Page 1
Simple Green, the recommended cleaning agent, can be an eye irritant. Avoid eye contact.
High voltage inside. Risk of electric shock.
OFF
To avoid machine/component damage and potential voiding of existing warranty, follow these
OFF
®
JetCount currency counter cleaning procedures
Daily cleaning of the JetCount® currency counter is recommended to ensure maximum productivity and reliability,
especially for high-volume applications, as well as for those processing highly circulated (dirty) notes.
Recommended cleaning materials
If eye contact occurs, flush eye(s) with cool water for 5 minutes – remove contact lenses if
present – continue flushing eye(s) with cool water for 15 more minutes. If irritation persists,
consult physician.
Individuals with sensitive skin should rinse hands after using.
■ Simple Green Safety Towels. (Part number: 022-2118-00.)
A pre-moistened microfiber towel also may be used. If using Simple Green concentrate, dilute to: 1 ounce of
Simple Green per 8 ounces of water. For a material-safety-data sheet, see simplegreen.com.
■ Microfiber towels. (Part number: 022-2223-00.)
■ A clean, soft eraser. (Part number: 022-1695-00.)
■ Vacuum. (Part number, standard vacuum: 022-1959-00; part number. heavy-duty vacuum: 022-1308-00.)
Daily cleaning
1.
2.
Turn power
procedures:
Only use specified tools for cleaning machine. Never use metal tools.
If using Simple Green concentrate, dilute to: 1 ounce of Simple Green per 8 ounces of water.
Never use cleaners containing ammonia.
Never spray cleaners directly on machine components.
and unplug power cord from machine before cleaning.
Turn power
Disconnect power cord from the back of the JetCount.
(rocker panel to 0).
800 786 5528 Page 1 of 3 cumminsallison.com
Page 2
3.
Rotating the large, black feed rollers will rotate all other shafts and rollers in the machine. These
If there is heavy buildup on the aluminum rollers, remove it with a clean, soft eraser
4.
Remove feeder plate as shown below.
Remove hopper guide.
5.
Use a Simple Green Safety Towel to remove dirt buildup from the upper and lower aluminum rollers. To reach all exposed
surfaces, rotate the large, black feed rollers forward (direction of note flow).
Use a microfiber towel to clean the black start sensor at the top, middle of the feeder
plate, as identified at left.
rollers can be rotated in either direction by using fingers. Generally, the top of these rollers should
be rotated forward (direction of note flow), so any dirt or stray material is moved out of the unit.
6.
as shown.
Use a Simple Green Safety Towel to clean all rubber sections of the large, black feed
7.
rollers. Rotate the rollers.
Also clean the flat, center rubber-drive tire, as identified at left.
8.
800 786 5528 Page 2 of 3 cumminsallison.com
Use a microfiber towel or vacuum to remove any remaining dust
in the bottom stacker.
Page 3
9.
Use a microfiber towel to clean the stacker-sensor lens located in the stacker tray
Stacker-sensor lens
Stacker mirror
10.
between the two gray stacker wheels.
Clean the stacker mirror located directly across from the stacker- sensor lens.
Replace feeder plate. Insert curved edge of feeder plate first. Gently press down on
feeder plate until it snaps into position.
Curved edge
11.
12.
13.
Clean exterior surfaces as necessary with a Simple Green Safety Towel.
Replace hopper guide.
Carefully reconnect power cord.
14.
15.
Perform a test run with some notes.
800 786 5528 Page 3 of 3 cumminsallison.com
Turn power ON (rocker panel to I).
© 2018 Cummins-Allison Corp. JetCount.7200.Rev.D
Loading...