Cuisinart CSS-100 Quick Reference
QUICK START GUIDE
Compact Sparkling
Beverage Maker
IMPORTANT!
Do not throw away these instructions.
Read before operating your new Compact Sparkling Beverage Maker.
Keep for future reference.
These helpful hints are intended to be a supplement to the Instruction
Booklet. In order to ensure safe operation and optimum performance,
OPERATING INSTRUCTIONS
please read the entire Instruction Booklet.
1. Fill the beverage bottle with chilled water up to the indicated “WATER FILL
LINE.”
2. Insert the carbonator head into the bottle and screw down firmly until it is
tightly fitted to the bottle (fig. a).
3. Use the toggle to make sure the safety window is fully open on the charger
chamber.
4. Insert a disposable CO
narrow end facing down (fig. b), and ensure the charger is inserted firmly in
place by gently pushing the disposable CO
NOTE: Only use Cuisinart CO2 Chargers powered by SodaSparkle.
charger into the open window of the charger chamber,
2
charger back until you hear a click.
2
5. Place the correctly filled beverage bottle with attached carbonator head in an
upright and stable position on a clean, flat surface. Lower the charger chamber
down onto the carbonator head to engage the activating thread (fig. c). Screw
the charger chamber clockwise onto the carbonator head. The safety window
will automatically close and lock prior to piercing the CO
6. Continue to firmly turn the charger chamber clockwise until you can not tighten
anymore and the CO
bottle and hear a hissing sound and small associated release of excess CO
charger is pierced. You will see the CO2 release into the
2
through the carbonator head safety release valve – a normal part of the
charger.
2
2
carbonation process. NOTE: Wait at least 30 seconds for full carbonation to
take place.
7. Shake the bottle thoroughly for 5 seconds (fig. d) to complete the carbonation
process.
8. Slowly unscrew and remove the charger chamber from the carbonator head.
Slide the safety window open using the slider button and eject the used CO
charger through the window by pushing your index finger through the hole
2
provided.
9. Slowly unscrew the carbonator head and remove, then enjoy your sparkling
water. NOTE: Once opened, use only the standard bottle cap to reseal the
bottle. The sparkling nozzle cap should be used only when carbonating.
If you would like, you can add a natural flavor stick to your 8 oz. glass of
sparkling water for a refreshing, flavored soda (fig. e).
NOTE: Never pour in flavor before carbonating.
10. The supplied bottle cap will maintain a residual pressure and can be placed on
the bottle to keep the contents from going flat (fig. f).
For Best Results
• Use only chilled water for carbonation.
• Always fill bottle to maximum fill
indicator line, never overfill.
Caution
• Never freeze the bottle or its contents.
• Carbonate only once.
• Do not move toggle before
unscrewing charger chamber.
fig. a
fig. b
fig. c
fig. d
fig. e
fig. f
See reverse side for Troubleshooting Guide.
Troubleshooting Guide
Problem Solution
The CO
has not been pierced
charger
2
Water escapes
while carbonating
The water does
not carbonate or
hardly carbonates
• A genuine Cuisinart Single-Use Recyclable CO
– Powered by SodaSparkle™ has not been used.
• The CO
until a click is heard, or has been loaded at an angle.
charger has not been pressed rmly into place
2
Charger
2
• The carbonator head has not been screwed rmly onto
the bottle.
• The charger chamber has not been screwed rmly down
onto the carbonator head.
• The piercing unit inside the carbonator head has been
damaged (in this case please send the complete unit in
for service to an authorized Cuisinart service agent).
• The beverage bottle has been lled above the “Water
Fill Line” indicator.
• The carbonator head has not been screwed on tightly.
• The carbonator head has been unscrewed before
carbonation is complete.
• The unit has been held at an angle while carbonating.
• More than one CO
the same bottle contents (double-carbonating).
charger has been used to carbonate
2
• The charger chamber and carbonator head have been
unscrewed too soon.
• No CO
• A used (empty) CO
charger has been inserted into the charger
2
chamber.
charger has been used. An empty
CO2 charger will have a hole at the tip where it was
2
pierced.
• The water used for carbonation was not cold enough.
• The unit has been used repeatedly in a very short
period of time. Rinse the carbonator head in warm
water for 30 seconds and reuse.
It is difficult or
impossible to insert
or remove the
CO
charger
2
For Customer Service visit www.cuisinart.com or call 1-800-726-0190
See reverse side for Operating Instructions.
• The CO
Cuisinart Single-Use Recyclable CO2 Chargers –
charger may be incompatible. Use only
2
Powered by SodaSparkle™.
• The safety window is not fully open. Use the toggle
to open the safety window completely.
• The charger chamber is still screwed down onto the
carbonator head. Unscrew and remove completely
to enable insertion or ejection of the CO
charger.
2
PG-34103
Loading...