Page 1
Magic™ Zone Bluetooth Command Remote
We thank you for purchasing the Custom Dynamics® Magic™ Zone
Command Remote. Our products utilize the latest technology and
high quality components to ensure you the most reliable service.
We offer one of the best warranty programs in the industry and we
back our products with excellent customer support, if you have
Everything to Light Up Your Ride®
Part Number: MAGICZONE-BT
Package Contents:
- Bluetooth Remote Module with inline fuse (1)
- Remote Key Fob (2)
Optional (Sold Separately):
CG01 Cage Clamps (4) for wire connection (included w/ CD lighting kits)
Winter Kill Switch (1) to kill power to remote during storage
questions before or during installation of this product please call
Custom Dynamics® at 1(800) 382-1388.
Installation Instructions
ATTENTION
The Magic™ Zone Command Remote has 6 wires that connect to the
battery and to the LED wiring. Please see the Diagram on page 2 to
correctly wire the remote module with your choice of LED lighting.
Installation Tips
1. Follow the wiring instructions on page 2 for wiring the LED’s to
the harness. Note: there are 2 red wires, the wire with the Fuse
goes to the battery.
2. Disconnect the Negative [ - ] battery cable from the battery
before beginning wiring to avoid electrical shorts.
3. Pick a location to run all of the wires from the LED’s and make
your connections. The most common location is under the seat
so to have easy access to the battery. Install the Magic™
Zone Command Remote in this area, paying attention so that
the module will not get crushed or in direct contact with water
and the wires will not get pinched, cut or frayed when the seat
is reinstalled.
4. Decide which LED’s will be on which zone, then group the
wires by zone 1, 2 and 3.
5. The output wire for any unused zone should be capped off to
prevent shorting.
6. For a clean, reliable install, use terminal blocks or Cage
Clamps® to group your wires.
7. Test function of the remote before riding.
8. If system will not turn on, check the inline fuse on the red wire,
then check the connections to the battery.
9. If system will not turn on, verify that the Red light on the key fob
is coming on. If it is not, or Red light is dim or is flickering, batteries are weak. Replace with fresh batteries and try again.
Please read all Information below before Installation
Caution: Before beginning installation, disconnect the negative
battery cable from the battery to prevent damage to the LEDs or
remote during installation. Damage to either as a result of direct
shorting is not covered under warranty.
Important: This unit is rated for a 7.5 amp load. Never use a fuse
greater than 7.5 amps in the in-line fuse holder, using a larger fuse
or bypassing the fuse will void warranty.
Note: This guide assumes user has properly installed the LED lighting products that are to be used in conjunction with this Remote.
Custom Dynamics is not responsible for procedures and instructions for installing LED products from other manufacturers.
Note: Zone Command Module™ App is Compatible with iPhone 4S
and newer equipped with Bluetooth 4.0 and with Android phones
versions 4.3 and newer with Bluetooth 4.0. Zone Command Module™ apps are available for download from the following sources:
- Google Play: https://play.google.com/store/apps
- iTunes: https://itunes.apple.com/
Keyword Search: Custom Dynamics or CCM-5BTS
Important: Module should be secured after installation in an area
away from heat, water and any moving parts. We recommend the
use of tie wraps (sold separately) to secure the module and wires to
prevent them from getting cut, frayed, or pinched. Custom Dynamics is not liable for damage as a result of improperly securing or
failing to secure the remote or the wiring.
Note: The functions available from the provided key fobs vary from
the functions available in the Bluetooth controller. Please read instructions completely before operating.
Operational Note: During the Dim Slider function, dropping to 30%
or lower while in breathe/strobe or zone transition modes will decrease the voltage cycle significantly, which may cause subtle variances in the zone transition speed or strobe/breathe speed. This is
normal operation of the Remote.
Questions? Call us at: 1 (800) 382-1388 M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST
05-2016SM
Page 2
Installation Instructions - Page 2
Wiring The Remote
For joining large quantities of wires, we recommend using cage clamp connectors, (included with most Custom Dynamics LED accent lighting
Kits). The cage clamps offer easy connection of the LEDs to the Magic™ Zone Remote. Strip back enough insulation on the wires and terminate as follows:
1. RED wire with Fuse - Connect to the [ + ] Positive terminal of 12 volt battery or power source.
2. BLACK wire - Connect to the [ - ] Negative terminal of 12 volt battery or power source.
3. WHITE wire - Positive current connection point: Connect to the positive [ + ] wires from the LEDs in all 3 zones.
4. RED wire - Zone 1 Connection point: the negative [ - ] wires from the LEDs from zone 1.
5. GREEN wire - Zone 2 Connection point: the negative [ - ] wires from the LEDs from zone 2.
6. BLUE wire - Zone 3 Connection point: the negative [ - ]wires from the LEDs from zone 3.
7. Once wiring is completed, clean up installation and secure the module. Make sure wiring is neat and will not be pinched, frayed or cut,
when the seat is installed.
8. Re-connect the negative battery terminal, then use the Key Fob to test the LEDs. See page 3 for Key Fob features.
Magic™ Zone-BT Wiring Diagram
Positive [ + ] Wires
From all LED’s
12V Battery
We recommend
Cage Clamps®
LED
Zone 1 = Negative [ - ]
wires from LEDs
Fuse
LED
Zone 2 = Negative [ - ]
wires from LEDs
Blue
Green
Red
White
Red
Black
LED
Zone 3 = Negative [ - ]
wires from LEDs
Magic™ Zone 4-BT
Optional Kill Switch
(Sold Separately)
Questions? Call us at: 1 (800) 382-1388 M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST
05-2016SM
Page 3
Installation Instructions - Page 3
Magic™ Zone BT Key Fob Features:
Button [1] - On Function/Select Zone
- Press once to turn zone 1 lights on.
- Press repeatedly to cycle through the zone combinations
(Allows single zone play or combinations)
Enter 2 Hour Timer Mode:
- Select your desired program settings
- Then Press button [1] down and hold:
The lights will blink white quickly then return to their previous function for 2 hours. At the end of the time limit, the lights will shut off
automatically. Do not change program or touch any buttons as this
will cancel the timer. Time cannot be adjusted. To turn timer function off, hit any button on the key fob and or turn the lights off.
Note: The use of the App controller gives you more time duration
setting options, see page 6 for details.
Button [2] - Auto Cycle with 3 Speeds
- Press to turn lights on, cycles through zones automatically
- First program is speed 1 (slow)
- Press again for speed 2 (medium)
- Press again for speed 3 (fast)
Button [3] - Strobe/Breathing Functions
(After button [1] or [2] is pressed first to turn lights on preset colors)
Press repeatedly to cycle through:
- 3 Strobe effects patterns
- 3 Breathing effect speeds
Button [4] - Off /Memory
During Auto Cycle:
- Press to pause and save on desired combination of zones
- Press again to turn off the lights
- Press again to turn lights back on and resume saved cycle
During Manual zones and “Strobe” or “Breathing” effects:
- Press once to save function and turn lights off
- Press again to turn on and resume zone or effects.
Ability to Auto Cycle and Strobe/breathe at the same time:
- Press button [2] 1 to 3 times to select auto cycle speed
- Then Press button [3] 1 to 3 times to select strobe/breathe
Button [1]
Button [2]
Receiver
Power: 12V/7.5A Fused
Transmitter/Key Fob:
Distance: Up to 50 Meters (clear line of sight)
Antenna: Internal
Power: 12V/10MA
Batteries: (2) CR2016 Coin Cell
Bluetooth Module:
Distance: Up to 50 Meters (clear Line of sight)
Antenna: Internal
Power: 12V
MAGICZONE-BT Features:
- Built-in Short Circuit Protection
- Memory Save
- Zone configuration
- Timer Function
- 3 Year Warranty
Note: Never use a fuse greater than
7.5 amps in the in-line fuse holder,
using a larger fuse will void warranty.
Button [3]
Button [4]
Everything to Light Up Your Ride®
Questions? Call us at: 1 (800) 382-1388 M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST
Custom Dynamics® is proud to offer a 3 year
warranty on your new remote. Contact us for
details.
05-2016SM
Page 4
Installation Instructions - Page 4
Bluetooth Zone Command Module
Get more control from your LED lights with the Magic™ Zone Command Module Blue tooth controller. This easy to use interface gives
you more color options and function combinations than just using the
key fob alone. See below for touch screen features.
Bluetooth Connect buttons: Scan, OK, &
Disconnect.
Slider Console: Control The intensity of
each of the 3 zones. Dim Controls
Brightness of all zones simultaneously.
Speed controls Strobe Flash and Zone
transition rates.
Compatible with iPhone 4S and newer equipped with Bluetooth
4.0 and with Android Phones Versions 4.3 and newer with
Bluetooth 4.0.
https://play.google.com/store/apps/details?
id=com.customdynamics
Apps for iPhone devices are available for download at: iTunes:
https://itunes.apple.com/
Keyword Search: Custom Dynamics or CCM-5BTS
Zone
Zone 1
Zone 2
Zone 3
Simple easy to use On & Off Buttons:
Color coded active status in Red.
Function Buttons: 6 Different Function
programs to choose from. See next
pages for explanation. Active function
highlighted in red.
Timer Function: Allows users to set lights
while parked and walk away. Timer durations are 30/60/120 minute intervals.
Everything to Light Up Your Ride®
Questions? Call us at: 1 (800) 382-1388 M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST
05-2016SM
Page 5
Installation Instructions - Page 5
Bluetooth Control Interface Sync Instructions-Android & iPhone
1. Make sure there is power going to the Remote Module.
2. Download the phone App for the appropriate operating system. Follow the prompts on device. Consult the Phone manufacturer
if unsure of this process. Keyword Search: Custom Dynamics or CCM-5BTS. ( Be sur e to dow nlo ad the corr ect “Zone
Remote” application)
Note: Remote should be synced through the app only, do not attempt to manually pair devices through the
device settings.
3. Open the App by touching the logo application icon, then sync the app to the receiver by tapping the “Scan” button. A list of Bluetooth devices should pop up. Find the device (labeled: CCM-5BT) in the list and tap to select. The application will confirm the connection. If the message reads connection failed or Disconnected, try the sync again. If remote does not show up in the list of devices or has trouble connecting, try rebooting the phone, then check to make sure Bluetooth function is enabled. Also, verify that power is getting to the remote module.
4. Turn on the Lights with the interface by tapping the “On” button. When activated, the button will change color from black to red.
The “F1” button will also change to red to indicate function 1 - Single zone control is activated.
1
Open the app located in the
“APPS” section of phone.
4
Tap the bar that says “Scan for
Devices”. (Android only - iPhone
users skip to #5 )
2 3
Tap on the Scan button at the top
left under logo.
5
A list of available devices will be
displayed. Tap the screen to select
the CCM-5BT.
System Prompt pops up asking to
select a device.
Confirmation of connection will be
displayed at the bottom.
6
Questions? Call us at: 1 (800) 382-1388 M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST
05-2016SM
Page 6
Installation Instructions - Page 6
Bluetooth Control Interface Functions
1. Scan: Tap the Scan button to Syn c th e Interface with t he
Zone
receiver via Bluetooth. Select the device in the list, tap to confirm. The Phone should give confirmation it is connected.
Note: If the app h as trouble connec tin g or do es not s how
CCM5-BT available in the list of devices, try rebooting the
phone, then double check that Bluetooth function is enabled.
2. OK: Tap to con firm Bluet oo th selectio n or wh en prom pted
by the Application.
3. Disconnect: When t his is tapped, c onnect ion between the
interface and the receiver is turned off. This should be performed when the system is turned off and the application will
not be used.
4. On: Tap anywher e in the b utton area and th e li ght ing sys-
tem comes on in the default F1 single color program. When
power is turned on, this button will be red.
5. Off: Tap anywher e in the b utton area an d the li ghtin g sys-
tem will turn off.
6. Zone 1 Slider: Cont rols the amoun t of po wer to the LEDs
assigned to zone 1. The Scale from left to right is 0-100 %.
Touch the Logo button within the slider area to adjust the intensity of the color. The Slider function is available in F1-F3 programs.
7. Zone 2 Slider: Cont rols the amoun t of po wer to the LEDs
assigned to zone 2. The Scale from left to right is 0-100 %.
Touch the Logo button within the slider area to adjust the intensity of the color. The Slider function is available in F1-F3 programs.
8. Zone 3 Slider: Cont rols the amoun t of po wer to the LEDs assigned t o zone 3. The Scale fro m left t o ri ght is 0-100 %. Touch
the Logo button within the slider area to adjust the intensity of the color. The Slider function is available in F1-F3 programs.
9. Dim Slider: Control s the amoun t of overall intensity o f th e LEDs wit hin all thr ee zon es simu ltaneou sly. The Sc ale from left
to right is 0-100 %. Touch the logo button within the slider area to adjust the overall brightness.
10. Speed Slider: Cont rol s the sp eed o f th e zon e transi tion as well as the speed of the stro be patter ns. The Scal e from l eft to
right is 0-100 %. Touch the logo button within the slider area to adjust the speed of strobe or zone transition.
11. F1—Function 1 (Zone control Mode): This i s the def ault pr ogr am w hen the inter fac e is turned on. Each Zo ne will come on
full intensity at 100%. Adjust the Zone sliders to adjust individual zone intensity.
-Dim slider allows all 3 zones to adjust intensity simultaneously.
-Speed slider does not control anything in the F1 mode.
12. F2—Function 2 (Strobe Mode): Adds a strobe to the Solid co lor zones sel ected in F1. Allow s each zon e sl ider to be adj ust-
ed during strobe operation.
-Dim slider also works to dim the brightness of all zones a one time.
-Speed slider works to slow the timing of the strobe function.
13. F3– Function 3 (Zone Breathe Mode): Adds a breathe function to the solid color zones selected in F1. Allows each zone slider to
be adjusted during breathe operation.
-Dim slider also work to dim the brightness of all zones at one time.
-Speed slider works to slow the timing of the breath function.
F3 Note: In F3 mode, with the speed slider at 100%, adjusting the zone sliders 1,2 or 3 will create a custom breath cycle. The different values in each zone, creates different breathe durations. The speed slider can then be used to change the pattern even further.
1
Zone 1
Zone 2
Zone 3
4 5
11
12 13 14 15
2 3
6
7
8
9
10
16
17
Questions? Call us at: 1 (800) 382-1388 M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST
05-2016SM
Page 7
Installation Instructions - Page 7
14. F4– Function 4 (Random Zone Change Mode): The program randomly changes between all 3 zones. Note: In F4, the zone profile
changes to a preset that is not adjustable, the zone sliders will not work in this mode.
-Dim slider allows the adjustment of overall light intensity of all zones together.
-Speed slider allows control of the speed of the changes.
15. F5—Function 5 (Single Pattern Strobe flash with Auto Zone cycle): Automatically cycles through program zone change cycle
with a single strobe flash. Note: In F5, the zone profile changes to a preset that is not adjustable, the zone sliders will not work in this
mode.
-Dim slider allows the adjustment of overall light intensity of all zones together.
-Speed slider allows control of the strobe and zone change speed at the same time.
16. F6—Function 6 (Auto Zone Cycle with Breathe function): Automatically cycles through program zone change cycle with a breathe
function. Note: In F6, the zone profile changes to a preset that is not adjustable, the zone sliders will not work in this mode.
-Dim slider allows the adjustment of overall light intensity of all zones together.
-Speed slider allows control of the breath and zone change speed at the same time.
17. Timer Mode: Tap on the dro p down arrow t o pull up t he timer op tions in minutes: 30/60/120, select a time an d w alk away.
When the timer mode is set, the lighting system will turn off after a preset amount of time. This is intended for showing off the vehicle
lighting in the parked position.
Note: The lights will blink white quickly then return to their previous function. At the end of the time limit, the lights will shut off automatically. Do not change program or touch any buttons as this will cancel the timer. Time cannot be adjusted once set. To turn timer
function off, hit any button on the interface or key fob or turn the lights off.
Note: If the Timer mode is set with the Key fob instead of the application, the key fob command is capable of a 2 hour time duration
only.
Questions? Call us at: 1 (800) 382-1388 M-TH 8:30AM-5:30PM / FR 9:30AM-5:30PM EST
Everything to Light Up Your Ride®
05-2016SM
Loading...