SDPF887
Table of Contents
Safety Precaution
Safety Precaution
Introduction
Installing your unit
Main unit control
System connection
Using your remote control
Using Your Digital Picture Frame
on the remote control
Browsing images
Setup
Troubleshooting
Specifications
1
3
3
4
4
5
6
6
7
9
9
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Introduction
Congratulations on your purchase of Digital Photo Frame, model SDPF887.
Before operating the units, please read this manual thoroughly, and retain it for future
reference. This manual will help you use many of the exciting and useful features that
will make your Digital Photo Frame viewing more enjoyable.
This Digital Photo Frame lets you view digital pictures directly from your camera's
memory cards. You will be able to create a slideshow using multiple transition effects or
display one picture at a time.
This Digital Photo Frame is compatible with the following popular memory card
formats: USB, SD,MultiMedia Card, and Memory Stick.
Package Contents
Power Adaptor
Digital Photo Frame
User's Manual
Remote Control
Stand
Installing Your Unit
Locate the removable easel and place in the corresponding holes at the back of the unit.
Plug in the AC adaptor into power outlet. Plug the other end into the unit.
After the connect is stored on the target flash device. Insert the device into the correct
slot.
Note: Please ensure that you have one photo file loaded onto the memory card.
3
Main Unit Controls
Using your SD card
5
7
6
4
3
MODEL: SDPF887
2
SD
1
DC IN 5V
DC INPUT: 5V 1A
MADE IN CHINA
1. DC in 5V 2.SD card slot
3. USB port 4. ON/OFF :turn on and turn off the unit
5. :Use this button to move cursor up and down when at setting menu, and at main
menu,you can use this button to select media device.
: Use this button to move cursor left and right when at setting menu and main menu.
when playing JPEG files,press it to play prev/next JPEG file.
6.OK:To confirm.
7.M:Press it to return the main menu at once.
System Connection
Power connection
Upon using an SD card, insert it to the corresponding slot flatly with the label side
backward.
DC IN 5V
SD
Note: Please do not disconnect USB device or plug out SD/MMC/MS card while they
are working with the unit. Functional failure may occur in case of wrong operations.
Using Your Remote Control
Button Description and Function:
Setup: To enter into setup menu
Use this button to move cursor up and down when at
:
setting menu, and at main menu,you can use this
button to select media device.
Use this button to move cursor left and right when at
:
setting menu and main menu. when playing JPEG files,
press it to play prev/next JPEG file.
Esc: Return to the previous step.
OK
: To confirm and play/pause.
ZOOM: when the picture is displaying,press is repeatedly can zoom out the picture
by 125%,150%,175%,200%,225%,250%.
ROTATE: when displaying pictures,press it to rotate the picture 90°,180°,270°,0°.
ZOOM
ESC
ROTATE
SETUP
OK
DC IN 5V
SD
Plug one end of the supplied AC/DC power adaptor into the DC input jack of the machine,
then plug the other end into the AC power receptacle. Please refer to the illustration
above.
4
E
S
C
Z
O
O
M
RO
OK
T
AT
S
E
E
T
UP
5
Using Your Digital Picture Frame on the remote control
Make sure you have at least one image file on your memory cards or USB flash drive.
Switch on the frame and insert memory cards into the unit, it will automatically start
slideshow.
Press “Esc” button on the remote control, until it display the main menu.
USB
SETUP
Press “Setup” button on the remote control to enter setup menu when you are at other
menu.
In the Setup menu, press button to highlight the item. Press button to access.
Press ESC to exit.
SETUP
Photo Setup
Calendar Setup
System Setup
OK
1616
Photo
Calendar
Press “Esc” button repeat edly, cursor position will move to SD/MMC/MS-USB media device.
Using the directional arrows ,highlight the desired SD/MMC/MS-USB media
device.press button to select one device,then you can enter into PHOTO/CALENDER
/SET UP interface by press button.
OK
OK
Browsing Images
When displaying the pictures,you can press “Esc” button to return to thumbnail.And you
can use to select the picture,press button to browse the picture,
you have selected.
Setting
OK
PHOTO SETUP
In the Photo Setup menu, press to highlight the item. Press to change
the settings. Press ESC to return the Setup menu.
Display Mode: Select image display mode (Slideshow,Thumbnail,Browse Mode)
Display Ratio:Select image display size(Fit to Screen,Crop to Fill,Full Screen)
Slideshow time:Select the duration of time (5Sec,15Sec,30Sec,60Sec,5Min,15Min)
Slideshow Repeat : Select the manner of repeating photos (Once,Repeat)
Transition effect: Adjust the transition effect between eachimage in a slideshow.
Optional effect includes Random/Snake/Partition/Erase/Blinds/Random lines/Grid/
Gross/Rect/Spital/Close.
Photo Setup
Display Mode
Display Ratio
Slide Show Time
SlideShow Repeat
Transition effect
Calendar Setup
Display Mode : Select calendar display mode (Calendar/Digital Clock/Analog Clock)
Set Date : When the cursor position moving to the Icon,using the directional arrows
to adjust the date.
Clock Mode : When the cursor position moving to the Icon,using the directional to
adjust the Clock Mode(24hr,12hr).
Set Time :When the cursor position moving to the Icon,using the directional
to adjust the time.
Slideshow
Fit to Screen
5Sec
Repeat
Random
6
7
Calendar Setup
Display Mode
Set Date
Clock Mode
Set Time
Calendar
01-01-2010
24hr
00:03
System setup
Language : Select the on screen display language English/Deutsch/French/Italian.
Backlight : you can adjust the Backlight (between 1,2,3,4,5).
Brightness :Adjust screen brightness(between 0,1,2,3,4,5,6)
Contrast : Adjust screen contrast(between 0,1,2,3,4,5,6)
Saturation : Adjust screen saturation (between 0,1,2,3,4,5,6)
Power On : When the cursor position moving to the Icon,using the directional “ ”to
select the unit auto Power on mode(on/off),
Auto Boot Time : When the cursor position moving to the Icon,using the directional
“ ” to select the unit auto Power on time.
Power Off : When the cursor position moving to the Icon,using the directional “ ”to
select the unit auto Power off mode(on/off),
Auto Shut Time : When the cursor position moving to the Icon,using the directional
to select the unit auto Power off time.
Auto-Power Frequency : When the cursor position moving to the Icon,using the
directional “ ”to select the unit Auto-Power Frequency mode(Everyday/Mon.to
Fri./Weekend/Once),
Default : When the cursor position moving to the Icon, pressing “ ” to show
the dialog,and select “YES”,press“ ” to revert to the factory settings.
Ver : When the cursor position moving to the Icon, pressing “ ” to show the
dialog of the software version number.
OK
System Setup
Language
Backlight
Brightness
Contrast
Saturation
Power On
Auto Boot Time
Power Off
English
5
3
3
5
Off
00
Off
OK
OK
Troubleshooting
Symptom
Digital Photo
Frame doesn't
power on
No photo files
on the memory
card
The file doesn't
play.
The power connector
to the unit is not
securely inserted.
Card is wrongly
inserted
Incompatible file
format
Specifications
Type
Resolution
Output
Input
Working Temperature
Display Mode
File Format
Cards
Dimension
Weight
Cause Corrective Actions
Make sure you connect the AC adaptor to the
frame properly. When you connect the AC
adaptor to the frame and power on the unit,
even without a memory card, you should see
the main menu. If you don't see it, check if
the power is connected to the Digital Photo
Frame and make sure it is securely attached.
Verify if the way you inserted the card is
correct. Make sure the front label of the
memory card is facing AWAY from the front
of the unit. Do not force the memory card
into the slot.
Make sure there is at least one supported
image file on the memory card.
Compatible photo format: JPEG
8 inch Digital Photo Frame
800*600 Pixel
5V 1.0 A
AC100-240V~50/60Hz
0-40°C
4:3
JPEG
SD/MMC/MS
260*220*50 mm
0.85 kg
8
9
Loading...