RESV1300
ELECTRIC MULCHINATOR BLOWER / VACUUM
OPERATOR’S MANUAL
FOR QUESTIONS, CALL 1-800-345-8746 in U.S. or
1-800-265-6778 in CANADA
www.ryobi.com
IMPORTANT MANUAL DO NOT THROW AWAY
INTRODUCTION
2
TABLE OF CONTENTS
I. Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . 3-6
A. Important Safety Information . . . . . . . . . . . . . . . 3-4
B. Safety and International Symbols . . . . . . . . . . . 5-6
C. Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
II. Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . 7-9
A. Attaching and Removing the Blower/Vacuum Tube . 7
B. Attaching and Removing the Vacuum Bag . . . . . . 8
C. Installing and Adjusting the Shoulder Strap . . . . . 9
III. Operating Instructions . . . . . . . . . . . . . . . . . . . . 10-13
A. Connecting the Power Cord . . . . . . . . . . . . . . . . 10
B. Starting/Stopping the Blower/Vac . . . . . . . . . . . . 10
C. Holding the Blower/Vacuum . . . . . . . . . . . . . . . . 10
D. Operating the Unit . . . . . . . . . . . . . . . . . . . . . . . . 11
E. Air Vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
F. Operating the Unit as a Blower . . . . . . . . . . . . . . 12
G. Operating the Unit as a Vacuum . . . . . . . . . . . . . 13
H. Operating as a Vacuum . . . . . . . . . . . . . . . . . 12-13
I. Empty the Vacuum Bag . . . . . . . . . . . . . . . . . . . . 13
IV. Maintenance and Repair Instructions . . . . . . . . . . . 14
A. Servicing of Double-Insulated Blower/Vacuums . 14
B. Clearing a Blocked Impeller . . . . . . . . . . . . . . . . . 14
C. Cleaning the unit . . . . . . . . . . . . . . . . . . . . . . . . . 14
D. Cleaning the Vacuum Bag . . . . . . . . . . . . . . . . . . 14
E. Inspecting Extension Cords . . . . . . . . . . . . . . . . . 14
F. Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
V. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
VI. Accessories/Replacement Parts . . . . . . . . . . . . . . . 15
VII Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
VIII. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
CONTENTS OF CARTON
This unit includes the following:
• Blower/Vacuum Model RESV1300
• Blower/Vacuum Tube
• Shoulder Strap
• Vacuum bag
• Hardware Pack
• Operator’s Manual
• Owner’s Registration Card
Examine all parts to make certain that nothing is missing
and no breakage has occurred during shipping.
Damaged or missing parts must be replaced before
using this unit.
THANK YOU
Thank you for buying this quality product. This modern
outdoor power tool will provide many hours of useful
service. You will find it to be a great labor-saving device.
This operator’s manual provides you with easy-tounderstand operating instructions. Read the whole
manual and follow all the instructions to keep your new
outdoor power tool in top operating condition.
PRODUCT REFERENCES, ILLUSTRATIONS AND
SPECIFICATIONS
All information, illustrations and specifications in this
manual are based on the latest product information
available at the time of printing. We reserve the right to
make changes at any time without notice.
Copyright©1999 Ryobi Outdoor Products, Inc.
All Rights Reserved.
SERVICE INFORMATION
Service on this unit both within and after the warranty
period should be performed only by an authorized and
approved service dealer.
Dial:
1-800-345-8746 in the United States or
1-800-265-6778 in Canada
to obtain the listing of the authorized service dealer
nearest you.
DO NOT RETURN THE UNIT TO THE RETAILER.
NOTE: PROOF OF PURCHASE WILL BE REQUIRED
FOR WARRANTY SERVICE.
Make sure this manual is carefully read and understood
before starting or operating this equipment.
THIS PRODUCT IS COVERED BY ONE OR MORE
US PATENTS, OTHER PATENTS PENDING.
WARNING: The operation of any blower/vacuum can result in foreign objects being thrown in
the eyes. This can lead to severe eye damage. Before commencing power tool operation, always wear
safety glasses or goggles that are marked as meeting ANSI Z87.1-1989 standards, and a full face shield
when needed.
The purpose of safety symbols is to attract your
attention to possible dangers. The safety symbols,
and their explanations, deserve your careful attention
and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or
warnings they give are not substitutes for proper
accident prevention measures.
SYMBOL MEANING
SAFETY ALERT SYMBOL:
Indicates danger, warning, or caution.
Attention is required in order to avoid serious
personal injury. May be used in conjunction
with other symbols or pictographs.
NOTE: Advises you of information or instructions vital to
the operation or maintenance of the equipment.
DANGER:
Failure to obey a safety warning will result in
serious injury to yourself or to others. Always
follow the safety precautions to reduce the
risk of fire, electric shock, and personal injury.
WARNING:
Failure to obey a safety warning can result in
injury to yourself and others. Always follow
the safety precautions to reduce the risk of
fire, electric shock, and personal injury.
CAUTION:
Failure to obey a safety warning may result
in property damage or personal injury to
yourself or to others. Always follow the
safety precautions to reduce the risk of fire,
electric shock, and personal injury.
RULES FOR SAFE OPERATION
3
• IMPORTANT SAFETY INSTRUCTIONS •
WARNING:
When using this electric Blower/Vacuum,
basic safety precautions should always be
followed to reduce the risk of fire, electric
shock, and personal injury. Carefully read
and understand the entire Operator's
Manual before using your Blower/Vacuum.
Pay close attention to the Operating
Instructions and Safety Warnings.
READ ALL INSTRUCTIONS BEFORE USING
WARNING:
To reduce the risk of fire, electric shock, or injury:
• Do not leave the Blower/Vacuum when plugged in.
Unplug from outlet when not in use, changing
attachments, and before servicing.
• Do not use on wet surfaces. Do not expose to rain.
Store indoors.
• Use the right tool. Use this unit only as described in
this manual. Do not use for any job except that for
which it is intended. Use only the manufacturer’s
recommended attachments.
• Do not abuse the power cord. Do not pull or carry the
unit by the cord, use cord as a handle, close a door on
cord, or pull the cord around sharp edges or corners.
Keep the cord away from heated surfaces, oil and
sharp edges.
• Turn off all controls before unplugging.
• Do not unplug by pulling on the cord. To unplug, grasp
the plug, not the cord.
• Do not handle the plug or Blower/Vacuum with wet
hands or standing on any wet surfaces.
• Do not put any object into openings. Do not use with
any opening blocked; keep free of dirt, debris and
anything that may reduce the air flow.
• Keep hair, loose clothing, fingers, and all parts of body
away from openings and moving parts.
• Use extra care when cleaning on stairs.
• Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
• Do not use to pick up flammable or combustible
liquids, such as gasoline, or use in areas where they
may be present.
• This Blower/Vacuum is provided with
double-insulation. Use only identical replacement
parts. See instructions for Servicing of
Double-Insulated Blower/Vacuums.
• Do not use with damaged cord or plug. If
Blower/Vacuum is not working as it should, has been
dropped, damaged, left outdoors, or dropped in water,
return it to an authorized service center.
• Inspect all extension cords and the unit power
connection periodically. Look closely for deterioration,
cuts or cracks in the insulation. Also inspect the
connections for damage. Replace the cords if any
defects or damage appear.
RULES FOR SAFE OPERATION
4
• A nameplate on your unit indicates what voltage it
uses. Never connect the unit to an AC voltage that
differs from this voltage.
BEFORE OPERATING
• Read the instructions carefully. Be familiar with the
controls and proper use of the unit.
• Use only extension cords approved for outdoor use,
such as an extension cord of cord type SW-A, SOWA, STW-A, STOW-A, SJW-A, SJOW-A, SJTW-W or
SJTOW-A. A 2-wire extension cord (an extension cord
without a ground) may be used because the tool is
double insulated. However, a 3-wire extension cord
(an extension cord with a ground) that uses a NEMA
type connector (parallel blade, U ground) may also be
used. Extension cords are available from your local
retailer. Use only round-jacketed extension cords
approved for outdoor use.
• To reduce the risk of electrical shock, this unit has a
polarized plug (one blade is wider than the other) and
will require the use of a polarized extension cord. This
unit plug will fit into a polarized extension cord only
one way. If the plug does not fit fully into the extension
cord, reverse the plug. If the plug still does not fit,
obtain a correct polarized extension cord. A polarized
extension cord will require the use of a polarized wall
outlet. This plug will fit into a polarized wall outlet only
one way. If the plug does not fit fully into the wall
outlet, reverse the plug. If the plug still does not fit,
contact a qualified electrician to install the proper wall
outlet. Do not change the unit plug, extension cord
receptacle, or extension cord plug in any way.
• Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s) to be
used for this unit. Receptacles are available having
built-in GFCI protection and may be used for this
measure of safety.
• CORD SETS: Make sure your cord set is in good
condition. When using a cord set, be sure to use a
cord that is heavy enough to carry the current that
your unit will draw. An undersized cord set will cause a
drop in line voltage resulting in loss of power and
overheating. The table shows the correct size to use
depending on the cord length and nameplate
amperage rating. If in doubt, use the next heavier size
line gauge. The smaller the gauge number, the heavier
the cord. To reduce the possibility of disconnection of
the unit from the cord set during operation, see
Fig. 11, page 10.
• Children and teens under the age of 15 must not use
the unit, except for teens guided by an adult.
• Before each use, thoroughly inspect your
Blower/Vacuum for loose or damaged parts. Do not
use until adjustments or repairs are made.
• All guards and safety attachments must be installed
properly before operating the unit.
• Use the unit only in daylight or good artificial light.
• Keep all bystanders, especially children and pets, at
least 50 feet (15 m) away from the unit while operating.
• Inspect the area before starting the Blower/ Vacuum.
Remove all debris and hard or sharp objects such as
glass, wire, etc.
FOR SAFE OPERATION
• Avoid accidental starting. Do not carry plugged-in unit
with your finger on the switch. Be sure switch is off
when plugging in.
• Always remain alert. Use common sense. To prevent
injury to yourself and others, do not operate this unit if
you are fatigued.
• Do not operate the unit while under the influence of
drugs, alcohol or medication.
• Wear safety glasses or goggles that are marked as
meeting ANSI Z87.1-1989 standards, and ear/hearing
protection when operating this unit. Wear a face or
dust mask if the operation is dusty. Long sleeve shirts
are recommended.
• Do not overreach or use the unit from unstable
surfaces such as ladders, trees, steep slopes,
rooftops, etc. Keep proper footing and balance at all
times.
• Wear heavy long pants, boots and gloves. Do not wear
loose clothing, jewelry, short pants or sandals. Do not
operate the unit barefoot. Secure hair above shoulder
level.
• Do not point the Blower/Vacuum in anyone’s direction
or in the direction of windows.
• Do not force unit. It will do the job better and with less
likelihood of injury at a rate for which it was designed.
• Avoid situations that could catch the vacuum bag on
fire. Do not operate near an open flame. Do not
vacuum warm ash from fireplaces, barbecue pits,
brush piles, etc. Do not vacuum discarded cigars or
cigarettes unless the cinders are completely cool.
• Never use the Blower/Vacuum without the
blower/vacuum tube and vacuum bag attached.
• As a vacuum, the unit is designed to pick up dry
material such as leaves, grass, small twigs and bits of
paper. Do not attempt to vacuum wet debris and/or
standing water as this may result in damage to the
Blower/ Vacuum and possible electric shock. To avoid
damage to the impeller, do not vacuum metal, broken
glass, etc.
MINIMUM WIRE SIZE FOR EXTENSION CORDS
FOR 120 VOLT APPLIANCES
Cord length (ft) 25 50 100 150
Amperage Rating Wire size (AWG)
6 to 10 amps 18 16 14 12
10 to 12 amps 16 16 14 12
12 to 16 amps 14 12
NOT
RECOMMENDED
SAFETY AND INTERNATIONAL SYMBOLS
This operator's manual describes safety and international symbols and pictographs that may appear on this product.
Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.
SYMBOL MEANING
• SAFETY ALERT SYMBOL
Indicates danger, warning, or caution. May be used in conjunction with other
symbols or pictographs.
• WARNING - READ OPERATOR'S MANUAL
Read the operator's manual before starting or operating this unit. Failure to follow operating
instructions and safety precautions in the operator's manual can result in serious injury to the
operator and/or bystanders.
• FOR SERVICE INFORMATION, CALL:
USA: 1-800-345-8746
CANADA: 1-800-265-6778
• WEAR EYE AND HEARING PROTECTION
WARNING: Wear safety glasses or goggles that are marked as meeting ANSI Z87.1-1989
standards, and ear/hearing protection when operating this unit.
• DO NOT USE IN THE RAIN
WARNING: Avoid dangerous environments. Never operate your unit in the rain, or in
damp or wet conditions. Moisture is a shock hazard.
• BLOWERS AND BLOWER/VACUUMS – ROTATING IMPELLER BLADES CAN
CAUSE SEVERE INJURY
WARNING: Stop the engine and allow the impeller to stop before installing or changing
tubes or bag.
RULES FOR SAFE OPERATION
5
• Unplug the Blower/Vacuum before attempting to
install or remove the blower/vacuum tube or
vacuum bag. The unit must be unplugged, and the
impeller blades stopped to avoid contact with the
rotating blades.
OTHER SAFETY WARNINGS
• Store unit indoors. Store unit indoors in a dry place, up
high or locked-up, out of the reach of children.
• Use only genuine replacement parts approved by
Ryobi when servicing this unit. See servicing of
double-insulated units in the maintenance and repair
section, page 14. The use of non-standard parts, or
other accessories or attachments not designed for this
unit, could result in serious injury to the user or
damage to the Blower/Vacuum and void your
warranty.
• Maintain this Blower/Vacuum with care. Keep the unit
clean and serviced for the best and safest
performance. Follow the maintenance instructions.
Always use a clean cloth when cleaning. Never use
strong detergents, gasoline, petroleum-based
products, or any strong solvents to clean the unit.
• Keep your unit in good working condition. Follow
instructions for servicing and changing accessories.
Inspect unit periodically, and if damaged, have it
repaired by an authorized service facility. Inspect
extension cords periodically and replace if damaged.
Keep handles dry, clean, and free from oil and grease.
• Keep these instructions. Refer to them frequently and
use them to instruct other users. If you loan someone
this unit, also loan them these instructions.
SAVE THESE INSTRUCTIONS
RULES FOR SAFE OPERATION
6
APPLICATION
This unit is intended for household purpose only.
Use for cleaning of yards, garages, shops, porches,
patios, etc..
Shoulder Strap
Blower/Vacuum Tube
Vacuum Bag
Blower/Vacuum Mode
Change-Over Lever
Blower/Vacuum Inlet
Blower Outlet
Vacuum Bag Hook
Power/Speed Switch
Motor Air Vents
Vacuum Bag Zipper
Latch Support
KNOW YOUR UNIT
SYMBOL MEANING
• KEEP BYSTANDERS AWAY
WARNING: Keep all bystanders, especially children and pets, at least 50 feet (15 m) from
the operating area.
• BLOWER/VACUUM MODE CHANGE-OVER LEVER
A - Vacuum mode
B - Blower mode
• THROWN OBJECTS
WARNING: Objects can be thrown from blower. Keep away from blower outlet.
ASSEMBLY INSTRUCTIONS
7
Screw
and Nut
Screw and Nut
Self Tapping
Screw
ATTACHING AND REMOVING THE
BLOWER/VACUUM TUBE
WARNING: To avoid serious personal injury,
the blower/vacuum tube and vacuum bag
must be used when operating this unit
Attaching
NOTE: The Blower/Vacuum Tube comes unassembled
on this unit. Installation is required to provide
safe and easy use for the operator.
WARNING: To avoid serious personal injury,
be sure the unit is in the off position and
unplugged before assembling tubes.
1. Remove the screws and nuts provided from the
hardware pack.
2. Insert the blower/vacuum tube all the way into the
opening on the motor housing until the holes in the
tabs on the blower/vacuum tube align with the screw
holes in the housing (Fig. 1).
3. Insert the 2 (two) 8-32 x 3/4” slotted T20 Torx
screws into the right side of the motor housing
and the 2 (two) nuts into the left side of the motor
housing (Fig. 2).
Fig. 1
4. Tighten the screws firmly. Do not over-tighten.
5. Install the 2 (two) remaining self-tapping 8-16 x 3/4”
slotted T20 Torx screws into the holes on either side
of the housing (Fig. 2). Tighten until snug, do not to
over-tighten.
Removing
NOTE: It may be necessary to remove the
Blower/Vacuum Tube to clear a blocked tube
or impeller.
WARNING: To avoid serious personal injury,
be sure the unit is in the off position and
unplugged before removing tubes.
1. Remove the 2 (two) self-tapping screws from either
side of the housing.
2. Remove the 2 (two) screws and nuts holding the
blower/vacuum tube on the housing (Fig. 1).
NOTE: Keep the hardware in a safe place for future use.
Fig. 2
3. Remove the blower/vacuum tube from the motor
housing.
4. Replace Blower/Vacuum Tube before use.
Screw
Nut
Blower/Vacuum
Tube
Motor Housing
Self-Tapping Screw
Removing
NOTE: It is necessary to remove the Vacuum Bag to
empty and clean the bag.
1. Press the latching tabs on both sides of the vacuum
bag tube and pull the vacuum bag from the unit
(Fig. 5).
2. Detach the vacuum bag from the vacuum bag hook
(Fig. 3).
Fig. 5
ASSEMBLY INSTRUCTIONS
8
Vacuum Bag
Vacuum Bag Hook
Debris Exhaust Tube
Vacuum Bag Tube
Zipper
ATTACHING AND REMOVING THE VACUUM
BAG
Attaching
NOTE: The Vacuum Bag comes unassembled on this
unit. Installation is required to provide safe and
easy use for the operator.
1. Attach the vacuum bag to the vacuum bag hook on
the blower/vacuum tube (Fig. 3).
Fig. 4
Fig. 3
2. Slide the vacuum bag tube over the debris exhaust
tube on the housing. Push the tube until the latching
tabs on both sides click into place, securing the bag
on the unit (Fig. 4).
Latching tabs
Latching tabs
3. Replace Bag before using unit.
ASSEMBLY INSTRUCTIONS
9
4. Attach the metal clip of the shoulder strap to the
latch support on top of the handle (Fig. 8).
Fig. 9
Fig. 7
Fig. 10
Fig. 8
5. Place the strap over your head and onto your
shoulder (Fig. 9).
6. While standing in the operating position (Fig. 9)
adjust length to fit the operator’s size.
• Lengthen the strap by pulling down on the strap and
moving the buckle up (Fig. 10).
• Shorten the strap by pulling the strap back through
the buckle while moving the buckle down (Fig. 10).
Latch Support
Clip
Latch
INSTALLING AND ADJUSTING THE SHOULDER
STRAP
1. Push the strap through the center of the buckle.
2. Pull the strap over the cross bar and down through
the slot in the buckle (Fig. 6).
Fig. 6
3. Fully extend the strap (Fig. 7).
WARNING: To reduce the risk of electrical
shock, this unit has a polarized plug (one
blade is wider than the other) and will require
the use of a polarized extension cord. This
unit plug will fit into a polarized extension
cord only one way. If the plug does not fit
fully into the extension cord, reverse the plug.
If the plug still does not fit, obtain a correct
polarized extension cord. A polarized
extension cord will require the use of a
polarized wall outlet. This plug will fit into a
polarized wall outlet only one way. If the
plug does not fit fully into the wall outlet,
reverse the plug. If the plug still does not fit,
contact a qualified electrician to install the
proper wall outlet. Do not change the unit
plug, extension cord receptacle, or extension
cord plug in any way.
1. Secure the extension cord to motor housing as
shown (Fig. 11) to the prevent accidental removal of
the electrical cord.
Cord length (ft) 25 50 100 150
Amperage Rating Wire size (AWG)
10 to 12 amps 16 16 14 12
OPERATING INSTRUCTIONS
10
CONNECTING THE POWER CORD
Use a minimum 25 foot (7.6 m.) long, 16AWG, outdoor
electrical cord when using this unit. Other sizes include:
OFF
LOW
HIGH
Fig. 11
Fig. 13
STARTING AND STOPPING THE BLOWER/VAC
This unit is equipped with a three way OFF/LOW/HIGH
switch (Fig. 13).
• Slide the switch all the way down for OFF.
• Slide the switch up to the first click for LOW.
• Slide the switch up to the second click for
HIGH.
Fig. 12
2. Plug the female end of the electrical cord into the
receptacle at the back of the unit (Fig. 12).
Receptacle
OPERATING INSTRUCTIONS
11
OPERATING TIPS
• Be sure the vacuum bag is zipped closed before
operating the unit.
• Assure the unit is not directed at loose debris or
persons before starting unit.
• Assure the unit is in good working condition with
tubes and guards in place and secure.
• Always hold the unit with both hands when
operating. Keep a firm grip on both the front and rear
handle or grips.
• To reduce the risk of hearing loss associated with
sound level(s) hearing protection is advisable.
• Operate power equipment only at reasonable hours,
not early in the morning or late at night when people
might be disturbed. Comply with time listed in local
ordinance. Usual recommendations are 9:00 am to
5:00 pm, Monday through Saturday.
• To reduce noise levels, limit the pieces of equipment
used at any one time.
• To reduce noise levels, operate power blowers at the
lowest possible speed to do the job.
• Use rakes and brooms to loosen debris before
blowing.
• Conserve water by using power blowers instead of
hoses for many lawn and garden applications, such
as gutters, screens, patios, grills, porches, and
gardens.
• Watch out for children, pets, open windows, or
freshly washed cars.
• After using blowers and other equipment, CLEAN
UP! Dispose of debris in trash receptacles.
Air Vents
AIR VENTS
Never cover air vents. Keep them free from obstructions
and debris. They must always remain clear for proper
motor cooling (Fig. 15).
WARNING: To avoid serious personal injury,
do not wear loose fitting clothing or articles
such as scarves, strings, chains, ties, etc.
that could get drawn into the air vents. To
make sure long hair does not get drawn into
the air vents secure hair above shoulder
level.
Fig. 15
HOLDING THE BLOWER/VACUUM
Before operating the unit, stand in the operating position
(Fig. 14). Check for the following:
• The operator is wearing proper clothing, such as
boots, safety glasses or goggles, ear/hearing
protection, gloves, long pants and long sleeve shirt.
WARNING: To avoid serious personal injury,
wear goggles or safety glasses at all times
when operating this unit. Wear a face mask
or dust mask in dusty locations.
• A dust mask or face mask should be worn in dusty
conditions.
• The unit is in good working condition.
• The tubes and guards are in place and secure.
• The vacuum bag is installed and zipped closed.
WARNING: To prevent serious personal injury
to yourself or others, or damage to the unit,
make sure the vacuum bag, all tubes and
guards are in place before operating your unit.
Fig. 14
OPERATING INSTRUCTIONS
12
Change-over lever
Use the blower for walls, overhangs and screens
(Fig. 19).
Use the blower around buildings and for other normal
cleaning (Fig. 18).
OPERATING AS A BLOWER
Set the blower/vacuum mode change-over lever to the
up position (Blower Mode) (Fig. 16).
NOTE: Never use the unit with the lever in the halfway
position.
Fig. 16
3. Place the shoulder strap over your head and onto
your shoulder and adjust properly, see Installing
and Adjusting the Shoulder Strap Pg. 9.
Hold the blower as shown in Figs. 17, 18, and 19. Sweep
from side to side with the nozzle several inches above
the ground or floor. Slowly advance, keeping the
accumulated pile of debris in front of you.
Most dry blowing operations are better suited to low
speed than high, while high speed is better for moving
heavier items like large debris or gravel.
Use the blower for trees, shrubs, flower beds and
hard to clean areas (Fig. 17).
Blower
Vacuum
Fig. 17
Fig. 18
Fig. 19
OPERATING INSTRUCTIONS
13
OPERATING AS A VACUUM
Set the blower/vacuum mode change-over lever to the
down position (Vacuum Mode) (Fig. 20).
NOTE: Never use the unit with the lever in the halfway
position.
Place the shoulder strap over your head and onto your
shoulder and adjust properly, see Installing and
Adjusting the Shoulder Strap Pg. 9.
Hold the vacuum, tilting the blower/vacuum tube slightly,
and use a sweeping action to collect light debris
(Fig. 14, Pg. 11). Small leaves and twigs will flow into the
vacuum bag and be mulched as they pass through the
fan housing, allowing the vacuum bag to hold more
debris.
WARNING: As a vacuum, the unit is
designed to pick up dry material such as
leaves, grass, small twigs and bits of paper.
To avoid serious personal injury, do not
attempt to vacuum wet debris and/or
standing water as this may result in damage
to the Blower/ Vacuum. To avoid severe
damage to the impeller, do not vacuum
metal, broken glass, etc.
WARNING: Avoid situations that could catch
the vacuum bag on fire. Do not operate near
an open flame. Do not vacuum warm ash
from fireplaces, barbecue pits, brush piles,
etc. Do not vacuum discarded cigars or
cigarettes unless the cinders are completely
cool.
When the bag is full, suction will noticeably decrease.
Turn off the unit before removing the bag. Unzip the bag
and empty the contents before continuing.
Empty the Vacuum Bag
WARNING: To avoid serious personal injury,
be sure the unit is in the off position and
unplugged before unzipping or removing the
vacuum bag.
NOTE: Empty the bag after each use to avoid
deterioration and obstructing air flow, which will
reduce the performance of the vacuum.
WARNING: Wear eye protection and a dust
mask when emptying the vacuum bag.
1. While pressing the latching tabs on both sides of the
vacuum bag tube, pull the vacuum bag off the unit
(Fig. 21).
2. Detach the vacuum bag from the vacuum bag hook.
4. Unzip the bag and empty the contents into a
garbage bag or container.
5. Turn the bag inside out after initial emptying and
vigorously shake out dust and debris.
6. Zip the bag closed and reinstall vacuum bag.
Fig. 20
Fig. 21
Latching tabs
Change-over lever
Blower
Vacuum
MAINTENANCE AND REPAIR INSTRUCTIONS
14
WARNING: To avoid serious
personal injury, be sure the unit is off and
unplugged before cleaning or performing any
maintenance on it.
SERVICING OF DOUBLE INSULATED UNITS
This unit is double-insulated. In a double-insulated unit,
two systems of insulation are provided instead of
grounding. No means of grounding are provided on a
double-insulated unit, nor should a means for grounding
be added to this unit.
Servicing a double-insulated unit requires extreme care
and knowledge of the system, and should be done only
by qualified service personnel. Replacement parts for a
double-insulated unit must be identical to the parts they
replace. Refer any repair to an authorized service dealer.
A double-insulated unit is marked with the words
“DOUBLE INSULATION” or “DOUBLE INSULATED.”
CLEARING A BLOCKED TUBE/IMPELLER
1. Push the switch to the OFF position and disconnect
the Blower/Vacuum from the power source. Wait for
the impeller to stop rotating.
2. Remove the blower/vacuum tube. See Attaching
and removing the Blower/Vacuum Tube Pg. 7. The
vacuum bag can also be removed. See Attaching
and removing the Vacuum Bag Pg. 8.
3. Carefully remove material blocking the impeller or
tube. Inspect the blades to assure no damage has
occurred. Rotate the blades by hand to assure the
blockage is completely cleared.
4. Reinstall the vacuum bag and blower/vacuum tube.
5. Reconnect to power source and resume use.
CLEANING THE UNIT
1. Push the switch to the OFF position and disconnect
the Blower/Vacuum from the power source.
2. Use a small brush or the air discharge of a vacuum
cleaner brush to keep the air vents free of
obstructions.
3. Do not use strong detergents on the plastic housing
or components. These can be damaged by certain
household cleaners that contain aromatic oils such
as pine and lemon, and by solvents such as
kerosene or acetone. Moisture can also cause a
shock hazard. Wipe off any moisture with a soft
cloth.
CLEANING THE VACUUM BAG
1. Empty the bag after each use to avoid deterioration
and obstructing air flow, which will reduce the
performance of the vacuum.
2. Wearing eye protection and a dust mask, clean the
bag as needed. Turn the bag inside out after initial
emptying and vigorously shake out dust and debris.
3. Wash the bag once a year or more often if needed:
a. Remove the vacuum bag.
b. Turn bag inside out.
c. Hang up.
d. Hose down thoroughly, washing from the
outside to the inside.
e. Hang to dry.
f. Turn bag right-side out and reinstall.
INSPECT EXTENSION CORDS
Inspect all extension cords periodically. Look closely for
deterioration, cuts or cracks in the insulation. Inspect the
connectors for damage. Replace cords if defective or
damaged.
STORAGE
• Store the unit indoors, away from moisture and
harmful substances such as fertilizers and solvents.
• Store in a dry and high or locked-up place, out of the
reach of children.
• Store the unit locked up to prevent unauthorized use
or damage.
• Store the unit in a dry, well ventilated area.
• Store the unit out of the reach of children.
15
Motor Amperage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Amps
Blower Air Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . up to 160 mph (257.5 kmh)
Vacuum Air Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . up to 424 cfm (12 cmm)
Mulching Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . up to 10:1
Operating Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 lb (4.5 kg)
Vacuum Bag Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.75 bushels (26.4 L)
Vacuum Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181836
Blower/Vacuum Tube Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181999
Shoulder Strap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682075
SPECIFICATIONS
ACCESSORIES/REPLACEMENT PARTS
CAUSE ACTION
Bag Full Empty Bag. See Empty the Vacuum Bag, Pg. 13
Blocked Tube Clear Blockage. See Clearing a Blocked
tube/Impeller, Pg 14.
Blocked Impeller Clear Blockage. See Clearing a Blocked
tube/Impeller, Pg 14.
Damaged Impeller Take unit to an authorized service dealer
Dirty Bag Clean Bag
Torn Bag Replace Bag
Bag Unzipped Zip Up Bag
Unplugged Plug into Outlet or Extension Cord
UNIT WILL NOT BLOW OR VACUUM
TROUBLESHOOTING
ALL IMPLIED WARRANTIES ARE LIMITED IN
DURATION TO THE TWO (2) YEAR WARRANTY
PERIOD OR NINETY (90) DAYS FOR PRODUCTS
USED FOR ANY COMMERCIAL PURPOSE.
ACCORDINGLY, ANY SUCH IMPLIED WARRANTIES
INCLUDING MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR OTHERWISE, ARE
DISCLAIMED IN THEIR ENTIRETY AFTER THE
EXPIRATION OF THE APPROPRIATE TWO-YEAR
OR NINETY DAY WARRANTY PERIOD. RYOBI’S
OBLIGATION UNDER THIS WARRANTY, IS STRICTLY
AND EXCLUSIVELY LIMITED TO THE REPAIR OR
REPLACEMENT OF DEFECTIVE PARTS, AND ROP
DOES NOT ASSUME OR AUTHORIZE ANYONE TO
ASSUME FOR THEM ANY OTHER OBLIGATION.
SOME STATES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO
THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
RYOBI ASSUMES NO RESPONSIBILITY FOR
INCIDENTAL, CONSEQUENTIAL OR OTHER
DAMAGES INCLUDING, BUT NOT LIMITED TO
EXPENSE OF RETURNING THE RYOBI PRODUCT
TO AN AUTHORIZED SERVICE DEALER AND
EXPENSE OF DELIVERING IT BACK TO THE
OWNER, MECHANIC’S TRAVEL TIME, TELEPHONE
OR TELEGRAM CHARGES, RENTAL OF A LIKE
PRODUCT DURING THE TIME WARRANTY SERVICE
IS BEING PERFORMED, TRAVEL, LOSS OR DAMAGE
TO PERSONAL PROPERTY, LOSS OF REVENUE,
LOSS OF USE OF THE PRODUCT, LOSS OF TIME,
OR INCONVENIENCE. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU.
This warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state.
This warranty applies to all RYOBI Products
manufactured by RYOBI and sold in the United States
and Canada.
To locate your nearest service dealer dial
1-800-345-8746 in the United States or
1-800-265-6778 in Canada.
RYOBI OUTDOOR PRODUCTS
550 N. 54th Street
Chandler, AZ 85226 U.S.A.
RYOBI CANADA INC.
275 Industrial Rd
Cambridge, Ontario N1R 6K2 CANADA
RYOBI OUTDOOR PRODUCTS warrants each new
RYOBI Product for two (2) years according to the
following terms.
This warranty extends to the original retail purchaser
only and commences on the date of original retail
purchase.
Any part of the RYOBI Product manufactured or
supplied by RYOBI and found in the reasonable
judgement of RYOBI to be defective in material or
workmanship will be repaired or replaced by an
authorized RYOBI service dealer without charge for
parts and labor.
The RYOBI Product including any defective part must
be returned to an authorized service dealer within the
warranty period. The expense of delivering the RYOBI
Product to the dealer for warranty work and the
expense of returning it back to the owner after repair
or replacement will be paid for by the owner. RYOBI’s
responsibility in respect to claims is limited to making
the required repairs or replacements and no claim of
breach of warranty shall be cause for cancellation or
rescission of the contract of sale of any RYOBI
Product. Proof of purchase will be required by the
dealer to substantiate any warranty claim. All warranty
work must be performed by an authorized RYOBI
service dealer.
This warranty is limited to ninety (90) days from the
date of original retail purchase for any RYOBI Product
that is used for rental or commercial purposes, or any
other income-producing purpose.
This warranty does not cover any RYOBI Product that
has been subject to misuse, neglect, negligence, or
accident, or that has been operated in any way
contrary to the operating instructions as specified in
the RYOBI Operator’s Manual. This warranty does not
apply to any damage to the RYOBI Product that is the
result of improper maintenance or to any RYOBI
Product that has been altered or modified so as to
adversely affect the product's operation, performance
or durability or that has been altered or modified so as
to change its intended use. The warranty does not
extend to repairs made necessary by normal wear or
by the use of parts or accessories which are either
incompatible with the RYOBI Product or adversely
affect its operation, performance or durability.
In addition, this warranty does not cover:
RYOBI reserves the right to change or improve the
design of any RYOBI Product without assuming
any obligation to modify any product previously
manufactured.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
FOR QUESTIONS CALL 1-800-345-8746 IN U.S.
OR 1-800-265-6778 IN CANADA
OPERATOR’S MANUAL PART NO. 182272 REV. A (51480)
PRINTED IN U.S.A. 5/99
LIMITED TWO-YEAR WARRANTY
Loading...