FIND OUT MORE
ON
THE WEB.
WILBURCURTIS.COM
Installation Instructions,
Service & Warranty Information
Revised: Aug 2001
MODELS INCLUDEDMODELS INCLUDED
MODELS INCLUDED
MODELS INCLUDEDMODELS INCLUDED
••
• SLG
••
••
• ISLG
••
CURTIS LOW-PROFILE COFFEE GRINDERS
WILBUR CURTIS COMPANY Montebello, CA 90640
C
ISO 9001 REGISTERED
FOR THE LATEST SPEC INFORMATION GO TO WWW.WILBURCURTIS.COM
SLG Grinder
ISLG InterLock
DRAFT COPY
Not Released. This Version Exists as File No.
I:\DIAGRAMS\FRANK\FX-134.p65
•
Grinder
F
IND OUT MORE
FIND OUT MORE
THE WEB.
ON
ON
THE WEB.
WILBURCURTIS.COM
WILBURCURTIS.COM
WW
W
WW
ILBURILBUR
ILBUR
ILBURILBUR
C C
C
C C
URTISURTIS
URTIS
URTISURTIS
C C
C
C C
OMPOMP
OMP
OMPOMP
ANYANY
ANY
ANYANY
, I, I
, I
, I, I
NCNC
NC
NCNC
..
.
..
Models Included
SLG
ISLG
CAUTION: CAUTION:
CAUTION: Please
CAUTION: CAUTION:
use this setup
attempting to use this grinder.
Failure to follow the instructions
can result in injury or the voiding
of the warranty.
procedure before
InstallaInstalla
Installa
InstallaInstalla
Important Safeguards/ConventionsImportant Safeguards/Conventions
Important Safeguards/Conventions
Important Safeguards/ConventionsImportant Safeguards/Conventions
This appliance is designed for commercial use. Any servicing other than cleaning and maintenance should be performed by an
authorized Wilbur Curtis service center.
ConventionsConventions
Conventions
ConventionsConventions
QUICK STQUICK ST
QUICK ST
QUICK STQUICK ST
1. Install the grinder on a firm, level base in a location where it can be connected to a grounded electrical outlet of 120VAC,
rated at 15 amps.
2. Test the unit by running some whole bean coffee through the grinder. If any problems are encountered, refer to the
troubleshooting section complete at www.wilburcurtis.com or call Technical Service at 800-995-0417.
SETUP INSTRUCTIONS - ISLGSETUP INSTRUCTIONS - ISLG
SETUP INSTRUCTIONS - ISLG
SETUP INSTRUCTIONS - ISLGSETUP INSTRUCTIONS - ISLG
1. Turn both units OFF.
2. Place the grinder close enough to the brewer so the InterLock cable will reach the brewer.
tion Instructions,tion Instructions,
tion Instructions,
tion Instructions,tion Instructions,
• Do NOT immerse the unit in water or any other liquid
• To reduce the risk of fire or electric shock, do NOT open top panel. No user serviceable parts inside. Repair should be done
only by authorized service personnel.
• Keep hands and other items away from hot parts of unit during operation.
• Never clean with scouring powders or harsh implements.
WW
ARNINGS – ARNINGS –
W
ARNINGS –
WW
ARNINGS – ARNINGS –
ARAR
AR
ARAR
TT
o help ao help a
void personal injurvoid personal injur
T
o help a
void personal injur
TT
o help ao help a
void personal injurvoid personal injur
T & SETUP - SLGT & SETUP - SLG
T & SETUP - SLG
T & SETUP - SLGT & SETUP - SLG
OPERAOPERA
TING INSTRTING INSTR
OPERA
TING INSTR
OPERAOPERA
TING INSTRTING INSTR
The SLG grinder is adjusted at the factory to grind 2 - 2.5 ounces of medium roast coffee.
Ser Ser
Ser
Ser Ser
yy
y
yy
UCTIONS - SLGUCTIONS - SLG
UCTIONS - SLG
UCTIONS - SLGUCTIONS - SLG
vice & vice &
vice &
vice & vice &
WW
arranty Informaarranty Informa
W
arranty Informa
WW
arranty Informaarranty Informa
Important Notes/Cautions – from the factorImportant Notes/Cautions – from the factor
Important Notes/Cautions – from the factor
Important Notes/Cautions – from the factorImportant Notes/Cautions – from the factor
tiontion
tion
tiontion
yy
y
yy
WARNING TO AVOID
SCALDING, Do not
remove brewcone
while brew light is flashing.
C
ISO 9001 REGISTERED
WILBUR CURTIS COMPANY
Montebello, CA 90640
1. Lift off the clear hopper lid and fill the hopper with whole coffee beans.
2. Place a new filter into your brew cone. Slide the brew cone into the brew cone rails on the grinder.
3. Push the START switch on the front panel. The SLG will start to grind coffee into the brew cone.
4. Wait for the grinder motor to stop before removing the brew cone.
OPERAOPERA
TING INSTRTING INSTR
OPERA
TING INSTR
OPERAOPERA
TING INSTRTING INSTR
Factory settings: SMALL grind button, set for 5 seconds (1.3 oz). LARGE grind
button, set at 15 seconds (3.8 oz). ISLG -13, has additional MEDIUM button set
for 10 seconds.
1. Place the brew cone into the rails on the grinder. Press one of the grind
buttons on the switch panel. Ground coffee will start to fill the brew cone.
2. When the grinder motor stops, remove the brew cone and slide it into the rails
on the brewer.
3. Press the brew switch that displays the blinking indicator light. This starts a brew cycle.
To cancel a brew cycle, press the ON/OFF switch on the brewer. Brew cycles in process will be
cancelled.
ADJUSTING THE GRINDSADJUSTING THE GRINDS
ADJUSTING THE GRINDS
ADJUSTING THE GRINDSADJUSTING THE GRINDS
Refer to illustration page 2.
1. Empty hopper of coffee beans. Run grinder to clear grinding burrs of coffee.
2. Open housing cover to locate adjustment screw (8) and lock nut (7). Loosen lock nut.
3. Run motor during adjustment. Turning adjustment screw clockwise will result in a finer grind (if, while turning, you hear the
grinding burrs starting to touch, immediately, back off 1/8th turn). Turning counter clockwise will produce a coarser grind.
4. With a screwdriver holding the adjustment screw in place, tighten the locknut.
5. Run some coffee beans through the machine to check the grind adjustment.
6. Replace front cover on machine.
*This adjustment may change the amount of ground coffee dispensed.
UCTIONS - ISLGUCTIONS - ISLG
UCTIONS - ISLG
UCTIONS - ISLGUCTIONS - ISLG
FOR THE LATEST SPECIFICATIONS AND INFORMATION GO TO
WWW.WILBURCURTIS.COM
1
Loading...