Custom Brackets CSC2264H User Manual
CSC2264H
12” Two-Way System
Horizontal Configuration
60
O
x 40OCoverage Pattern
For Permanent Installation
Key Features:
2206H 12” VGC (Vented Gap
CooledTMLF transducer
2333 Optimized ApertureTMHF
horn with 1.5” throat
2447J 4” diaphragm, 1.5” throat
compression driver
Compact trapezoidal enclosure
DuraFlex finish - tough, weather
resistant and paintable
Tamper resistant internal Biamp/Passive crossover selector
Advanced Network Topology for
smooth power response and stable amplifier loading
Versatile complement of suspension points
The CSC2264H is a JBL Custom
Shop produced adaptation of the
Sound Power series SP212-6. The
same transducers and switchable
passive/active crossover network
have been repackaged in a horizontal configuration enclosure. All of the
features of the standard product
have been maintained while adding
installation flexibility.
The CSC2264H is available on a
build-to-order basis. Contact the
Custom Shop for information on
availability and lead time.
1
Rating based on test signal of IEC filtered random noise
with a peak-to-average ratio of 6 dB, two hours duration.
2
Sensitivity is based on a swept 500 Hz to 2.5 kHz test sig-
nal for an input of 2.83V @ 8 ohms.
JBL continually engages in research related to product
improvement. Some materials, production methods and
design refinements are introduced into existing products
without notice as a routine expression of that philosophy.
For this reason, any current JBL product may differ in some
respect from its published description, but will always equal
or exceed the original design specifications unless otherwise stated.
11/19/01 ATR
Specifications:
System:
Frequency Range (-10 dB): 37 Hz - 20 kHz
Frequency Response (±3 dB): 60 Hz - 18 kHz
Horizontal Coverage Angle (-6 dB): 80° averaged 500 Hz to 16 kHz
Vertical Coverage Angle (-6 dB): 70° averaged 500 Hz to 16 kHz
Directivity Factor (Q): 14 averaged 500 Hz to 16 kHz
Directivity Index (DI): 10.5 dB averaged 500 Hz to 16 kHz
Sensitivity2: 95 dB SPL, 1W @ 1m (3.3 ft)
Calculated Maximum SPL2: 129 dB SPL, 1W @ 1m (3.3 ft)
Nominal Impedance: 8 ohms (Passive crossover mode)
Power Rating1: 600 watts IEC, 2400 watts peak
Transducers:
Low Frequency
: 2206H, 300 mm (12 in) dia., 100 mm (4 in) edge
wound ribbon voice coil
Nominal Impedance: 8 Ohms
Power Rating: 600 watts AES, 2400 watts peak
Sensitivity2: 95 dB SPL, 1W @ 1m (3.3 ft)
Calculated Maximum SPL2: 129 dB SPL, 1W @ 1m (3.3 ft)
High Frequency
: 2447J; 100 mm (4”) diaphragm and voicecoil
dia., 76 mm (1.5”) throat dia.; 2333 horn
Nominal Impedance: 16 Ohms
Input Power Rating: 75 W AES; 300 W Peak
Sensitivity2: 112 dB, 1 W @ 1 m (3.3’)
Calculated Maximum SPL: 137 dB @ 1 m (3.3’)
Physical:
Enclosure: Trapezoidal, 15
o
top & bottom angles, 18 mm
birch plywood
Environmental Specifications: Mil-Std 810, IPX4 per IEC 529
Suspension Attachment: 12 points, accept M10 threaded hardware
Finish: Black DuraFlex coating
(white or custom color optional)
Grille: Black powder coated 18 gauge
perforated steel grille with foam backing (white or
custom color optional)
Input Connector: 2 x NL4 Neutrik Speakon connector
Dimensions (H x W x D): 394 mm x 711 mm x 378 mm
(15.5 in x 28 in x 14.88 in)
Net Weight: 31.8 kg (70 lb)
Rear
Top/Bottom
Front
28
15.5
Sides
14.88
30°
Custom Shop
Pre-Engineered
Loudspeaker Systems
Loading...