Page 1
CAB INSTALLATION INSTRUCTIONS
JOHN DEERE 2305, 2210
HARD SIDED CAB ENCLOSURE (p/n 1JD2305AS)
SOFT SIDED CAB ENCLOSURE (p/n 1JD2305SS)
The contents of this envelope are the property of the owner.
Be sure to leave with the owner when installation is complete.
This Curtis Cab is designed and
manufactured for use only as reasonable
cable, Nor should the cab be considered as protection against
roll over, collision or other accidents that may result. This cab is
NOTaR.O.P.S.cab. Extreme care should be taken when operat-
ing and by qualified, experienced operators only.
INSTALLATION & OWNER’S MANUAL
weather protection. This cab is not appli-
CABS/BLADES/ SPREADERS/ACCESSORIES
Note: soft side cab shown
ExposuretoCarbonMonoxidecanCause
illness,seriousinjuryordeath.Never
Monoxide. Inspect exhaust system for leaks monthly. Leaks can
result from loose connections, corrosion, cracks or other damage
to the exhaust manifold. If leaks are found, repair or replace
exhaust system. Do not use vehicle until repair or replacement is
complete.
operate vehicle if suspicious of Carbon
ADDED
WEIGHT
Curtis Cabs, blades and general accessories
add additional weight to the base vehicle. All
Curtis accessory weights are listed in product
brochures. Deduct the accessory's total weight
from the vehicle's rated capacity and never
exceed the vehicle's rated capacity including
driver and passenger.
p. 1 of 8, Rev. J,
1/3/2012
p/n: IM-1JD2305
Page 2
DESIGN CONCEPT
Curtis Cabs feature an assembly of parts designed for your vehicle which require
adjustment and alignment of components to accommodate vehicle variations and
provide proper weather protection. For accurate installation, proper operation, and
years of satisfaction, please read and understand the installation instructions.
From all of us at Curtis, we thank you for choosing our product.
ADDED
WEIGHT
Curtis Cabs, blades and general accessories
add additional weight to the base vehicle. All
Curtis accessory weights are listed in product
brochures. Deduct the accessory's total weight
from the vehicle's rated capacity and never
exceed the vehicle's rated capacity including
driver and passenger.
weather protection. This cab is not appl ic a ble, no r sh oul d
the cab be considered as protection against roll over,
collision or other accidents that may result. This cabs is
NOTaR.O.P.S.cab. Extreme care should be taken when
operating and by qualified, experienced operators only
This Curtis Cab is designed and manu factured for use only as reasonable
.
ExposuretoCarbonMonoxidecan
Causeillness,seriousinjuryordeath.
Never operate vehicle if suspicious of Carbon Monoxide.
Inspect exhaust system for leaks monthly. Leaks can result
from loose connections, corrosion, cracks or other damage
to the exhaust manifold. If leaks are found, repair or replace
exhaust system. Do not use vehicle until repair or replacement is complete.
CAB INSTALLATION
BEFORE YOU START
HELPFUL REMINDERS:
A. Leave all bolts loose for later adjustment unless otherwise specified.
B. Read and understand all instructions before beginning.
C. Plastic washers have been supplied to provide a weather seal around
all button head exterior fasteners. The plastic washer should be installed
under each bolt head directly against the outside cab surface. Care
should be taken not to over tighten the fasteners and damage the plastic
washer. Also use metal washers as required.
D. Apply a clear silicone sealant to seal any minor gaps that may occur due
to vehicle variances. E.G. front legs to bottom of unitized frames.
TOOLS REQUIRED:
1/2 IN.
3/8 DRIVE
DEEP
SOCKET
NO. 2 MEDIUM
PHILLIPS HEAD
SCREWDRIVER
7/16 IN.
3/8 DRIVE
SOCKET
18 mm.
3/8 DRIVE
SOCKET
12 mm
3/8 DRIVE
SOCKET
3/16 INCH
ALLEN
DRIVE
3/8 DRIVE
13 mm
3/8 DRIVE
SOCKET
3/8 DRIVE
RATCHET
13 mm
OPEN END
WRENCH
SNIPS
1/2 IN.
OPEN END
WRENCH
7/16 IN.
OPEN END
WRENCH
p. 2 of 8
Page 3
111 HIGGINS STREET, WORCESTER, MA 01606
MODEL: JOHN DEERE 2305, 2210 HARD SIDE & SOFT SIDE CABS
NOTE: This cab is designed to fit the 2210 and 2305 tractors
with 210, 200X or 200CX loaders. It may or may not fit with other attachments or aftermarket loaders.
1. VEHICLE PREP
1.1 Remove SMV sign and bracket. On 2305 models r-install the turn
signal light with the hardware removed with the SMV bracket.
1.2 (See figure 1) Remove and discard bolts from the tractor floorboard
as shown. There are 2 bolts on the left side but only one on the right
side.
1.3 (See Figure 1) Remove seat belt holder bracket and the bolt next to
it from the base of the roll bar on both sides of the tractor. Retain for
later use.
1.4 (See Figure 2) The plastic floorboard of the tractor must be leveled
before installing the cab. If the tractor is parked on a flat floor measure from the ground to the top of the floor board just in front of the
rear fenders. If no level surface is available block a straight edge up
against the bottom of the tractor frame and measure from it to the
top of the floorboard. If the right side is lower than the left have an
assistant lift up the right side of the floorboard and stack fender
washers from the hardware kit between it and the mounting bracket
where the bolt was removed in Step 1.2. Add washers to make the
measurement the same as the left side.
2. FRONT COWL ASSEMBLY
2.1 (See Figure 3) NOTE: Part descriptions can be found on pages 7
and 8. Assemble the left and right front legs to the cowl with a 5/16”
X 3/4” long button head screw at the inside holes only. Assemble so
that the cowl is on the outside of the front legs. NOTE: Use a nylon
washer in addition to the steel washers on all exterior button head
bolts as explained in helpful reminders on the previous page. Align
the outer edges and tighten the bolts.
2.2 (See Figure 3) Install one of the pieces of 1” flat bulb from the
hardware kit along the inner sheet metal edges. Trim so that the bulb
ends even with the bulb already installed on the bottom of the legs.
2.3 (See Figure 4) Place cowl assembly onto the tractor. The 1” flat
bulb should point forward. NOTE: On 2305 models the cowl co-
vers the operation decal. It is highly recommended a new decal,
part # LVU14471, be purchased from John Deere. Install the
decal on the inside of the cowl above the old decal.
FIGURE 1
FIGURE 2
BOLT
TRIM EVEN
FIGURE 3
FIGURE 4
CABS/BLADES/ SPREADERS/ACCESSORIES
p. 3 of 8
Page 4
111 HIGGINS STREET, WORCESTER, MA 01606
MODEL: JOHN DEERE 2305, 2210 HARD SIDE & SOFT SIDE CABS
3. SIDE FRAMES
3.1 With assistance, remove doors from side frames (for easier han-
dling) by unlatching and sliding up and off the hinge pins.
3.2 (See Figure 5) Assemble left and right rear legs to the left and right
side frames with 5/16” X 3/4” button head screws in all but the top
holes. Cut the remaining piece of 1” flat bulb from the hardware kit
in half. Install along the bottom edge of the rear leg and along the
contour of the frame. Do not trim rubber at this time.
3.3 (See Figure 6) Install the left side frame onto the tractor by installing the bolts and seat belt holder removed in step 1.2 through
the base of the rear leg. Attach to floorboard with 5/16” X 1-3/4”
long carriage bolts from hardware kit.
3.4 (See Figure 6) Trim the 1” flat bulb at the bottom of the contour
even with the bottom of the tractor floorboard.
3.5 Repeat for right side frame.
3.6 (See Figure 7) Check that 1” flat bulb on the front cowl assembly is
still pointing forward and attach the cowl assembly to left and right
side frames with 5/16” X 3/4” button head screws.
4. ROLL BAR BRACKETS
4.1 (See figure 8) Install roll bar bracket mounts to left and right rear
legs with 5/16” X 3/4” carriage bolts.
4.2 (See figure 8) Install roll bar brackets to the mounts with 5/16” X 1”
carriage bolts. NOTE: Carriage bolt heads should be on the bracket
side pointing toward the center of the tractor.
FIGURE 5
FIGURE 6
FIGURE 7
CABS/BLADES/ SPREADERS/ACCESSORIES
FIGURE 8
Right side viewed from
operators seat.
p. 4 of 8
Page 5
111 HIGGINS STREET, WORCESTER, MA 01606
MODEL: JOHN DEERE 2305, 2210 HARD SIDE & SOFT SIDE CABS
5. HARD SIDED REAR PANEL (Optional on soft sided cabs)
5.1 (See Figure 9) Tilt the tractor seat forward and have an assistant
help pass the rear panel through the front of the cab and position the
bottom of the panel against the base of the rear legs. Pivot the panel
up and into position against the rear legs being careful not to tear or
pull off the rubber gasket at the bottom of the panel.
5.2 Bolt the rear panel to the rear legs with four 5/16” X 3/4” button
head screws in the bottom four holes only. The top holes will be
used when bolting the roof on.
6. WINDSHIELD SUPPORT
6.1 (See Figure 10) Install the windshield support to the side frames
with the bent flange down. Install only the bottom two 5/16 x 1”
long button head screws. NOTE: The top holes will get fasteners
once the roof is installed. Align the edges of the windshield support
with the outside edges of the side frames and tighten bolts.
7. WINDSHIELD
7.1 (See Figure 11) With assistance, install the windshield to the wind-
shield support. Use four 5/16 x 1 3/4” long flat head screws and two
3/4” thick plastic spacer blocks placed between the plastic hinge and
the windshield support.
7.2 (See Figure 12) To install windshield bottom latches into the cowl
brackets, open windshield slightly. Grasp and squeeze the springloaded tabs and cradle latches into cowl brackets, aligning tab bosses with their respective mounting holes.
7.3 To close, grasp the windshield bottom edge and lift slightly while
pushing closed. Fully close latches. Align sides of windshield with
side frames and tighten hinges. HINGES ARE PLASTIC COMPONENTS. DO NOT OVER TIGHTEN. TORQUE TO 7 FT./LBS.
MAX.
FIGURE 9
FIGURE 10
FIGURE 11
CABS/BLADES/ SPREADERS/ACCESSORIES
FIGURE 12
p. 5 of 8
Page 6
111 HIGGINS STREET, WORCESTER, MA 01606
MODEL: JOHN DEERE 2305, 2210 HARD SIDE & SOFT SIDE CABS
8. ROOF
8.1 Use a Phillips head screwdriver or other pointed instrument to poke
holes in the roof headliner at each of the bolt holes. Puncture from
the headliner side to the outside.
8.2 (See fig. 13) Install roof with 5/16” button head screws using 1”
long screws as noted and 3/4” long screws elsewhere. If installing
the hard sided rear panel install a 3/4” long bolt in the center of the
rear flange.
9. REAR CURTAIN (SOFT SIDE ONLY)
9.1 Install rear curtain by snapping to the inside back vertical edge of
the roof.
9.2 (See Fig. 14) (NOTE: adhesive backed Velcro should be applied to
a clean, dry surface at room temperature.) Using the curtain as a
guide apply self adhesive hook Velcro, as needed, along the inside
of the rear legs and the corresponding line along the tractor. Attach rear curtain to newly applied Velcro strips.
10. FINISHING TOUCHES
10.1 Tighten bolts on front cowl assembly, windshield support and rear
legs, lining up the edges of the sheet metal with the outside corners
of the unitized frame tube. Tighten the bolts in the roof and rear
panel (if equipped). Next, tighten the bolts attaching the base of the
rear legs and seat belt holders to the roll bar followed by the floorboard bolts. Finally, tighten the roll bar mounts and brackets. Install
plastic nut covers on all the nuts on the inside of the cab as well as
the roll bar brackets.
10.2 Install doors onto hinges. Work the doors back and forth until the
hinges are completely seated. (NOTE: the hinges, inside latch, and
striker bolt can also be adjusted for proper engagement.)
1” long
HS ONLY
FIGURE 13
FIGURE 14
FIGURE 15
10.3 (For hard sided cabs only) (See Fig. 15) Install the gas spring to the frame and door with the small
piston end towards the door. Press the button on the compression fastener to lock the gas spring in
place.
10.4 Install the windshield wiper per instructions included with the wiring and hardware kits.
Care and Maintenance Instructions
Check and tighten hardware after 40 hours of operation. Periodically inspect and tighten hardware
for the remainder of the unit’s life.
Wash the painted surfaces of the unit with commercial automotive cleaning products.
Clean windows with glass cleaner.
Vinyl components should be washed with a mild solution of warm soapy water.
Clear vinyl can be easily scratched. Be careful cleaning frost or snow from windows. Do not roll
curtains in cold weather. The windows become stiff and may crack. Keep windows clean.
CABS/BLADES/ SPREADERS/ACCESSORIES
p. 6 of 8
Page 7
ROOF
QTY. P/N
YELLOW
*
HEADLINER
*
TRIM-LOK
3 SIDES
WINDSHIELD
QTY. P/N
COWL
GREEN
WINDSHIELD LATCH
*
MOUNTS
ROLL BAR
BRKT. MOUNTS
QTY. P/N
T-BLACK
JOHN DEERE 2305 & 2210 HARD SIDED CAB PARTS LIST
QTY. P/N
1 JD2210-01
*
1 JD2210-08
2 JD2210-11
* ARCH PSA
2 PCS. (INSIDE)
REFLECTORS
*
LOGO
*
1/2" WEATHER
SEAL (INSIDE)
WINDSHIELD
*
LATCHES
*
QTY. P/N
FRONT LEGS
GREEN
ROLL BAR
BRACKETS
T-BLACK
LEFT
RIGHT
* HEYCO PLUGS
* 1" FLAT BULB
QTY. P/N
HINGES
1 JD2210-05LA
1 JD2210-05RB
2 JD2210-12
1 JD2210-02
SEAM BULB
*
5/8"
SIDE
BULB
1/4" GRIP
* WEATHERSEAL
(INSIDE)
* ARCH PSA
2 PCS. (ALL 3
INSIDE SURFACES)
(BOTH PARTS)
REAR LEGS
QTY. P/N
GREEN
LEFT
RIGHT
WINDSHIELD
SUPPORT
T-BLACK
*
HEYCO PLUG
REAR PANEL
GREEN
QTY. P/N
QTY. P/N
1/2" WEATHER
*
SEAL (OUTSIDE)
9GL-22X26
W/ 5/8" SIDE
BULB w/ 1/4"
GRIP & 5
WINDOW
CLIPS
1 JD2210-03L
1 JD2210-03R
*WEATHERSEAL
1 JD4110-04
DECALS (INSIDE)
(SERIAL #, OPTIONS,
& R.O.P.S.)
1 JD2210-06
(INSIDE)
1/2" WEATHER
*
SEAL (INSIDE)
* HEYCO PLUGS
(5/16" & 7/8")
UNITIZED SIDE
FRAMES HARD CAB
T-BLACK
* 5/16-18
INSERTS
8/SIDE
RIGHT
* LH & RH HINGE
PINS & HINGE
PLATES
* 2" GRIT PAPER
*IN HOUSE APPLICATIONS
QTY.
LEFT
RIGHT11
LEFT
OUTSIDE EDGE
W/ 1/4" GRIP
HARD DOORS
P/N
JD2210AS-09L
JD2210AS-09R
* BALL STUD
* LATCH PIN
* HEATER
LABEL
(INSIDE)
* HINGE
SLEEVES
RIGHT
GREEN
* GRAB
HANDLE
* OUTSIDE
HANDLE
* 5/8" SIDE
BULB
CABS/BLADES/SPREADERS/ACCESSORIES
QTY.
LEFT 1
RIGHT 1
LEFT
P/N
JD2210AS-07L
JD2210AS-07R
* BALL STUD
* 1" HEYCO
PLUG
* 1" ROUND
BULB
* DOOR
LATCH
p. 7 of 8
Page 8
JOHN DEERE 2305 & 2210 SOFT SIDED CAB PARTS LIST
QTY. P/N
ROOF
QTY. P/N
YELLOW GREEN
*
HEADLINER
1 JD2210-01
*
TRIM-LOK
3 SIDES
REFLECTORS
*
LOGO
*
& 6 SNAPS
WINDSHIELD
QTY. P/N
COWL
GREEN
WINDSHIELD LATCH
*
MOUNTS
1 JD2210-08
*
1/2" WEATHER
SEAL (INSIDE)
ROLL BAR
BRACKET
QTY. P/N
MOUNTS
T-BLACK
2 JD2210-11
* ARCH PSA
2 PCS. (INSIDE)
WINDSHIELD
*
LATCHES
*
QTY. P/N
FRONT LEGS
GREEN
BRACKETS
T-BLACK
LEFT
RIGHT
* HEYCO PLUGS
* 1" FLAT BULB
QTY. P/N
HINGES
2 JD2210-12
1 JD2210-02
SEAM BULB
*
5/8"
SIDE
BULB
1/4" GRIP
1 JD2210-05LA
1 JD2210-05RB
* WEATHERSEAL
(INSIDE)
* ARCH PSA
2 PCS. (ALL 3
INSIDE SURFACES)
(BOTH PARTS)
REAR LEGS
QTY. P/N
LEFT
RIGHT
WINDSHIELD
SUPPORT
T-BLACK
*
HEYCO PLUG
REAR CURTAIN
YELLOW
VINYL
QTY. P/N
QTY. P/N
1 JD2210-03L
1 JD2210-03R
*WEATHERSEAL
(INSIDE)
1 JD4110-04
DECALS (INSIDE)
(SERIAL #, OPTIONS,
& R.O.P.S.)
1/2" WEATHER
*
SEAL (INSIDE)
1 JD2210-10
W/ 1/4" GRIP
UNITIZED SIDE
FRAMES SOFT CAB
T-BLACK
* 5/16-18
INSERTS
8/SIDE
RIGHT
* LH & RH HINGE
PINS & HINGE
PLATES
* 2" GRIT PAPER
QTY.
LEFT
RIGHT
LEFT
OUTSIDE EDGE
1
1
P/N
JD2210SS-09L
JD2210SS-09R
* LATCH PIN
* HEATER
LABEL
(INSIDE)
*IN HOUSE APPLICATIONS
CABS/BLADES/SPREADERS/ACCESSORIES
* HINGE
SLEEVES
RIGHT
LOGO
*
SOFT DOORS
YELLOW VINYL
BLACK POLY
* GRAB
HANDLE
* OUTSIDE
HANDLE
* 5/8" SIDE
BULB 1/4" GRIP
QTY. P/N
LEFT 1 JD2210SS-07L
RIGHT
LEFT
JD2210SS-07R1
* 1" HEYCO
PLUG
* DOOR
LATCH
p. 8 of 8
Loading...