Page 1
Manual Revision #: 07172015 AT
ASSEMBLY
MANUAL
READ AND SAVE MANUAL FOR FUTURE REFERENCE.
Assemble your grill immediately.
Missing or damaged parts should be claimed within 30 days of purchase.
For product inquiries, parts, warranty and troubleshooting support, please call 1-800-309-3452.
www.cuisinartbbqs.com
LIMITED 5-YEAR WARRANTY
Cuisinart®
CERAMIC SMALL SPACES
85-3112-4 (G35801) Propane
85-3113-2 (G35802) Natural Gas
Page 2
THIS MANUAL MUST REMAIN WITH THE PRODUCT AT ALL TIMES
1-800-309-3452
HEAVY ARTICLE NEEDS 2 TO LIFT
To ORDER non-warranty replacement parts or accessories,
or to register your warranty, please visit us on the web at
www.cuisinartbbqs.com
THIS BARBECUE IS FOR OUTDOOR USE ONLY
CUISINART® CUSTOMER CARE HOTLINE
Sharp edges. Wear gloves when assembling
your grill.
Read and follow all safety statements,
assembly instructions, use and care directions
before attempting to assemble and cook.
This manual should be kept with the BBQ at
all times.
CAUTION DANGER
DANGER
CAUTION
CAUTION
Failure to follow all of the Manufacturer’s
instructions could result in hazardous fires,
explosions, property damage, or serious
personal injury or even death.
Follow all leak check procedures carefully prior
to operation of barbecue, even if grill was dealer
assembled. Do not try lighting this BBQ without
reading the Lighting Instructions section of the
Safety and Care Manual that accompanies this
grill.
WARNING
INSTALLER OR
ASSEMBLER/CONSUMER
1. If you smell Gas:
a. Shut off gas to the appliance
b. Extinguish any open flame
c. Open lid
d. If odor continues, keep away from the
appliance and immediately call your gas
supplier or your fire department
2. Do not store or use gasoline or other
flammable liquids or vapours in the vicinity of
this or any other appliance.
3. An LP cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
1. Do not store or use gasoline or other
flammable liquids or vapours in the vicinity of
this or any other appliance.
2. An LP cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
Avoid burns. The stainless steel and steel
surfaces of this barbecue can become extremely
hot, in direct sun and while the barbecue is in
operation.
Page 3
1
HARDWARE PACK
No. Description Part Number Qty.
1 1/4"-20UNCx50 Screw 20120-13050-250 12
2 1/4"-20UNCx16 Screw 20120-13016-250 14
3 1/4”-20UNC Screw G358-0022-9000 8
4 NO.10-24UNC x13 Screw 20124-10013-250 22
5 ST4.2X10 Tapping Screw 22500-42010-137 4
6 φ7 Lock Washer 41400-07000-250 26
7 φ7 Washer 40300-07000-250 26
8 φ5 Lock Washer 41400-05000-250 22
9 φ5 Washer 40300-05000-250 22
10 U-Pin Tool G350-0026-9000 1
1/4”-20UNCx50 Screw
X 12
NO.10-24UNC x13 Screw
X 22
φ5 Washer
X 22
1/4”-20UNCx16 Screw
X 14
ST4.2X10 Tapping Screw
X 4
φ7 Washer
X 26
1/4”-20UNC Screw
X 8
φ7 Lock Washer
X 26
φ5 Lock Washer
X 22
U-Pin Tool
X 1
1 2 3
4 5
6
7
8 9
10
Tools Needed for Assembly
• #2 Phillips screwdriver (long and short)
• ¼” Slotted screwdriver (long and short)
• Adjustable wrench
• Pliers
• Rubber Mallot
For correct hardware assembly, always
position the lock washer between the screw
and the flat washer.
Note: Do not fully tighten all the nuts
during this initial stage
Caution:
Sheet metal can cause injury. Wear gloves when installing this grill.
Lock Washer
Flat Washer
Screw
BEFORE ASSEMBLING THE BARBECUE, READ THESE INSTRUCTIONS CAREFULLY.
Assemble the barbecue on a flat, clean surface. Grill is heavy. Two people are recommended
to complete assembly.
Page 4
2
Item No. Qty. Description Part No.
AA 1 Top Lid G358-2000-01
AB 1 Lid Handle G358-0003-01
AC 2 Lid Handle End Cap G358-0004-01
AD 1 Thermometer G512-0085-01
AE 2 Screw for Top Lid G359-0030-01
AF 2 Lid Bumper, Front G527-0002-02
AG 2 Lid Bumper, Rear G508-0033-01
AH 1 Logo G358-0002-01
BA 1 Burner Box Assembly G358-3100-01
BB 2 Main Burner G525-3800-02
BC 1 Carryover Assembly G358-0400-01
BD 2 3-Pc. Stainless Steel Radiant G618-0056-01
BE 16 Ceramic Stone G535-0045-01
BF 2 Cooking Grate, Burner Box G525-0016-01
BG 1 Warming Rack G353-0026-01
BH 1 Heat Plate Brace, Front G358-0006-01
BI 1 Heat Plate Brace, Back G358-0021-01
BJ 1 Match holder G608-0019-01
CA 1 Manifold assembly - LP G358-4100-01
CB 1 Regulator G513-0017-01
CC1 1 Electronic Ignition Assembly G350-0017-01
CC2 1 Electronic Ignition Battery Cap G515-0030-01
CC3 1 Multi-Spark™ Ignition G525-0028-01
CD 2 Electrode Set, Main Burner G525-0030-03
CE 2 Control Knob G618-0014-01
CF 2 Bezel, Control Knob G525-0012-01
CG 1 Control Panel G358-0008-01
CH 1 Front Brace G358-0011-01
CI 1 Grease Tray G358-0800-01
CJ 1 Grease Cup G416-0015-01
CK 1 Right Track G522-0043-01
CL 1 Left Track G522-0027-01
CM 1 Heat Shield G353-0021-01
CN 1 Upper Back Panel G358-0012-01
CO 1 Lower Back Panel G358-0013-01
PARTS LIST (PROPANE) FOR 85-3112-4 (G35801)
Item No. Qty. Description Part No.
DA 1 Side Shelf Table - Right G358-0700-01
DB 1 Side Shelf Rear Brace - Right G358-0018-01
DC 1 Side Shelf Fascia - Right G358-0017-01
DD 1 Side Shelf Table - Left G358-0600-01
DE 1 Side Shelf Rear Brace - Left G358-0016-01
DF 1 Side Shelf Fascia - Left G358-0015-01
DG 4 Support Bracket, Side Shelf G358-0014-01
EA 1 Cart Side Panel - Left G358-0009-01
EB 1 Cart Side Panel - Right G358-0010-01
EC 1 Bottom Shelf - LP G358-0500-01
ED 2 Wheel with Lock G350-0023-01
EE 2 Wheel G350-0024-01
EF 1 Door Assembly G358-8000-01
EG 1 Door Handle G517-0011-01
EH 2 Door Magnet Assembly G501-00F2-03
F1 1 Hardware Pack G358-B001-01
F2 1 Assembly Manual G358-M001-01
F3 1 Safety and Care Manual G358-M001-02
F4 1 Tank Screw G505-0047-01
F5 1 Ceramic Heat Plate Guide G618-M003-02
Page 5
3
CL
CK
BI
EH
BH
BF
CC3
CG
AF
AE
BG
AB
AA
CI
BC
EC
EB
CH
EA
BB
AD
AH
BA
BE
AC
CA
CB
DE
CN
CO
DA
ED
EE
EF
AG
CD
CJ
CC2
CC1
CE
CF
CM
BD
DB
DC
DD
DF
DG
DG
BJ
EG
AC
EXPLODED DIAGRAM (PROPANE)
FOR 85-3112-4 (G35801)
Hardware
Pack
Tank
Screw
Assembly
Manual
Safe Use
& Care
Manual
Ceramic
Heat Plate
Guide
EXTRAS
F1 F4F2 F3 F5
Page 6
4
PARTS LIST (NATURAL GAS) FOR 85-3113-2 (G35802)
Item No. Qty. Description Part No.
AA 1 Top Lid G358-2000-01
AB 1 Lid Handle G358-0003-01
AC 2 Lid Handle End Cap G358-0004-01
AD 1 Thermometer G512-0085-01
AE 2 Screw for Top Lid G359-0030-01
AF 2 Lid Bumper, Front G527-0002-02
AG 2 Lid Bumper, Back G508-0033-01
AH 1 Logo G358-0002-01
BA 1 Burner Box Assembly G358-3100-01
BB 2 Main Burner G525-3800-02
BC 1 Carryover Assembly G358-0400-01
BD 2 3-Pc. Stainless Steel Radiant G618-0056-01
BE 16 Ceramic Stone G535-0045-01
BF 2 Cooking Grate, Burner Box G525-0016-01
BG 1 Warming Rack G353-0026-01
BH 1 Heat Plate Brace, Front G358-0006-01
BI 1 Heat Plate Brace, Back G358-0021-01
BJ 1 Match holder G608-0019-01
CA 1 Manifold assembly - NG G358-4300-01
CB 1 Natural Gas Hose G501-0099-01
CC1 1 Electronic Ignition Assembly G350-0017-01
CC2 1 Electronic Ignition Battery Cap G515-0030-01
CC3 1 Multi-Spark™ Ignition G525-0028-01
CD 2 Electrode Set, Main Burner G525-0030-03
CE 2 Control Knob G618-0014-01
CF 2 Bezel, Control Knob G525-0012-01
CG 1 Control Panel G358-0008-01
CH 1 Front Brace G358-0011-01
CI 1 Grease Tray G358-0800-01
CJ 1 Grease Cup G416-0015-01
CK 1 Right Track G522-0043-01
CL 1 Left Track G522-0027-01
CM 1 Heat Shield G353-0021-01
CN 1 Upper Back Panel G358-0012-01
CO 1 Lower Back Panel G358-0013-01
Item No. Qty. Description Part No.
DA 1 Side Shelf Table - Right G358-0700-01
DB 1 Side Shelf Rear Brace - Right G358-0018-01
DC 1 Side Shelf Fascia - Right G358-0017-01
DD 1 Side Shelf Table - Left G358-0600-01
DE 1 Side Shelf Rear Brace - Left G358-0016-01
DF 1 Side Shelf Fascia - Left G358-0015-01
DG 4 Support Bracket, Side Shelf G358-0014-01
EA 1 Cart Side Panel - Left G358-0009-01
EB 1 Cart Side Panel - Right G358-0010-01
EC 1 Bottom Shelf - NG G358-0900-01
ED 2 Wheel with Lock G350-0023-01
EE 2 Wheel G350-0024-01
EF 1 Door Assembly G358-8000-01
EG 1 Door Handle G517-0011-01
EH 2 Door Magnet Assembly G501-00F2-03
F1 1 Hardware Pack G358-B001-01
F2 1 Assembly Manual G358-M001-01
F3 1 Safety and Care Manual G358-M001-02
F4 1 Ceramic Heat Plate Guide G618-M003-02
Page 7
5
Hardware
Pack
Assembly
Manual
Safe Use
& Care
Manual
EXTRAS
F1 F2 F3
Ceramic
Heat Plate
Guide
F4
CL
CK
BI
EH
BH
BF
CC3
CG
AF
AE
BG
AB
AA
CI
BC
EC
EB
CH
EA
BB
AD
AH
BA
AC
AC
CA
CB
DE
CN
CO
DA
ED
EE
EF
AG
CD
CJ
CC2
CC1
CE
CF
CM
BD
DB
DC
DD
DF
DG
DG
BJ
EG
BE
EXPLODED DIAGRAM (NATURAL GAS)
FOR 85-3113-2 (G35802)
Page 8
6
Separate the 2 different types of Wheels,
2 Locking Wheels (ED) and 2 Regular Wheels
(EE).
Insert the U Pin Tool (#10) into one of the
Regular Wheels (EE), as shown in image B.
Attach the Regular Wheel (EE) to the front of
the Bottom Shelf (EC), and use the U Pin Tool
(#10) to secure and tighten.
Repeat for remaining 3 wheels (EE and ED).
NOTE: Regular Wheels (EE) need to be
assembled to the front of the Bottom
Shelf (EC), and Wheels with Lock (ED)
need to be assembled to the back of
the Bottom Shelf (EC), as shown in
image A.
Ensure that the wheels are rmly locked in the
“ON” position before continuing.
Assemble the Left Cart Side Panel (EA) and the
Right Cart Side Panel (EB) to the Bottom Shelf
(EC).
6
6
X 1
X 6 X 6 X 6
YOU WILL NEED:
YOU WILL NEED:
1.
2.
Back view
Front view
Close up
Close up
ED
EE
EE
EB
EA
EC
10
EC
EB
10
2 6 7
B
B
A
A
ASSEMBLY INSTRUCTIONS
EC
Page 9
7
Assemble the Lower Back Panel (CO) to the
Left and Right Cart Side Panels (EA and EB).
Attach the Front Brace (CH) to the Left and
Right Cart Side Panels (EA and EB). The top of
the Front Brace (CH) can be identied by two
clips located on the top left, and right side of
this part, as shown in B.
TIP: One person should align the left side,
while the second person assembles the
right side.
6
X 4 X 4 X 4
YOU WILL NEED:
3.
Front View
Back view
Close up
Close up
CO
EB
EB
EA
CO
CH
CH
EB
EA
EA
2 6 7
B
A
A
B
ASSEMBLY INSTRUCTIONS
4.
EC
6
X 4 X 4 X 4
YOU WILL NEED:
4 8 9
Page 10
8
ASSEMBLY INSTRUCTIONS
5.
Assemble the Heat Shield (CM) to the Left and
Right Cart Side Panels (EA and EB).
a. Position the Top Lid and Burner Box
Assembly (A and B) onto Cart Assembly (C),
as shown.
6.
Front view
Front view
A
Close up
B
6
X 4
YOU WILL NEED:
5
THIS STEP REQUIRES 3 PEOPLE. DO NOT
ATTEMPT ALONE. EXTREMELY HEAVY!
A
C
A+B
EA
EB
CM
EA
CM
NOTE: Remember to remove the tie holding
the electrode wires and pull them down
into the cart.
Page 11
9
ASSEMBLY INSTRUCTIONS
b. Assemble Burner Box Assembly (A and B) to
the Left and Right Cart Side Panels (EA and
EB), as shown.
6.
Back view
A
Close up
B
7.
Attach the Upper Back Panel (CN) to both the
Left and Right Cart Side Panels (EA and EB).
DO NOT tighten screws until all hardware
has been positioned.
Back view
EB
EA
EA
EA
CN
CN
B
A+B
Close up - left outside view
6
6
X 4
X 4
X 4
X 4
X 4
X 4
YOU WILL NEED:
YOU WILL NEED:
2
1
6
6
7
7
EB
Page 12
10
ASSEMBLY INSTRUCTIONS
8.
b. Assemble the back of the Left and Right
Tracks (CL and CK) to the Upper Back Panel
(CN), as shown in gure C.
a. Assemble the Left and Right Tracks (CL and
CK) for the Grease Tray (CI), as shown in
gure A, B and C.
Back view
Front view
Back view
A
B
C
YOU WILL NEED:
CK
6
X 2 X 2 X 2
4 8 9
TIP: Both the Left and Right Tracks (CL and
CK) should be inserted into the two clips
located on the top of the Front Brace (CH),
as shown in gure B.
CL
CN
CH
CG
CN
CK CL
Page 13
11
ASSEMBLY INSTRUCTIONS
b. Assemble the hardware (#3) to the right
upper side panel of the Burner Box Assembly
(BA).
d. Assemble the hardware (#3) to the left upper
side panel of the Burner Box Assembly (BA).
a. Assemble the Side Shelf Support Brackets
(DG) to the right upper side panel of the
Burner Box Assembly (BA).
9.
Front, right Side view
A
c. Assemble the Side Shelf Support Brackets
(DG) to the left upper side panel of the
Burner Box Assembly (BA).
B
D
C
Front, right side view
Front, left side view
Front, left side view
6
X 4 X 4 X 4
YOU WILL NEED:
1 6 7
6
X 4 X 4 X 4
YOU WILL NEED:
1 6 7
6
6
X 2
X 2
YOU WILL NEED:
YOU WILL NEED:
3
3
TIP: All Side Shelf Support Brackets are the
same.
BA
DG
DG
BA
DG
DG
BA
3
3
3
3
BA
Page 14
12
ASSEMBLY INSTRUCTIONS
10.
A
B
C
Front view, left side shelf
Front view, left side shelf
Back view, left side shelf
Close up
a. Assemble the Side Shelf Fascia (DF) to the
Left Side Shelf Table (DD), as shown in gure
A and B.
b. Assemble the Side Shelf Table Rear Brace
(DE) to the Left Side Shelf Table (DD), as
shown in gure C and D.
c. Repeat steps a to c for the Right Side Shelf
Assembly (DA, DB, and DC).
YOU WILL NEED:
YOU WILL NEED:
YOU WILL NEED:
6
6
6
X 1
X 3
X 3
X 1
X 3
X 3
X 1
X 3
X 3
4
4
4
8
8
8
9
9
9
DF
DD
DD
DF
DD
DE
NOTE: Beware of sharp edges.
NOTE: Beware of sharp edges.
NOTE: Beware of sharp edges.
D
DE
Page 15
13
ASSEMBLY INSTRUCTIONS
11.
b. Assemble the hardware (#3) to the front of
the Right Side Shelf Fascia (DC).
c. Assemble the hardware (#3) to the back of
the Right Side Shelf Rear Brace (DB).
A
B
C
D
Front, right side view
View under right side shelf
Front, right side view
Back, right side view
a. Position the Right Side Shelf Assembly (DA,
DB and DC) onto the hardware tightened in
Step 9B, as shown in gure A and B.
6
6
X 1
X 1
YOU WILL NEED:
YOU WILL NEED:
3
3
DA
DC
BA
DA
DB
DC
DC
DA
DA
3
3
BA
DB
Page 16
14
ASSEMBLY INSTRUCTIONS
12.
b. Assemble the hardware (#3) to the front of
the Left Side Shelf Fascia (DF).
A
B
C
D
Front, left side view
View under left side shelf
Front, left side view
Back, left side view
a. Position the Left Side Shelf Assembly (DD,
DE and DF) onto the hardware tightened in
Step 9D, as shown in gure A and B.
c. Assemble the hardware (#3) to the back of
the Left Side Shelf Rear Brace (DE).
6
6
X 1
X 1
YOU WILL NEED:
YOU WILL NEED:
3
3
3
3
BA
DD
DF
BA
DD
DF
DE
DF
DD
DD
DE
Page 17
15
b. Feed the Electronic Ignition Assembly (CC1)
through the opening in the Right Cart Side
Panel (EB) and secure using the nut.
13.
ASSEMBLY INSTRUCTIONS
a. Remove the Electronic Ignition Battery Cap
(CC2) and the plastic nut from the Electronic
Ignition Assembly (CC1).
c. Insert one “AA” battery into the battery
compartment with the positive end facing
outward, as shown. Secure using the
Electronic Ignition Battery Cap (CC2).
d. Insert the two Electrode Set, Main Burner
(CD) wires and the two ignition button wires
(CC3) into the Electronic Ignition Assembly
(CC1), as shown in gure D.
CD
CD
CC1
D
A
B
C
-
+
TIP: The Electrode set, Main Burner (CD), the
two Ignition Button wires (CC3) can be
found attached to the control panel heat
shield (CG), as shown in gure C.
NOTE: All main burner electrode wire
connection points are the same size.
CC3
CC3
CC1
CC2
Plastic Nut
EB
CC2
CC1
CG
Right side panel, inside view
Right side panel, outside view
Right side panel, inside view
Page 18
16
ASSEMBLY INSTRUCTIONS
14.
Bottom of door
Top of door
a. Assemble the Door Assembly (EF) to the
Bottom shelf (EC) by inserting the xed pin
(bottom of door) into the hole provided (gure
B).
b. Assemble the top of the Door Assembly (EF)
to the Control Panel (CG) by pressing in the
door support pin and aligning with the hole
located on the top right corner of the door.
A
B
C
15.
YOU WILL NEED:
6
X 2 X 2 X 2
4 8 9
TIP: Use a paint scraper to press-in the support
pin. The support pin will lock into position
when the door is assembled correctly.
EF
EG
Assemble the Door Handle (EG) to the Door
Assembly (EF), as shown in gure A.
A
Front view
EF
EC
EF
CG
EF
EC
EB
EA
Page 19
17
ASSEMBLY INSTRUCTIONS
16.
a. Position the Grease tray (CI) onto the Left
and Right Tracks (CL and CK), as shown.
b. Place the Grease Cup (CJ) onto the tracks,
located on the underside of the Grease Tray
(CI).
CI
CJ
CK
CL
Back view
Page 20
18
ASSEMBLY INSTRUCTIONS
17.
To assemble the Ceramic Heat Plates,
locate the following:
Put these parts aside for Step E:
3-pc. Stainless Steel
Radiant (BD)
Hitch Pin
Ceramic
Stone (BE)
Connector
a. Remove the 2 hitch pins and connectors
from the 3-pc. Stainless Steel Radiant (BD),
as shown in Figure A and B.
b. Detach the right and left frames from the top
of the stainless steel radiant (BD), as shown
in gure D.
A
D
Close up
Close up
X 2
X 2
X 16
X 2
B
C
ATTENTION: For the purpose of safe
shipping and transit, the Stainless Steel
Radiants and the Ceramic Stones,
have been shipped separately, and
will require assembly. Use care when
handling the carton labeled Ceramic
Stones.
Page 21
19
ASSEMBLY INSTRUCTIONS
d. Secure the Ceramic Stones (BE) in place by
assembling the right frame back onto the
Stainless Steel Radiant (BD), as shown in
gure F and G.
E
F
G
17.
c. Insert the Ceramic Stones (BE) into the
openings on the right side of the Stainless
Steel Radiant (BD).
NOTE: The flat side of the Ceramic Stones
(BE) should be facing up.
BE
BD
BE
BD
Page 22
20
ASSEMBLY INSTRUCTIONS
17.
You will need these parts from Step A:
Hitch PinConnector
e. Secure using one set of the connectors and
hitch pins, removed in step 17A, as shown in
gures H – J.
f. Repeat steps C and D for the left side of the
Stainless Steel Radiant (BD) to complete
assembly. Figure K shows the assembled
Ceramic Heat Plate.
H
I
K
Close up
X 1X 1
BD
BE
J
Page 23
21
ASSEMBLY INSTRUCTIONS
L
M
17.
g. Once assembled, position Ceramic Heat
Plates (BD + BE) into the Burner Box (BA),
as shown in gure L and M.
NOTE: The ports in the middle of the heat plate
should be at the front of the burner
box. Hitch Pins should be on the
underside of the Ceramic Heat Plate.
BE
BD
Page 24
22
ASSEMBLY INSTRUCTIONS
18.
A
B
a. Place the Cooking Grates (BF) into the
Burner Box (BA), as shown in gure A.
b. Assemble the Warming Rack (BG) by
inserting the two xed pins into the two holes
provided on the Burner Box back panel (BA),
as shown in gure B.
BA
BG
BA
BF
Page 25
23
FOR PROPANE MODELS ONLY.
For natural gas model, follow step 20.
a. Position the 20 lb propane tank onto the
bottom shelf (EC), and secure using the
bolt (F4) (already attached) located on the
underside of the bottom shelf, as shown in
gure B.
b. Attach the Regulator coupling nut to the LP
cylinder valve. Be careful not to cross thread.
Hand tighten only.
c. Perform Leak Test. See page 5 of the
Cuisinart
®
Safety and Care Manual.
ATTENTION: For your families safety,
do not attempt to light this BBQ until
you have reviewed pages 4-7 of the
Cuisinart
®
Safety & Care Manual.
All Safety and Leak Test MUST BE
PERFORMED BY THE END USER,
prior to lighting this BBQ.
WARNING Do not store extra
propane tanks within BBQ cart.
ASSEMBLY INSTRUCTIONS
19.
EC
F4
A
B
View from underneath barbecue
CB
Page 26
24
ATTENTION: For your families safety,
do not attempt to light this BBQ until
you have reviewed pages 4-7 of the
Cuisinart
®
Safety & Care Manual.
All Safety and Leak Test MUST BE
PERFORMED BY THE END USER,
prior to lighting this BBQ.
FOR NATURAL GAS MODEL ONLY.
a. Attach the Natural Gas Hose (CB) to the
manifold (CA), as shown.
b. Perform Leak Test. See page 6 of the
Cuisinart
®
Safety and Care Manual.
CB
CB
CA
20.
ATTENTION: In order to complete
installation of your Natural Gas BBQ
a 1/2” or 3/8” adapter may be required
to connect your BBQ’s Natural Gas
hose to your home gas supply.
Contact your Natural Gas supplier to
purchase the necessary part.
ASSEMBLY INSTRUCTIONS
Front view
Quick Connector
Natural Gas
Home Supply
A
B
WARNING: For all new, at home,
natural gas connections please
contact a certified gas technician to
install your natural gas barbecue.
Page 27
Visit www.cuisinartbbqs.com
to complete product registration.
Cuisinart® is a registered
trademark used under license
© 2016 Trileaf Distributions Trifeuil
Cuisinart® Gourmet Barbecues Customer Service:
1-800-309-3452
Join the conversation
facebook.com/cuisinartbbqs twitter.com/cuisinartbbqs
Loading...