Cub Cadet Z-Force Pro Operator's Manual
Safe Operation Practices • Set-Up • Operation • Service • Troubleshooting
OperatOr’s Manual
Tractor
Z-Force Pro
Table of Contents
Safe Operation Practices ........................................ 2
Assembly & Set-Up .................................................. 8
Controls & Operation .............................................11
Service .....................................................................16
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
NOTE: This Operator’s Manual covers several models. Features may vary by model. Not all features in this manual are applicable to all
models and the model depicted may differ from yours.
Printed In USA
Troubleshooting .................................................... 22
Replacement Parts ................................................ 23
Attachments & Accessories .................................. 23
Warranty ................................................... Back Page
Form No. 769-11052
(August 19, 2015)
Important Safe Operation Practices
WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or
property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to
comply with these instructions may result in personal injury. When you see this symbol, HEED ITS WARNING!
CALIFORNIA Proposition 65
WARNING! Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the
State of California to cause cancer and birth defects or other reproductive harm.
WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of
California to cause cancer and reproductive harm. Wash hands after handling.
WARNING! This machine is equipped with an internal combustion engine and should not be used on or near any unimproved
forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrestor meeting
applicable local or state laws (if any). If a spark arrestor is used, it should be maintained in effective working order by the operator. In the
state of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar
laws. Federal laws apply on federal lands. A spark arrestor for the muffler is available through your nearest engine authorized service
dealer or contact the service department, P.O. Box 361131, Cleveland, Ohio 44136-0019.
This spark ignition system complies with Canadian ICES-002.
2
DANGER! The engine manufacturer has supplied an engine owner’s manual for information regarding US Environmental Protection
Agency (EPA) and California Air resources Board (CARB) regulations relating to emission control systems, maintenance, and warranty. Making
any unauthorized alterations or modifications to the engine, fuel, or venting systems may violate EPA and/or CARB regulations. Further
information may be obtained from the engine manufacturer.
DANGER! This machine was built to be operated according to the safe operation practices in this manual. As with any type of power
equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating hands
and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.
Training
1. Read the Operator’s manual and other training material. If the
operator(s) or mechanic(s) cannot read English it is the owner’s
responsibility to explain this material to them.
2. Become familiar with the safe operation of the machine, operator
controls, and safety signs.
3. All operators and mechanics should be trained to operate or
service the equipment. The owner is responsible for training
them.
4. Never let children under the age of 16 or untrained people
operate or service the equipment. Local regulations may further
restrict the age of the operator.
5. The owner/operator can prevent and is responsible for accidents
or injuries occurring to them, other people or property.
General Operation
1. Read, understand, and follow all instructions on the machine and
in the manual(s) before attempting to assemble and operate. Keep
this manual in a safe place for future and regular reference by each
operator and for ordering replacement parts.
2. Be familiar with all controls and their proper operation. Know how
to stop the machine and disengage the controls quickly.
3. Do not allow anyone to operate or maintain this machine who has
not read the manual. Never permit children under the age of 16 to
operate this machine.
4. Do not remove any shields, guards, labels or safety devices. If
a shield, guard, label or safety device is damaged or does not
function, repair or replace it before operating the machine.
5. To help avoid blade contact or a thrown object injury, keep
bystanders, helpers, children and pets at least 75 feet from the
machine while it is in operation. Stop machine if anyone enters
the area.
6. Thoroughly inspect the area where the equipment is to be used.
Remove all stones, sticks, wire, bones, toys, and other foreign
objects that could be picked up and thrown by the blade(s).
Thrown objects can cause serious personal injury.
7. Evaluate the terrain to determine what accessories and
attachments are needed to properly and safely perform the job.
Only use accessories and attachments approved by the machine
manufacturer.
8. Plan your mowing pattern to avoid discharge of material toward
roads, sidewalks, bystanders and the like. Also, avoid discharging
material against a wall or obstruction which may cause discharged
material to ricochet back toward the operator.
2
9. Always wear appropriate clothing and personal protective
equipment (e.g. safety glasses, long pants, gloves, hearing
protection , safety shoes, hard hat) when operating or maintaining
this machine. Long hair, loose fitting clothing or jewelry may
get entangled in moving parts. Follow all federal, state and local
guidelines regarding the use of personal protective equipment.
10. Be aware of the mower and attachment discharge direction and
do not point it at anyone. Do not operate the mower without the
discharge cover or entire grass catcher in its proper place.
11. Do not put hands or feet near rotating parts or under the cutting
deck. Contact with the blade(s) can amputate hands and feet.
12. A missing or damaged discharge cover can cause blade contact or
thrown object injuries.
13. Stop the blade(s) when crossing gravel drives, walks, or roads and
while not cutting grass.
14. Watch for traffic when operating near or crossing roadways. This
machine is not intended for use on any public roadway.
15. Do not operate the machine while under the influence of alcohol
or drugs.
16. Mow only in daylight or good artificial light.
17. Never carry passengers.
18. Back up slowly. Always look down and behind before and while
backing to avoid a back-over accident.
19. Slow down before turning. Operate the machine smoothly. Avoid
erratic operation and excessive speed. Be aware of your direction
of travel to avoid accidents.
20. Disengage blade(s), set parking brake, stop engine and wait until
the blade(s) come to a complete stop before removing grass
catcher, emptying grass, unclogging chute, removing any grass or
debris, or making any adjustments.
21. Never leave a running machine unattended. Always stop on level
ground, turn of f blade(s), place drive speed control pedals in
neutral, set parking brake, stop engine and remove key before
leaving the operator position.
22. Use extra care when loading or unloading the machine on a
trailer or truck. The machine should not be driven on unstable,
unsecured or inadequate ramps because the machine could tip
over causing serious personal injury.
23. Check overhead clearances carefully before driving under low
hanging tree branches, wires, door openings etc., where the
operator and/or ROPS may be struck which could result in serious
injury and/or machine tip over.
24. Muffler and engine become hot and can cause a burn. Do not
touch.
25. Disengage the blades, set the parking brake to the ‘ON’ position
and make sure the speed control pedals are in the neutral
position before attempting to start the engine. Only start the
engine from the operator’s position.
26. Do not attempt to mow unusually tall, dry grass (e.g., pasture) or
piles of dry leaves. Dry grass or leaves may contact the engine
exhaust and/or build up on the mower deck presenting a potential
fire hazard.
27. Do not stop or park the machine over dry leaves, grass, debris or
other combustible material.
28. Never attempt to operate the machine without the mowing deck
attached; the machine could tip over.
29. Keep the machine and especially the engine exhaust system and
hydraulic components clean and free of grease, grass and leaves
to reduce the potential for overheating and fire.
30. Allow the machine to cool at least 5 minutes before storing.
31. Use only accessories and attachments approved for this machine
by the machine manufacturer. Read, understand and follow all
instructions provided with the approved accessory or attachment.
32. Data indicates that operators, age 60 years and above, are involved
in a large percentage of riding mower-related injuries. Operators
should evaluate their ability to operate this machine safely enough
to protect themselves and others from serious injury.
33. Do not operate or start machine if there is fuel or oil leaks; repair
immediately.
34. When looking for oil leaks, never run your hand over hydraulic
hoses, lines or fittings. Never tighten or adjust hydraulic hoses,
lines or fittings while the system is under pressure. If highpressure oil penetrates the skin seek immediate medical attention
or gangrene and permanent damage may result. Do not check for
hydraulic leaks with your hands, use paper or cardboard instead.
Wear gloves and safety glasses when checking for leaks.
35. Do not operate machines that have been damaged or have not
been properly maintained. If the machine has been damaged,
then have it repaired.
36. When operating this machine in the forward direction, do not
allow the speed control pedals to return to the neutral position on
their own. Always operate them smoothly and avoid any sudden
movements of the pedals when starting or stopping.
37. If situations occur which are not covered in this manual use
care and good judgement. Contact your customer service
representative for assistance.
Slope Operation
Slopes are a major factor related to loss of control and tip-over accidents
that can result in severe injury or death. All slopes require extra caution.
If you cannot back up the slope or if you feel uneasy on it, do not mow it
or drive on the slope.
For your safet y, use the slope gauge included as part of this manual to
measure slopes before operating this machine on a sloped or hilly area. If the
slope is greater than 20 degrees/35 percent as shown on the slope gauge, do
not operate this machine on that area or serious injur y could result.
Do:
1. Mow across slopes, not up and down. Exercise extreme caution
when changing direction on slopes.
2. Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven
terrain could over turn the machine. Tall grass can hide obstacles.
3. Use slow speed. Choose a low enough speed so that you will not
have to stop while on the slope. Avoid starting or stopping on a
slope. If the tires are unable to maintain traction, disengage the
blades and proceed slowly and carefully straight down the slope.
4. Keep all movements on the slopes slow and gradual. Do not
make sudden changes in speed or direction. Rapid acceleration
could cause the front of the machine to lift and rapidly flip over
backwards, which could cause serious injur y or death.
5. Follow the manufacturer’s recommendations for wheel weights or
counterweights to improve stability.
6. Use extra care with grass catchers or other attachments. These can
change the stability of the machine.
Do Not:
1. Do not turn on slopes unless necessary; then turn slowly uphill
and use extra care while turning.
2. Do not mow near drop-offs, ditches or embankments. The
machine could suddenly turn over if a wheel is over the edge of a
cliff, ditch, or if an edge caves in.
3. Do not operate on slopes or near the edge of water such as a lake,
pond, river or stream where the machine could slip, tip or roll-over
into the water.
4. Do not try to stabilize the machine by putting your foot on the
ground.
3Section 2 — impo rtant Safe operation practiceS
5. Do not use a grass catcher on slopes steeper than 15 degrees.
6. Do not mow on wet grass. Reduced traction could cause sliding
and/or loss of control.
7. Do not tow heavy pull behind attachments (e.g. loaded dump
cart, lawn roller, etc.) on slopes greater than 5 degrees. When
going downhill, the extra weight tends to push the machine and
may cause loss of traction and loss of control (e.g. machine may
speed up, braking and steering ability are reduced, attachment
may jack-knife and cause machine to overturn).
Children
1. Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the machine
and the mowing activity. They do not understand the dangers.
Never assume that children will remain where you last saw them.
a. Keep children out of the mowing area and in watchful care
of a responsible adult other than the operator.
b. Be alert and turn machine off if a child enters the area.
c. Always look behind and down for small children. Use slow
speed.
d. Never carry children, even with the blade(s) shut off. They
may fall off and be seriously injured or inter fere with safe
machine operation.
e. Use extreme care when approaching blind corners,
doorways, shrubs, trees or other objects that may block your
vision of a child who may run into the path of the machine.
f. To avoid back-over accidents, always disengage blades
before traveling in reverse.
g. Keep children away from hot or running engines. They can
suffer burns from a hot muffler.
h. Remove key when machine is unattended to prevent
unauthorized operation.
2. Never allow children under 16 years of age to operate this machine.
Children 16 and over should read and understand the instructions and
safe operation practices in this manual and on the machine and should
be trained and supervised by an adult.
Towing
1. Do not tow heavy tow-behind attachments (e.g. loaded dump
cart, lawn roller, etc.) on slopes greater than 5 degrees.
2. Tow only with a machine that has a hitch designed for towing. Do
not attach towed equipment except at the hitch point.
3. Follow the manufacturer’s recommendation for weight limits for
towed equipment and towing on slopes.
4. Never allow children or others in or on towed equipment.
5. On slopes, the weight of the towed equipment may cause loss of
traction and loss of control.
6. Travel slowly and allow extra distance to stop.
7. Make wide turns to avoid jack knifing
Transporting Machines
1. This machine is not intended for use on public roads. Machines
operated on public roads must comply with state & local
ordinances, SAE J137, and ANSI/ASABE S279 (lighting and marking
requirements).
2. Use care when loading or unloading machines onto trailers and trucks.
3. If ramps are used, they must be full width, stable, have an
adequate capacity rating and be secured to the trailer or truck.
Ramp angle should not exceed 15 degrees and trailer or truck
should be parked on level terrain.
4. Machines must be secured onto trailers and trucks with straps,
chains, cables, ropes, or other means deemed adequate for that
purpose. The front and rear of the machines must be secured to
the trailer or truck in both the lateral and vertical directions.
4 Section 2 — impo rtant Safe operation practiceS
Operator Protective System (OPS)
1. This machine is equipped with an Operator Protective System
(OPS), which includes:
a. A Roll Over Protective Structure (ROPS) of the fixed or
folding configuration.
b. Seat belt assembly with retractable function.
2. ROPS are structures designed to provide a crush-resistant space
for the operator when properly seat-belted within the designated
seating area of the machine in the event of a machine tip-over
or roll-over. Folding ROPS shall be used in their fully upright and
locked configurations except in those circumstances whereby
they need to be momentarily folded-down to avoid contact with
items such as tree limbs, clothes lines, guy wires, utility poles,
buildings, etc. At other times and conditions, ROPS shall be in their
fully upright and locked configurations.
DANGER: Damaged ROPS must be replaced prior to
operator use!
3. Seat belts shall be used and shall be properly fastened about the
operator’s waist at all times, except when the ROPS are:
a. Not properly installed and/or not properly secured onto
the machine.
b. Damaged in such manner that their structural integrity has
been compromised.
c. Not in their fully upright and locked position.
4. Seat belts are attached to the movable portion of the seat when
suspension seats are utilized, and therefore the seat-mounting
base must be secured to its pivot means and the pivot means
latched to the frame of the machine. Seat belts are attached to the
seat or the frame of the machine when non-suspension (standard)
seats are provided, however, if a suspension kit is added to a seat,
the seat belt must be attached to the movable portion of the
seat or suspension mechanism, the seat-mounting base must be
secured to its pivot means, and the pivot means be latched to the
frame of the machine.
DANGER: If ROPS are folded down or missing, seat
belts shall not be fastened. Worn or damaged seat
belt assemblies must be replaced prior to operator
use.
5. A brush guard or canopy may deflect tree limbs, clothes
lines, and other obstacles that otherwise could come in
contact with the ROPS. Contact of ROPS and/or canopies
by items such as tree limbs, clothes lines, guy wires, and
buildings, could create hazardous conditions whereby
the machine could experience a tip-over or roll-over. A
canopy may provide protection for the operator from some
environmental exposure (sunlight, rain, etc.).
6. The ROPS and seat belt are integral parts of this machine and
should not be tampered with, modified in any manner, or
removed.
7. Inspect the ROPS and seat belt assemblies on a regular basis for
damage and improper operation. Replace all components that
are damaged or are not functioning properly with authorized
replacement parts.
8. The ROPS extends above and behind the operator position, and
therefore the operator must be aware of potential contact of
the ROPS with items such as trees, buildings, doorways, clothes
lines, utility wires, etc., that could cause the machine to tip-over
or rollover. Use caution in (or avoid) areas where the ROPS could
come in contact with any structures, trees, etc.
9. Inspect the ROPS and seat belt assemblies on a regular basis for
damage and improper operation. Replace all components that
are damaged or are not functioning properly with authorized
replacement parts.
10. Failure to use the seat belt properly could result in serious injury
or death if an accidental overturn occurs. In order for the ROPS to
be effective, the seat belt must be securely fastened around the
operator at all times when the operator is on the machine. Contact
with the ROPS during an overturn could cause serious injury or death.
11. The ROPS will not prevent machine from tip -overs or roll-overs.
12. Do not assume ROPS will protect you in a tip-over or roll-over.
Injuries may still occur.
Hydraulic Devices and Systems
Hydraulic fluid escaping under pressure may have sufficient force to
penetrate skin and cause serious injury. If foreign fluid is injected into
the skin or eyes, see immediate medical attention or gangrene and
permanent damage may result.
WARNING! Keep body and hands away from
pinholes or nozzles that could inject hydraulic fluid
under high pressure. Use paper or cardboard, not
your hands, to search for leaks! Wear gloves and
safety glasses.
Safely relieve all pressure in the system before performing any work on
the system, and make sure that:
• The ignition switch is OFF
• The key is removed
• The engine spark plug wire(s) removed
• All connections to the negative terminal of the battery are removed
• The park brake is set
• All by-pass valves, if so equipped, are open
• Hydraulic controls are actuated to release pressure on pumps,
cylinders, etc. If “float” positions are available, they should be used.
After the above operations are completed, it should be safe to begin
disconnecting the lines or components. It is still a good idea to cover the
connection with a cloth shield and then gently loosen connections.
WARNING! Make sure all hydraulic fluid connections
are tight and all hydraulic hoses and lines are in
good condition before applying pressure to the
system.
Service
Safe Handling of fuel
1. To avoid personal injury or property damage use extreme
care in handling fuel. Fuel is extremely flammable and the
vapors are explosive. Serious personal injury can occur
when fuel is spilled on yourself or your clothes which can
ignite. Wash your skin and change your closes immediately.
a. Use only approved containers.
b. Never fill containers inside a vehicle or a truck or trailer bed
with a carpeted or plastic liner. Always place containers on
the ground away from your vehicle before fueling.
c. When practical, remove machines from the truck or trailer
and refuel it on the ground. If this is not possible, then refuel
equipment on a trailer with a portable container rather than
from a fuel dispenser nozzle.
d. Keep nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete. Do
not use a nozzle lock-open device.
e. Extinguish all cigarettes, cigars, pipes and other sources of
ignition.
f. Never fuel machine indoors or near ignition sources.
g. Never remove fuel cap or add fuel while the engine is
hot or running. Allow engine to cool at least two minutes
before refueling.
h. Never over fill fuel tank. Fill tank to no more than ½ inch below
bottom of f iller neck to allow space for expansion.
i. If necessary, use a funnel to avoid spillage.
j. Replace fuel cap and tighten securely.
k. If fuel is spilled, wipe off the engine and equipment. Wait 5
minutes before starting the engine.
l. To reduce fire hazards, keep machine free of grass, leaves,
or other debris build-up. Clean up oil and fuel spillage and
remove any fuel soaked debris.
m. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light as on a water
heater, space heater, furnace, clothes dryer or other gas
appliance.
General Service
1. Never run an engine indoors or in a poorly ventilated area. Engine
exhaust contains carbon monoxide, an odorless, and deadly gas.
2. Before cleaning, repairing, or inspecting, make certain the blade(s)
and all moving parts have stopped. Disconnect the spark plug
wires and remove the key from the ignition to prevent unintended
starting.
3. Periodically check to make sure the blades come to complete stop
within approximately (7) seven seconds after operating the blade
disengagement control. If the blades do not stop within this time
frame, your machine should be serviced.
4. Never tamper with the safety interlock system or other safety
devices.
5. Regularly check the safety interlock system for proper function, as
described later in this manual. If the safety interlock system does
not function properly, have your machine serviced.
6. Check brake operation frequently as it is subjected to wear during
normal operation. Adjust and service as required.
7. Check the blade(s) and engine mounting bolts at frequent intervals
for proper tightness. Also, visually inspect blade(s) for damage
(e.g., excessive wear, bent, cracked). Replace the blade(s) with
the original equipment manufacturer’s (O.E.M.) blade(s) only,
listed in this manual. “Use of parts which do not meet the original
equipment specifications may lead to improper per formance and
compromise safety!”
8. Mower blades are sharp. Wrap the blade or wear gloves, and use
extra caution when servicing them.
9. Keep all nuts, bolts, and screws tight to be sure the equipment is
in safe working condition.
10. After striking a foreign object (or if abnormal vibration occurs), stop
the blades and engine and thoroughly inspect the machine for any
damage. Make necessary repairs before resuming operation.
11. Never attempt to make adjustments or repairs to the machine
while the engine is running.
5Section 2 — impo rtant Safe operation practiceS
12. Grass catcher components and the discharge cover are subject
to wear and damage which could expose moving par ts or allow
objects to be thrown. For safety protection, frequently check
components and replace immediately with original equipment
manufacturer’s (O.E.M.) parts only, listed in this manual. “Use of
parts which do not meet the original equipment specifications
may lead to improper performance and compromise safety!”
13. Do not change the engine governor settings or over-speed the
engine. The governor controls the maximum safe operating speed
of the engine.
14. Maintain or replace safet y and instruction labels, as necessar y.
15. Observe proper disposal laws and regulations for gas, oil, etc. to
protect the environment.
Do not modify engine
To avoid serious injury or death, do not modify engine in any way.
Tampering with the governor setting can lead to a runaway engine and
cause it to operate at unsafe speeds. Never tamper with factory setting
of engine governor.
Notice Regarding Emissions
This machine is equipped with an engine that is certified to federal EPA
emission standards for non-road engines and equipment, and where
applicable to California Air Resources Board (CARB) emission standards.
The engine owner’s manual is supplied by the engine manufacturer,
and provides additional information relating to the emission system,
warranty, maintenance of the engine in accordance with EPA and/or
CARB regulations. Making any unauthorized alterations or modifications
to the engine, fuel, or venting systems may violate EPA and CARB
regulations.
When required, models are equipped with low permeation fuel lines
and fuel tanks for evaporative emission control. California models may
also include a carbon canister. Please contact Customer Support for
information regarding the evaporative emission control configuration
for your model.
This machine is designed to run on regular, unleaded gasoline, 87
octane or higher. Never use gasoline containing methanol or gasoline
containing more than 10% ethanol (i.e., E15 or E85 fuels) because the fuel
system may be damaged.
Safety Symbols
This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before
attempting to assemble and operate.
Symbol Description
READ THE OPERATOR’S MANUAL(S)
Read, understand, and follow all instructions in the manual(s) before attempting to assemble and
operate
MAX 20˚
WARNING — ROTATING BLADES
Do not put hands or feet near rotating parts or under the cutting deck. Contact with the blade(s) can
amputate hands and feet.
WARNING — THROWN OBJECTS
This machine may pick up and throw objects which can cause serious personal injury.
BYSTA NDE RS
Keep bystanders, helpers, children and pets at least 75 feet from the machine while it is in operation.
WARNING — SLOPE OPERATION
Do not operate this machine on a slope greater than 20 degrees/35 percent.
MAX 35%
DANGER — ROTATING BLADES
To reduce the risk of injury, keep hands and feet away. Do not operate unless discharge cover or grass
catcher is in its proper place. If damaged, replace immediately.
DANGER — CHILDREN
Never carry children, even with the blade(s) shut off. They may fall off and be seriously injured or interfere
with safe machine operation.
DANGER — MOWING IN REVERSE
Always look behind and down for small children. Use slow speed.
DANGER — BACK-OVER
To avoid back-over accidents, always disengage blades before traveling in reverse.
WARNING! Your Responsibility—Restrict the use of this power machine to persons who read, understand and follow the
warnings and instructions in this manual and on the machine.
6 Section 2 — impo rtant Safe operation practiceS
SAVE THESE INSTRUCTIONS!
To check the slope, proceed as follows:
1. Remove this page and fold along the dashed line.
2. Locate a vertical object on or behind the slope (e.g. a pole, building, fence, tree, etc.)
3. Align either side of the slope gauge with the object (See Figure 1 and Figure 2 ).
4. Adjust gauge up or down until the left corner touches the slope (See Figure 1 and Figure 2).
5. If there is a gap below the gauge, the slope is too steep for safe operation (See Figure 2 above).
WARNING! Slopes are a major factor related to tip-over and roll-over accidents which can result in severe injury or death.
Do not operate machine on slopes in excess of 20 degrees (35%). All slopes require extra caution.
Always mow across the face of slopes, never up and down slopes.
(OK)
IF A SLOPE IS TOO STEEP FOR SAFE OPERATION!
USE THIS SLOPE GAUGE TO DETERMINE
20° (35%) dashed line
20° (35%) Slope
(TOO STEEP)
Figure 2Figure 1
Slope Gauge
20° (35%) Slope
7Section 2 — Safe operation practi ceS
Assembly & Set-Up
a b
(a)
(a)
(b)
(c)
(d)
2
Thank You
Thank you for purchasing this product. It was carefully engineered to
provide excellent performance when properly operated and maintained.
Please read this entire manual prior to operating the equipment. It instructs
you how to safely and easily set up, operate and maintain your machine.
Please be sure that you, and any other persons who will operate the
machine, carefully follow the recommended safety practices at all times.
Failure to do so could result in personal injury or property damage.
All information in this manual is relative to the most recent product
information available at the time. Review this manual frequently to
familiarize yourself with the machine, its features and operation. Please
be aware that this Operator’s Manual may cover a range of product
specifications for various models. Characteristics and features discussed
and/or illustrated in this manual may not be applicable to all models. We
reserve the right to change product specifications, designs and equipment
without notice and without incurring obligation.
If applicable, the power testing information used to establish the power rating
of the engine equipped on this machine can be found at ww w.opei.org or the
engine manufacturer ’s web site.
If you have any problems or questions concerning the machine, phone your
local authorized service dealer or contact us directly. We want to ensure
your complete satisfaction at all times.
Throughout this manual, all references to right and left side of the machine
are observed from the operating position.
Contents of Carton
• Trac tor (1) • Steering Wheel Assembly (1) • Operator’s Manual (1)
• Engine Operator’s Manual (1)
NOTE: This Operator’s Manual covers several models. Features may vary by model. Not all features in this manual are applicable to all models and the model
depicted may differ from yours.
NOTE: All references in this manual to the left
or right side and front or back of the tractor are
from the operating position only. Exceptions, if
any, will be specified.
Tractor Preparation
Manually Moving the Tractor
1. Engage the transmission bypass rods, one
on each side of the tractor, to move the
tractor manually without starting it. The
transmission bypass rods are located on
the rear of the tractor, just inside each rear
wheel. Engage the bypass rods by pulling
each one back (a) and hooking it into the
slot (b) to lock it into place. See Figure 2-1.
Steering Wheel Column
The steering wheel column is tilted all the way
back for shipping purposes. To tilt the column
forward, rotate the steering column adjustment
lever (a) counter-clockwise, place the column in
the desired position and then rotate the steering
column adjustment lever (a) lever clockwise to
secure the column in place. See Figure 2-2.
Steering Wheel
1. Remove the hardware for attaching
the steering wheel (a) from beneath
the steering wheel cover (b). Carefully
pry off the steering wheel cover (b)to
remove the hardware. See Figure 2-3.
Figure 2-1
2. Disengage the bypass rods by reversing
steps a & b after moving the tractor. See
Figu re 2-1.
3. Remove the deck wash system nozzle
adapter from the manual bag and store
for future use.
8
Figure 2-2
NOTE: Be sure that the steering column
adjustment lever is tight to prevent the column
from moving when operating the machine.
Figure 2-3
2. With the wheels of the machine pointing
straight forward, place the steering
wheel (a) over the steering shaft.See
Figure 2-3.
3. Place the belleville washer (c) with the
cupped side facing inward over the
steering wheel (a) and secure with the
hex lock screw (d). See Figure 2-3.
4. Place the steering wheel cover (b) over the
center of the steering wheel (a) and push
downward until it “clicks” into place.
Positioning the Roll Over Protective
a
b
c
a
b
d
(b)
(b)
(a)
(a)
(c)
System (ROPS)
The ROPS is shipped folded down for shipping
purposes. To place the ROPS into the operation
position proceed as follows.
1. Pull out on the lef t and right bracket
retainers and rotate it so that they allow
the ROPS to move freely. See Figure 2-4.
Figure 2-4
2. Rotate to ROPS forward and re-insert the
bracket retainers to secure the ROPS in
the operating position.
Lower Deck Discharge Chute Deflector
WARNING! Never operate the
mower deck without the chute
deflector installed and in the
down position.
The discharge chute deflector must be
installed before operating the mower. To install
the chute deflector, proceed as follows:
1. Remove the carriage screws (a) and
flange lock nuts (b) installed on the
mounting bracket (c) on the deck. See
Figure 2-5.
Adjusting the Seat
This tractor is equipped with an adjustable
seat, which includes a retractable seat belt
assembly and an Operator Presence Sensor
(OPS). The OPS in the form of a switch, is
integrated into the seat bottom and is
connected to the machine electrical system.
The seat can be adjusted forward and back and
the arm rest can be adjusted up and down.
To move the seat forward or back, locate the
seat adjustment rod under the seat. Push the
rod to the left and slide the seat forward or
back into the desired position and release the
rod when the seat is in the desired position.
See Figure 2-6.
Figure 2-6
To adjust the arm rest, lift the arm rest and
rotate the block adjustment into one of the
four positions (0-3, 0 being the lowest and 3
being the highest.) and lower the arm rest. See
Figur e 2-7.
Figure 2-7
The mechanical suspension mechanism (if
equipped) incorporates weight/ride adjustment
controls for operators in the 125 to 275 lb. weight
range (turn the knob on the front of the seat
clockwise to increase the weight capacit y and
counter-clockwise to decrease. See Figure 2-8.
Figure 2-8
NOTE: The seat base must be secured by the
latch, otherwise, the seat assembly could tilt
forward. The Operator Presence Sensor must
be connected to the electrical wiring harness.
Connecting the Battery Cables
CALIFORNIA PROPOSITION 65
WARNING! Battery posts,
terminals, and related
accessories contain lead and lead
compounds, chemicals known to
the State of California to cause
cancer and reproductive harm.
Wash hands after handling.
CAUTION: When attaching
battery cables, always connect
the POSITIVE (Red) wire to its
terminal first, followed by the
NEGATIVE (Black) wire.
For shipping reasons, both battery cables on your
equipment may have been left disconnected
from the terminals at the factory. To connect the
battery cables, proceed as follows:
NOTE: The positive battery terminal is marked
Pos. (+). The negative battery terminal is
marked Neg. (–).
NOTE: If the positive battery cable is
already attached, skip ahead to step 2.
3. Remove the plastic cover, if present, from
the positive battery terminal and attach
the red cable to the positive battery
terminal (+) with the bolt (a) and hex nut
(b). See Figure 2-9.
Figure 2-5
2. With the hardware removed in step 1,
install the chute deflector (d) on the
deck as shown in Figure 2-5.
Figure 2-9
9Section 2 — ASSemb ly & Set-Up
Loading...