Custom Brackets Pan-Tilt Head AS User Manual

Pan-Tilt Head AS INSTRUCTIONS

Cleveland, Ohio 44143

phone [phone]

Toll Free 800-530-2289

Innovative Camera Supports

Made in USA

website: www.custombrackets.com

email: [e-mail]

32 Alpha Park

Attaching the Pan-Tilt Head AS to a tripod

Attach the Pan-Tilt Head AS to the tripods’ ⅜”-16 mounting stud and tighten until rmly attached.

If you are using a tripod with a ¼”-20 mounting stud, you will need to purchase a ⅜” to ¼” reducer

* * * * *

bushing and install it in bottom of the Pan-Tilt Head’s base.

Caution

* * * * *

Arca-Swiss style
quick release

Lens lock knob

(press in and rotate

clockwise to tighten)

Tilt lock knob

(rotate counter-clockwise

Tilt drag knob

to tighten)

(rotate clockwise

to tighten)

Pan lock knob

(rotate counter-clockwise

Pan-Tilt Head AS Features

Front View

to tighten)

Using the Pan lock knob for drag may cause damage to unit. To properly

use Pan lock knob, either have it fully tighened, or fully loosened.

Attaching lens plate to lens

Mounting holes

Install screw(s) into lens plate at the labeled
ends. The screw(s) and / or plate may be
damaged if installed incorrectly. Some
lenses will require both screws be in one
slot.

The “D” screw has a fold out clip for
hand tightening. A screwdriver slot is also

A lens may have 1/4” and / or 3/8” threaded
holes. (1) 3/8” and (2) 1/4” screws are
included with each lens plate. It is important
to use the correct size.

included on the screw.

Do not insert any object as leverage into the
“D” clip as it will damage screw and void
warranty.

Attaching lens to Pan-Tilt Head AS

Attach lens with lens plate

Lens plate

reference lines

Quick release

reference lines

Lens lock knob

by loosening lens lock knob
completely, then place lens
plate into quick release. Tighten
lens lock knob completely, then
loosen 1/2 turn. Slide lens
forward or backward to balance,
then retighten lens lock knob.

If you have a replacement lens
foot, use the same procedure
above.

Indexing the quick release to accept a camera

Using the supplied allen wrench (3/16”), remove
screw from the top of the quick release, then lift
the quick release off the Pan-Tilt Head.

Align quick release far right image (Camera Setup)
and align pins using pin holes #1 & #2 (see below)
in top of the tilt head. Once in place, install screw
into the top of the quick release of the Tilt Head.
For Long Lens Setup, use pin holes #2 & #3.

Long Lens

Hole #2

Hole #1

Hole #3

Top view of Pan-Tilt Head

(quick release removed)

Pan-Tilt Head AS Features

The Pan-Tilt Head AS has many unique features. It is constructed from anodized aluminum for a lightweight

and scratch-resistent nish. The Pan-Tilt Head has separate lock and drag knobs for better control. All knobs
are captive to prevent loss. All of the fasteners are stainless steel to resist corrosion and black oxide for

appearance.

For a period of ve (5) years from date of purchase, Custom Brackets will repair or replace free of charge, any

defect in material or workmanship. Warranty does not cover repairs due to abuse, negligence, impact or any

modications made by the customer. Excessive force unscrewing knobs will void warranty. Warranty service is
available by returning the Pan-Tilt Head AS (shipping prepaid) to Custom Brackets. All returns must include a
return authorization (RA) number (contact Custom Brackets to obtain), letter explaining the problem, and a

copy of the sales receipt.

For a period of ve (5) years from date of purchase, Custom Brackets will repair or replace free of charge, any

defect in material or workmanship. Warranty does not cover repairs due to abuse, negligence, impact or any

modications made by the customer. Excessive force unscrewing knobs will void warranty. Limitation to the

warranty - after year one shipping charges are not covered. Warranty service is available by returning the Pan-

Tilt Head AS (shipping prepaid) to Custom Brackets. All returns must include a return authorization (RA) number
(email [e-mail] to obtain), letter explaining the problem, and a copy of the sales receipt.

International 5 Year Limited Warranty

USA 5 Year Warranty

Repair

Repair service is available by returning the Pan-Tilt Head AS (shipping prepaid) to Custom Brackets.
All returns must include a return authorization (RA) number (contact Custom Brackets to obtain), letter
explaining the problem, and a copy of the sales receipt. A repair cost will be issued and must be approved

prior to any repairs. Shipping charges are the responsibility of the customer.

Maintenance

The Pan-Tilt Head AS is designed completely maintenance-free.

Setup

Camera

Setup