INSTRUCTIONS
CB Gimbal-LS, CB Gimbal-LB
website: www.custombrackets.com
Made in USA
email: info@custombrackets.com
32 Alpha Park
Cleveland, Ohio 44143
phone 800.530.2289
Attaching lens plate to lens
Mounting holes
Assembling CB Gimbal-LS
- - Step One - -
Base
Support plate
Tripod
We recommend only using a tripod with a
⅜”-16 mounting stud.
Place base on the tripod’s ⅜”-16 mounting
stud and rotate support plate clockwise
until base is rmly attached to tripod. Hand
tighting will be enough to secure the base to
tripod. It is not recommended to use pan
knob to secure support plate to tripod.
* * * * *
If you choose to use a tripod with a ¼”
mounting stud, test tripod to make sure it
will handle the weight of camera and lens
combination. You will need to purchase a
⅜” to ¼” reducer bushing and install it in
bottom of CB Gimbal-LS’s support plate.
Caution
* * * * *
Pan knob for
drag and lock
Assembling CB Gimbal-LB
- - Step Two - -
Lens platform
Arm
Safety stop
Loosen lens platform knob and slide lens
platform into arm until it rests on the safety
stop. Tighten lens platform knob to secure
lens platform.
Note
Final height location of lens platform is
explained in “CB Gimbal-LS Features” on
reverse side.
* * * * *
* * * * *
Lens platform
lock lever
Lenses either have ¼” or ⅜” threads. (1) ⅜” and (2) ¼” screws
are included with each lens plate - it is important to use the
correct size.
Install screw(s) into lens plate at the labeled ends. If not, the
screw(s) may be damaged. Some lenes will require that both
screws be in one slot for balancing the lens.
The “D” screws have fold out clips for hand tightening. To
make it tighter, use a straight screwdriver or quarter.
Screw the GLM-1 or GLM-2 to the bottom of your lens foot
using the “D” screws that correspond to the lens mounting
holes.
Do not insert any object as leverage into the “D” clip.
Attaching GLA (lens anti-twist)
to GLM-2 (lens plate)
GLA
Anti-twist screws
GLM-2
¼” threaded hole
If using the optional GLA (lens anti-twist), use the ¼” threaded
screw that is included with the GLM-2 (lens plate). Attach the
GLA on top of the GLM-2 and tighen down. Once the lens
is attached per the insctructions below, position the GLA so
that it is closest to the lens foot. Next, tighten each anti-twist
screw equally towards the center until they are tight against
the lens foot.
Base
Support plate
Tripod
We recommend only using a tripod with a
⅜”-16 mounting stud.
Place base on the tripod’s ⅜”-16 mounting
stud and rotate support plate clockwise
until base is rmly attached to tripod. Hand
tighting will be enough to secure the base to
tripod. It is not recommended to use pan
lock to secure support plate to tripod.
* * * * *
If you choose to use a tripod with a ¼”
mounting stud, test tripod to make sure it
will handle the weight of camera and lens
combination. You will need to purchase a
⅜” to ¼” reducer bushing and install it in
bottom of CB Gimbal-LB’s support plate.
Caution
* * * * *
Attaching lens to
CB Gimbal-LS
Lens plate setup
reference lines
Camera platform
reference lines
Lens platform lock knob
Rotate setup lever into arm pocket
(see “CB Gimbal-LS Features” for location on reverse side).
Install lens plate by loosing lens lock knob all the way, then
place lens plate into lens platform. Tighten lens platform lock
knob completely, then loosen ½ turn. Slide lens plate forward
or backward to achive balance, then retighten lens platform
lock knob.
Achieving balance is similiar on CB Gimbal-LB.
* * * * *
Note
* * * * *
Adjusting the lens center height
For balancing the lens, position the lens
slighty above the center of the tilt axis
(best position is when lens stays
at any angle without drag)
Center of Tilt Axis
- - - CB Gimbal-LS Features - - -
TILT
Tilt knob for
drag and lock
Lens lock lever
Lens platform lock lever
PA N
Arca Swiss style clamp
Lens lock lever
Lens platform lock lever
Setup knob
for balancing lens,
changing cameras, and
secure travel while on tripod
- - - CB Gimbal-LB Features - - -
Lens lock lever
push in and turn
to lock or unlock
TILT
Tilt knob for
drag and lock
Setup knob
Pan knob for
drag and lock
PA N
Pan knob for
drag and lock
CB Gimbal-LS and CB Gimbal-LB Facts
The CB Gimbal-LS and CB Gimbal-LB have many unique features found only in our Custom Brackets gimbal line. It is constructed from aircraft aluminum that is “hard anodized” for a lightweight and scratch
resistent nish. All levers have an ergonomic design and are machined from aluminum to prevent breakage. All of the fasteners are made from stainless steel to resist corrosion. The pan and tilt knobs
have a rubberized coating for comfort, traction, and to resist cold weather. The CB Gimbal-LS has a setup / travel knob that is used for balancing the lens and securing for travel from location to another
when the lens is still attached.
USA 5 Year Warranty
For a period of ve (5) years from date of purchase, Custom Brackets will repair or replace free of charge, any defect in material or workmanship. Warranty does not cover repairs due to customer abuse,
negligence, impact or any modications made by the customer. All knobs are installed using “loctite” to prevent them from unscrewing. Hand tightening is sufcient to secure any component and the lens
plate. Excessive force unscrewing will cause the knobs to unscrew and void warranty. Warranty service is available by returning the CB Gimbal-LS or CB Gimbal-LB (shipping prepaid) to Custom Brackets.
All returns must include a return authorization (RA) number (contact Custom Brackets to obtain), letter explaining the problem, and a copy of the sales receipt.
International 5 Year Limited Warranty
For a period of ve (5) years from date of purchase, Custom Brackets will repair or replace free of charge, any defect in material or workmanship. Warranty does not cover repairs due to customer abuse,
negligence, impact or any modications made by the customer. All knobs are installed using “loctite” to prevent them from unscrewing. Hand tightening is sufcient to secure any component and the lens
plate. Excessive force unscrewing will cause the knobs to unscrew and void warranty. Limitation to the warranty - after year one shipping charges are not covered. Warranty service is available by returning
the CB Gimbal-LS or CB Gimbal-LB (shipping prepaid) to Custom Brackets. All returns must include a return authorization (RA) number (contact Custom Brackets to obtain), letter explaining the problem,
and a copy of the sales receipt.
Repair
Repair service is available by returning the CB Gimbal-LS or CB Gimbal-LB (shipping prepaid) to Custom Brackets. All returns must include a return authorization (RA) number (contact Custom Brackets
to obtain), letter explaining the problem, and a copy of the sales receipt. A repair cost will be issued and must be approved prior to any repairs. Shipping charges are the responsibility of the customer.
Maintenance
The CB Gimbal-LS and CB Gimbal-LB are designed to be completely maintenance-free. The bearing rotation tension is factory set. Attempting to adjust the tension will void the warranty and may result in
damage to the camera or lens.
Loading...