> </cyberdata> POST xmlparse_engine HTTP/1.1 Host: 10.0.3.79

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

User-Agent: CyberData/1.0.0 Content-Length: 234 Content-Type: application/x-www-form-urlencoded <?xml version="1.0" encoding="ISO-8859-1"?> <cyberdata NAME='CyberData Device' MAC='0020f70015b6'> <event>RELAY_DEACTIVATED</event> </cyberdata>

Device Configuration

Operations Guide 931191I CyberData Corporation

2.3.12 Configure the Autoprovisioning Parameters

Autoprovisioning can be used to automatically configure your device. The autoprovisioning file is an xml file with the device configuration. Values found in this file will override values stored in on-board memory.

Note By default, the device will try to set up its configuration with autoprovisioning.

1. Click the Autoprov menu button to open the Autoprovisioning page. See Figure 2-34.

Figure 2-34. Autoprovisioning Page

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

2. On the Autoprovisioning page, you may enter values for the parameters indicated in Tab l e 2-

19.

Note The question mark icon (

after the To

ggle Help button is pressed.

) in the following table shows which web page items will be defined

Table 2-19. Autoprovisioning Configuration Parameters

Web Page Item Description

Disable Autoprovisioning Prevent the device from automatically trying to download a

configuration file. See Section 2.3.12.1, "Autoprovisioning" for more information.

Autoprovisioning Server

Enter the IPv4 address of the provisioning server in dotted decimal notation.

Autoprovisioning Filename

The autoprovisioning filename is the configuration filename. The default autoprovisioning filename is in the format of <mac address>.xml.

Supported filename extensions are .txt, and .xml. The current filename is denoted by an asterisk at the bottom of the

Autoprovisioning Page. Enter up to 256 characters.

A file may have any name with an xml extension. If a file name is entered, the device will look for the specified file name, and only that file.

Use tftp

The device will use TFTP (instead of http) to download autoprovisioning files.

Username

The username used to authenticate with an autoprovisioning server. Leave this field blank to disable authentication.

Password

Autoprovisioning Autoupdate  (in minutes)

Autoprovision at time (HHMMSS)

Autoprovision when idle (in minutes > 10)

The password used to authenticate with an autoprovisioning server. Leave this field blank to disable authentication.

The reoccurring time (in minutes) the device will wait before checking for new autoprovisioning files. Enter up to 6 digits. A value of 0 will disable this option.

To use the auto update options, enable the Set Time

Note:

with NTP Server on boot setting on the Device Configuration Page page (see Tab l e 2-6).

The time of day the device will check for a new autoprovisioning file. The time must be 6 characters in length and in HHMMSS format. An empty value will disable this option.

To use the auto update options, enable the Set Time

Note:

with NTP Server on boot setting on the Device Configuration Page page (see Tab l e 2-6).

The idle time (in minutes greater than 10) after which the device will check for a new autoprovisioning file. Enter up to 6 digits. A value of 0 will disable this option.

To use the auto update options, enable the Set Time

Note:

with NTP Server on boot setting on the Device Configuration Page page (see Tab l e 2-6).

Click the Save button to save your configuration settings.

You need to reboot for changes to take effect.

Note:

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

Table 2-19. Autoprovisioning Configuration Parameters (continued)

Web Page Item Description

Click on the Reboot button to reboot the system.

Click on the Toggle Help button to see a short description of some of the web page items. First click on the Toggle Help button, and you will see a question mark ( some of the web page items. Move the mouse pointer to hover over a question mark to see a short description of a specific web page item.

Press the Download Template button to create an autoprovisioning file for the device. See Section 2.3.12.3,

"Download Template Button"

Autoprovisioning log The autoprovisioning log provides information about the latest

toprovisioning attempt (i.e. dhcp options and server

au accessed and files parsed or not found).

) appear next to

Note You must click on the Save button and then the Reboot button for the changes to take

effect.

2.3.12.1 Autoprovisioning

On boot, the device will look for an autoprovisioning server configured on the Autoprovisioning Page or specified as a DHCP option. When it finds a server, it will try to download the following (in order of p

reference):

1. The file configured on the autoprovisioning page.

2. A file named according to it's mac address (for example: 0020f7350058.xml).

3. The file 000000cd.xml

The file can be hosted using a standard web server (lik download over SSL. The file server can be an ipv4 address in dotted decimal notation or a fully qualified domain name.

By default, the device will get its autoprovisioning server from the DHCP options. See Section

2.3.12.2, "Sample dhcpd.conf" for an example of how to configure dhcpd to offer autoprovisioning

server addresses. If multiple options are set, the device will attempt to download autoprovisioning f

iles from every server.

The DHCP option determines the protocol used to download the autoprovisioning file. The device looks f

or DHCP options in the following order:

1. Option 43 - a FQDN or an IP address to an http server

2. Option 72 - an IP address to an http server

e apache, IIS, or nginx), and the device can

3. Option 150 - an IP address to a tftp server

4. Option 66 - an IP address to a tftp server or if the entry starts with 'http', a FQDN to a http server.

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

You can download an autoprovisioning template file from the Autoprovisioning Page using the Download Template button (see Ta bl e 2-19). This file contains every configuration option that can be set on the board.

Autoprovisioning files can contain the whole configuration or a subset of this file. The first autoprovisioning file can also contain links to other autoprovisioning files.

The <MiscSettings> section contains some examples of additional autoprovisioning files:

<MiscSettings> <DeviceName>CyberData Device</DeviceName>     </MiscSettings>

After downloading the first autoprovisioning file, the device will step through up to twenty additional <AutoprovFile> entries and try to download these files from the same server.

When the device finds a filename with the string [macaddress], it will replace this string with the mac address.

As an example, the user has configured option 43 on their DHCP server to “http://example.com,” and on their server, they have a file named 0020f7123456.xml (the same as the mac address of the device).

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

The file 0020f7123456.xml contains:

<?xml version="1.0" encoding="utf-8" ?> <specific>

<DeviceName>Newname</DeviceName> <AutoprovFile>common.xml</AutoprovFile> <AutoprovFile>sip_reg[macaddress].xml</AutoprovFile> <AutoprovFile>audio[macaddress]</AutoprovFile> <AutoprovFile>device.xml</AutoprovFile>

</MiscSettings>

</specific>

1. The device will first set it's name to 'Newname'.

2. It will try to download http://example.com/common.xml.

3. It will try to download http://example.com/sip_reg0020f7123456.xml.

4. It will try to download http://example.com/audio0020f7123456.

5. It will try to download http://example.com/device.xml.

The device is reconfigured every time it downloads a new file so if two files configure the same option the last one will be the one that is saved.

Checking for New Autoprovisioning Files after Boot

It is possible to autoprovision autoprovisioning values (for example, to disable autoprovisioning or to configure a time to check for new files).

The device will always check for an autoprovisioning files on boot but it can be configured to also check after a periodic delay, when idle, or at a specified time. When one of these options is set, the device will download its autoprovisioning files again, and if it finds any differences from the files it downloaded on boot, it will force a reboot and reconfigure.

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

The Autoprovisioning Filename

The autoprovisioning filename can contain a file, a file path, or a directory.

Table 2-20. Autoprovisioning File Name

Autoprovisioning Filename

config.xml

/path/to/config.xml

subdirectory/path/ 10.0.1.3 10.0.1.3/subdirectory/path/0020f7020002.xml

Autoprovisioning

File Downloaded

Server

10.0.1.3 10.0.1.3/config.xml

10.0.1.3 10.0.1.3/path/to/config.xml

TFTP options may not support subdirectories. If a directory is set in the filename field, firmware and

udio files will also be downloaded from this subdirectory.

If the filename ends with a forward slash “/,” the device will treat it as a subdirectory.

For example:

The autoprovisioning server is set to “https://www.example.com”

The autoprovisioning filename is set to “cyberdata/”

On boot, the device will try to download:

https://www.example.com/cyberdata/0020f7123456.xml

...and if this fails:

https://www.example.com/cyberdata/000000cd.xml

Audio files and firmware files will also add “cyberdata” to the URL before downloading.

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

Autoprovisioning Firmware Updates

<FirmwareFile>505-uImage-ceilingspeaker</FirmwareFile> <FirmwareServer>10.0.1.3</FirmwareServer> <OutdoorIntercom30>firmware_file_v9.3.0</OutdoorIntercom30> <OutdoorIntercom31>firmware_file_v10.3.0</OutdoorIntercom31> <CallButton31>firmware_file_v10.3.0</CallButton31>

</FirmwareSettings>

In the <FirmwareSettings> section, the <FirmwareServer> element can be used to specify a different server for hosting firmware files. When this element is not available, the device will try to download the file from the autoprovisioning server.

The device will use the filename to determine when to autoprovision firmware updates. The default configuration is blank, so the first time you set a value in your autoprovisioning file, it may force a firmware update even if the firmware version has not changed.

The <FirmwareFile> name can contain path elements (i.e. /path/to/firmware/10.3.0-uImage[device_file_name]).

The device also supports product strings for downloading firmware. If the <FirmwareFile> option is not set, the device will look for its particular product string for a firmware filename. In this way, a generic autoprovisioning file can specify unique firmware for a range of products.

The list of valid product strings:

<ProductString>CallButton31</ProductString>

<ProductString>EmergencyIntercom31</ProductString> <ProductString>EmergencyIntercom31SW</ProductString> <ProductString>IndoorIntercom31</ProductString> <ProductString>IndoorIntercom31SW</ProductString> <ProductString>IndoorKeypad31</ProductString> <ProductString>IndoorKeypad31SW</ProductString> <ProductString>OfficeRinger31</ProductString> <ProductString>OfficeRinger31SW</ProductString> <ProductString>OutdoorIntercom31</ProductString> <ProductString>OutdoorIntercom31SW</ProductString> <ProductString>OutdoorKeypad31</ProductString> <ProductString>OutdoorKeypad31SW</ProductString> <ProductString>Strobe31</ProductString> <ProductString>Strobe31SW</ProductString>

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

Autoprovisioning Example 1

Here's a simple example using four autoprovisioning files to configure two devices:

We boot up two devices with mac addresses 00:20:f7:02:00:01 and 00:20:f7:02:00:02 (Device1 and Device2).

The devices are set to use DHCP and that server provides an autoprovisioning server address with option 43. The address is “https://autoprovtest.server.net.” The files on this server are as follows:

000000cd.xml

<MiscSettings> <DeviceName>CyberData Autoprovisioned</DeviceName> <AutoprovFile>sip_common.xml</AutoprovFile> <AutoprovFile>sip_[macaddress].xml</AutoprovFile> </MiscSettings>

sip_common.xml

sip_0020f7020001.xml



sip_0020f7020002.xml

On boot, Device1 tries to fetch the file 0020f7023614.xml from “https://autoprovtest.server.net”. This file is not available, so device1 then tries to fetch the file 000000cd.xml. This file exists, and Device1 parses the three elements.

1. Device1 changes its device name to CyberData Autoprovisioned.

2. Device1 finds an AutoprovFile element containing the filename sip_common.xml. The device downloads sip_common.xml from “https://autoprovtest.server.net,” and imports this configuration, setting the sip server to 10.0.0.253 and the remote port to 5060.3.

3. Device1 finds another AutoprovFile element containing the filename sip_[macaddress].xml. The device replaces the [macaddress] with its own mac address value creating sip_0020f7020001.xml, downloads this file from “https://autoprovtest.server.net,” and imports this configuration. This sets the user ID to 198, the password to ext198, and the dialout extension to 204. Device1 is now finished with autoprovisioning.

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

Device2 goes through the same steps by setting its device name to CyberData Autoprovisioned, its SIP server to 10.0.0.253, and its port to 5060. When Device2 “sees” sip_[macaddress].xml, Device2 replaces it with its own mac address and downloads sip_0020f7020002.xml from “https://autoprovtest.server.net.” Device2 sets the SIP User ID to 500, the password to ext500, and the dialout extension to 555.

Autoprovisioning Example 2

Here is another example of setting up your autoprovisioning files:

We boot up two devices with mac addresses 00:20:f7:02:00:01 and 00:20:f7:02:00:02 (Device1 and Device2) and boot them on a network with a DHCP server configured with an autoprovisioning server at 10.0.1.3 on option 150. Our TFTP server has three files:

0020f7020001.xml

<MiscSettings> <AutoprovFile>common_settings.xml</AutoprovFile> </MiscSettings> <SIPSettings> <SIPUserID>198</SIPUserID> <SIPAuthPassword>ext198</SIPAuthPassword> <DialoutExtension0>204</DialoutExtension0> </SIPSettings>

0020f7020002.xml

<MiscSettings> <AutoprovFile>common_settings.xml</AutoprovFile> </MiscSettings> <SIPSettings> <SIPUserID>500</SIPUserID> <SIPAuthPassword>ext500</SIPAuthPassword> <DialoutExtension0>555</DialoutExtension0> </SIPSettings>



common_settings.xml

<MiscSettings> <DeviceName>CyberData Autoprovisioned</DeviceName> </MiscSettings> <SIPSettings> <SIPServer>10.0.0.253</SIPServer> <RemoteSIPPort>5060</RemoteSIPPort> </SIPSettings>

1. On boot, Device1 downloads 0020f7020001.xml from 10.0.1.3 and imports these values. The SIP User ID is 198, the password is ext198, and the dialout extension is 204.

2. Device1 then gets the filename common_settings.xml from the AutoprovFile element and downloads this file from the TFTP server at 10.0.1.3. and imports these settings. The device name is set to CyberData Autoprovisioned, the SIP server is set to 10.0.0.253, and the port is set to 5060.

Device2 does the same except it downloads 0020f7020002.xml on boot and imports these values instead. The Sip User ID is 500, password is ext500, and dialout extension is 555. Device2 then downloads the common_settings.xml file and imports those values. The device name is set to CyberData Autoprovisioned, the SIP server is set to 10.0.0.253, and the port is set to 5060.

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

Device Configuration

XML Files

Autoprovisioned Audio Files

XML files can contain <AutoprovFile> elements. If multiple DHCP options are specified, the device will try to download autoprovisioning files from each in turn. The device will only look for <AutoprovFile> elements in the first file downloaded from each server. You can specify up to 20 <AutoprovFile> elements in the first autoprovisioning file.

There are numerous ways to change an element of the configuration(xml) file. Using sip ext as an example, the extension can be changed:

Within the device-specific xml, i.e. [macaddress].xml, via the AutoprovFile element:<SIPSettings>/<SIPExt>

From the device specific xml, a pointer to a sip_common file

From the device specific xml, a pointer to the device specific sip_[macaddress].xml

From the common file, a pointer to sip_common.xml

From the common file, a pointer to the device specific (sip_[macaddress].xml)

Audio files are stored in non-volatile memory and an autoprovisioned audio file will only have to be downloaded once for each device. Loading many audio files to the device from the web page could cause it to appear unresponsive. If this happens, wait until the transfer is complete and then refresh the page.

The device uses the file name to determine when to download a new audio file. This means that if you used autoprovisioning to upload a file and then changed the contents of this file at the TFTP server, the device will not recognize that the file has changed (because the file name is the same).

Since audio files are stored in non-volatile memory, if autoprovisioning is disabled after they have been loaded to the board, the audio file settings will not change. You can force a change to the audio files on the board by clicking Restore Default on the Audio Configuration page or by changing the autoprovisioning file with “default” set as the file name.

Operations Guide 931191I CyberData Corporation

2.3.12.2 Sample dhcpd.conf

# # Sample configuration file for ISC dhcpd for Debian #

ddns-update-style none;

option domain-name "voiplab"; option domain-name-servers 10.0.0.252; option option-150 code 150 = ip-address; option ntp-servers north-america.pool.ntp.org; option space VendorInfo; option VendorInfo.text code 10 = { text }; authoritative; log-facility local7;

subnet 10.0.0.0 netmask 255.0.0.0 { max-lease-time 3600; default-lease-time 3600;

option routers 10.0.0.1; option subnet-mask 255.0.0.0;

option domain-name "voiplab"; option domain-name-servers 10.0.0.252;

Installing the SIP Talk-Back Speaker

Device Configuration

option time-offset -8; # Pacific Standard Time

# option www-server 99.99.99.99; # OPTION 72

# option tftp-server-name "10.0.1.52"; # OPTION 66 # option tftp-server-name "http://test.cyberdata.net"; # OPTION 66

# option option-150 10.0.0.252; # OPTION 150

# These two lines are needed for option 43 # vendor-option-space VendorInfo; # OPTION 43 # option VendorInfo.text "http://test.cyberdata.net"; # OPTION 43

range 10.10.0.1 10.10.2.1; }

Operations Guide 931191I CyberData Corporation

2.3.12.3 Download Template Button

The Download Template button allows the user to generate, download, edit, and then store an autoprovisioning template on the server that serves the autoprovisioning files for devices.

To generate an autoprovisioning template directly from the device, complete the following steps:

1. On the Autoprovisioning page, click on the Download Template button.

2. You will see a window prompting you to save a configuration file (.xml) to a location on your computer (Figure 2-35). The configuration file is the basis for the default configuration settings for your unit).

3. Choose a location to save the configuration file and click on OK. See Figure 2-35.

Figure 2-35. Configuration File

Installing the SIP Talk-Back Speaker

Device Configuration

4. At this point, you can open and edit the autoprovisioning template to change the configuration settings in the template for the unit.

5. You can then upload the autoprovisioning file to a TFTP or HTTP server where the file can be loaded onto other devices.

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

GENERAL ALERT

Device Configuration

2.4 Upgrade the Firmware and Reboot the SIP Talk-Back Speaker

Caution

Equipment Hazard: Devices with a serial number that begins with 0981xxxxx can only run firmware versions 10.0.0 or later.

2.4.1 Downloading the Firmware

To download the firmware to your computer:

1. Download the latest firmware file from the Downloads tab at the following webpage:

http://www.cyberdata.net/voip/011397/

2. Unzip the firmware version file. This file may contain the following:

• Firmware file

• Release notes

3. Log in to the home page as instructed in Section 2.3.4, "Log in to the Configuration Home

Page".

Operations Guide 931191I CyberData Corporation

Installing the SIP Talk-Back Speaker

GENERAL ALERT

v11.6.9

Device Configuration

4. Click on the Firmware menu button to open the Firmware page. See Figure 2-36.

Caution

Equipment Hazard: CyberData strongly recommends that you first reboot the device before attempting to upgrade the firmware of the device. See Section 2.4.2,

"Reboot the Device".

Figure 2-36. Firmware Page

5. Click on the Br

owse button, and then navigate to the location of the firmware file.

6. Select the firmware file.

7. Click on the Upload b

Note Do not reboot the d

Note This starts the

utton.

evice after clicking on the Upload button.

upgrade process. Once the SIP Talk-Back Speaker has uploaded the file, the Uploading Firmware countdown page appears, indicating that the firmware is being written to flash. The SIP Talk-Back Speaker will automatically reboot when the upload is complete. When the countdown finishes, the Firmware page will refresh. The uploaded firmware filename should be displayed in the system configuration (indicating a successful upload and reboot).

8. Ta bl e 2-21 shows the web page items on the Fir

mware page.

Table 2-21. Firmware Parameters

Web Page Item Description

Current Firmware Version Shows the current firmware version.

Use the Br firmware file that you want to upload.

Click on the Upload b firmware and reboot the system.

owse button to navigate to the location of the

utton to automatically upload the selected

Operations Guide 931191I CyberData Corporation

2.4.2 Reboot the Device

v11.6.9

397100001

Reboot

To reboot a SIP Talk-Back Speaker, log in to the web page as instructed in Section 2.3.4, "Log in to

the Configuration Home Page".

1. Click on the Reboot button on the Home page (Figure 2-37). A normal restart will occur.

Figure 2-37. Home Page

Installing the SIP Talk-Back Speaker

Device Configuration

Operations Guide 931191I CyberData Corporation

CyberData 011397, 011398, 011395, 011396 Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Contents

1 Product Overview

1.1 How to Identify This Product

1.2 Installation

1.3 Product Features

1.4 Supported Protocols

1.5 Supported SIP Servers

1.6 Product Specifications

1.7 Optional Connections (J9 and J10)

1.8 Compliance

1.8.1 CE Testing

1.8.2 FCC Statement

1.9 SIP Talk-Back Speaker Modes

1.9.1 Optional 011185 Remote Call Button (sold separately)

1.9.2 Normal Mode

1.9.3 Monitor Mode

2 Installing the SIP Talk-Back Speaker

2.1 Parts List

2.2 Device Configuration

2.2.1 Connect Power to the Speaker

2.2.1.1 SIP Talk-Back Speaker to a 802.3af Compliant PoE Switch

2.2.1.2 SIP Talk-Back Speaker (with PoE Injector) to a 802.3af Compliant PoE Switch

2.2.1.3 Running the SIP Talk-Back Speaker with Auxiliary Power

2.2.2 Installation Options

2.2.2.1 Connecting the Auxiliary RGB Strobe to the SIP SPeaker

2.2.2.2 Connecting the SIP RGB Strobe to the SIP SPeaker

2.2.2.3 Running the SIP Talk-Back Speaker with a Remote Call Button

2.2.2.4 SIP Talk-Back Speaker with an External Device

2.2.2.5 SIP Talk-Back Speaker with Auxiliary Speaker Connection

2.2.2.6 SIP Talk-Back Speaker with Line Out

2.2.3 Confirm that the Speaker is Operational and Linked to the Network

2.2.3.1 Status LED

2.2.3.2 Link LED

2.2.4 Confirm the IP Address and Test the Audio

2.2.4.1 Reset Test Function Management (RTFM) Button

2.2.5 Adjust the Volume

2.2.6 How to Set the Factory Default Settings

2.2.6.1 RTFM Button

2.3.1 Factory Default Settings

2.3.2 SIP Talk-Back Speaker Web Page Navigation

2.3.3 Using the Toggle Help Button

2.3.4 Log in to the Configuration Home Page

2.3.5 Configure the Device

2.3.5.1 Time Zone Strings

Time Zone String Examples

Time Zone Identifier

World GMT Table

2.3.6 Configure the Network Parameters

2.3.7 Configure the SIP (Session Initiation Protocol) Parameters

2.3.7.1 Dial Out Extension Strings and DTMF Tones (using rfc2833)

2.3.7.2 Point-to-Point Configuration

2.3.7.3 Delayed DTMF

2.3.8 Configure the Multicast Parameters

2.3.8.1 Assigning Priority

Ringtones and Nightringtones

2.3.9 Configure the Sensor Configuration Parameters

2.3.10 Configure the Audio Configuration Parameters

2.3.10.1 User-created Audio Files

2.3.11 Configure the Events Parameters

2.3.11.1 Example Packets for Events

2.3.12 Configure the Autoprovisioning Parameters

2.3.12.1 Autoprovisioning

Checking for New Autoprovisioning Files after Boot

The Autoprovisioning Filename

Autoprovisioning Firmware Updates

Autoprovisioning Example 1

Autoprovisioning Example 2

XML Files

2.3.12.2 Sample dhcpd.conf

2.3.12.3 Download Template Button

2.4.1 Downloading the Firmware

2.4.2 Reboot the Device