Curtron Service-Pro Traffic Doors 20 User Manual

Section 08380
Double Acting Impact Traffic Doors

Curtron Products – Service-Pro Traffic Doors – Series 20

PART 1 - GENERAL

1.1 WORK INCLUDED

1.1.1 Related sections: Include appropriate section below indicating proper frame/jamb details.
Recommended jamb is ¼” thick and 4” wide minimum steel frame .

1.2 SUBMITTALS

1.2.1 Product data: Submit manufacturer’s data indicating products provided.

1.2.2 Shop drawings: Submit indicating locations of required block outs, frame fabrication
requirements, sizes, elevations, and other related items.

1.3 DELIVERY, STORAGE AND HANDLING

1.3.1 Packing and shipping: Deliver work packaged for protection.

1.3.2 Acceptance at site: Inspect work upon delivery for damage; rejecting any damaged items.

1.3.3 Storage and protection: Store materials under cover, 4” off floor minimum, raised
platforms, in vertical position with minimum ¼” space between doors. Avoid use of non­ vented plastic or canvas shelters creating humidity chambers. Immediately remove wet
wrappers.

PART 2 - PRODUCTS

2.1 ACCEPTABLE MANUFACTURERS

2.1.1 Curtron Products, 5350 Campbells Run Road, Pittsburgh, PA 15205
Phone: [phone] / Fax: [phone]
Email: [e-mail]

/ Web: www.curtronproducts.com

2.1.2 Products of the similar type acceptable only if matching the specified requirements.

2.2 MATERIALS

2.2.1 Door Type: Service-Pro Traffic Doors

2.2.2 Traffic Type: Retail/Commercial, Personnel Traffic

2.2.3 Sizes: As indicated on drawings (door schedule)

2.2.4 Panels: Constructed of .063” anodized aluminum panel, with leading edge structurally
formed for added strength. Jamb edge of panel reinforced with 3/8” plywood on both
sides with formed cover of anodized aluminum.

2.2.5 Finishes: Choice of Natural Aluminum Finish, Wood Laminate (Architect to chose color
from standard manufacturer’s Wilsonart, Formica, Nevamar, or Pionite), or Satin Brushed
16 Gauge Stainless Steel

7/15/2009 CSISERIES20 Traffic Doors 08380-1

2.2.6 Hardware: Hinges are double action Save-T style with hardened rollers, hinge covers and
bottom pin system. Hinge options are galvanized or stainless steel. Bi-parting door
panels 36” wide and smaller utilize café, gate style hinges.

2.2.6.1 Accessories: Optional galvanized or stainless steel 10” or 18” jamb guards.

2.2.7 Vision Window: Standard 9” x 14” clear vision panel held securely in place by a gasket­ style custom rubber extrusion; Standard 6” x 12” clear vision panel for bi-parting doors
36” or smaller.

2.2.7.1 Optional Window Sizes: 14” x 16”; 10” x 30”; 22” x 22”; 10” Round; 20” Round

2.2.7.2 Window Style: Clear acrylic; smoked/tinted (excluding round); mirrored
(excluding round).

2.2.8 Panel Protection: Optional impact plates in stainless steel; galvanized steel; colored ABS;
Optional black teardrop bumper; or Optional stainless steel or thermoplastic push plates.

2.2.8.1 Impact Plate Heights: 12”; 18”; 24”; 30”; 36”; 42”; 48”

PART 3 - EXECUTION

3.1 DOOR INSTALLATION

3.1.1 Verify traffic door frames are in accord with reviewed shop drawings.

3.1.2 Examine conditions and substrates under which products of this section are to be
installed.

3.1.3 Submit written notification of unacceptable conditions or substrates.

3.1.4 Submit copy of installer’s report to Architect of record within 72 hours of report
receipt.

3.2 PROCEEDING WITH CONSTRUCTION ACTIVITY

3.2.1 Prior to correction of unacceptable conditions or substrates are prohibited.

3.2.2 Indicate installer’s acceptance of condition of product and substrates.

3.3. INSTALLATION

3.3.1 Steel tube frames: Installed in Metal Fabrication section.

3.3.2 Install in prepared openings in accord with reviewed shop drawings and manufacturer’s
Installation instructions. Plumb and level units. Adjust for proper operation.

3.3.3 Clean surfaces in accord with manufacturer’s instructions just prior to Date of Substantial
Completion.

++ END OF SECTION ++

7/15/2009 CSISERIES20 Traffic Doors 08380-2