Custom Brackets Tilt Head AS User Manual

Tilt Head AS INSTRUCTIONS

Innovative Camera Supports

Lens lock knob

(press in and rotate

clockwise to tighten)

Tilt drag knob

(rotate clockwise

to tighten)

Tilt Head AS Features

Attaching lens plate to lens

Mounting holes

A lens may have 1/4” and / or 3/8” threaded
holes. (1) 3/8” and (2) 1/4” screws are
included with each lens plate. It is important
to use the correct size.

Attaching lens to Tilt Head AS

Lens plate

reference lines

Quick release

reference lines

Lens lock knob

Made in USA

Front View

Cleveland, Ohio 44143

32 Alpha Park

phone [phone]

Toll Free 800-530-2289

website: www.custombrackets.com

email: [e-mail]

Arca Swiss style
quick release

Tilt lock knob

(rotate counter-clockwise
to tighten)

Install screw(s) into lens plate at the labeled
ends. The screw(s) and / or plate may be
damaged if installed incorrectly. Some
lenses will require both screws be in one
slot.

The “D” screw has a fold out clip for
hand tightening. A screwdriver slot is also
included on the screw.

Do not insert any object as leverage into the
“D” clip as it will damage screw and void
warranty.

Attach lens with lens plate
by loosening lens lock knob
completely, then place lens
plate into quick release. Tighten
lens lock knob completely, then
loosen 1/2 turn. Slide lens
forward or backward to balance,
then retighten lens lock knob.

If you have a replacement lens
foot, use the same procedure
above.

Attaching the Tilt Head AS to a monopod

Attach the Tilt Head AS to the monopod’s ⅜”-16 mounting stud and tighten until rmly attached.

If you are using a monopod with a ¼”-20 mounting stud, you will need to purchase a ⅜” to ¼” reducer

* * * * *

bushing and install it in bottom of the Tilt Head’s base.

Caution

* * * * *

Indexing the quick release to accept a camera

Using the supplied allen wrench (3/16”), remove
screw from the top of the quick release, then lift
the quick release off the Tilt Head.

Align quick release far right image (Camera Setup)
and align pins using pin holes #1 & #2 (see below)
in top of the tilt head. Once in place, install screw
into the top of the quick release of the Tilt Head.
For Long Lens Setup, use pin holes #2 & #3.

Long Lens

Hole #2

Hole #1

Hole #3

Top view of Tilt Head

(quick release removed)

Tilt Head AS Features

The Tilt Head AS has many unique features. It is constructed from anodized aluminum for a lightweight

and scratch-resistent nish. The tilt head has separate lock and drag knobs for better control. All knobs
are captive to prevent loss. All of the fasteners are stainless steel to resist corrosion and black oxide for

appearance.

For a period of ve (5) years from date of purchase, Custom Brackets will repair or replace free of charge, any

defect in material or workmanship. Warranty does not cover repairs due to abuse, negligence, impact or any

modications made by the customer. Excessive force unscrewing knobs will void warranty. Warranty service is
available by returning the Tilt Head AS (shipping prepaid) to Custom Brackets. All returns must include a return
authorization (RA) number (contact Custom Brackets to obtain), letter explaining the problem, and a copy of

the sales receipt.

For a period of ve (5) years from date of purchase, Custom Brackets will repair or replace free of charge, any

defect in material or workmanship. Warranty does not cover repairs due to abuse, negligence, impact or any

modications made by the customer. Excessive force unscrewing knobs will void warranty. Limitation to the

warranty - after year one shipping charges are not covered. Warranty service is available by returning the Tilt

Head AS (shipping prepaid) to Custom Brackets. All returns must include a return authorization (RA) number
(email [e-mail] to obtain), letter explaining the problem, and a copy of the sales receipt.

International 5 Year Limited Warranty

USA 5 Year Warranty

Repair

Repair service is available by returning the Tilt Head AS (shipping prepaid) to Custom Brackets. All returns
must include a return authorization (RA) number (contact Custom Brackets to obtain), letter explaining the

problem, and a copy of the sales receipt. A repair cost will be issued and must be approved prior to any
repairs. Shipping charges are the responsibility of the customer.

Maintenance

The Tilt Head AS is designed completely maintenance-free.

Setup

Camera

Setup