CUMMINS HDKCC, HDKCD Operator's Manual

Page 1
Operator Manual
Commercial Mobile Generator Set
HDKCC (Spec AC) HDKCD (Spec AC)
English Original Instructions 112009 9810174 (Issue 5)
Page 2
California
Proposition 65 Warning
Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.
Page 3
Table of Contents
SECTION PAGE
Table of Contents i. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAFETY PRECAUTIONS iii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. INTRODUCTION 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About this Manual 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nameplate 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to Obtain Service 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
noise 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electromagnetic compatibility 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Emissions 1-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical Genset 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. OPERATION 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Fuel 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Coolant 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Engine Oil 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting Batteries 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Panel 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Control Panels 2-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pre-Start Checks 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Priming the Fuel System 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Starting 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Stopping 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Starting and Stopping 2-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading the Genset 2-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resetting Circuit Breakers 2-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to Utility Power 2-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating in Cold Weather 2-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating in Hot Weather 2-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating at High Altitude 2-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating in Dusty Environments 2-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Breaking In a New Engine 2-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exercising the Genset 2-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storing the Genset 2-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3. PERIODIC MAINTENANCE 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
i
Page 4
General Inspection 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking Engine Oil Level 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing Engine Oil and Oil Filter 3-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintaining the Battery and Battery Connections 3-6. . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the Air Filter Element 3-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the Fuel Filter 3-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintaining the Coolant System 3-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. TROUBLESHOOTING 4-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting With Table 4-1 4-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fault Code Blinking 4-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restoring Fault Code Blinking 4-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. SPECIFICATIONS 5-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6. MAINTENANCE RECORD 6-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii
Page 5
SAFETY PRECAUTIONS
Thoroughly read the OPERATOR’S MANUAL before operating the genset. Safe operation and top performance can only be obtained when equipment is operated and maintained proper­ly.
Only trained and experienced service person­nel with knowledge of fuels, electricity, and ma­chinery hazards shall remove, dismantle and dispose of the generator set. See service manu­al.
The following symbols in this manual alert you to potential hazards to the operator, service person and equipment.
DANGER
which you must take steps to prevent severe personal injury or death, as when you are in the vicinity of High Voltage equipment.
WARNING
safe practice that can result in severe personal injury or death.
CAUTION
safe practice that can result in personal injury or equipment damage.
Electricity, fuel, exhaust, moving parts and batter­ies present hazards which can result in severe per­sonal injury or death.
Used to alert you to a leathal hazard
Used to alert you to a hazard or un-
Used to alert you to a hazard or un-
GENERAL PRECAUTIONS
S Keep children away from the genset.
S Do not use evaporative starting fluids. They
are highly explosive.
S To prevent accidental or remote starting while
working on the genset, disconnect the nega­tive () battery cable at the battery.
S Let the engine cool down before removing the
coolant pressure cap or opening the coolant drain. Hot coolant under pressure can spray out and cause severe burns.
S Keep the genset and its compartment clean.
Excess oil and oily rags can catch fire. Dirt and gear stowed in the compartment can restrict cooling air.
S Make sure all fasteners are secure and
torqued properly.
S Do not work on the genset when mentally or
physically fatigued or after consuming alcohol or drugs.
S You must be trained and experienced to make
adjustments while the genset is running—hot, moving or electrically live parts can cause se­vere personal injury or death.
S Used engine oil has been identified by some
U. S. state and federal agencies as causing cancer or reproductive toxicity. Do not ingest, inhale, or contact used oil or its vapors.
S Ethylene glycol, used as engine antifreeze, is
toxic to humans and animals. Clean up spills and dispose of used engine coolant in accor­dance with local environmental regulations.
S Keep multi-class ABC fire extinguishers
handy. Class A fires involve ordinary combus­tible materials such as wood and cloth; Class B fires, combustible and flammable liquid fuels and gaseous fuels; Class C fires, live electrical equipment. (ref. NFPA No. 10)
S Genset installation and operation must comply
with all applicable local, state and federal codes and regulations.
GENERATOR VOLTAGE IS DEADLY
S Disable the automatic genset starting feature
of an inverter-charger or other automatic start­ing device before servicing the genset.
S Generator electrical output connections must
be made by a trained and experienced electri­cian in accordance with applicable codes.
WARNING
and shore power can lead to electrocution of utility line workers, eqiupment damage and fire. Use an approved switching device to prevent interconnections.
S Use caution when working on live electrical
equipment. Remove jewelry, make sure cloth­ing and shoes are dry, stand on a dry wooden platform or rubber insulating mat and use tools with insulated handles.
Interconnecting the gnerator set
iii
Page 6
ENGINE EXHAUST IS DEADLY
S Inspect for exhaust leaks at every startup and
after every eight hours of running.
S Learn the symptoms of carbon monoxide poi-
soning in the Operator’s Manual.
S Never sleep in the vehicle while the genset is
running unless the vehicle is equipped with a working carbon monoxide detector.
S Do not operate the genset when the vehicle is
in a confined space, such as a garage.
S Disable the automatic genset starting feature
of an inverter-charger or other automatic start­ing device before storing the vehicle or parking it in a garage or other confined space.
S The exhaust system must be installed in accor-
dance with the genset Installation Manual.
S Engine cooling air must not be used for heating
working or living spaces or compartments.
S Do not wear loose clothing or jewelry near
moving parts such as PTO shafts, fans, belts and pulleys.
S Keep hands away from moving parts.
S Keep guards in place over fans, belts, pulleys,
and other moving parts.
FLAMMABLE VAPOR CAN CAUSE A
DIESEL ENGINE TO OVERSPEED
WARNING
genset where a flammable vapor environment can be created by fuel spill, leak, etc.
Flammable vapor can cause a diesel engine to overspeed and become difficult to stop, resulting in possible fire, explosion, severe personal injury and death. The owners and operators of the genset are solely responsible for operating the genset safely.
Do not operate a diesel-powered
DIESEL FUEL IS COMBUSTIBLE
S Do not smoke or turn electrical switches ON or
OFF where fuel fumes are present or in areas sharing ventilation with fuel tanks or equip­ment. Keep flames, sparks, pilot lights, arc­producing equipment and all other sources of ignition well away.
S Fuel lines must be secured, free of leaks and
separated or shielded from electrical wiring.
BATTERY GAS IS EXPLOSIVE
S Wear splashproof safety glasses.
S Do not smoke or permit flames or sparks to oc-
cur neat the battery at any time.
S To reduce arcing when disconnecting or recon-
necting battery cables, always disconnect the negative () battery cable first and reconnect it last.
MOVING PARTS CAN CAUSE SEVERE
PERSONAL INJURY OR DEATH
S Disable the automatic genset starting feature
of an inverter-charger or other automatic start­ing device before servicing the genset.
THE HAZARDS OF CARBON MONOXIDE
Enginedriven generators can produce harmful levels of carbon monoxide that can injure or kill you. The nature of boating is such that you can be harmed by this poisonous gas despite good gener­ator set maintenance and proper ventilation.
ONLY YOU CAN PROTECT YOURSELF
FROM CO POISONING!
S Watch constantly for swimmers when the gen-
erator set is running.
S Make sure exhaust cannot get under the deck,
between hulls or enter the living quarters through a window, vent or door.
S Make sure all CO detectors and audible alarms
are working properly.
S Pay attention to the signs of CO poisoning.
S Check the exhaust system for corrosion, ob-
struction and leaks each time you start the generator set and every eight hours if you run it continuously.
Mobile-8
iv
Page 7
SUBSTANCE HAZARDOUS TO HEALTH
PROTECTIVE MEASURES
Generator sets use substances, and emit and create wastes that can cause health risks. Genera­tor set operators must use appropriate personal protective equipment (such as clothing, gloves, protective glasses/goggles, and respiration equip­ment) when exposed to fuel, oil, coolant, wet batter­ies, grease, cleaning agents, or other substances exposed to lungs, eyes, or skin. use appropriate containers for transport, storage, and disposal of waste substances. Follow local regulations for dis­posal and recycling.
ANTIFREEZE (FLEETGUARD ES
COMPLEAT/EG PREMIX)
This antifreeze is also know as an ethylene glycol based coolant; summer coolant; coolant additive. It is purple coloured, viscous liquid, with a mild chemi­cal odour, is soluble in water and harmful. It con­tains ethylene glycol, and diethylene glycol. Ethyl­ene glycol is a potentially hazardous constituent.
The substance has a boiling point of 107° C, and a flash point of 121° C.
It is used as an engine coolant additive, and can be found in engine cooling systems, and head ex­changers. Installers, operators and maintainers are likely to encounter this substance.
HAZARDOUS REACTIONS
Ethylene glycol is combustible when exposed to heat or flame and can react vigorously with oxi­dants. Moderate explosive hazard in form of vapour when exposed to heat or flame. Hazardous prod­ucts resulting from combustion or decomposition include carbon monoxide, carbon dioxide and acrid smoke. Selfcontained breathing apparatus must be worn in the event of fume build up.
Avoid strong oxidizing agents incompatible with sulfuric acid, nitric acid, caustics and aliphatic amines.
It may cause neurological signs and symptoms, and kidney damage. It is also a skin and eye irritant.
Very toxic in particulate form upon inhalation. Harmful if swallowed, lethal dose for humans re­ported to be 100ml.
Refrain from eating, drinking or smoking when us­ing the product. Adopt a high standard of personal hygiene. In case of skin contact, wash immediately with soap and water.
Ensure good ventilation and avoid heat sources. Avoid breathing mist, if there is a risk of vapour, or particulate, use a suitable organic vapour mask.
Eye protection, gloves, overalls, impervious apron should be used. Avoid contamination inside the gloves. If overalls become contaminated, discon­tinue use and clean thoroughly.
STORAGE/TRANSPORT
Store and transport only in correctly marked con­tainers. Keep containers closed when not in use. Keep cool, out of sunlight, away for naked flames and strong acids, do not freeze. Store well away from foodstuffs and drinking water. Take special care to avoid discharge into drains, sewers and wa­tercourses.
Contain leak/spill with sand, earth or noncombus­tible, absorbent material to prevent entry of sub­stance into drainage/sewerage system, water courses and land. Eliminate all ignition sources, use plastic shovel to transfer to suitable container and dispose of unwanted or absorbed substance through and authorised contractor to a licensed site.
EMERGENCY ACTION
S Fire
Extinguishing media: CO foam, dry powder, or water spray. Fire fighters to use self contained breathing apparatus. Keep fire exposed containers cool. Prevent runoff from entering waterways, drains and drinking water supplies.
S ngestion
Toxic by ingestion. If swallowed induce vomit­ing only control centre. Delayed treatment may result in fatality.
S Inhalation (of vapour)
Remove from further exposure. In case of ir­ritation to lungs or throat, seek medical advice.
S Aspiration (inhalation of liquid)
Obtain immediate medical assistance.
S Eyes
Flush copiously with water or preferably eye
under the advice of a Doctor or poison
alcohol resistant
2,
v
Page 8
wash solution for at least five minutes. Seek medical advice.
S Skin
Wash thoroughly with soap and water, and seek medical attention if irritation develops. Change clothing if necessary and wash before reuse.
S Spillage
Soakup using an absorbent material and dis­pose of this as directed under Storage/Trans­port (Section 5.1.3)
GAS OIL
This product is also known as Red Diesel, Fuel Oil, and type A1 or A2. It can be pale red or a clear liquid with a characteristic mild odour. It contains catalyti­cally cracked oil, petroleum distillates, quinizarin, and gas oil maker dye red. The catalytically cracked oil and petroleum distillates are potentially hazard­ous constituents.
The substance has an initial boiling point of 180°C, a flash point greater than 56°C, and a vapour pres­sure less than 0.7mm Hg at 20°C and has negligible solubility in water.
It is used as a fuel for offroad diesel powered ve­hicles and stationary engines, and can be found in fuel tanks, pipes and injection systems. The sub­stance should not be used for any other purpose without contacting the manufacturer or supplier. In­stallers, operators and maintainers are likely to en­counter this substance.
HAZARDOUS REACTIONS
This liquid is flammable. Avoid smoking, heat sources, such as welding and naked flames, sparks and static electricity buildup. Thermal de­composition products are hazardous, containing
, NOX and SOX compounds.
CO
X
The vapour is explosive. High vapour concentra­tions can cause respiratory irritation, dizziness, nausea, and loss of consciousness. Excessive and prolonged exposure to the mist can cause chronic inflammatory reaction of the lungs and form of pul­monary fibrosis.
Avoid strong oxidising agents, e.g. chlorates which may be use in agriculture.
Gas oil is slightly irritating to the skin and has a de fatting action. Toxicity following single exposure to
high level of gas oil is of low order. Prolonged, re­peated skin contact may defat the skin resulting in possible skin irritation and dermatitis. In some cases warty, cancerous growths have occurred.
PROTECTIVE MEASURES
Ensure good ventilation and avoid heat sources. Observance of good housekeeping rules will en­sure general safety. Do not smoke. Avoid breathing mist.
When working on, or testing, injection equipment, special care is required to avoid perforation of skin by high pressure fuel. Use eye protection in the event of suspected high pressure leak.
Adopt a high standard of personal hygiene. In the case of skin contact, wash well with soap and water.
Use glove and overalls, and eye protection goggles if there is a risk of splashing. Use oil impervious gloves and avoid contamination inside the gloves. If overalls become contaminated, discontinue use and clean thoroughly. Contaminated clothing should be removed, soaked with water, and laun­dered before re−use.
No special respiratory precautions are necessary in normal use.
DO NOT use as a solvent for removing dirt/grease etc, from skin.
STORAGE/TRANSPORT
Store and transport only in correctly marked con­tainers. Keep containers closed when not in use. Keep cool, out of sunlight and away from naked flames. Electrical continuity is required between the transport and storage vessels during product trans­fer.
Contain leak/spill with sand, earth or other suitable material, and prevent entry of substance into drain­age/sewerage system, watercourses and land. Dispose of unwanted or absorbed substance through an authorised contractor to a licensed site.
Inform local and fire authorities should the product reach waterways, drains etc.
EMERGENCY ACTION
S Fire
Extinguishing media: Large fire Foam/water fog. Never use water jet.
vi
Page 9
Small fire foam/dry powder, AAAF, CO2, sand, earth. Avoid making sparks. Fire fighters to use self contained breathing apparatus. Keep fire ex­posed containers cool, using water fog/spray. Prevent runoff from entering waterway, drains and drinking water supplies.
S Ingestion
Do not induce vomiting. Wash the mouth out with water, and send to hospital immediately.
lubrication oil for use in wide range of diesel en­gines operating under severe conditions. Installers, operators and maintainers are likely to encounter this product.
HAZARDOUS REACTIONS
This product is stable although slightly re−active with oxidising agents. Results of decomposition are carbon oxides (CO, CO
) and water.
2
S Inhalation (of vapour)
Remove from further exposure. Obtain medi­cal assistance immediately.
S Aspiration (inhalation of liquid)
If, following ingestion of gas oil, vomiting oc­curs, there is danger of aspiration into the lungs. This would cause intense local irritation and chemical pneumonitis that can be fatal. Obtain immediate medical assistance.
S Eyes
Irrigate copiously with water or preferably eye wash solution for at least five minutes. If irrita­tion persists seek medical advice.
S Skin
Wash thoroughly with soap and water. Change clothing if necessary. If high pressure injection has occurred prompt surgical attention is required.
S Spillage
Absorb using sand, earth or other suitable ma­terial. Dispose of unwanted or absorbed flam­mable material as directed under Storage/ Transport (Section 5.7.3).
LUBRICATION OIL PREMIUM BLUE E
15W40
Also known as oil, lube oil, sump oil, new oil is dark, viscous liquid with a slight, characteristic odour. The base oil contains: distillates (petroleum), sol­ventdewaxed heavy paraffinic. It is not classified as dangerous according to Directive 1999/45/EC and its amendments, and is not classified accord­ing to the EU regulations.
It has a boiling point greater than 150°C, a flash point Open Cup of 220°C (Cleveland), and is insol­uble in cold water.
It is used in engine lubricant oil systems, sump pan and filters, makeup tanks and piping systems as a
Although harmful if swallowed or aspirated (breathed in), repeated or prolonged exposure is not known to aggravate medical conditions.
Used oil may contain harmful combustion byprod­ucts and unburnt fuel that will cause skin reactions as detailed for fuel. Particular care must be taken if oil form a severely overheated engine is handled use impervious gloves, lab coat and safety glasses.
Do not breathe vapour/spray.
PROTECTIVE MEASURES
Ensure good ventilation and avoid heat sources.
Adopt a high standard of personal hygiene. In case of skin contact, wash thoroughly with soap and wa­ter.
Use safety glasses, impervious gloves and lab coat. Avoid contamination inside the gloves. If overalls become contaminated, discontinue use and clean thoroughly.
No special respiratory precautions are necessary n normal use. Do no breathe vapour/spray when handling hot materials.
STORAGE/TRANSPORT
Store and transport only in correctly marked con­tainers. Keep containers tightly sealed when not in use. Keep in a cool, well ventilated area, out of sun­light and away from naked flames. Store well away from foodstuffs and drinking water.
Wear splash goggles, full suit, boots and gloves. Absorb leak/spill with an inert material and dispose of unwanted or absorbed substance through an au­thorised contractor to a licensed site. Finish clean­ing by spreading water on the contaminated sur­face and allow to evacuate through the sanitary system.
vii
Page 10
EMERGENCY ACTION
S Fire
Extinguishing media: Large fire Use water spray, fog or foam. Do not use water jet. Small fire Use dry chemical powder or CO Firefighters to use self contained breathing apparatus and full turnout gear. Keep fire ex-
2
posed containers cool.
S Ingestion
Do not induce vomiting, Obtain medical advice immediately.
S Inhalation (of vapour)
Remove from further exposure. Obtain medi­cal attention.
Generator Set Warning Labels
Warning signs are provided on the generator set at or near the point of risk. To avoid injury, always take the necessary precautions – as indicated on the sample signs shown below:
Caution / Warning. Indicates a risk of personal injury.
Caution / Warning of Temperature Hazard. Indicates a risk of personal injury from high temperature.
Caution / Warning of High Voltage Hazard. Indicates a risk of personal injury from electric shock/electrocution.
Caution / Warning. Indicates a risk of personal injury from equipment that may be subject to automatic starting or remote starting.
Caution / Warning. Indicates to read Operator manual for additional information.
Caution / Warning of Belt and Rotating Part Hazard. Indicates a risk of personal injury from entanglement in moving parts.
Caution / Warning of Pressure Hazard. Indicates a risk of personal injury from pressurized fluids.
viii
Page 11
1. Introduction
ABOUT THIS MANUAL
This is the Operator’s Manual for the generator sets (gensets) listed on the front cover. Read and care­fully observe all of the instructions and precautions in this manual. Keep this manual and the genset Installation Manual with the other vehicle manuals.
This is the Service Manual for the generator sets (gensets) listed on the front cover.
Operation, Periodic Maintenance and Trouble­shooting provide the instructions necessary for op-
erating the genset and maintaining top perfor­mance. The owner is responsible for performing maintenance in accordance with the PERIODIC MAINTENANCE SCHEDULE (p. 3-1).
WARNING
tem. It can stop without warning. Children, per­sons with physical or mental limitations, and pets could suffer personal injury or death. A per­sonal attendant, redundant power or alarm sys­tem must be used if genset operation is critical.
This genset is not a life support sys-
numbers is significant. The last character of the model number is the specification letter, which is im­portant for obtaining the right parts. Genuine Onan® replacement parts are recommended for best results. Refer to the genset Parts Catalog.
[The engine family designation, engine displacement, state­ment of compliance with applicable EPA and / or California emissions regulations appear in this block on the actual name­plate on the genset.]
WARNING
This generator set is not “ignition protected” and shall not be used in a flammable vapor environment.
WARNING
Improper service or replacement of parts can lead to severe personal injury or death and to damage to equipment and property. Ser­vice personnel must be qualified to perform electrical and mechanical service.
Unauthorized modifications or replacement of fuel, exhaust, air intake or speed control system components that affect engine emissions are prohibited by law in the State of California.
NAMEPLATE
Be ready to provide the genset model and serial numbers on the nameplate when contacting Onan for parts, service or information. Figure 1-1 illus­trates the nameplate and its location. The gray boxes illustrate where to look for the model and seri­al numbers.
FIGURE 1-1. TYPICAL NAMEPLATE
MODEL NUMBER: ___________________________
SERIAL NUMBER: ___________________________
Record these numbers in Figure 1-2 so that they are easy to find when needed. Each character in these
FIGURE 1-2. RECORD NUMBERS HERE
1-1
Page 12
HOW TO OBTAIN SERVICE
Information to Have Ready
When you call for service, parts, or product literature (such as the Service Manual or Parts Catalog) for your genset, contact the nearest authorized distrib­utor. Onan has factory-trained representatives to handle your requests for genset parts and service.
In North America
Call 1-800-888-ONAN to contact the nearest Cum­mins/Onan or Onan-only distributor in the United States or Canada. (This automated service utilizes touch-tone phones only). Select OPTION 1 (press 1) to be automatically connected to the dis­tributor nearest to you.
If you are unable to contact a distributor using the automated service, consult the Yellow Pages. Typi­cally, our distributors are listed under:
GENERATORS ELECTRIC, ENGINES GASOLINE OR DIESEL, or RECREATIONAL VEHICLES − EQUIPMENT, PARTS AND SERVICE.
If you have difficulty in arranging service or resolv­ing a problem, please contact the Service Manager at the nearest Cummins/Onan distributor for assis­tance.
Outside North America
If you are outside North America, call Onan Corpo­ration at 1−763−574−5000 from 7:30 AM to 4:00 PM, Central Standard Time, Monday through Friday, or fax 1−763−528−7229.
Before calling for service, have the following infor­mation available:
1. The complete genset model number and serial
number. See About This Manual (Page 1-1).
2. The date of purchase
3. The nature of the problem. See Section 4. Trou-
bleshooting.
NOISE
Generator sets emit noise. As noise level and time of exposure increase, risk of hearing damage in­creases. The Specifications page n the Operator manual states noise level for this generator set. Se­lect and use personal hearing protection appropri­ate for your exposure to generator set noise.
Note for use in countries where compliance to the EU Noise directive is required: This generator set has not been evaluated and is not marked for use in open air. Install the generator set in accordance with the Installation manual. Obey local noise restric­tions when you operate the generator set.
ELECTROMAGNETIC COMPATIBILITY
Generator sets emit and receive electromagnetic (radio frequency) energy. If the generator set af­fects operation of nearby devices, or nearby de­vices affect generator set operation, increase the distance between them.
This generator set has been evaluted for use in in­dustrial environments.
1-2
Page 13
EMISSIONS
genset is authorized, you should seek assistance from an approved Onan dealer.
You should carefully review Operator (Owner), Installation manuals and other information you re­ceive with your genset. If you are unsure that the installation, use, maintenance or service of your
TABLE 1-1. EMISSIONS CONTROL INFORMATION TABLE
The California emissions control warranty statement is located in
Emissions Warranty Information
Engine Valve Clearance (Lash) See Section 5. Specifications.
Engine Fuel Requirements
Engine Lubricating Oil Requirements See ENGINE OIL RECOMMENDATIONS (Page 2-1).
Engine Adjustments
Engine Emission Control System
the same packet of information as this manual when the genset is shipped from the factory.
The engine is certified to operate on diesel fuel. See FUEL REC­OMMENDATIONS (Page 2-1).
High Idle Speed. This is a service procedure requiring trained personnel and proper tools. See the Service Manual.
The engine emission control system consists of engine design and precision manufacture. (IFI)
California genset users may use Table 1-1 as an aid in locating information related to the California Air Resources Board requirements for emissions con­trol.
1-3
Page 14
TYPICAL GENSET
Figure 1-3 illustrates the fuel, battery, remote con­trol and AC output connection points, the flow of
cooling and ventilating air and the maintenance and service access panels of a typical genset. Not shown are the combustion air inlet and oil drain openings in the base.
AC OUTPUT AND REMOTE
CONTROL CONNECTIONS
COOLING & VENTILATING AIR IN HOT AIR OUT
MAINTENANCE
ACCESS
CONTROL
PANEL
BATTERY
CONNECTIONS
FUEL
CONNECTIONS
EXHAUST
CONNECTIONS
FIGURE 1-3. TYPICAL GENSET
1-4
Page 15
2. Operation
RECOMMENDED FUEL
WARNING
cause severe personal injury or death. Do not smoke near fuel tanks or fuel-burning equip­ment or in areas sharing ventilation with such equipment. Keep flames, sparks, pilot flames, electrical arcs and switches and all other sources of ignition well away. Keep a multi­class fire extinguisher handy.
Use clean, fresh No. 2 diesel fuel (ASTM 2-D) when the outdoor ambient temperature is above freezing, and No. 1 diesel fuel (ASTM 1-D) when below freez­ing. The fuel should have a Cetane number of at least 45 for reliable starting.
Diesel fuel is combustible and can
RECOMMENDED COOLANT
Use the best quality ethylene glycol antifreeze solu­tion available. It should be fully formulated with rust inhibitors and coolant stabilizers. Use fresh water that is low in minerals and corrosive chemicals. Dis­tilled water is best.
See Section 5. Specifications for coolant capacity.
RECOMMENDED ENGINE OIL
FIGURE 2-1. OIL VISCOSITY VS. TEMPERATURE
Use API (American Petroleum Institute) perfor­mance Class CH-4 engine oil or better. Also look for the SAE (Society of Automotive Engineers) viscos­ity grade. Referring to Figure 2-1, choose the vis­cosity grade appropriate for the ambient tempera­tures expected until the next scheduled oil change. Multi-grade oils such as SAE 15W-40 are recom­mended for year-round use.
See Section 5. Specifications for oil capacity.
STARTING BATTERIES
The genset requires a 12 volt battery to power its control and starting circuits. Reliable genset starting and starter service life depend upon adequate bat­tery system capacity and maintenance.
See MAINTAINING THE BATTERY AND BATTERY CONNECTIONS (p. 3-6) and Section 5. Specifi- cations for minimum required battery ratings.
2-1
Page 16
CONTROL PANEL
The control panel (Figure 2-2) has the following fea­tures:
(Rapid blinking before cranking starts indicates that the glow plugs are preheating the combustion chambers. The genset controller automatically var­ies the time based on engine temperature.)
Control Switch This switch is used to start and stop the genset, prime the engine fuel system and restore the fault code (blinking status light).
Status Lamp This is a lamp in the control switch that blinks rapidly during preheat and cranking. It stays on continuously while the genset is running. If the genset shuts down, it will blink a numerical code to indicate the nature of the fault shutdown (see Section 4. Troubleshooting).
LINE CIRCUIT
BREAKER(S)
Line Circuit Breaker(s) The line circuit breakers protect the AC power leads connected to the gen­set.
Coolant Recovery Tank Fill Cap − The recovery tank provides for coolant expansion. Replenish the normal loss of coolant by filling here.
Hour Meter The hour meter records the total run- ning time of the genset. It cannot be reset.
COOLANT RECOVERY
TANK FILL CAP
CONTROL SWITCH
&STATUS LAMP
COOLANT RECOVERY
TANK FLUID LEVEL
HOUR METER
FIGURE 2-2. CONTROL PANEL
2-2
Page 17
REMOTE CONTROL PANELS
There probably is a remote genset control panel in­side the vehicle. Onan offers three remote control kits as follows:
S Remote switch / status lamp (Figure 2-3).
S Remote switch / status lamp and hour meter
(Figure 2-4).
S Remote switch / status lamp and DC voltmeter
(Figure 2-5).
The DC voltmeter indicates whether voltage across the 12 VDC control system and battery is normal. If the indicator consistently stays above or below the normal zone, see MAINTAINING THE BATTERY AND BATTERY CONNECTIONS (p. 3-6).
FIGURE 2-3. REMOTE SWITCH
FIGURE 2-4. REMOTE SWITCH / HOUR METER
FIGURE 2-5. REMOTE SWITCH / DC VOLTMETER
2-3
Page 18
WARNING
EXHAUST GAS is deadly. All en­gine exhaust contains carbon monoxide; an odorless, colorless, poisonous gas that can cause unconsciousness and death. Symptoms of carbon monoxide poisoning include:
Dizziness Headache
Nausea Weakness and Sleepiness
Vomiting Inability to Think Coherently
4. Turn off air conditioners and other large ap­pliances.
PRIMING THE FUEL SYSTEM
The fuel system should be primed after replacing the fuel filter or running the genset out of fuel. To prime the fuel system, hold the control switch down in its Stop position for half a minute.
WARNING
IF YOU EXPERIENCE ANY OF THESE SYMPTOMS, GET INTO FRESH AIR IM­MEDIATELY. If symptoms persist, seek medical attention. Shut down the genset and do not op­erate it until it has been inspected and repaired.
WARNING
Never sleep in the vehicle while the genset is running unless the vehicle has a work­ing carbon monoxide detector. The exhaust system must be installed in accordance with the genset Installation Manual. Make sure there is ample fresh air when operating the genset in a confined area.
PRE-START CHECKS
Before the first start of the day and after every eight hours of operation, inspect the genset as instructed under GENERAL INSPECTION (p. 3-2). Keep a log of maintenance and the hours run and perform any maintenance that may be due. See Returning the Genset to Service (p. 2-7) if the vehicle has been in storage.
Before each start:
1. Make sure all vehicle carbon monoxide (CO) detectors are working.
2. Check for signs of fuel and exhaust leaks and damage to the exhaust system.
3. To prevent overheating and to reduce fouling with dust and debris, make sure the genset’s normal ground clearance is not being reduced by sloping ground, curbs, logs or other objects. Repark the vehicle if necessary and/or remove any objects blocking the air inlet or air outlet.
MANUAL STARTING
The genset can be started and stopped from the genset control panel or from a remote panel.
1. Perform the PRE-START CHECKS, prime the fuel system if necessary, and turn off the air conditioners and other large electrical loads.
2. Visually inspect for fuel, exhaust and coolant leaks. Do not start the genset if there is a fuel, exhaust or coolant leak and have it repaired.
3. Push and hold Start until the genset starts. The status lamp will come on when the genset starts and will stay on while it runs. While starting it will blink rapidly indicating preheating and crank­ing. (Depending on how cold it is, preheating can take up to 15 seconds, extending the time that the lamp blinks.)
CAUTION
Excessive cranking can over­heat and damage the starter motor. Do not crank for more than 30 seconds at a time. Wait at least 2 minutes before trying again.
4. See Section 4. Troubleshooting if the genset does not start after several tries.
5. Let the genset warm up a few minutes until it is running smoothly before connecting the ve­hicle electrical loads (appliances).
MANUAL STOPPING
Run the genset under no load for a few minutes to allow the engine to cool down and then push and re­lease Stop.
2-4
Page 19
AUTOMATIC STARTING AND STOPPING
The vehicle may be equipped with an inverter-char­ger or other automatic genset starting device. Al­ways follow the instructions and safety precautions provided by the manufacturer of the automatic start­ing device when enabling automatic genset starting.
WARNING
EXHAUST GAS is deadly. MOV-
ING PARTS and ELECTRICITY can cause severe personal injury or death. To reduce exposure to these hazards, always disable automatic genset starting before:
S Sleeping in vehicle, unless vehicle has a
working CARBON MONOXIDE detector
S Parking vehicle in garage or confined space
S Parking vehicle for storage
S Servicing genset
S Servicing batteries
S Servicing electrical appliances
S Fueling vehicle
LOADING THE GENSET
The genset can power AC motors, air conditioners, AC/DC converters, battery chargers and other ap­pliances. How much appliance load* can be pow­ered depends upon the genset power rating. The genset will shut down or its circuit breakers will trip if the sum of the loads exceeds genset power. See Section 4. Troubleshooting.
To avoid overloading the genset and causing shut­downs, compare the sum of the loads of the ap­pliances that are likely to be used at the same time to the power rating of the genset. Use Table 2-1 or the ratings on the appliances themselves (if so marked) to obtain the individual appliance loads. It may be
necessary to run fewer appliances at the same time—the sum of the loads must not be greater than genset rating.
The genset may shut down due to overload when a large motor or air conditioner is started or cycles off
and then on again, even though the sum of the loads is less than genset rating. The reason for this is that a motor’s startup load is much larger than its running load. It may be necessary to run fewer ap-
pliances when large motors and air condition­ers are cycling on and off.
Maximum power decreases as altitude increases because air density decreases. For every 1000-foot (305 m) increase in elevation you can expect power to decrease approximately 3.5 percent. Table 2-2 shows the results of typical calculations. It may be
necessary to run fewer appliances at higher alti­tudes.
TABLE 2-1. TYPICAL APPLIANCE LOADS
Appliance Air Conditioner 1400-2000 Battery Charger Up to 3600 DC Converter 300-900 Refrigerator 600-1000 Microwave Oven 1000-1500 Electric Frying Pan or Wok 1000-1500 Electric Stove Element 350-1000 Electric Water Heater 1000-1500 Electric Iron 500-1200 Electric Hair Dryer 800-1500 Coffee Percolator 550-750 Television 200-600 Radio 50-200 Electric Drill 250-750 Electric Broom 200-500 Electric Blanket 50-200
TABLE 2-2. POWER VS. ALTITUDE
Elevation above Sea
Level
at/below 500 ft (152 m) 12,000 W (rated)
at 2500 ft (762 m) 11,280 W
at 5500 ft (1676 m) 10,200 W
above 5500 ft (1676 m)
10,200 W minus 360 W
Load (watts)
Maximum Power
every 1000 ft (305 m)
* Appliance load and genset power are measured in terms of watts (W) or kilowatts (kW), where 1 kilowatt (kW) = 1000 watts (W).
2-5
Page 20
RESETTING CIRCUIT BREAKERS
OPERATING IN COLD WEATHER
If a circuit breaker in the main power distribution panel of the vehicle or on the genset (Figure 2-2) trips, either a circuit shorted or too many appliances were running. Note that the genset will continue to run after a circuit breaker trips.
If a circuit breaker trips, disconnect or turn off as many loads as possible and reset the circuit break­er. (Push the circuit breaker to OFF to reset it and then to ON to reconnect the circuit.) If the circuit breaker trips right away, either the electrical dis­tribution system has a short or the circuit breaker is faulty. Call a qualified electrician.
If the circuit breaker does not trip, reconnect the ap­pliances, one by one, up to a total load that does not overload the genset or cause the circuit breaker to trip. If a circuit breaker trips right away when an ap­pliance is connected, the appliance probably has a short.
Electrical appliances and tools must be used and maintained properly and be properly grounded to cause the line circuit breakers to trip when short cir­cuits occur.
Make sure the engine oil viscosity is appropriate for the cold weather temperatures. See ENGINE OIL RECOMMENDATIONS (Page 2-1). Be sure to change the oil if a sudden drop in temperature oc­curs.
OPERATING IN HOT WEATHER
Pay particular attention to the following items when operating the genset in hot weather:
1. Make sure nothing blocks airflow to and from the genset.
2. Make sure engine oil viscosity is appropriate for the ambient temperatures. See ENGINE OIL RECOMMENDATIONS (Page 2-1).
3. Keep the genset clean.
4. Perform maintenance due. See PERIODIC MAINTENANCE SCHEDULE (Page 3-1).
OPERATING AT HIGH ALTITUDE
WARNING
pliances and tools can cause fire and electrical shock leading to severe personal injury or death. Read and follow the equipment and tool manufacturer’s instructions and warnings re­garding use, maintenance and proper ground­ing.
Short circuits in electrical ap-
CONNECTING TO UTILITY POWER
A vehicle with provisions for connecting utility power must have an approved device to keep the genset and utility from being interconnected. See the gen­set Installation Manual for more information.
WARNING
public utility (or any other power source) can lead to electrocution of utility line workers, equipment damage and fire. Use an approved switching device to prevent interconnections.
Interconnecting the genset and the
For the effect of altitude on maximum power, see LOADING THE GENSET (Page 2-5).
OPERATING IN DUSTY ENVIRONMENTS
Pay particular attention to the following items when operating the genset in dusty environments:
1. Do not let dirt and debris accumulate inside the genset compartment. Keep the genset clean.
2. Perform air cleaner maintenance more often. See PERIODIC MAINTENANCE SCHEDULE (Page 3-1).
3. Change engine oil more often. See PERIODIC MAINTENANCE SCHEDULE (Page 3-1).
4. Keep containers of engine oil that have been opened tightly closed to keep out dust.
2-6
Page 21
BREAKING IN A NEW ENGINE
Proper engine break-in on a new genset or on one with a rebuilt engine is essential for top engine per­formance and acceptable oil consumption. Run the genset at approximately 1/2 rated power for the first 2 hours and then at 3/4 rated power for 2 more hours. See LOADING THE GENSET (Page 2-5).
WARNING
and can accumulate to dangerous levels in garages and other confined spaces. Dis­able the automatic genset starting feature of an inverter-charger or other automatic starting device before storing the vehicle.
2. Push the genset line circuit breaker OFF (Page 2-6).
CARBON MONOXIDE is deadly
Proper engine oil and oil level are especially critical during break-in because of the higher engine tem­peratures that can be expected. Change the oil if not appropriate for the ambient temperatures during break-in. See ENGINE OIL RECOMMENDATIONS (Page 2-1). Check oil level twice a day or every 4 hours during the first 24 hours of operation and change the oil and oil filter after the first 50 hours of operation.
EXERCISING THE GENSET
Exercise the genset at least 2 hours each month if use is infrequent. Run the genset at approximately 1/2 rated power. See LOADING THE GENSET (Page 2-5). A single two hour exercise period is better than several shorter periods.
Exercising a genset drives off moisture, re-lubri­cates the engine, replaces stale fuel and removes oxides from electrical contacts. The result is better starting, more reliable operation and longer engine life.
STORING THE GENSET
Proper storage is essential for preserving top gen­set performance and reliability when the genset cannot be exercised regularly and will be idle for more than 120 days.
Storing the Genset
1. Disable the automatic genset starting feature of an inverter-charger or other automatic starting device.
3. Change the engine oil and attach a tag indicat­ing oil viscosity. See ENGINE OIL REC­OMMENDATIONS (Page 2-1).
4. Disconnect the battery cables (negative [−] cable first) from the starting battery and store the battery according to the battery manufac­turer’s recommendations. See MAINTAINING THE BATTERY AND BATTERY CONNEC­TIONS (Page 3-6).
5. Plug the exhaust tail pipe to keep out dirt, mois­ture, bugs, etc.
6. Close the fuel supply valve (if so equipped).
Returning the Genset to Service
1. Check the oil tag on the genset and change the oil if the viscosity indicated is not appropriate for the temperatures expected. See ENGINE OIL RECOMMENDATIONS (Page 2-1).
2. Reconnect the starting battery (negative [−] cable last). See MAINTAINING THE BATTERY AND BATTERY CONNECTIONS (Page 3-6).
3. Remove the plug from the exhaust tailpipe.
4. Change the air filter element if it is dirty (Page 3-6).
5. Open the fuel supply valve (if so equipped).
6. Inspect the genset. See GENERAL INSPEC­TION (Page 3-2).
7. Push the genset line circuit breaker ON (Page 2-6) when the genset is ready to power appliances.
8. Enable the automatic genset starting feature of an inverter-charger or other automatic starting device following the device manufacturer’s in­structions and safety precautions.
2-7
Page 22
2-8
Page 23
3. Periodic Maintenance
Periodic maintenance is essential for top perfor­mance and long genset life. Use Table 3-1 as a guide for normal periodic maintenance. In hot and
any engine repair establishment or individual. How­ever, warranty work must be completed by an au-
thorized Onan dealer. dusty environments some maintenance procedures should be performed more frequently, as indicated by the footnotes in the table.
WARNING
Accidental or remote starting can
cause severe personal injury or death. Discon-
Maintenance, replacement or repair of emission control devices and systems may be performed by
TABLE 3-1. PERIODIC MAINTENANCE SCHEDULE
1
After
First 50
Hrs
3-4
Every
MAINTENANCE TASK
General Inspection 3-2
Check Engine Oil Level 3-2
Check Engine Coolant Level 3-10
Check Battery & Battery Connections
Change Engine Oil & Oil Filter
Clean Spark Arrestor
Replace Engine Air Filter
Replace Fuel Filter
Flush Coolant System
Replace Coolant Pressure Cap
3,7
3
5
1, 2, 3
2, 3
5
nect the negative (−) cable at the battery to pre-
vent starting while working on the genset.
FREQUENCY
Day
Every
Month
3-6
Every
250 Hrs
Every
500 Hrs
3-7
3-9
Every
800 Hrs
Every
1500
Hrs
3-10
3-10
Page
Check Generator Slip Rings/ Brushes
Replace Generator Bearing
2,7
7
1. Perform more often when operating in hot weather.
2. Perform more often when operating in dusty conditions.
3. Perform at least once a year.
4. Tighten or replace the belt (the one closest of the two to the engine) in accordance with the Service Manual if it can be deflected more than 1/2 in (12 mm) by thumb. (The tension on the front belt is automatically adjusted.)
5. Perform at least once every two years.
6. Perform at least once every five years.
7. Must be performed by trained and experienced personnel (authorized Onan service representatives).
8. EPA requirement.
3-1
Page 24
GENERAL INSPECTION
Inspect the genset before the first start of the day and after every eight hours of operation.
Do not operate power ventilators or exhaust fans while the vehicle is standing with the genset run­ning. The ventilator or fan can draw exhaust gases into the vehicle.
Oil Level
Check engine oil level (Figure 3-1).
Engine Coolant System
CAUTION
level is low can cause serious engine damage.
Check the engine coolant level and look for coolant leaks around the bottom of the genset and on the ground below. Minor leaks that can be replenished by daily additions of coolant to the recovery tank should be repaired by a qualified service technician as soon as possible. Larger leaks are cause for shutting down the genset until it can be repaired.
Operating the genset when coolant
Exhaust System
WARNING
operate the genset if there is an exhaust leak or any danger of exhaust gases entering or being drawn into the vehicle.
Look and listen for exhaust system leaks while the genset is running. Shut down the genset if a leak is found and have it repaired before operating the gen­set again.
Look for openings or holes between the genset compartment and vehicle cab or living space if the genset engine sounds louder than usual. Have all such openings or holes closed off or sealed to pre­vent exhaust gases from entering the vehicle.
Replace dented, bent or severely rusted sections of the tailpipe and make sure the tailpipe extends at least 1 inch (25.4 mm) beyond the perimeter of the vehicle.
WARNING
or brush. Contact with the exhaust system can cause a fire.
Park the vehicle so that the genset exhaust gases can disperse away from the vehicle. Barriers such as walls, snow banks, high grass and brush and oth­er vehicles can cause exhaust gases to accumulate in and around the vehicle.
EXHAUST GAS IS DEADLY! Do not
Do not park the vehicle in high grass
Fuel System
Check for leaks at hose, tube and pipe fittings in the fuel supply system while the genset is running and while it is stopped. Check flexible fuel hose sections for cuts, cracks, and abrasions. Make sure the fuel line is not rubbing against other parts. Replace worn or damaged fuel line parts before leaks occur.
WARNING
Diesel fuel leaks can lead to fire. Do not operate the genset if operation causes fuel to leak.
Prime the fuel system if the genset ran out of fuel.
Battery Connections
Check the battery terminals for clean, tight connec­tions. Loose or corroded connections have high electrical resistance which makes starting harder. See MAINTAINING THE BATTERY AND BATTERY CONNECTIONS (p. 3-6).
Mechanical
Visually inspect genset for mechanical damage, For generator sets with a sound shield, install service doors before running the generator set to listen for unusual noises. Check the genset mounting bolts. Check to see that the generator set air inlet and out­let openings are not clogged with debris or blocked. Keep the generator set compartment clean.
To prevent overheating and to reduce fouling with dust and debris, make sure the genset’s normal ground clearance is not being reduced by sloping ground, curbs, logs or other objects. Repark the ve­hicle if necessary and/or remove any objects block­ing the air inlet or air outlet.
CHECKING ENGINE OIL LEVEL
WARNING
termined that contact with used engine oil can cause cancer or reproductive toxicity. Avoid skin contact and breathing of vapors. Use rub­ber gloves and wash exposed skin.
WARNING
hoses, etc) will be hot and can cause severe burns. The use of protective gloves is recom­mended.
State and federal agencies have de-
Engine components (drains, filters,
3-2
Page 25
WARNING
Accidental or remote starting can cause severe personal injury or death. Discon­nect the negative (−) cable at the battery to pre- vent starting while working on the genset.
WARNING
Do not run the genset with the main­tenance access covers off. Contace with haz­ardous moving parts and hot exhaust manifolds can cause severe personal injury.
1. Park the vehicle on level ground, shut down the genset and remove the front access door.
2. Pull out the oil dip stick, wipe it clean, reinsert it and pull it out again to check the oil level (Fig­ure 3-1).
3-3
Page 26
3. Add or drain oil as necessary. See REC­OMMENDED ENGINE OIL (p. 2-1). Keep the oil level between the FULL and ADD marks.
CAUTION
Too much oil can cause high oil consumption. Too little oil can cause severe engine damage. Keep the oil level between the FULL and ADD marks.
WARNING
Do not run the genset with the main­tenance access covers off. Contace with haz­ardous moving parts and hot exhaust manifolds can cause severe personal injury.
Refer to Table 3-1 for scheduled engine oil change. Change oil more often in hot and dusty environ­ments.
4. Reinsert the dipstick and secure the oil fill cap and front access door.
CHANGING ENGINE OIL AND OIL FILTER
WARNING
termined that contact with used engine oil can cause cancer or reproductive toxicity. Avoid skin contact and breathing of vapors. Use rub­ber gloves and wash exposed skin.
WARNING
hoses, etc) will be hot and can cause severe burns. The use of protective gloves is recom­mended.
WARNING
cause severe personal injury or death. Discon­nect the negative (−) cable at the battery to pre- vent starting while working on the genset.
State and federal agencies have de-
Engine components (drains, filters,
Accidental or remote starting can
1. Place a pan under the oil drain plug (Fig­ure 3-1), run the genset until warm and shut it off.
2. Remove the front access door and the oil fill cap, unscrew the oil drain plug and drain all the oil from the engine. Reinstall the oil drain plug securely.
3. Spin off the oil filter canister and clean the filter mounting surface on the engine block. Remove the old gasket if it remains.
4. Make sure the gasket is in place on the new fil­ter and apply a thin film of clean oil to the gas­ket. Spin the new filter on until the gasket just touches the block. Turn it an additional 1/2 to 3/4 turn. Do not overtighten.
5. Refill with 5.9 quarts (5.6 liters) of oil, check oil level (Figure 3-1) and secure the front access door.
6. Dispose of the used oil and oil filter according to local environmental regulations.
3-4
Page 27
FILL CAP
FILTER
DIP STICK
DRAIN PLUG
(22 MM HEX HEAD)
FIGURE 3-1. ENGINE OIL MAINTENANCE
3-5
Page 28
MAINTAINING THE BATTERY AND
BATTERY CONNECTIONS
WARNING
light switches or other equipment, and flames or sparks, can ignite battery gas causing severe personal injury—Ventilate battery area before working on or near battery—Wear safety glasses—Do not smoke—Switch work light ON or OFF away from battery—Stop genset and dis­connect charger before disconnecting battery cables—Disconnect negative () cable first and reconnect last.
Refer to Table 3-1 for scheduled battery mainte­nance, and follow the battery manufacturer’s in­structions. Have the battery charging system ser­viced if DC system voltage is consistently low or high. Always:
1. Keep the battery case and terminals clean and dry and the terminals tight.
2. Remove battery cables with a battery terminal puller.
3. Make sure which terminal is positive (+) and which is negative () before making battery connections, always removing the negative (−) cable first and reconnecting it last to reduce arcing.
Arcing at battery terminals or in
REPLACING THE AIR FILTER ELEMENT
WARNING
hoses, etc) will be hot and can cause severe burns. The use of protective gloves is recom­mended.
WARNING
tenance access covers off. Contact with hazar­douse moving parts and hot exhaust manifolds can cause severe personal injury.
WARNING
cause severe personal injury or death. Discon­nect the negative (−) cable at the battery to pre- vent starting while working on the genset.
Refer to Table 3-1 for scheduled air filter replace­ment. Replace it more often in dusty environments.
The air filter is accessible through the front access door (Figure 3-2). Loosen the three screws that se­cure the coolant recovery tank to the housing top panel and move it out of the way. Loosen the two screws that secure the air filter housing to the hous­ing top panel so that the spring clips that secure the filter housing end cap can be unlatched. Remove the end cap and replace the filter element. Secure the filter housing, coolant tank and access door.
Engine components (drains, filters,
Do not run the genset with the main-
Accidental or remote starting can
3-6
Page 29
COOLANT
RECOVERY TANK
(SHOWN CUT AWAY)
AIR FILTER HOUSING
END CAP
FIGURE 3-2. REPLACING THE AIR FILTER ELEMENT
3-7
Page 30
REPLACING THE FUEL FILTER
Removing the Fuel Filter
See Table 3-1 for scheduled fuel filter replacement. A dirty fuel filter may be the cause of a failure to start. The fuel filter is accessible through the front access door (Figure 3-3).
WARNING
Diesel fuel is combustible and can cause severe personal injury or death. Do not smoke near diesel fuel tanks or equipment. Keep flames, sparks, pilot lights, electrical switches, arc-producing equipment and all oth­er sources of ignition well away. Keep a type ABC fire extinguisher in the vehicle.
WARNING
Close any fuel line shutoff valve be­fore disconnecting the fuel line from the filter.
WARNING
Accidental or remote starting can cause severe personal injury or death. Discon­nect the negative (−) cable at the battery to pre- vent starting while working on the genset.
WARNING
Engine components (drains, filters, hoses, etc) will be hot and can cause severe burns. The use of protective gloves is recom­mended.
Disconnect the two fittings at the filter and remove the mounting nut. Apply a wrench on the filter fitting as well as on the flare nut so as not to stress the fit­ting. Flare nut wrenches should be used on the flare nuts so as not to round the corners on the nuts. Dis­pose of the fuel filter according to local regulations. (Note: Filter removal will be easier if the filter mount­ing bracket screws are removed.)
CAUTION
Wipe dirt off the fuel hose fittings at the fuel filter before disconnecting the hoses so as to keep dirt out of the fuel system.
Installing the Fuel Filter
Rotate the filter half a turn around its mounting stud if the fittings interfere with the bracket. It only fits one way.
Connect the fuel fittings before tightening the filter mounting nut. Take care not to crossthread the fuel fittings. Thread them in by hand and tighten one flat
past seating with two wrenches.
WARNING
Accidental or remote starting can cause severe personal injury or death. Discon­nect the negative (−) cable at the battery to pre- vent starting while working on the genset.
Prime the fuel system for half a minute to fill the new filter with fuel.
Secure the access door.
3-8
Page 31
FILTER
MOUNTING NUT
HOSE TO
ENGINE
FUEL
FILTER
HOSE FROM
FUEL PUMP
FIGURE 3-3. FUEL FILTER
BRACKET
MOUNTING
SCREWS
3-9
Page 32
MAINTAINING THE COOLANT SYSTEM
Refer to Table 3-1 for scheduled maintenance. The engine cooling system is filled with a 50/50 mixture of ethylene glycol anti-freeze and water when the genset leaves the factory, which is suitable for tem­peratures down to -34
° F (-37° C).
Recommended Coolant
See RECOMMENDED COOLANT (p. 2-1).
remove the coolant drain plug (Figure 3-4) and drain the coolant into a suitable container.
WARNING
Ethylene glycol antifreeze is con­sidered toxic. Dispose of it according to local regulations for hazardous substances.
Flush and clean the cooling system before refilling. Radiator cleaning chemicals are available at local auto parts stores. Follow the instructions for clean­ing and flushing that come with the cleaning solu­tion.
Pressure Cap
Replace the pressure cap (Figure 3-4) every two years (seals deteriorate and leak). Proper cooling system pressure (14 psi) is essential for optimal en­gine cooling and minimal coolant loss.
Draining and Cleaning Cooling System
WARNING
burns. Let the engine cool before releasing the pressure cap or removing the drain cap.
WARNING
hoses, etc) will be hot and can cause severe burns. The use of protective gloves is recom­mended.
WARNING
cause severe personal injury or death. Discon­nect the negative (−) cable at the battery to pre- vent starting while working on the genset.
Hot coolant spray can cause severe
Engine components (drains, filters,
Accidental or remote starting can
Refilling Cooling System
Install the coolant drain plug using pipe thread seal­ant. Tighten it just enough so that it does not leak
when the genset is running and has warmed up. Pull the hose connected to the pressure cap assembly out as far and as high as it will go and fill the system with coolant. When the coolant level reaches the fill opening, start and operate the genset for a few min­utes and shut it down. Add more coolant if neces­sary and secure the pressure cap.
Fill the recovery tank with coolant mixture to the COLD mark.
WARNING
cause severe personal injury or death. Discon­nect the negative (−) cable at the battery to pre- vent starting while working on the genset.
WARNING
will prevent the system from filling to its capac­ity, which can lead to serious engine damage.
Accidental or remote starting can
Coolant trapped in the vent hose
Let the engine cool before removing the pressure cap. Relieve any remaining pressure by turning the pressure cap slowly, without pushing down. When the pressure has been relieved, push down on the cap, turn it the rest of the way and withdraw it. Then
Coolant Level Check
Check coolant level in the recovery tank (Fig­ure 3-4) before the first startup of each day and fill to the COLD mark if necessary.
3-10
Page 33
RECOVERY TANK
FILL CAP (BLUE)
COOLANT
LEVEL
COOLANT RECOVERY
TANK
PRESSURE CAP
AND SYSTEM
FILL OPENING
COOLANT DRAIN PLUG
(1/4 INCH HEX SOCKET)
FIGURE 3-4. ENGINE COOLING SYSTEM
3-11
Page 34
3-12
Page 35
4. Troubleshooting
TROUBLESHOOTING WITH TABLE 4-1
To aid troubleshooting the genset controller causes the status indicator light to blink the numeric code assigned to the fault that caused shutdown. For a brief description of the fault and step-by-step cor­rective action, refer to TABLE 4-1. TROUBLE­SHOOTING, which lists the fault codes in numerical order.
If you are unable to resolve the problem after taking the corrective actions suggested, contact an autho­rized Onan dealer. See HOW TO OBTAIN SER­VICE (p. ).
Many genset shutdowns can be avoided by perform­ing periodic maintenance on schedule (TABLE 3-1. PERIODIC MAINTENANCE SCHEDULE) and by not running the genset out of fuel. Note that when the genset and propulsion engine draw from the same fuel tank, the fuel dip tubes are usually arranged so that the genset will run out of fuel first. By marking the genset empty point on the fuel gauge, it will be easier to tell when the genset may run out of fuel.
S Two blinks indicate shutdown due to a loss of
engine oil pressure.
S Three blinks indicate a service fault. Press
Stop once to cause the two-digit, second-level
shutdown code to blink. (Pressing Stop again will stop the blinking.) The two-digit code con­sists of 1, 2, 3, 4 or 5 blinks, a brief pause, and then 1 to 9 blinks. The first set of blinks repre­sents the tens digit and the second set of blinks the units digit of the shutdown code number. For example, shutdown code No. 36 appears as:
blink-blink-blink—pause—blink-blink-blink-blink-blink-blink—
long pause—repeat
S Four blinks indicate that cranking time ex-
ceeded 35 seconds.
To avoid the possibility of anyone misinterpreting Code Nos. 3 and 4 as Code Nos. 33 and 44, the lat­ter have not been assigned faults.
RESTORING FAULT CODE BLINKING
FAULT CODE BLINKING
At fault shutdown, the status indicator light will re­peatedly blink sets of 1, 2, 3 or 4 blinks.
S One blink indicates shutdown due to high en-
gine coolant temperature.
The fault code stops blinking after five minutes. Press Stop three times within three seconds to re­store fault code blinking.
Note: The last fault logged will blink even though the condition that caused the shutdown may have been corrected.
4-1
Page 36
TABLE 4-1. TROUBLESHOOTING
WARNING
Some genset service procedures present hazards that can result in severe per­sonal injury or death. Only trained and experienced service personnel with knowledge of fuels, electricity, and machinery hazards should perform genset service. See Safety Precautions.
NO RESPONSE AT CONTROL SWITCH
(Faulty switch, poor or missing connections, dead battery)
Corrective Action:
1. Try the genset (local) control switch if there is no response at the remote control switch, and vice versa.
If there is no response at either remote or local switch, go to Step 3.
If there is no response at the remote switch but at the local, go to Step 4.
If there is no response at the local switch but at the remote, go to Step 7.
2. Check for 12 VDC across genset battery cable terminal block. Service as necessary by cleaning and tightening battery cable connections, recharging or replacing the battery or replacing damaged or missing battery cables.
3. Check for 12 VDC across genset battery cable terminal block TB1. If there is no voltage, service as necessary by cleaning and tightening battery cable connections, recharging or replacing the bat­tery or replacing damaged or missing battery cables. If there is voltage across TB1, but no response at either remote or local switch, go first to Step 4, and then, if necessary, also to Step 7.
4. Disconnect harness connector P8 from the remote circuits. Check for B+ (12 VDC) at P8-C (Start) and at P8-E (Stop) and for ground continuity at P8-A (Ground). If there is B+ and ground continuity, service the remote switch and harness. If not, go to Step 5.
5. Disconnect harness connector P1 from the control board and check for B+ at P1-10 and for ground continuity at P1-27. If there is B+ and ground continuity, go to Step 6. If not, go to Step 10.
6. Check for wiring continuity in the harness between connectors P8-C and P1-9 (Start), P8-E and P1-32 (Stop), P8-B and P1-7 (Status), P8-F and P1-8 (Run) and P8-A and P1-27 (Ground). Repair as necessary. Make sure connector pin sockets are not damaged or corroded and that they are fully seated and can’t be pulled out. Replace the control board if the genset still does not start.
7. Disconnect harness connector P9 from control switch S1. Check for B+ (12 VDC) at P9-3 (Start) and at P9-1 (Stop) and for ground continuity at P9-2 (Ground). If there is B+ and ground continuity, test control switch S1 and replace if necessary. If not, go to Step 8.
8. Disconnect harness connector continuity at P1-27. If there is B+ and ground continuity, go to Step 9. If not, go to Step 10.
9. Check for wiring continuity in the harness between connectors P9-3 and P1-9 (Start), P9-1 and P1-32 (Stop), P9-8 and P1-7 (Status), P9-7 and P1-27 (Status Ground) and P9-2 and P1-27 ( Start/ Stop Ground). Repair as necessary. Make sure connector pin sockets are not damaged or corroded and that they are fully seated and can’t be pulled out. Replace the control board if the genset still does not start.
10. Remove the top housing panel and check that both harness connectors labeled B1BAT are secure on the starter solenoid terminal, that GND is secure on the chassis ground and that there is wiring continuity in the harness between connectors P1-10 and B1BAT and between connectors P1-27 and GND. Repair as necessary. Make sure connector pin sockets are not damaged or corroded and that they are fully seated and can’t be pulled out. Replace the control board if the genset still does not start.
11. Remove the top housing panel and replace broken or missing cables between TB1 and the engine. Tighten loose connections.
P1 from the control board and check for B+ at P1-10 and for ground
4-2
Page 37
TABLE 4-1. TROUBLESHOOTING
WARNING
sonal injury or death. Only trained and experienced service personnel with knowledge of fuels, electricity, and machinery hazards should perform genset service. See Safety Precautions.
Some genset service procedures present hazards that can result in severe per-
THE STARTER ENGAGES AND DISENGAGES
(Low cranking voltage)
Corrective Action:
1. Have the vehicle propulsion engine running while trying to start the genset. Its charging alternator may be able to maintain a high enough battery terminal voltage to start the genset.
2. Service the battery as necessary by cleaning and tightening connections, recharging or replacing the battery or replacing damaged battery cables.
THE STARTING BATTERIES DO NOT MAINTAIN A CHARGE
(Marginal battery, battery connections or charging system)
Corrective Action: .
1. Service the battery as necessary by cleaning and tightening connections, recharging or replacing the battery or replacing damaged battery cables.
2. Have the battery recharging system serviced.
3. Models HDKCA and HDKCB The genset starting battery is recharged by the vehicle engine or separate battery charger. Service as required.
4. Models HDKCC and HDKCD These models have a feature whereby genset battery charging al­ternator G1 can be disabled, via relay K1, by connecting B+ to remote connector pin P8-D. Service the vehicle engine or separate battery charger if depended upon for recharging the genset starting battery. If genset battery charging alternator G1 is not disabled, continue with Step 5.
5. Remove the top housing panel and check for wiring continuity in the harness between charging alter­nator G1 and starter solenoid terminal B+ (BAT). Repair as necessary.
6. Check for proper operation of relay K1 and replace if necessary.
7. Check for wiring continuity in the harness between connectors G1-VR and K1-87a. Repair as neces- sary.
8. Disconnect harness connector P1 from the control board. Check for wiring continuity in the harness between connectors P1-24 and K1-30. Repair as necessary. Make sure connector pin sockets are not damaged or corroded and that they are fully seated and can’t be pulled out.
9. Replace battery charging alternator G1.
NO AC POWER WHEN GENSET IS RUNNING
(A Circuit Breaker is OFF, tripped or malfunctioning or there are poor AC harness connections)
Corrective Action: .
1. Reset or turn ON genset circuit breaker CB1.
2. Reset or turn ON any other circuit breaker in the AC power supply system.
3. Check voltage at genset AC output terminal block TB2 when the genset is running. If there is approxi­mately 120 VAC across TB2-1 and TB2-3 and across TB2-2 and TB2-3, repair or reconnect the wir­ing between the genset and the main vehicle distribution panel. If there is no voltage, go to Step 4.
4. Check for proper AC harness connections and repair as necessary.
5. Test each circuit breaker and replace if necessary.
4-3
Page 38
TABLE 4-1. TROUBLESHOOTING
WARNING
sonal injury or death. Only trained and experienced service personnel with knowledge of fuels, electricity, and machinery hazards should perform genset service. See Safety Precautions.
Some genset service procedures present hazards that can result in severe per-
ENGINE OVER TEMPERATURE—CODE NO. 1
(During normal operation engine coolant temperature exceeded 239° F [115° C] for 10 seconds)
Corrective Action:
1. Check engine coolant level, add coolant as necessary and repair any leaks.
2. Check for and remove any objects blocking the air inlet or outlet openings in the bottom of the genset and clean out dirt fouling the radiator passages.
3. Run fewer appliances at the same time to keep down engine temperature. (Note that high altitude and high ambient temperature decrease engine cooling capacity.)
4. Look for loose or broken fan belts and have them serviced. readjust or replace as necessary.
5. Clean and flush the cooling system to remove coolant passage fouling (p. 3-10).
6. Check for air leaks in the housing as a result of missing or loose housing panels and access covers, including the access cover for the AC terminals.
7. If loose, reconnect wiring harness connector E3-1 to engine coolant temperature sender E3. (The Controller interprets a loose lead touching ground as high temperature.)
8. Replace the coolant thermostat, which might not be fully opening. See Engine Workshop Manual 981-0541.
9. Test temperature sender E3 and replace if necessary.
LOW OIL PRESSURE—CODE NO. 2
(During normal operation engine oil pressure dropped to less than 14 psi for 3 seconds—switch closed)
Corrective Action:
1. Check engine oil level, add oil as necessary and repair any leaks.
2. Drain the excess oil if the level is above Full on the dipstick. If the level is too high the crankshaft can whip the oil into foam, which the pump can’t pump.)
3. Test low oil pressure cutoff switch S2 and replace if necessary.
4. Service the engine. See Engine Workshop Manual 981-0541.
SERVICE CHECK—CODE NO. 3
(A second-level fault occurred)
Corrective Action: Check the second-level fault code by momentarily pressing Stop. The second-lev­el fault will be one of the following in this table.
4-4
Page 39
TABLE 4-1. TROUBLESHOOTING
WARNING
sonal injury or death. Only trained and experienced service personnel with knowledge of fuels, electricity, and machinery hazards should perform genset service. See Safety Precautions.
Some genset service procedures present hazards that can result in severe per-
OVER CRANK—CODE NO. 4
(First-level fault code—Cranking time exceeded 35 seconds)
Corrective Action:
1. Check fuel level and refill as necessary. (Note: The genset fuel pickup is probably higher than the vehicle engine fuel pickup.)
2. Prime the engine fuel system for one minute (p. 2-4).If the fuel pump does not operate, check for loose wiring harness connectors E2-1 and E2-2 and reconnect them to the pump. If they were found connected, disconnect them and power the pump directly with a 12 volt battery. Replace the fuel pump if it does not operate. If the pump operates, disconnect P1 from the control board and check for wiring continuity in the harness between connectors P1-24 and E2-1 and for ground continuity at connector E2-2. Repair as necessary. Make sure connector pin sockets are not damaged or cor­roded and that they are fully seated and can’t be pulled out. Replace the control board if the fuel pump still does not operate.
3. Check the engine air filter and remove any blockage (p. 3-6).
4. Change the engine oil to oil of the proper viscosity for the ambient temperature. High oil viscosity can slow down cranking speed.
5. Check all fuel fittings for fuel and air leaks and tighten as necessary. Reprime.
6. Replace the fuel filter (p. 3-8).
7. Conduct a fuel flow test and service as necessary.
8. If loose, reconnect wiring harness connector HR-1 to the glow plug bus bar. If it was found connected, check for B+ on the glow plug bus bar while cranking. If there is B+, remove the glow plug bus bar and check for electrical continuity between each glow plug terminal and ground. Replace all three glow plugs if any glow plug is open. If there is no B+, check for proper operation of glow plug relay K3. If the relay functions properly, check for wiring continuity in the harness between connectors HR1 and K3-87 and for ground continuity at K3-86. If good, disconnect harness connector P1 from the control board and check for wiring continuity in the harness between connectors P1-23 and K3-85 and between P1-10 and K3-30. Repair as necessary. Make sure connector pin sockets are not dam­aged or corroded and that they are fully seated and can’t be pulled out. Replace the control board if there still is no B+ at the glow plug bus bar during cranking.
9. Remove the governor actuator, test it for proper operation and replace if necessary. (The engine can­not start if the actuator fails to pull in its spring-loaded plunger.)
10. Service the fuel injectors and injection pump.
11. Service the internal engine governor mechanism.
12. Service a worn engine.
OVER VOLTAGE—CODE NO. 12
(After voltage regulation was enabled Output Voltage jumped to more than 150 VAC
[125% of rated] for 75 milliseconds or to more than 138 VAC [115% of rated] for 3 seconds)
Corrective Action: See an authorized Onan dealer.
1. Push the line circuit breaker to OFF, start the genset and measure output voltage. If output voltage is normal, the problem is in the circuits external to the genset. If there is no voltage, test for and ser­vice a grounded or shorted main, field or quadrature windings or grounded or shorted voltage sense transformer.
2. Replace the control board.
4-5
Page 40
TABLE 4-1. TROUBLESHOOTING
WARNING
sonal injury or death. Only trained and experienced service personnel with knowledge of fuels, electricity, and machinery hazards should perform genset service. See Safety Precautions.
Some genset service procedures present hazards that can result in severe per-
UNDER VOLTAGE—CODE NO. 13
(After voltage regulation was enabled Output Voltage fell to less than 108 VAC
[90% of rated] for 5 seconds)
Corrective Action: Turn OFF the line circuit breaker on the operator’s console. If the genset now runs, run it with fewer connected loads.
1. Push the line circuit breaker to OFF, start the genset and measure output voltage. If output voltage is normal, the problem is in the circuits external to the genset. If there is no voltage, test for and ser­vice a grounded or shorted main, field or quadrature windings or grounded or shorted voltage sense transformer.
2. Replace the control board.
OVER FREQUENCY—CODE NO. 14
(After the starter was engaged Frequency jumped to more than 70 Hz
for 40 milliseconds or to more than 66 Hz for 6 seconds)
Corrective Action:
1. Check for a tripped genset circuit breaker, reset it if necessary, and run with fewer connected loads. (A breaker tripping under load can cause genset frequency to overshoot.)
2. Check all fuel fittings for fuel and air leaks and tighten as necessary. Reprime. (Air bubbles can disrupt frequency.)
3. Remove the governor actuator, test it for proper operation and replace if necessary.
4. Check high-idle speed and readjust if necessary.
5. Replace the control board.
6. Service the internal engine governor mechanism according to Engine Workshop Manual 981-0541.
UNDER FREQUENCY—CODE NO. 15
(During normal operation Frequency fell to less than 54 Hz for more than 8 seconds)
Corrective Action:
1. Push the line circuit breaker to OFF and restart the genset. If the genset now runs, run it with fewer connected loads, especially those with high motor starting loads such as air conditioners.
2. Check all fuel fittings for fuel and air leaks and tighten as necessary. Reprime. (Air bubbles can dis­rupt frequency.)
3. Replace the engine air filter and clean the spark-arrest muffler (p. 3-6).
4. Replace the fuel filter (p. 3-8).
5. Conduct a fuel flow test and service as necessary.
6. Remove the governor actuator, test it for proper operation and replace if necessary.
7. Check high-idle speed and readjust if necessary.
8. Replace the control board.
9. Service the fuel injectors and injection pump.
10. Check fuel injection timing.
11. Service the internal engine governor mechanism .
12. Service a worn engine.
4-6
Page 41
TABLE 4-1. TROUBLESHOOTING
WARNING
sonal injury or death. Only trained and experienced service personnel with knowledge of fuels, electricity, and machinery hazards should perform genset service. See Safety Precautions.
Some genset service procedures present hazards that can result in severe per-
ACTUATOR SHORTED OR OPEN—CODE NO. 19
(At startup the Controller sensed an open or shorted governor actuator/harness)
Corrective Action: See an authorized Onan dealer.
1. If loose, reconnect wiring harness connectors E1-1 and E1-2 to the governor actuator. If they were found connected, disconnect the wiring harness and measure electrical resistance across the actua­tor leads. Replace the actuator if resistance is not 2.8 to 2.9 ohms.
2. Disconnect harness connector P1 from the control board and check for wiring continuity in the har- ness between connectors P1-28 and E1-1 and for ground continuity at connector E1-2. Repair as necessary. Make sure connector pin sockets are not damaged or corroded and that they are fully seated and can’t be pulled out. Replace the control board if the fault still occurs.
ACTUATOR OVERLOAD—CODE NO. 22
(Due to connected overload or low engine performance, the Controller maintained the governor actuator
at full-duty cycle—maximum pulse-width-modulated square-wave signal [PWM]—for
60 consecutive seconds)
Corrective Action:
1. Reduce the number of appliances running at the same time, especially those with high motor starting loads such as air conditioners.
2. Check all fuel fittings for fuel and air leaks and tighten as necessary. Reprime.
3. Replace the engine air filter and clean the spark-arrest muffler (p. 3-6).
4. Replace the fuel filter (p. 3-8).
5. Conduct a fuel flow test and service as necessary.
6. Remove the governor actuator, test it for proper operation and replace if necessary.
7. Check high-idle speed and readjust if necessary.
8. Service the fuel injectors and injection pump.
9. Check fuel injection timing.
10. Service the internal engine governor mechanism.
11. Service a worn engine.
FAULTY ENGINE TEMPERATURE SENDER—CODE NO. 24
(After 10 minutes of normal operation the Controller checked for and sensed
an open temperature sender/harness)
Corrective Action: See an authorized Onan dealer.
1. If loose, reconnect wiring harness connector E3-1 to engine coolant temperature sender E3.
2. Test the temperature sender and replace if necessary.
3. Disconnect harness connector P1 from the control board and check for wiring continuity in the har- ness between connectors P1-21 and E3-1. Repair as necessary. Make sure connector pin sockets are not damaged or corroded and that they are fully seated and can’t be pulled out. Replace the con­trol board if the fault still occurs.
4-7
Page 42
TABLE 4-1. TROUBLESHOOTING
WARNING
sonal injury or death. Only trained and experienced service personnel with knowledge of fuels, electricity, and machinery hazards should perform genset service. See Safety Precautions.
Some genset service procedures present hazards that can result in severe per-
VAC SENSE LOST—CODE NO. 27
(The Controller lost VAC sensing during normal voltage regulation when the field was functioning nor-
mally and frequency was at least 40 Hz)
Corrective Action: See an authorized Onan dealer.
1. Disconnect harness connector P1 from the control board and check for electrical resistance between pins P1-33 and P1-34, which should be approximately 586 ohms (TX1 secondary winding. Go to Step 2 if the secondary circuit of voltage sense transformer TX1 is good. If not, disconnect the four harness leads from TX1 and test the transformer. Replace the transformer if either winding is faulty. If the transformer is good, check wiring continuity in harness leads P1-33—TX1-RED and P1-34—TX1-GRN. Repair or replace components as necessary. Make sure connector pin sockets are not damaged or corroded and that they are fully seated and can’t be pulled out.
2. Make sure the line circuit breaker (CB1/CB2) is OFF, disconnect the four harness leads from TX1 and test the transformer. Replace the transformer if either winding is faulty. If the transformer is good, check electrical resistance between harness leads TX1-S1 and TX1-S2, which should be approxi- mately twice the individual winding resistances in table (T1T2 + T3T4). If not, check wiring continu­ity in harness leads CB1-LINE—TX1-S1 and CB2-LINE—TX1-S2 and for proper connections of both sense leads and generator leads to the line terminals on CB1 and CB2. Repair, reconnect or replace components as necessary.
3. Replace the control board.
HIGH BATTERY VOLTAGE—CODE NO. 29
(During startup the Controller sensed that battery system voltage was greater than 19.2 volts for 5 milli-
seconds or greater than 19.2 volts for 1 second will running)
Corrective Action:
1. Check battery bank connections and reconnect if necessary so that the 12 volt batteries serving the genset are connected in parallel (12 volt) rather than in series (24 volt).
2. Select a lower battery booster charge rate.
4-8
Page 43
TABLE 4-1. TROUBLESHOOTING
WARNING
sonal injury or death. Only trained and experienced service personnel with knowledge of fuels, electricity, and machinery hazards should perform genset service. See Safety Precautions.
Some genset service procedures present hazards that can result in severe per-
STARTING FAULT—CODE NO. 32
(The Controller could not detect cranking speed [quadrature zero crossings] for 12 seconds)
Corrective Action:
1. Have the vehicle propulsion engine running while trying to start the genset. Its charging alternator may be able to maintain a high enough battery terminal voltage to start the genset.
2. Service the battery as necessary by cleaning and tightening connections, recharging or replacing the battery or replacing damaged battery cables.
3. Change the engine oil to oil of the proper viscosity for the ambient temperature. High oil viscosity can slow down cranking speed.
4. Remove the top housing panel and check for wiring continuity in the harness between connectors SW (starter solenoid) and K2-87 (starter pilot relay) and between K2-30 and B+ (BAT) (starter sole­noid). Repair as necessary.
5. Check for proper operation of starter pilot relay K2 and replace if necessary.
6. Disconnect harness connector P1 from the control board and check for wiring continuity in the har- ness between connectors J1-12 and K2-85 and for ground continuity at connector K2-86. Repair as necessary. Make sure connector pin sockets are not damaged or corroded and that they are fully seated and can’t be pulled out.
7. Service or replace the starter motor assembly.
8. Replace the control board.
EE CHECKSUM FAULT—CODE NO. 35
(During startup the genset Controller detected an EE memory error)
Corrective Action: See an authorized Onan dealer.
MECHANICAL FAULT—CODE NO. 36
(The Controller declared this fault because engine speed fell below 1000 RPM for 0.5 seconds, though
not by Controller action)
Corrective Action:
1. Check fuel level and refill as necessary. (Note: The genset fuel pickup is probably higher than the vehicle engine fuel pickup.)
2. Prime the engine fuel system for one minute (p. 2-4).
3. Check all fuel fittings for fuel and air leaks and tighten as necessary. Reprime.
4. Check the engine air filter and remove any blockage (p. 3-6).
5. Replace the fuel filter (p. 3-8).
6. Conduct a fuel flow test and service as necessary.
7. Remove the governor actuator, test it for proper operation and replace if necessary.
8. Replace the control board.
9. Service the engine.
4-9
Page 44
TABLE 4-1. TROUBLESHOOTING
WARNING
sonal injury or death. Only trained and experienced service personnel with knowledge of fuels, electricity, and machinery hazards should perform genset service. See Safety Precautions.
Some genset service procedures present hazards that can result in severe per-
FIELD OVERLOAD—CODE NO. 38
(During normal voltage regulation Field Voltage exceeded 180 VAC for 10 seconds)
Corrective Action:
1. Reduce the number of air conditioners running at the same time, and other appliances that cause low power factor. (The lower the power factor of a motor or compressor, the more current it draws per kilowatt. The genset Controller, in turn, must boost field voltage to meet the higher demand for current imposed by low power factor.)
2. Have the air conditioners and other appliances checked for proper operation. (A locked compressor rotor can cause a very low power factor.)
3. Test the generator field and stator windings and service as necessary.
GENERATOR ROTOR SHORT—CODE NO. 41
(While flashing the field the Controller sensed that the rotor circuit was shorted to ground)
Corrective Action: See an authorized Onan dealer.
1. Disconnect Generator connector J3/P3 and check for a short to ground at P3-7 and at P3-8. Service or replace brushes, slip rings and rotor as necessary.
2. Replace the control board.
ROM FAULT—CODE NO. 42
(During startup the genset Controller detected a ROM memory error)
Corrective Action: See an authorized Onan dealer.
RAM FAULT—CODE NO. 43
(During startup the genset Controller detected a RAM memory error)
Corrective Action: Replace the control boardSee an authorized Onan dealer.
SPEED SENSE LOST—CODE NO. 45
(After start disconnect the Controller lost speed sense [quadrature zero crossings] for 0.25 seconds)
Corrective Action: See an authorized Onan dealer. See an authorized Onan dealer.
1. Disconnect Generator connector J3/P3 and check for open and shorted field (P3-7—P3-8) and quadrature (P3-3—P3-6) windings. Service or replace brush block, slip rings, rotor or stator as nec- essary.
2. Replace the control board.
4-10
Page 45
TABLE 4-1. TROUBLESHOOTING
WARNING
sonal injury or death. Only trained and experienced service personnel with knowledge of fuels, electricity, and machinery hazards should perform genset service. See Safety Precautions.
Some genset service procedures present hazards that can result in severe per-
LOSS OF FIELD SENSE—CODE NO. 48
(The field sense circuit on the Controller circuit board failed during normal voltage regulation)
Corrective Action: See an authorized Onan dealer.
OVERPRIME—CODE NO. 57
(The local or remote control switch was held in the Prime position for more than 3 minutes)
Corrective Action: Check for and remove any object that may be holding either control switch (remote or local) in the prime position.
4-11
Page 46
4-12
Page 47
5. Specifications
MODEL:
GENSET CONTROL: Integrated Microprocessor-Based Engine and Generator Controller
GENERATOR: Single-Bearing, 4-Pole Rotating Field, 1800 RPM
Power (@1.0 power factor) 10,000 W 12,500 W Voltage 120 / 240 120 / 240 Frequency 60 Hz 60 Hz Number of Phases 1 1 Current 41.7 amps per leg 52.1 amps per leg Line Circuit Breaker 2-pole, 45 amp 2-pole, 50 amp
FUEL CONSUMPTION:
No-load Half-load Full-load
ENGINE: 3-Cylinder In-Line, Water-Cooled, Indirect-Injection (IDI), 4-Stroke Cycle Diesel
Bore 3.43 in (87 mm) Stroke 3.64 in (92.4 mm) Displacement 100.5 in3 (1,647 cc) Compression Ratio 22.6 : 1 Fuel Injection Timing (BTDC) 14.5° Firing Order 132 Fuel Nozzle Injection Pressure 1991 psi (13.731 mPa) Cylinder Compression Test 370 psi (2.55 mPa) minimum
Valve Lash: Intake & Exhaust (cold)
Oil Capacity (with filter)
Cooling System Capacity
DC SYSTEM:
Nominal Battery Voltage
Minimum Battery Capacity CCA (Cold Cranking Amps)
Battery Recharging
WEIGHT: 792 lbs (359 kg) 816 lbs (370 kg)
SIZE (L x W x H): 41.4 x 24.5 x 27 in (105 x 62 x 68.6 cm)
SOUND LEVEL: 68 dB(A) @ 10 ft (3m) & 54 dB(A) @ 50 ft (15m)—in “free field site” @ half load
HDKCA HDKCB
0.11 gph (0.41 lph)
0.48 gph (1.82 lph)
1.01 gph (3.8 lph)
0.11 gph (0.41 lph)
0.48 gph (1.82 lph)
1.2 gph (4.54 lph)
0.0071 to 0.0087 in (0.18 to 0.22 mm)
5.9 quart (5.6 liter)
6.6 quart (6.2 liter)
12 volts
475 amps down to 0° F (−17° C)
650 amps down to −20° F (−29° C)
Installer must provide for battery charging
5-1
Page 48
SPECIFICATIONS
MODEL:
GENSET CONTROL: Integrated Microprocessor-Based Engine and Generator Controller
GENERATOR: Single-Bearing, 4-Pole Rotating Field, 1800 RPM
Power (@1.0 power factor) 10,000 W 12,000 W Voltage 120 / 240 120 / 240 Frequency 60 Hz 60 Hz Number of Phases 1 1 Current 41.7 amps per leg 50 amps per leg Line Circuit Breaker 2-pole, 45 amp 2-pole, 50 amp
FUEL CONSUMPTION:
No-load Half-load Full-load
ENGINE: 3-Cylinder In-Line, Water-Cooled, Indirect-Injection (IDI), 4-Stroke Cycle Diesel
Bore 3.43 in (87 mm) Stroke 3.64 in (92.4 mm) Displacement 100.5 in3 (1,647 cc) Compression Ratio 22.6 : 1 Fuel Injection Timing (BTDC) 14.5° Firing Order 132 Fuel Nozzle Injection Pressure 1991 psi (13.731 mPa) Cylinder Compression Test 370 psi (2.55 mPa) minimum
Valve Lash: Intake & Exhaust (cold)
Oil Capacity (with filter)
Cooling System Capacity
DC SYSTEM:
Nominal Battery Voltage
Minimum Battery Capacity CCA (Cold Cranking Amps)
Maximum Regulated Charging Current
WEIGHT: 816 lbs (370 kg) 816 lbs (370 kg)
SIZE (L x W x H): 41.4 x 24.5 x 27 in (105 x 62 x 68.6 cm)
SOUND LEVEL: 68 dB(A) @ 10 ft (3m) & 54 dB(A) @ 50 ft (15m)—in “free field site” @ half load
HDKCC HDKCD
0.11 gph (0.41 lph)
0.48 gph (1.82 lph)
1.01 gph (3.80 lph)
0.11 gph (0.41 lph)
0.48 gph (1.82 lph)
1.20 gph (4.54 lph)
0.0071 to 0.0087 in (0.18 to 0.22 mm)
5.9 quart (5.6 liter)
6.6 quart (6.2 liter)
12 volts
475 amps down to 0° F (−17° C)
650 amps down to −20° F (−29° C)
20 amps
5-2
Page 49
6. Maintenance Record
Record all periodic and unscheduled maintenance and service. See Section 3. Periodic Maintenance.
HOUR
DATE
METER
READING
MAINTENANCE OR SERVICE PERFORMED
Record the name, address, and phone number of your authorized Onan service center.
6-1
Page 50
6-2
Page 51
Cummins Power Generation
1400 73rd Ave. NE Minneapolis, MN 55432 USA
Phone 1 763 574 5000 Toll-free 1 800 888 6626 Fax 1 763 574 5298 Email www.cumminsonan.com/contact www.cumminsonan.com
CumminsR, OnanR, the “C” logo, and “Performance you rely on.” are trademarks of Cummins Inc.
E2009 Cummins Power Generation, Inc. All rights reserved.
Loading...