CAB INSTALLATION INSTRUCTIONS
JOHN DEERE 2305, 2210
HARD SIDED CAB ENCLOSURE (p/n 1JD2305AS)
SOFT SIDED CAB ENCLOSURE (p/n 1JD2305SS)
The contents of this envelope are the property of the owner.
Be sure to leave with the owner when installation is complete.
This Curtis Cab is designed and
manufactured for use only as reasonable
cable, Nor should the cab be considered as protection against
roll over, collision or other accidents that may result. This cab is
NOTaR.O.P.S.cab. Extreme care should be taken when operat-
ing and by qualified, experienced operators only.
INSTALLATION & OWNER’S MANUAL
weather protection. This cab is not appli-
CABS/BLADES/ SPREADERS/ACCESSORIES
Note: soft side cab shown
ExposuretoCarbonMonoxidecanCause
illness,seriousinjuryordeath.Never
Monoxide. Inspect exhaust system for leaks monthly. Leaks can
result from loose connections, corrosion, cracks or other damage
to the exhaust manifold. If leaks are found, repair or replace
exhaust system. Do not use vehicle until repair or replacement is
complete.
operate vehicle if suspicious of Carbon
ADDED
WEIGHT
Curtis Cabs, blades and general accessories
add additional weight to the base vehicle. All
Curtis accessory weights are listed in product
brochures. Deduct the accessory's total weight
from the vehicle's rated capacity and never
exceed the vehicle's rated capacity including
driver and passenger.
p. 1 of 8, Rev. J,
1/3/2012
p/n: IM-1JD2305
DESIGN CONCEPT
Curtis Cabs feature an assembly of parts designed for your vehicle which require
adjustment and alignment of components to accommodate vehicle variations and
provide proper weather protection. For accurate installation, proper operation, and
years of satisfaction, please read and understand the installation instructions.
From all of us at Curtis, we thank you for choosing our product.
ADDED
WEIGHT
Curtis Cabs, blades and general accessories
add additional weight to the base vehicle. All
Curtis accessory weights are listed in product
brochures. Deduct the accessory's total weight
from the vehicle's rated capacity and never
exceed the vehicle's rated capacity including
driver and passenger.
weather protection. This cab is not appl ic a ble, no r sh oul d
the cab be considered as protection against roll over,
collision or other accidents that may result. This cabs is
NOTaR.O.P.S.cab. Extreme care should be taken when
operating and by qualified, experienced operators only
This Curtis Cab is designed and manu factured for use only as reasonable
.
ExposuretoCarbonMonoxidecan
Causeillness,seriousinjuryordeath.
Never operate vehicle if suspicious of Carbon Monoxide.
Inspect exhaust system for leaks monthly. Leaks can result
from loose connections, corrosion, cracks or other damage
to the exhaust manifold. If leaks are found, repair or replace
exhaust system. Do not use vehicle until repair or replacement is complete.
CAB INSTALLATION
BEFORE YOU START
HELPFUL REMINDERS:
A. Leave all bolts loose for later adjustment unless otherwise specified.
B. Read and understand all instructions before beginning.
C. Plastic washers have been supplied to provide a weather seal around
all button head exterior fasteners. The plastic washer should be installed
under each bolt head directly against the outside cab surface. Care
should be taken not to over tighten the fasteners and damage the plastic
washer. Also use metal washers as required.
D. Apply a clear silicone sealant to seal any minor gaps that may occur due
to vehicle variances. E.G. front legs to bottom of unitized frames.
TOOLS REQUIRED:
1/2 IN.
3/8 DRIVE
DEEP
SOCKET
NO. 2 MEDIUM
PHILLIPS HEAD
SCREWDRIVER
7/16 IN.
3/8 DRIVE
SOCKET
18 mm.
3/8 DRIVE
SOCKET
12 mm
3/8 DRIVE
SOCKET
3/16 INCH
ALLEN
DRIVE
3/8 DRIVE
13 mm
3/8 DRIVE
SOCKET
3/8 DRIVE
RATCHET
13 mm
OPEN END
WRENCH
SNIPS
1/2 IN.
OPEN END
WRENCH
7/16 IN.
OPEN END
WRENCH
p. 2 of 8
111 HIGGINS STREET, WORCESTER, MA 01606
MODEL: JOHN DEERE 2305, 2210 HARD SIDE & SOFT SIDE CABS
NOTE: This cab is designed to fit the 2210 and 2305 tractors
with 210, 200X or 200CX loaders. It may or may not fit with other attachments or aftermarket loaders.
1. VEHICLE PREP
1.1 Remove SMV sign and bracket. On 2305 models r-install the turn
signal light with the hardware removed with the SMV bracket.
1.2 (See figure 1) Remove and discard bolts from the tractor floorboard
as shown. There are 2 bolts on the left side but only one on the right
side.
1.3 (See Figure 1) Remove seat belt holder bracket and the bolt next to
it from the base of the roll bar on both sides of the tractor. Retain for
later use.
1.4 (See Figure 2) The plastic floorboard of the tractor must be leveled
before installing the cab. If the tractor is parked on a flat floor measure from the ground to the top of the floor board just in front of the
rear fenders. If no level surface is available block a straight edge up
against the bottom of the tractor frame and measure from it to the
top of the floorboard. If the right side is lower than the left have an
assistant lift up the right side of the floorboard and stack fender
washers from the hardware kit between it and the mounting bracket
where the bolt was removed in Step 1.2. Add washers to make the
measurement the same as the left side.
2. FRONT COWL ASSEMBLY
2.1 (See Figure 3) NOTE: Part descriptions can be found on pages 7
and 8. Assemble the left and right front legs to the cowl with a 5/16”
X 3/4” long button head screw at the inside holes only. Assemble so
that the cowl is on the outside of the front legs. NOTE: Use a nylon
washer in addition to the steel washers on all exterior button head
bolts as explained in helpful reminders on the previous page. Align
the outer edges and tighten the bolts.
2.2 (See Figure 3) Install one of the pieces of 1” flat bulb from the
hardware kit along the inner sheet metal edges. Trim so that the bulb
ends even with the bulb already installed on the bottom of the legs.
2.3 (See Figure 4) Place cowl assembly onto the tractor. The 1” flat
bulb should point forward. NOTE: On 2305 models the cowl co-
vers the operation decal. It is highly recommended a new decal,
part # LVU14471, be purchased from John Deere. Install the
decal on the inside of the cowl above the old decal.
FIGURE 1
FIGURE 2
BOLT
TRIM EVEN
FIGURE 3
FIGURE 4
CABS/BLADES/ SPREADERS/ACCESSORIES
p. 3 of 8
Loading...