Page 1
OPERATING
INSTRUCTIONS
&
PARTS
LIST
4~"(110m/m)ROUND
Electric Power : 180W
Cutting Capacity: 32mm
Net Weight : 3.5kgs
KNIFE CUTTER
* Before Use Read this instructions manul
& Save This instruction manual.
Page 2
~
73
~
~
Cll
>
Cll
Cll
tEl
'en,
1~/
1
61
,4
5
~~
/)
i'~l)
3
3~
32~Q
•
!;"'·
9
I
....
38
~
~-=-=
I
1ffi;Y'J
,~,
I
·~,
L~.J
I
67
'
.
65__11
14 72
I
I I
~p
~
71
74 75
g·)~
~
t-'
>
n
n
tEl
Cll
Cll
0
:::a
........
tEl
Cll
==
Page 3
.·
PART NO.
1
2
3 Shaft
4
PARTS
NAME
Adjusting Nut For Blade
Spring
For
Gear
Screw For Finger Guard
5 Finger Guard
6 Grease Cup
7
8
9
10-1
11
12
13
14
15
16
17
18
Cap For Grease Cup
Gear
Box
Screw
Worm Gear
Guide Plate
Gear
Box Fixed Base
Screw
Sharpening Stone
Lock Nut For Stone
Snap Ring (E3) 54
Spring
Screw
19 Sharpening Stone Bracket
20
21
Spring
Push Knob For Stone
22 Screw
23
24
25
Oil Felt
Counter Blade
Worm Gear Washer
26 Worm Gear
27
28
29
30
31
Blade
Lock Cover For Blade
Bearing 67
Screw For Blade
Bearing
32 Cap For Bearing
33
Oil Felt Tube
34 Rollers
35
Roller Shaft
36 Roller Shaft Fixed
37 Screw
1---
38 Rollers
r----3'9
L
Roller Shaft
Plate
PART NO. PARTS
40
41
Base Plate
Screw
NAME
42 Retaining Ring
43
Front Cover
44 Snap Ring
45
Wave Washer
46 Bearing
47-1 Rotor
48-1
Stator
49 Cap For Carbon Brush
50-1 Carbon Brush With Spring
51
51-1
52
53
Motor Cover
Carbon Brush Fixed Base
Snap Ring (E6)
Bearing
End Cover
55 Cap For Bearing
56 Screw
57 Screw
58 Screw
59 Handle Fixed Base
60 Handle
61
Nut For Switch
62 Switch
63
Nut For Switch
64 Screw
65
66
Screw
Screw
Plug
68
69
70
71
72
~03
x04
*75
76
Wave Washer
Motor Cover
Screw For Worm Gear
Code Complete with Earth
Grease
Capacitor
Capacitor
Inductor
Carbon Brush Fixed Base
* CE MODELS ONLY
Page 4
OPERATING
INSTRUCTIONS,
MAINTENANCE
&
SAFTY
Cutters are precision tools, made by
master craftsmen.
In
order to maintain this precision and the
adjustments which are
operation of your cutter, it is important to
conscientiously
1.1n
General
Handle cutter with great care. Do not drop it or
handle it roughly as this will change its
adjustments and may cause serious damage
to the mechanism.
follow these instructions.
essential to satisfactory
2.Prior to Starting the Cutting Operation
Firstly set the "ON/OFF" switch to the
position, connect the female plug of the
electric cord with the machine terminal and
then tighten the screw
Now connect the male plug of the electric cord
to the
cutting operation remove any
the
electrical outler. Prior to starting the
path
of
the base pia
on
the female plug.
obstacles from
e.
"off'
3.Cutting Operation
Do not force cutter through material. By
nature of their texture and because of the
properties of their fibers, not
be cut with the same speed or ease.
cutting will readily let you find the best speed
at which the machine is
through the
material.
all materials can
Trial
to
be advanced
4.Sharpening The Blade
4-1
Connect the plug of the electric cord to the
power
supply.
4-2 Push the switch to start the machine
4-3 Pressing the Push Knob (#21) down for a
few seconds
lightly touches and grinds the blade for
several times.
so
that the sharpening stone
6.How to replace carbon brush
1.While the machine
the two screw (#57) and
upward .
2.Remove the screwed cap (#49) over the
carbon brush and
(#50-1)
3.Put the cover (#54) back into its
position and tighten the screw.
4.Check right and
time
to
time and always replace both right
and
left carbon brushes when worn out.
is
unplugged. remove
pull the cover (#54)
replace the carbon brush
original
left carbon brushes from
?.Lubrication and Maintenance
1.Turn the grease cup (#7) clockwise a little
bit to inject the grease into the gear box.
2.Make sure
machine to the grease cup (#6) when the
grease cup is screwed down to the bottom
3.Aiways keep the machine
from remnants.
to
add grease supplied with the
clean and free
8.Maintenance and Inspection
8-1
Keep machine clean by removing all
accumulations
from around the knife
from behind it any
matter.
In
addition, add grease to the grease cup
8-2
monthly using the special grease that is
supplied with the machine.
8-3 From time to time, check the right and
carbon
necessary.
8-4
It is recommended that the machine be
turned off when not
8-5 Never put your hands
operating.
while
8-6 Before doing any work
sure to disconnect the machine from the
electrical outlet.
of
brushes
lint, thread and cuttings
itself to clean away
accumulated foreign
and
replace
in
use.
in
front
of
the blade
on
the machine, be
left
when
S.How
To
Replace Blade
5-1
Make
disconnected from the power source.
5-2 Turn the screw for finger guard (#4) and
remove the finger guard (#5)
5-3 Remove the
it
(#61
5-4 Remove the
dust or dirt from machine.
Replace the blade.
5-5
sure
the
electric
blade lock nut (#1) by turning
left, Take off Spring (#2), SCREW
,28,29,30)
blade (#27) and clean any
cord
is
--
03-2-30X 1 000
-
Loading...