CUMMINS ALLISON Universal JetScan 4161, Universal JetScan 4163, Universal JetScan 4166, Universal JetScan 4169 User Manual

Universal JetScan

®

Single

-Pocket Note Scanner

User

Guide

Safety Information, Power Specifications

• Voltage operating range: 105-240 VAC, automatic switching

• Frequency: 50/60 Hz

• Full load amps (FLA): 1A/.5A

• Electrical supply circuit: The customer must provide a single-phase, dedicated power line

that meets the machine’s power requirements. Use a properly grounded circuit breaker in
compliance with applicable local electrical code.

Environmental Operating Conditions

• Temperature: 60°F - 85°F (15°C - 29°C)

• Humidity: 30% to 70% (non-condensing)

Compliance Acknowledgments

• Laser: This equipment may contain Class 2 laser products and complies with FDA Radiation

Performance Standards, 21 CFR Subchapter 1 and the international laser safety standard IEC-

60825.1-2001-08.

• FCC: This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired
operation.

• Regulatory: CUL, CE

022-7661-00 – Rev. A

High voltage inside. Risk of electric shock.

Turn power

OFF

and unplug power cord from machine before cleaning.

Do not attempt repairs. Repairs must be made by authorized Cummins Allison
personnel.

Plug three-prong grounded plug (supplied) into properly grounded three-prong
outlet.

Read and understand all instructions before use.

Improper voltage levels can cause equipment malfunction, damage electrical

components, and void warranty.
Provide separate circuit serving only this device and follow listed power

requirements to ensure proper operation.
Provide power conditioning/stabilizing devices if necessary.

2

Table of Contents

SAFETY INFORMATION, POWER SPECIFICATIONS ................................................... 1

ENVIRONMENTAL OPERATING CONDITIONS ............................................................ 1

COMPLIANCE ACKNOWLEDGMENTS ......................................................................... 1

MACHINE DIAGRAM .................................................................................................... 3

DISPLAY/CONTROL-PANEL DIAGRAMS .................................................................... 4

MODELS 4161, 4163, 4166, 4169............................................................................. 4

VALUE KEY SETTINGS ....................................................................................................... 5

KEY NUMBERS DIAGRAM ................................................................................................. 5

KEY EXPLANATIONS ......................................................................................................... 5

THE BASICS ................................................................................................................. 7

ADJUSTABLE HOPPER....................................................................................................... 7

CHOOSING A COUNTRY ..................................................................................................... 7

THICKNESS ADJUSTMENT DIAL .......................................................................................... 8

OPERATING MODES ......................................................................................................... 8

Count ........................................................................................................................ 8

Mixed ....................................................................................................................... 8

Offsort ...................................................................................................................... 8

Sort ........................................................................................................................... 8

Stranger Detect ...................................................................................................... 8

HOW TO PROCESS NOTES.......................................................................................... 9

DAILY CLEANING PROCEDURES ............................................................................. 10

RECOMMENDED CLEANING MATERIALS .......................................................................... 10

DAILY CLEANING ........................................................................................................... 10

STOPPING CONDITIONS AND RECOVERY STEPS .................................................. 14

Single-Pocket Universal JetScan® Note Scanner

All Models

3

Machine Diagram

Stacker

wheels

Hopper

guides

Feeder plate

Stacker mirror

Function keys

Display

Function keys

Feed roller

Hopper

Thickness

adjustment dial

(behind hopper)

Stacker sensor

Feed roller

Stacker

Power switch

and power cord
on rear of unit

© 2014 Cummins-Allison Corp.

4

Display/Control-Panel Diagrams

Models 4161, 4163, 4166, 4169

Shown below are key legends as they appear on single-pocket Universal JetScan® note
scanner models 4161, 4163, 4166 and 4169.

Display Label

Description

Denomination

For offsort and stranger detect modes, the target denomination appears
under this label. For sort mode, the denomination that currently is being
sorted appears under this label.

Sub Total

The sub-batch total appears under this label.

Batch Count

The batch (strap) count appears under this label.

Mode

The selected operating mode appears above this label.

Total

The batch total appears above this label.

Batch Limit

The batch (strap) limit appears above this label.

Denomination Sub Total Batch Count

Mode Total Batch Limit

Clear Batch Start

Day All Batch End Sub

Mode Add Verify Unit CF Density Denom Set Batch End Tot

VAL 1 VAL 2 VAL 3 VAL 4 VAL 5 VAL 6 VAL 7 VAL 8 VAL 9

Single-Pocket Universal JetScan® Note Scanner

All Models

5

Value Key Settings

Single-pocket Universal JetScan value keys (VAL keys) represent note denominations that
have been pre-programmed for specific countries. The VAL 1 through VAL 9 keys are each
assigned to one denomination, from lowest to highest, by country.

Key Numbers Diagram

Positions of key numbers, which do not appear on the single-pocket Universal JetScan, are
shown below. Key numbers are referenced in some setup operations.

Key Explanations

Key

Description

Clear (Key 1)

This key is used when clearing day totals or batch (strap) counts and
reconciling sub-batch and batch totals.

Batch (Key 2)

This key is pressed after Clear to clear a denomination batch (strap)
count.

Start (Key 3)

This key is used to restart the machine after a stopping condition has
occurred.

Day (Key 4)

This key changes the screen to day totals and displays the grand total for
the day. It also can be pressed after

Clear

to clear day totals. The

Day key

also may be used to adjust processing speed. After holding down

Day

for
3 seconds, the machine’s speed may be set to LOW, MED or HI by
scrolling with the

Day key

.

Please contact a Cummins Allison representative to obtain the value key (VAL

key) layout for a particular country.

For more information on machine setup, please refer to the operating

instructions, which are packed with the machine.

Denomination Sub Total Batch Count

Mode Total Batch Limit

Key 1 Key 2 Key 3

Key 4 Key 5 Key 6

Key 7 Key 8 Key 9 Key 10 Key 11 Key 12 Key 13 Key 14 Key 15

VAL 1 VAL 2 VAL 3 VAL 4 VAL 5 VAL 6 VAL 7 VAL 8 VAL 9

© 2014 Cummins-Allison Corp.

6

Key

Description

All Batch (Key 5)

This key is used in conjunction with Clear to simultaneously clear batch
(strap) counts for all denominations.

End Sub (Key 6)

This key is used to clear sub-batches. It also can be pressed after Clear to
reconcile a sub-batch.

Mode (Key 7)

This key is used for setting an operating mode. Holding down the key for

2 - 3 seconds allows the user to select the country’s currency that will be

processed.

Add (Key 8)

This key is used for accumulating a batch total even after notes have been

removed from the stacker. It also is used to enable the sub-batch

function.

Verify

(Key 9)

This key is used to review a count suspected of being erroneous.

Unit (Key 10)

This key is used to toggle between value and piece count.

In count mode, the Unit key is locked ON for piece

counting only.

CF (Key 11)

This key is used to activate counterfeit detection and set sensitivity by
denomination.

Density

(Key 12)

This key is used for setting doubles-detection sensitivity by denomination.

Denom (Key 13)

This key is used to select the denomination appearing on the display
screen.

Set Batch (Key 14)

This key is used for setting a batch (strap) limit at any preset value (5, 10,

20, 25, 50, 75, 100 or infinity). This key also is used to set custom values,
such as 53 or 79. Holding down the key 2 - 3 seconds increases the value

by one.

End Tot (Key 15)

This key clears all batch and sub-batch totals. It also will clear all batch

(strap) counts and generate a print report, if these features have been
enabled. Holding down this key for 3 seconds allows access to USER

SETUP and DIAGNOSTICS without powering down the machine.

Denomination

Value Keys

Single-pocket Universal JetScan value keys (

VAL

keys) represent note

denominations that have been pre-programmed for specific countries. The

VAL 1

through

VAL 9

keys are each assigned to one denomination, from

lowest to highest, by country.

If these keys have been activated in USER SETUP, recovering from certain
stopping conditions is accomplished by simply pressing the key that
corresponds to the top note in the stacker. It will add that note amount to

the machine’s totals and restart the machine.

Please contact a Cummins Allison representative

to obtain the value key (

VAL

key) layout for a

particular country.

Single-Pocket Universal JetScan® Note Scanner

All Models

7

The Basics

Adjustable Hopper

The hopper is the area on top of the Universal JetScan where documents are placed for
processing. (See Machine Diagram.)

The hopper guides are adjustable and feature a series of numerical settings which correlate to
the width of documents.

When the desired country is selected, the required numerical setting for the hopper guides
will appear on the display.

By using the required numerical setting, there is less opportunity for documents to shift and
cause errors.

Choosing a Country

Hold down Mode for 2 - 3 seconds. Scroll through the available countries by pressing key
13 or key 14. Pressing Day toggles between two selected countries chosen in COUNTRY
TOGGLE. Press key 3 to return to normal operating mode.

Machine is auto-start capable. Feed rollers in hopper rotate inward.

Entanglement and drawing-in hazard.
Do not operate with exposed long hair, neckties, jewelry or loose

clothing.

To avoid an increase in no calls and feed errors, documents must be processed

at the required hopper-guide setting.

Denomination Sub Total Batch Count

ADJUST HOPPER

TO POSITION #2

Mode Total Batch Limit

When a new country is selected, sub-batch totals, batch totals and batch (strap)

counts are reset to zero.

Countries are selected at the time of purchase. To add more countries, contact
a Cummins Allison representative

.

© 2014 Cummins-Allison Corp.

8

Thickness Adjustment Dial

This gray dial, located on top of the Universal JetScan, adjusts the tightness of the feeder
through which notes pass during operation. The dial features a series of numbers, with 0
being center. Negative numbers, such as -1 and -2, appear to the left of 0. Positive numbers,
such as +1 and +2, appear to the right of 0.

Operating Modes

Universal JetScan has five basic operating modes for processing: count, mixed, offsort, sort
and stranger detect.

Count

• Display: COUNT
This mode counts any document that complies with document-size and density-setting

specifications. This mode only counts pieces; note scanning does not occur.

Mixed

• Display: MIXED, MIXFCE, MIXORT
This mode scans notes of all denominations (of one country) without presorting. It provides

the total count and value plus individual counts and values if desired.

Offsort

• Display: OFFSRT
This mode scans notes of all denominations (of one country) and stops for the target

denomination. The target denomination is selected by pressing Denom. A grand total is
provided.

Sort

• Display: SORT, SRTFCE, SRTORT

This mode scans notes of all denominations (of one country), and is best used – but is not
limited to – when notes are presorted by denomination and then stacked on top of each other.
The machine stops when a change in denomination is detected. A grand total is provided.

Stranger Detect

• Display: STRNGR, STRFCE, STRORT

This mode scans notes (of one country) for the target denomination, which is the first note
processed. The machine separates the target denomination from all other denominations and
stops when a stranger – which is any note other than the target denomination – is detected. A
grand total is provided; strangers are not included in the grand total.

For normal feeding, always start at zero.

By turning the thickness adjustment dial to the right and to access negative
numbers, the rollers are made tighter. This might be done when excessive
doubles or chains occur.

By turning the thickness adjustment dial to the left and to access positive
numbers, the rollers are made looser, allowing the notes to flow through the
Universal JetScan easier.

Single-Pocket Universal JetScan® Note Scanner

All Models

9

How to Process Notes

1. Turn the Universal JetScan ON. The switch is located in the lower-right rear corner when

facing the front of the machine.

When Universal JetScan is turned ON:

• Some components require time to warm up. A “WARMING UP” message will appear

on the display until the Universal JetScan is ready for processing.

• It will default to the mode it was in when last turned OFF.

2. Select a country’s currency. Press and hold Mode until country names appear. Then
repeatedly press Denom to scroll through available countries. Stop on the desired country
and press Start.

3. Adjust the hopper guides for the selected country’s currency.

4. Turn the thickness-adjustment dial to 0.

5. Repeatedly press Mode to select the operating mode. (See Operating Modes for more
information.)

6. Organize and straighten notes.

7. Place notes in the hopper; Universal JetScan automatically will begin processing and
automatically will stop when all notes have been processed.

High voltage inside. Risk of electric shock.

Turn power

OFF

and unplug power cord from machine before cleaning.

Do not attempt repairs. Repairs must be made by authorized Cummins Allison
personnel.

Plug three-prong grounded plug (supplied) into properly grounded three-prong
outlet.

Read and understand all instructions before use.

To avoid an increase in no calls and feed errors, documents must be processed at

the required hopper-guide setting.

Machine is auto-start capable. Feed rollers in hopper rotate inward.

Entanglement and drawing-in hazard.
Do not operate with exposed long hair, neckties, jewelry or loose

clothing.

© 2014 Cummins-Allison Corp.

10

Daily Cleaning Procedures

Daily cleaning of the Universal JetScan note scanner is recommended to ensure maximum
productivity and reliability, especially for high-volume applications, as well as for those processing
highly circulated (dirty) notes.

Recommended Cleaning Materials

• Simple Green Safety Towels. (Part number: 022-2118-00.) A pre-moistened microfiber

towel also may be used. If using Simple Green concentrate, dilute to: 30 ml (1 ounce) of
Simple Green per 240 ml (8 ounces) of water. For a material-safety-data sheet, see

simplegreen.com.

• Microfiber towels. (Part number: 022-2223-00.)

• A clean, soft eraser. (Part number: 022-1695-00.)

• Vacuum (purchase locally).

Daily Cleaning

Simple Green, the recommended cleaning agent, can be an eye

irritant. Avoid eye contact.
If eye contact occurs, flush eye(s) with cool water for 5 minutes –

remove contact lenses if present – continue flushing eye(s) with cool
water for 15 more minutes. If irritation persists, consult physician.

Individuals with sensitive skin should rinse hands after using.

High voltage inside. Risk of electric shock.

Turn power

OFF

and unplug power cord from machine before

cleaning.

To avoid machine/component damage and potential voiding of

existing warranty, follow these procedures:
Only use specified tools for cleaning machine. Never use metal tools.
If using Simple Green concentrate, dilute to: 30 ml (1 ounce) of

Simple Green per 240 ml (8 ounces) of water.
Never use cleaners containing ammonia. Ammonia may remove

labels from machine.
Never spray cleaners directly on machine components.

Single-Pocket Universal JetScan® Note Scanner

All Models

11

1.

Turn power

OFF

(rocker panel to 0).

2.

Disconnect power cord from the rear of the Universal
JetScan.

3.

Lift adjustable hopper to the upright position.

4.

Remove feeder plate as shown below.

5.

Use a microfiber towel to clean the black start sensor at the
top, middle of the feeder plate, as identified at left.

6.

Use a Simple Green Safety Towel to remove dirt buildup from the upper and lower aluminum
rollers. To reach all exposed surfaces, rotate the large, black feed rollers forward (direction of
note flow).

Rotating the large, black feed rollers will rotate all other shafts and
rollers in the machine. These rollers can be rotated in either
direction by using fingers. Generally, the top of these rollers should
be rotated forward (direction of note flow), so any dirt or stray
material is moved out of the unit.

If there is heavy buildup on the aluminum rollers, remove it
with a clean, soft eraser as shown.

© 2014 Cummins-Allison Corp.

12

7.

Use a Simple Green Safety Towel to clean all rubber sections
of the large, black feed rollers. Rotate the rollers.

Also clean the flat, center rubber-drive tire, as identified at
left.

8.

Use a microfiber towel or vacuum to remove any remaining
dust in the bottom stacker.

9.

Use a microfiber towel to clean the stacker-sensor lens
located in the stacker tray between the two gray stacker
wheels.

Clean the stacker mirror located directly across from the
stacker-sensor lens.

Stacker-sensor lens

Stacker mirror

10.

Replace feeder plate. Insert curved edge of feeder plate first.
Gently press down on feeder plate until it snaps into position.

Curved edge

11.

Clean exterior surfaces as necessary with a Simple Green
Safety Towel.

12.

Return hopper to the operating position.

Single-Pocket Universal JetScan® Note Scanner

All Models

13

13.

Carefully reconnect power cord.

14.

Turn power ON (rocker panel to I).

15.

Perform a test run with some notes.

© 2014 Cummins-Allison Corp.

14

Stopping Conditions and Recovery Steps

Screens are listed alphabetically.

Denomination Sub Total

Batch Count

CHAIN DETECTED

Mode Total Batch Limit

Condition

Action

Universal JetScan may have

processed two or more notes as
one.

Remove all notes from the stacker and place them on the hopper. Press
Start

. If an alarm repeatedly occurs, adjust the gray thickness dial located

on top of the machine behind the hopper extension. Rotate in the negative

(-)

direction as indicated by the numbers on the front of the thickness dial.

Denomination Sub Total Batch Count

DENOMINATION CHANGE

Mode Total Batch Limit

Condition

Action

Universal JetScan has identified

a note that is different than
those it has been processing
while using sort modes.

This first note of the different
denomination is the top note
in the stacker.

Remove all notes from the stacker. Separate the top note from the

remaining notes. Put the top note in the location for its denomination. Put
all the other notes (they are all the same) in the location for their
denomination.

Universal JetScan automatically will restart.

Denomination Sub Total Batch Count

DOUBLE DETECTED

Mode Total Batch Limit

Condition

Action

Universal JetScan may have

processed two or more notes as
one.

Remove all notes from the stacker and put them on the hopper. Press Start.

If an alarm repeatedly occurs, adjust the gray thickness dial on top of the
machine behind the hopper extension. Rotate in the negative

(-)

direction as

indicated by the numbers on the front of the thickness dial.

This screen could

show any of these
messages:

• CHAIN DETECTED

• CHAIN DETECTED*

Single-Pocket Universal JetScan® Note Scanner

All Models

15

Denomination Sub Total Batch Count

FACING ERROR

Mode Total Batch Limit

Condition

Action

Universal JetScan has identified

a note that is incorrectly faced.

Correctly face the note, return it to the hopper, and press Start.

Denomination Sub Total Batch Count

JAM

REMOVE HOPPER TRAY

Mode Total Batch Limit

Do not use tools or metal devices to remove jammed notes from paper path.

Use of tools or metal devices could cause machine damage and void existing
warranty.

For proper removal of jammed notes, see Action, Step 2.

Condition

Action, Step 1

Notes or possibly foreign

material are jammed in the
paper path and must be
removed.

A. Remove all notes from the top hopper and bottom stacker.

When notes are removed from the bottom stacker, the display will show:

<CLEAR>=FWD

B. Lift hopper to the upright position.

C. Remove feeder plate by lifting
with fingers in the two depressions.

© 2014 Cummins-Allison Corp.

16

Action, Step 2

Feed rollers in hopper rotate. Entanglement and drawing-in hazard.
Keep exposed long hair, neckties, jewelry and loose clothing away from

feed rollers.

DO NOT PRESS ANY KEY

while manually rotating feed rollers.

Next either:

• Move jammed notes forward/back by manually rotating the large, black feed rollers.

Rotating the large, black feed rollers will rotate all other shafts and rollers in

the machine. These rollers can be rotated in either direction by using fingers.
Generally, the top of these rollers should be rotated forward (direction of note
flow), so any dirt or stray material is moved out of the unit.

• Press

Clear

to slowly move the feeder forward.

Remove all jammed notes and foreign material.

Action, Step 3

Raise “T” handles

If the jam remains in the paper path, then raise

the two red, plastic “T” handles at the same time
and hook them onto the metal shaft.

Then either:

• Move jammed notes forward/back by
manually rotating the large, black feed
rollers.

• Press

Clear

to slowly move the feeder

forward

.

Remove all jammed notes and foreign material.

When finished, unhook the two red, plastic “T”
handles from the metal shaft and lower them at
the same time.

Lower “T” handles

Action, Step 4

Replace feeder plate. Insert curved edge of feeder plate first. Gently press down

on feeder plate until it snaps into position.

Curved edge

Single-Pocket Universal JetScan® Note Scanner

All Models

17

These two screens will sequentially flash:

Action, Step 5

Return hopper to the operating position.

Press

Start

.

Rerun all notes that were in the top hopper and bottom stacker at the time of
the jam.

NO CALL

CHECK NOTE

PRESS KEY

Condition

Action

Universal JetScan cannot
recognize the denomination of a
note and has stopped. This
no call note is the top note in
the stacker. This note has not
been included in the count.

Inspect the top note in the stacker to determine the correct denomination.
Do not

remove all notes from the stacker.

Then either:

• Leave the note in the stacker and press the appropriate

denomination

value key (VAL key)

to add the note to the total.

• Reprocess the note by returning it to the hopper and pressing

Start

.

Denomination Sub Total Batch Count

ORIENTATION ERROR

Mode Total Batch Limit

Condition

Action

Universal JetScan has identified

a note that is incorrectly
oriented.

Correctly orient the note and return it to the hopper and press Start.

© 2014 Cummins-Allison Corp.

18

Denomination Sub Total Batch Count

REMOVE STRANGER

Mode Total Batch Limit

Condition

Action

Universal JetScan has detected

a note of a different
denomination from those being
counted and has stopped. This
stranger note is the top note in
the stacker. This note has not
been included in the count.

Remove the top note in the stacker and press Start.

Denomination Sub Total Batch Count

STRAP LIMIT

100 PIECES USD 100

Mode Total Batch Limit

Condition

Action

The number of notes in the

stacker has reached the preset
batch (strap) limit.

Remove the notes from the stacker.

Universal JetScan automatically will continue processing if additional notes
remain in the hopper.

Single-Pocket Universal JetScan® Note Scanner

All Models

19

These two screens will sequentially flash:

Code

Possible Causes

MG, ML, MR, Z1, Z2

• Incorrect-ink error

• Worn note

UV

• Incorrect note paper

• Soiled note

•

Taped note

FL

• Incorrect note paper

• Machine-washed note

• Taped note

TH*

•

Thread error

* This code only appears on past models equipped with a thread sensor.

SUSPECT DOCUMENT

ML

CHECK NOTE

PRESS KEY

Condition

Action

Universal JetScan sensors have

detected a possible counterfeit
note. Universal JetScan has
stopped with this note as the top
note in the stacker. This note
has not been included in the
count.

Inspect the top note in the stacker. Next there are three options:

• If the note is deemed counterfeit, place it aside and press

Start

. It will not

be part of the count.

• If the note is deemed genuine, return it to the stacker and press the
appropriate

denomination value key (VAL key)

. Universal JetScan will

restart, and this note will be added to the count.

• Reprocess the note by returning it to the hopper and pressing

Start

.

This line could show

several different
suspect-document
codes. For details,
refer to the code
chart below.

© 2014 Cummins-Allison Corp.

20

These four screens will sequentially flash:

These three screens will sequentially flash:

WARNING – BOTH DOUBLES

SENSORS ARE FAULTY

ENSURE THAT SENSORS ARE

CLEAR OF PAPER AND DUST

CALL SERVICE IF

PROBLEM PERSISTS

PRESS <START> KEY

TO CONTINUE

Condition

Action

Universal JetScan is indicating

there possibly is a problem with
the right, left or both doubles
sensors.

Press Start to attempt continued operation. If the alarm occurs again, clean

the machine by following the daily cleaning procedures. If the message
continues to appear,

call a local Cummins Allison service representative

.

WARNING – UV BULB

INTENSITY OUT OF RANGE

UV DETECTION

IS UNRELIABLE

PRESS <START> KEY

TO CONTINUE

Condition

Action

Universal JetScan is indicating

there is a possible problem with
the ultraviolet (UV) bulb
(“BECOMING WEAK,” “INTENSITY
OUT OF RANGE” or
“UNRELIABLE”).

Press Start to continue operation. If the machine is not equipped with

ultraviolet (UV), be sure to turn the feature off in USER SETUP. If the
message continues to appear,

contact a local Cummins Allison service

representative

.

Single-Pocket Universal JetScan® Note Scanner

All Models

Headquarters

852 Feehanville Drive
Mt. Prospect, IL 60056 USA
800 786 5528

cumminsallison.com

Australia

P.O. Box 7051
Silverwater,

NSW 2128

Australia
02 96

48 6661

cumminsallison.com.au

Canada

3350 Ridgeway Drive, Unit 3
Mississauga

, Ontario

L5L 5Z9
Canada
905 814 6184

cumminsallison.ca

France

Parc

Des Nations-Paris Nord 2

385 Rue de la Belle Etoile
95974 Roissy, France
33 148 196 160

cumminsallison.fr

Germany

ITS Center Unit 29
Arnold

Sommerfeld

Ring 2
D

-52499 Baesweiler,

Germany
49 2401 805

252

cumminsallison.de

United Kingdom

William

H. Klotz House

Colonnade Point,
Central Boulevard
Prologis Park
Coventry

, CV6 4BU

U

nited Kingdom

44 2476 339 810

cumminsallison.co.uk

©

2014 Cummins-Allison Corp. All rig hts reserved.

All trademarks remain the property of their respective owners.

Cummins

-Allison Corp. has endeavored to make the content of this document accurate and complete, but this information is subject to correction or ch ange without prior no tice.

This manual conta ins proprietary information of Cummins

-Allison Corp. It is intended solely for the information and use of p arties authorized by Cummins Allison to mainta in

the equipment described herein. Such proprietary information may not be used, repro

duced, or disclosed to any other parties for any other purpose without express written

permission of Cummins Allison. 022-7661-00 Rev. A