Cub Cadet LTX 1051, LTX 1050 Operator's Manual

Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty

ATOR S

ANUAL

Hydrostatic Lawn Tractor m LTX 1050

CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHiO 44136-0019

PrintedIn USA FormNo.769-04350

(November3,2008)

ToTheOwner

ThankYou

1

Thank you for purchasing a Lawn Tractor manufactured by Cub
Cadet LLC. It was carefully engineered to provide excellent

performance when properly operated and maintained.
Please read this entire manual prior to operating the equipment.

It instructs you how to safely and easily set up, operate and
maintain your machine. Please be sure that you, and any other
persons who will operate the machine, carefully follow the
recommended safety practices at all times. Failure to do so could

result in personal injury or property damage.
All information in this manual is relative to the most recent

product information available at the time of printing. Review
this manual frequently to familiarize yourself with the machine,

its features and operation. Please be aware that this Operator's
Manual may cover a range of product specifications for various

models. Characteristics and features discussed and/or illustrated
in this manual may not be applicable to all models. Cub Cadet

LLC reserves the right to change product specifications, designs
and equipment without notice and without incurring obligation.

Table of Contents

Safe Operation Practices ........................................ 3

Assembly & Set-Up .................................................. 9

Controls & Features ................................................ 12

Operation ................................................................ 13

Maintenance &Adjustment. ................................. 19

If you have any problems or questions concerning the machine,
phone your local Cub Cadet dealer or contact us directly. Cub

Cadet's Customer Support telephone numbers, website address
and mailing address can be found on this page. We want to
ensure your complete satisfaction at all times.

Throughout this manual, all references to right and left side of the
machine are observed from the operating position

The engine manufacturer is responsible for all engine-related
issues with regards to performance, power-rating, specifications,
warranty and service. Please refer to the engine manufacturer's
Owner's/Operator's Manual, packed separately with your

machine, for more information.

Service .................................................................... 24

Troubleshooting .................................................... 29

Replacement Parts ................................................ 30

Attachments & Accessories .................................. 32

Warranty ................................................................ 36

RecordProductinformation

Before setting up and operating your new equipment, please
locate the model plate on the equipment and record the
information in the provided area to the right. You can locate the
model plate by looking beneath the seat. This information will
be necessary, should you seek technical support via our web site,

Customer Support Department, or with a local authorized service
dealer.

MODEL NUMBER

DDDDDDDDDDD

SERIAL NUMBER

DNDNDNDNDND

CustomerSupport

If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of
this machine, you can seek help from the experts. Choose from the options below:

0 Visit us on the web at www.cubcadetcom
0 Call a Customer Support Representative at (800) 965-4CUB

0 Locate your nearest Cub Cadet Dealer at [phone]
0 Write us at Cub Cadet LLC• RO. Box 361131 • Cleveland, OH • 44136-0019

ImportantSafeOperationPractices

WARNING! This symbol points out important safety instructions which, if not followed,

could endanger the personal safety and/or property of yourself and others. Read and follow
all instructions in this manual before attempting to operate this machine. Failure to comply

with these instructions may result in personal injury.
When you see this symbol. HEED ITS WARNING!

CALIFORNIA PROPOSITION 65

WARNING! Engine Exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to State of California to cause cancer and birth defects
or other reproductive harm.

WARNING! Battery posts, terminals, and related accessories contain lead and lead

,A

compounds, chemicals known to the State of California to cause cancer and reproductive
harm. Wash hands after handling

DANGER! This machine was built to be operated according to the safe operation practices in

this manual. As with any type of power equipment, carelessness or error on the part of the

operator can result in serious injury. This machine is capable of amputating hands and feet
and throwing objects. Failure to observe the following safety instructions could result in

serious injury or death.

2

GeneralOperation

1. Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.

2. Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them

quickly.

3. Never allow children under 14 years of age to operate this
machine. Children 14 and over should read and understand

the instructions and safe operation practices in this manual
and on the machine and should be trained and supervised

by an adult.

4. Never allow adults to operate this machine without proper
instruction.

5_

To help avoid blade contact or a thrown object injury,
keep bystanders, helpers, children and pets at least 75 feet

from the machine while it is in operation. Stop machine if
anyone enters the area.

6. Thoroughly inspect the area where the equipment is to be
used. Remove all stones, sticks, wire, bones, toys, and other
foreign objects which could be picked up and thrown by
the blade(s). Thrown objects can cause serious personal
injury.

7. Plan your mowing pattern to avoid discharge of material
toward roads, sidewalks, bystanders and the like. Also,
avoid discharging material against a wall or obstruction
which may cause discharged material to ricochet back

toward the operator.

8. Always wear safety glasses or safety goggles during
operation and while performing an adjustment or repair
to protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.

9. Wear sturdy, rough-soled work shoes and close-fitting
slacks and shirts. Loose fitting clothes and jewelry can be

caught in movable parts. Never operate this machine in
bare feet or sandals.

10. Be aware of the mower and attachment discharge direction
and do not point it at anyone. Do not operate the mower
without the discharge cover or entire grass catcher in its
proper place.

11. Do not put hands or feet near rotating parts or under the
cutting deck. Contact with the blade(s) can amputate
hands and feet.

12. Amissingordamageddischargecovercancauseblade
contactorthrownobjectinjuries.

13. Stoptheblade(s)whencrossinggraveldrives,walks,or
roadsandwhilenotcuttinggrass.

14. Watchfortrafficwhenoperatingnearorcrossing
roadways.Thismachineisnotintendedforuseonany
publicroadway.

15. Donotoperatethemachinewhileundertheinfluenceof
alcoholordrugs.

16. Mowonlyindaylightorgoodartificiallight.

17. Nevercarrypassengers.

18. Disengageblade(s)beforeshiftingintoreverse.Backup
slowly.Alwayslookdownandbehindbeforeandwhile

backingtoavoidaback-overaccident.

19. Slowdownbeforeturning.Operatethemachinesmoothly.
Avoiderraticoperationandexcessivespeed.

20. Disengageblade(s),setparkingbrake,stopengineandwait
untiltheblade(s)cometoacompletestopbeforeremoving

grasscatcher,emptyinggrass,uncloggingchute,removing
anygrassordebris,ormakinganyadjustments.

21. Neverleavearunningmachineunattended.Alwaysturn
offblade(s),placetransmissioninneutral,setparking
brake,stopengineandremovekeybeforedismounting.

22. Useextracarewhenloadingorunloadingthemachineinto
atrailerortruck.Thismachineshouldnotbedrivenupor
downramp(s),becausethemachinecouldtipover,causing
seriouspersonalinjury.Themachinemustbepushed
manuallyonramp(s)toloadorunloadproperly.

23.

Mufflerandenginebecomehotandcancauseaburn.Do
nottouch.

24.

Checkoverheadclearancescarefullybeforedrivingunder
lowhangingtreebranches,wires,dooropeningsetc.,
wheretheoperatormaybestruckorpulledfromthe
machine,whichcouldresultinseriousinjury.

25.

Disengageallattachmentclutches,depressthebrake
pedalcompletelyandshiftintoneutralbeforeattempting
tostartengine.

26.

Your machine isdesigned to cut normal residential grass of
a height no more than 10". Do not attempt to mow through
unusually tall, dry grass (e.g., pasture) or piles of dry leaves.
Dry grass or leaves may contact the engine exhaust and/
or build up on the mower deck presenting a potential fire

hazard.

27. Use only accessories and attachments approved for this
machine by the machine manufacturer. Read, understand

and follow all instructions provided with the approved
accessory or attachment.

28. Data indicates that operators, age 60 years and above, are
involved in a large percentage of riding mower-related

injuries. These operators should evaluate their ability
to operate the riding mower safely enough to protect
themselves and others from serious injury.

29. If situations occur which are not covered in this manual, use
care and good judgment. Contact your customer service

representative for assistance.

SlopeOperation

Slopes are a major factor related to loss of control and tip-over
accidents which can result in severe injury or death. All slopes
require extra caution. If you cannot back up the slope or if you
feel uneasy on it, do not mow it.

For your safety, use the slope gauge included as part of this
manual to measure slopes before operating this machine on

a sloped or hilly area. If the slope is greater than 15 degrees as
shown on the slope gauge, do not operate this machine on that
area or serious injury could result.

Do:

1. Mow up and down slopes, not across. Exercise extreme
caution when changing direction on slopes.

2. Watch for holes, ruts, bumps, rocks, or other hidden
objects. Uneven terrain could overturn the machine. Tall
grass can hide obstacles.

3. Use slow speed. Choose a low enough speed setting so
that you will not have to stop or shift while on the slope.

Tires may lose traction on slopes even though the brakes
are functioning properly. Always keep machine in gear
when going down slopes to take advantage of engine
braking action.

4. Follow the manufacturer's recommendations for wheel
weights or counterweights to improve stability.

5. Use extra care with grass catchers or other attachments.
These can change the stability of the machine.

6. Keep all movement on the slopes slow and gradual. Do
not make sudden changes in speed or direction. Rapid

engagement or braking could cause the front of the
machine to lift and rapidly flip over backwards which could
cause serious injury.

7. Avoid starting or stopping on a slope. If tires lose traction,
disengage the blade(s) and proceed slowly straight down

the slope.

DoNot:

1. Do not turn on slopes unless necessary; then, turn slowly
and gradually downhill, if possible.

2. Do not mow near drop-offs, ditches or embankments. The
mower could suddenly turn over if a wheel is over the edge
of a cliff, ditch, or if an edge caves in.

3. Do not try to stabilize the machine by putting your foot on
the ground.

4. Do not use a grass catcher on steep slopes.

5. Do not mow on wet grass. Reduced traction could cause
sliding.

6. Do not shift to neutral and coast downhill. Over-speeding
may cause the operator to lose control of the machine

resulting in serious injury or death.

7. Do not tow heavy pull behind attachments (e.g. loaded
dump cart, lawn roller, etc.) on slopes greater than 5

degrees. When going down hill, the extra weight tends
to push the tractor and may cause you to loose control
(e.g. tractor may speed up, braking and steering ability are
reduced, attachment may jack-knife and cause tractor to

overturn).

4 I SECTION 2 -- IMPORTANT SAFE OPERATION PRACTICES

Children

1.

Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the
machine and the mowing activity. They do not understand

the dangers. Never assume that children will remain where
you last saw them.

a. Keep children out of the mowing area and in

watchful care of a responsible adult other than the
operator.

b. Be alert and turn machine off if a child enters the

area.

c. Before and while backing, look behind and down for

small children.

d. Never carry children, even with the blade(s) shut off.

They may fall offand be seriously injured or interfere

with safe machine operation.

e. Use extreme care when approaching blind corners,

doorways, shrubs, trees or other objects that may
blockyour vision of a child who may run into the

path of the machine.

f. To avoid back-over accidents, always disengage

the cutting blade(s) before shifting into Reverse.
If equipped, the "Reverse Caution Mode" should

not be used when children or others are around.

g. Keep children away from hot or running engines.

They can suffer burns from a hot muffler.

h. Remove key when machine is unattended to

prevent unauthorized operation.

2.

Never allow children under 14 years of age to operate this
machine. Children 14 and over should read and understand

the instructions and safe operation practices in this manual
and on the machine and should be trained and supervised
by an adult.

Towing

1. Tow only with a machine that has a hitch designed for
towing. Do not attach towed equipment except at the
hitch point.

2. Follow the manufacturers recommendation for weight
limits for towed equipment and towing on slopes.

3. Never allow children or others in or on towed equipment.

4. On slopes, the weight of the towed equipment may cause
loss of traction and loss of control.

5. Always use extra caution when towing with a machine
capable of making tight turns (e.g. "zero-turn" ride-on

mower). Make wide turns to avoid jack-knifing.

6. Travel slowly and allow extra distance to stop.

7. Do not shift to neutral and coast downhill.

Service

SafeHandling of Gasoline:

1. To avoid personal injury or property damage use extreme
care in handling gasoline. Gasoline is extremely

flammable and the vapors are explosive. Serious
personal injury can occur when gasoline is spilled on
yourself or your clothes which can ignite. Wash your skin
and change clothes immediately.

a. Use only an approved gasoline container.
b. Never fill containers inside a vehicle or on a truck

or trailer bed with a plastic liner. Always place
containers on the ground away from your vehicle

before filling.

c. When practical, remove gas-powered equipment

from the truck or trailer and refuel it on the ground.
If this is not possible, then refuel such equipment on
a trailer with a portable container, rather than from a
gasoline dispenser nozzle.

d. Keep the nozzle in contact with the rim of the fuel

tank or container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.

e. Extinguish all cigarettes, cigars, pipes and other

sources of ignition.

f. Never fuel machine indoors.
g. Never remove gas cap or add fuel while the engine

is hot or running. Allow engine to cool at least two
minutes before refueling.

h. Never over fill fuel tank. Fill tank to no more than 1/2

inch below bottom of filler neck to allow space for
fuel expansion.

i. Replace gasoline cap and tighten securely.

j. If gasoline is spilled, wipe it off the engine and

equipment. Move machine to another area. Wait 5
minutes before starting the engine.

k. To reduce fire hazards, keep machine free of grass,

leaves, or other debris build-up. Clean up oil or fuel
spillage and remove any fuel soaked debris.

I. Never store the machine or fuel container inside

where there is an open flame, spark or pilot light
as on a water heater, space heater, furnace, clothes

dryer or other gas appliances.

m. Allow a machine to cool at least five minutes before

storing.

GeneralService

1. Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless,
and deadly gas.

2. Before cleaning, repairing, or inspecting, make certain the
blade(s) and all moving parts have stopped. Disconnect the

spark plug wire and ground against the engine to prevent
unintended starting.

SECTION 2 -- IMPORTANT SAFE OPERATION PRACTICES S

3.

Periodically check to make sure the blades come to
complete stop within approximately (5) five seconds after
operating the blade disengagement control. If the blades
do not stop within the this time frame, your machine

should be serviced professionally by an authorized MTD
Service Dealer.

4. Check brake operation frequently as it is subjected to wear
during normal operation. Adjust and service as required.

5. Check the blade(s) and engine mounting bolts at frequent
intervals for proper tightness. Also, visually inspect blade(s)
for damage (e.g., excessive wear, bent, cracked). Replace
the blade(s) with the original equipment manufacturer's
(O.E.M.) blade(s) only, listed in this manual. "Use of parts

which do not meet the original equipment specifications
may lead to improper performance and compromise
safety!"

6. Mower blades are sharp. Wrap the blade or wear gloves,
and use extra caution when servicing them.

7. Keep all nuts, bolts, and screws tight to be sure the
equipment is in safe working condition.

8. Never tamper with the safety interlock system or other
safety devices. Check their proper operation regularly.

9. After striking a foreign object, stop the engine, disconnect
the spark plug wire(s) and ground against the engine.

Thoroughly inspect the machine for any damage. Repair
the damage before starting and operating.

10. Never attempt to make adjustments or repairs to the
machine while the engine is running.

11. Grass catcher components and the discharge cover are
subject to wear and damage which could expose moving
parts or allow objects to be thrown. For safety protection,
frequently check components and replace immediately
with original equipment manufacturer's (O.E.M.) parts only,

listed in this manual. "Use of parts which do not meet the
original equipment specifications may lead to improper
performance and compromise safety!"

12. Do not change the engine governor settings or over-speed
the engine. The governor controls the maximum safe

operating speed of the engine.

13. Maintain or replace safety and instruction labels, as
necessary.

14. Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.

15. According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),

this product has an Average Useful Life of seven (7) years,
or 270 hours of operation. At the end of the Average Useful
Life have the machine inspected annually by an authorized
service dealer to ensure that all mechanical and safety

systems are working properly and not worn excessively.
Failure to do so can result in accidents, injuries or death.

Donot modify engine

To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway

engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.

NoticeRegardingEmissions

Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)

are certified to operate on regular unleaded gasoline, and
may include the following emission control systems: Engine
Modification (EM), Oxidizing Catalyst (OC), Secondary Air
Injection (SAI) and Three Way Catalyst (TWC) if so equipped.

SparkArrestor

internal combustion engine and should not be used

_ ARNING! This machine is equipped with an

Ifa spark arrester is used, it should be maintained in effective
working order by the operator. In the State of California the
above is required by law (Section 4442 of the California Public

Resources Code). Other states may have similar laws. Federal laws
apply on federal lands.
A spark attester for the muffler is available through your
nearest engine authorized service dealer or contact the service

department, RO. Box 361131 Cleveland, Ohio 44136-0019.

on or near any unimproved forest-covered,
brushcovered or grass-covered land unless the

engine's exhaust system is equipped with a spark
arrester meeting applicable local or state laws (if

any).

WARNING! Your Responsibility--Restrict the use of this power machine to persons who read, understand and
follow the warnings and instructions in this manual and on the machine.

6 I SECTION 2 -- IMPORTANT SAFE OPERATION PRACTICES

SAVETHESEiNSTRUCTiONS!

SafetySymbols

This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the
machine before attempting to assemble and operate.

READ THE OPERATOR'S MANUAL(S)
Read, understand, and follow all instructions in the manual(s) before attempting to

assemble and operate

DANGER-- ROTATING BLADES
Never carry passengers. Never carry children, even with the blades off.

O

DANGER-- ROTATING BLADES

Always look down and behind before and while backing to avoid a back-over accident.

J

J

Lq

M

N

A

WARNING-- ROTATING BLADES

Do not put hands or feet near rotating parts or under the cutting deck. Contact with the
blade(s) can amputate hands and feet.

WARNING--THROWN OBJECTS
This machine may pick up and throw and objects which can cause serious personal injury.

WARNING--THROWN OBJECTS
This machine may pick up and throw and objects which can cause serious personal injury.

BYSTANDERS
Keep bystanders, helpers, children and pets at least 75 feet from the machine while it is in

operation.

WARNING-- SLOPE OPERATION

Do not operate this machine on a slope greater than 15 degrees.

WARNING-- HOT SURFACE

Engine parts, especially the muffler, become extremely hot during operation. Allow engine

and muffler to cool before touching.

DANGER -- ROTATING BLADES

To reduce the risk of injury, keep hands and feet away. Do not operate unless discharge cover
or grass catcher is in its proper place. If damaged, replace immediately.

WARNING-- TOWING
Avoid jack-knifing when towing, go slow and make wide turns.

SECTION 2 -- IMPORTANT SAFE OPERATION PRACTICES 7

co

-4

6

Z

I

Z

O

6

Z

"o

-4

or a corner of a building...I

I

|

,_ or a fence post

I i

i |

' FOldo,_ ',

' " .- 22

' diine

' a 15Oslope

.I

I
I

15°

Usethis page as a guide to determine slopeswhere youmay not operate safely.

WARNING! Do not operate your lawn mower on such slopes. Do not mow on inclines with a slope in excess of 15 degrees

(a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause serious injury. Operate riding

mowers up and down slopes, never across the face of slopes.

Assembly& Set-Up

Contents of Crate

3

One Lawn Tractor
One Lawn Tractor Operator's Manual

One Oil Drain Tube
One Kohler Engine Operator's

Manual

TractorSet-Up

Moving TheTractor Manually

Your tractor's transmission is equipped with a hydrostatic
relief valve for occasions when it is necessary to move the
tractor manually. Opening this valve permits the fluid in the
transmission to bypass its normal route, allowing the rear tires

to "freewheel." To open the hydrostatic relief valve, proceed as
follows:

1. Locate the hydrostatic bypass rod in the rear of the tractor.
See Fig. 3-1.

One DeckWash Hose Coupler

Shipping BraceRemoval

_ ARNING! Make sure the lawn tractor's engine is

1. Locate the shipping brace, if present, and warning tag

off, set the parking brake and remove the ignition
key before removing the shipping brace.

found on the right side of the cutting deck. See Fig. 3-2.

Figure 3=1

2. Pull the hydrostatic bypass rod outward, then down, to lock
it in place.

NOTE:The transmission will NOTengage when the hydrostatic
bypass rod is pulled out. Return the rod to its normal position

prior to operating the tractor.

CAUTION: Never attempt to move the tractor

manually without first opening the hydrostatic relief

valve. Doing so will result in serious damage to the
tractor's transmission.

Figure 3-2

2.

While holding the discharge chute with your left hand,
remove the shipping brace with your right hand by

grasping it between your thumb and index finger and
rotating it clockwise.

i_L WARNING! The shipping brace is used for

packaging purposes only. Remove and discard the
shipping brace before operating your lawn tractor.

WARNING! The mowing deck is capable of
throwing objects. Failure to operate the riding

mower without the discharge cover in the proper
operating position could result in serious personal
injury and/or property damage.

Connecting the Battery Cables

CALiFORNiA PROPOSiTiON 65 WARNING!

Battery posts, terminals, and related accessories
contain lead and lead compounds, chemicals known

to the State of California to cause cancer and

reproductive harm. Wash hands after handling.

connect the POSITIVE (Red) wire to its terminal first,

CAUTION: When attaching battery cables, always

followed by the NEGATIVE (Black) wire.

For shipping reasons, one or both battery cables on your
equipment may have been left disconnected from the terminals

at the factory. To connect the battery cables, proceed as follows:
NOTE:The positive battery terminal is marked Pos. (+). The

negative battery terminal is marked Neg. (-).
NOTE: If the positive battery cable is already attached, skip ahead

to step 2.

1. Remove the plastic cover, if present, from the positive
battery terminal and attach the red cable to the positive
battery terminal (+) with the bolt and hex nut. See Fig. 3-3.

CheckingTire Pressure

_i WARNING! Maximum tire pressure under any

• maintained at all times.
The tires on your tractor may be over-inflated for shipping

purposes. Reduce the tire pressure before operating the tractor.
Recommended operating tire pressure is approximately 10 p.s.i.

for the rear tires & 14 p.s.i, for the front tires. Check sidewall of tire
for maximum p.s.i.

circumstances is 30 psi. Equal tire pressure should be

Setting the DeckGaugeWheels

Move the tractor on a firm and level surface, preferably
pavement, and proceed as follows

1. Select the height position of the cutting deck by placing
the deck lift lever in the normally desired mowing height
setting (any of the six different cutting height notches on

the right fender).

2. Check the gauge wheels for contact or excessive clearance
with the surface below. The deck gauge wheels should

have between 1/4"and 1/2"clearance above the ground as
follows:

If the gauge wheels have excessive clearance or contact with the
surface, adjust as follows:

a. Raise the deck lift handle to its highest setting.
b. Remove the front and rear gauge wheels by

removing the lock nuts and shoulder screws which
secure them to the deck. See Fig. 3-4

Figure 3-3

2. Remove the plastic cover, if present, from the negative
battery terminal and attach the black cable to the negative
battery terminal (-) with the bolt and hex nut. See Fig. 3-3.

3. Position the red rubber boot over the positive battery
terminal to help protect it from corrosion.

NOTE: If the battery is put into service after the date shown
on top/side of battery, charge the battery as instructed in the
Maintenance section your Operator's Manual prior to operating

the tractor.

SECTION 3 -- ASSEMBLY& SET-UP

%

J

Figure 3-4

c. Place the deck lift lever in the desired mowing

height setting.

d. Reinsert the shoulder screw (with each gauge

wheel) into the index hole that leaves approximately
1/2-inch between the bottom of the wheel and the

pavement.

Refer to Leveling the Deck in the Maintenance & Adjustments
section of this manual for more detailed instructions regarding
various deck adjustments.

Adjusting the Seat

To adjust the position of the seat, pull up and hold the seat
adjustment lever. Slide the seat forward or rearward to the
desired position; then release the adjustment lever. Make sure

seat is locked into position before operating the tractor. See Fig.
3-5.

//

k_ j

Figure3-5

WARNING! Before operating the tractor, make sure
the seat is engaged in the seat-stop. Engage the

parking brake. Stand behind the machine and pull
back on seat until it clicks into place.

Gasand0il

The fuel tank is located under the hood and has a capacity of
three and-a-half gallons. Remove the fuel cap by turning it
counterclockwise. Use only clean, fresh (no more than 30 days

old), unleaded gasoline. Do not overfill the tank.

_IL ARNING! Use extreme care when handling

-- indoors or while the engine is hot or running.

NOTE: Your tractor is shipped with oil in the engine. However,
you MUST check the oil level before operating.

_ AUTION: Always check the engine oil level before

gasoline. Gasoline is extremely flammable and the

vapors are explosive. Never fuel the machine

Extinguish cigarettes, cigars, pipes and other
sources of ignition.

each use as instructed in the Kohler Owner's Manual.
Add oil as necessary. Failure to do so may result in

serious damage to your engine

SECTION3 -- ASSEMBLY& SET-UP 11

ControlsandFeatures

FuelTank Ca

Throttle/Choke Control

4

Systems indicator

Monitor

nition Switch

Module

Fuel Level

Brake Pedal

Cargo Net

Seat Adjustment

Storage ! 1 Cup Holder

Lawn Tractor controls and features are illustrated in Fig 4-1 and Brake Pedal

described on the following pages.

instructions in this manual, including the entire

_k ARNING! Read and follow all safety rules and

and instructions may result in personal injury.

Operation section, before attempting to operate

this machine. Failure to comply with all safety rules

Throttle/ChokeControl

The throttle/choke control is located on the left
side of the tractor's dash panel. This lever controls

the speed of the engine and, when pushed all the
way forward, closes the choke for cold starting.
When set in a given position, the throttle will
maintain a uniform engine speed.

NOTE:When operating the tractor with the
cutting deck engaged, be certain that the
throttle/choke control is always in the FAST
(rabbit) position.

Parking Brake/

Cruise Control Lever

Figure 4-1

The brake pedal is located on the left
front side of the tractor above the drive

pedal along the running board. The
brake pedal can be used for sudden
stops or setting the parking brake.

NOTE:The brake pedal must be fully
depressed to activate the safety interlock switch when starting
the tractor.

SeatAdjustmentLever(NotSeen)

The seat adjustment lever is located below the front/left of the
seat. The lever aIlows for adjustment of the fore to aft position of
the operator's seat. Refer to the Assembly and Set-Up section of

this manual for more detailed instructions.

Knob

Drive Pedal

Lift Lever

DeckLift Lever

Found on your tractor's right fender, the deck lift lever is used to
change the height of the cutting deck. To use, move the lever to
the left, then place in the notch best suited for your application.

Ignition SwitchModule

leave a running

i_ WARNING! Never

PTO, set parking brake, stop
engine and remove key to prevent

unintended starting.
To start the engine, insert the key

into the ignition switch and turn
clockwise to the START position.
Release the key into the NORMAL
MOWING MODE position once the

engine has fired.
To stop the engine, turn the ignition key counterclockwise to the

STOP position.

machine unattended.

Always disengage

CAUTION: Prior to operating the tractor, refer to

both Safety Interlock Switches and Starting The
Engine in the Operation section of this manual for

detailed instructions regarding the Ignition Switch
Module and operating the tractor in REVERSE

CAUTION MODE.

DrivePedal

The drive pedal is located on the right side
of the tractor, along the running board. Press

the drive pedal forward to cause the tractor
to travel forward. Ground speed is also
controlled with the drive pedal. The further
forward the pedal is pivoted, the faster the

tractor will travel. The pedal will return to its
original position when it's not pressed.

ReversePedal

The reverse pedal is located on the right
side of the tractor along the running board.
Ground speed is also controlled with the
reverse pedal. The further downward the
pedal is pivoted, the faster the tractor will

travel. The pedal will return to its original
position when it's not pressed.

| |

||

SystemsIndicator Monitor/
HourMeter[CD

When the ignition key is rotated out of
the STOP position but not into the START
position, the systems indicator monitor
displays the battery's output, in volts, on its
LCD for approximately five seconds, after

which it displays an hour glass and the hours of tractor operation.
Once the tractor is started, the monitor continually displays an
hour glass and the hours of tractor operation on its LCD.

NOTE: Hours of tractor operation are recorded any time the
ignition key is rotated out of the STOP position, regardless of

whether the engine is started.
The Indicator Monitor will also remind the operator of

maintenance intervals for changing the engine oil. The LCD will
alternately flash the recorded hours,"CHG" and "OIL" for five
minutes, after every 50 hours of recorded operation elapse. The

maintenance interval lasts for two hours (from 50-52,100-102,
150-152, etc.). The LCD will also flash as described above for five
minutes every time the tractor's engine has been started during
this maintenance interval. Before the interval expires, change
the engine oil as instructed in the Maintenance section of this

Operator's Manual.

Brake

If the Brake light illuminates when attempting to start the
tractor's engine, depress the brake pedal.

PT0(BladeEngage)

If the PTO light illuminates when attempting to start the tractor's
engine, move PTO lever into the disengaged (OFF) position.

0il (If EngineSoEquipped)

It is normal for the Oil light to illuminate while the engine is
cranking during start-up, but if it illuminate's during operation,

while the engine is running, stop the tractor immediately and
check the engine oil level as instructed in this Owner's Manual.

Battery

It is normal for the Battery light to illuminate while the engine is
cranking during start-up, but if it illuminate's during operation,
while the engine is running, the battery is in need of a charge
or the engine's charging system is not generating sufficient
amperage. Charge the battery as instructed in the Service

section of this manual or have the charging system checked by
your Cub Cadet dealer.

(:argoNet

The cargo netis located on the lower half of the dash and can be
used for storage.

SECTION4 -- CONTROLS AND FEATURES 13

FuelLevelIndicator

The Fuel Level Indicator is located on the left side of the
tractor's dash and indicates the amount of fuel in the gas

tank.

PTO/ BladeEngageKnob

PTO

Activating the PTO engages power to
the cutting deck or other (separately

available) attachments. Pull outward
on the PTO/Blade Engage knob to

activate it. Push the PTO/Blade Engage
knob inward to disengage the power
to the cutting deck or other (separately

available) attachments.
NOTE:The PTO/Blade Engage knob

must be in the disengaged (OFF)
position when starting the engine.

_ J

Located in the center of the tractor's dash panel below the
steering wheel, the Parking Brake/Cruise Control lever is used
to engage the parking brake and the cruise control Refer to
the Operation section of this manual for detailed instructions
regarding the parking brake.

NOTE:The parking brake must be set if the operator leaves the
seat with the engine running or the engine will automatically

shut off.
NOTE: Cruise control can NOT be engaged at the tractor's

fastest ground speed. If the operator should attempt to do so,
the tractor will automatically decelerate to the fastest optimal

mowing ground speed.

OFF ON

unattended. Always disengage PTO, set parking

i_ WARNING! Never leave a running machine

brake, stop engine and remove key to prevent
unintended starting.

SECTION 4-- CONTROLS AND FEATURES

Operation

TO AVOID SERIOUS INJURY OR DEATH

• GOUPANDDOWNSLOPES,NOTACROSS.

• AVOIDSUDDENTURNS.

• DONOTOPERATETHEUNITWHEREITCOULDSLIPORTIP.

• IF MACHINESTOPSGOINGUPHILL,STOPBLADE(S)
ANDBACKDOWNHILLSLOWLY.

• KEEPSAFETYDEVICES(GUARDS,SHIELDS,AND
SWITCHES,ETC.) IN PLACEANDWORKING.

• REMOVEOBJECTSTHATCOULDBETHROWNBYTHEBLADE(S).

• KNOWLOCATIONANDFUNCTIONOFALLCONTROLS.

• BESUREBLADE(S)ANDENGINEARESTOPPEDBEFORE
PLACINGHANDSORFEETNEARBLADE(S).

• BEFORELEAVINGOPERATOR'SPOSITION,DISENGAGE
BLADE(S),ENGAGEPARKINGBRAKE,SHUTOFFAND

REMOVEKEY.

READ OPERATOR'S MANUAL

Safety InterlockSwitches

This tractor is equipped with a safety interlock system for the
protection of the operator. If the interlock system should ever

malfunction, do not operate the tractor. Contact your Cub Cadet
dealer.

The safety interlock system prevents the engine from
cranking or starting unless the parking brake is engaged,

and the PTO (Blade Engage) knob is in the disengaged
(OFF) position.

The engine will automatically shut off if the operator leaves
the seat before engaging the parking brake.

The electric PTO (Blade Engage) clutch will automatically
shut off if the operator leaves the tractor's seat with the

PTO (Blade Engage) knob in the engaged (ON) position,
regardless of whether the parking brake is engaged.

With the ignition key in the NORMAL MOWING position,
the electric PTO (Blade Engage) clutch will automatically

shut off if the PTO (Blade Engage) knob is moved into the
engaged (ON) position with the drive pedal in position for

reverse travel.

Startingthe Engine

NOTE: Refer to the Assembly & Set-Up section of this ma nual for
Gasoline and Oil fill-up instructions.

1. Insert the tractor key into the ignition switch module.

2. Place the PTO (Blade Engage) knob in the disengaged (OFF)
position.

3. Engage the tractor's parking brake.

4. Activate the Throttle/Choke control.

5. Turn the ignition key clockwise to the START position.
After the engine starts, release the key. It will return to the
NORMAL MOWING position.

_ CAUTION: Do NOT hold the key in the START

6. After the engine starts, deactivate the choke.

NOTE: Do NOT leave the choke on while operating the tractor.
Doing so will result in a "rich" fuel mixture and cause the engine
to run poorly.

position for longer than ten seconds at a time. Doing
so may cause damage to your engine's electric

starter.

Stopping the Engine

engine and disconnect the spark plug wire(s).

_i ARNING! If you strike a foreign object, stop the

1. If the blades are engaged, place the PTO/Blade Engage

2. Place the throttle control near the SLOW position

3. Turn the ignition key counterclockwise to the STOP

4. Remove the key from the ignition switch to prevent

Thoroughly inspect the machine for any damage.

Repair the damage before restarting and operating

knob in the disengaged (OFF) position.

position.

unintended starting.

interlock system is malfunctioning. This system was

WARNING! Do not operate the tractor if the

designed for your safety and protection.

15

DrivingTheTractor

and sudden stops.

i_ WARNING! Avoid sudden starts, excessive speed

1. Lightly press the brake pedal to release the parking brake.
Move the throttle lever into the FAST(rabbit) position.

2. To travel FORWARD,slowly press the upper portion of the
drive pedal forward until the desired speed isachieved. See

Fig.5-1.

Pedal

ReverseCautionMode

The REVERSE CAUTION MODE position of the key switch module
allows the tractor to be operated in reverse with the blades (PTO)

engaged.
NOTE: Mowing in reverse is not recommended.

the tractor in the REVERSECAUTIONMODE. Always
WARNING! Useextreme caution while operating

look down and behind before and while backing. Do
not operate the tractor when children or others are

around. Stop the tractor immediately if someone
enters the area.

To use the REVERSECAUTION MODE:
NOTE:The operator MUST be seated in the tractor seat.

1. Start the engine as previously instructed on the previous
page.

2. Turn the key from the NORMAL MOWING (Green) position
to the REVERSECAUTION MODE (Yellow) position of the
key switch module. See Fig. 5-2.

Figure 5-1

To travel in REVERSE, check that the area behind is clear
then slowly depress the lower portion of the drive pedal
with the ball of your foot (NOTyour heel) until the desired
speed is achieved. See Fig. 5-1.

CAUTION: Do NOT attempt to change the

direction of travel when the tractor is in motion.

Always bring the tractor to a complete stop before

moving the tractor from forward to reverse or vice

versa.
WARNING! Do not leave the seat of the tractor

without first placing the PTO/Blade Engage knob in
the disengaged (OFF) position and engaging the

parking brake. If leaving the tractor unattended, also

turn the engine offand remove the ignition key.

Indicator NO CHILDREN AROUND

Light BUTTON'="_"

REVERSEPUSH

Stop

Position

Reverse

i_ Push Button

Reverse

Caution Mode

Position

Start

Position

Figure 5=2

3. Press the REVERSE PUSH BUTTON (Orange, Triangular
Button) at the top, right corner of the key switch module.
The red indicator light at the top, left corner of the key

switch module will be ON while activated. See Fig. 5-2.

4. Once activated (indicator light ON), the tractor can be
driven in reverse with the cutting blades (PTO) engaged.

5. Always look down and behind before and while backing to
make sure no children are around. After resuming forward
motion, return the key to the NORMAL MOWING position.

The REVERSE CAUTION MODE will remain activated until:

a. The key is placed in either the NORMAL MOWING

position or STOP position or

b. The operator leaves the seat.

J

SECTION 5-- OPERATION

Driving OnSlopes

Refer to the SLOPE GAUGE on page 8 to help determine slopes
where you may operate the tractor safely.

CruiseControl

while traveling in reverse.

_ ARNING! Never engage the cruise control lever

excess of 15 degrees (a rise of approximately 2-1/2

i_ll WARNING! Do not mow on inclines with a slope in

feet every 10 feet). The tractor could overturn and

cause serious injury.

Mow up and down slopes, NEVER across.
Exercise extreme caution when changing direction on

slopes.
Watch for holes, ruts, bumps, rocks, or other hidden

objects. Uneven terrain could overturn the machine. Tall
grass can hide obstacles.

Avoid turns when driving on a slope. Ira turn must be
made, turn down the slope. Turning up a slope greatly

increases the chance of a roll over.
Avoid stopping when driving up a slope. If it is necessary

to stop while driving up a slope, start up smoothly and
carefully to reduce the possibility of flipping the tractor

over backward.

Engagingthe ParkingBrake/
Settingthe CruiseControl

NOTE:The parking break and cruise control are controlled by
the same lever. If using the brake, when the parking brake/cruise

control lever the parking brake will engage. If using the drive
pedal, when the parking brake/cruise control lever the cruise
control will engage.

To set

the cruise control:

1.

Slowly press the drive pedal with your right foot until the
desired speed is achieved.

2.

Lightly press the parking brake/cruise control lever
downward and hold it in that position.

3.

Remove your foot from the drive pedal.

4.

Release pressure from the parking brake/cruise control
lever

After completing step 3, the drive pedal should remain in the
down position and the tractor will maintain the same forward

speed. If it doesn't, the cruise control is not engaged. Repeat
steps 1-4 to engage the cruise control.

To disengage the cruise control, lightly press the drive pedal or
the brake pedal.

NOTE: Cruise control can not be set at the tractor's fastest
ground speed. If the operator should attempt to do so, the

tractor will automatically decelerate to the fastest optimal
mowing ground speed.

To change the direction of travel from forward to reverse when
cruise control is engaged, press the brake pedal to disengage

the cruise control and bring the tractor to a complete stop. Then
slowly press the reverse pedal with the ball of your foot to travel

in reverse.

Parking Brake

NOTE:The parking brake must be set if the operator leaves the
seat with the engine running or the engine will automatically

shut off.
To set the parking brake:

1. Press the brake pedal completely down with your left foot
and hold it in that position.

2. Push the parking brake/cruise control lever downward and
hold it in that position.

3. Remove your foot from the brake pedal.

4. Release pressure from the parking brake/cruise control
lever.

After completing step 3, the brake pedal should remain in the
down position. If it doesn't, the parking brake is not engaged.

Repeat steps 1-4 to engage the parking brake.
To disengage the parking brake, lightly press the brake pedal.

WARNING! Never leave a running machine

unattended. Always disengage PTO, set parking
brake, stop engine and remove key to prevent
unintended starting

Usingthe DeckLift Lever

To raise the cutting deck, move the deck lift lever to the left, then
place it in the notch best suited for your application.

Operatingthe Headlights

The lamps are ON whenever the ignition key is rotated out of
the STOP position. The lamps turn OFF when the ignition key is
moved to the STOP position.

SECTION S -- OPERATION 17

Engagingthe PTO

Engaging the PTO transfers power to the cutting deck or other
(separately available) attachments. To engage the PTO:

1. Move the throttle control lever to the FAST (rabbit)
position.

2. Pull the PTO/Blade Engage knob outward into the engaged
(ON) position. See Fig. 5-3.

OFF

For best results it is recommended that the first two laps be
cut with the discharge thrown towards the center. After the
first two laps, reverse the direction to throw the discharge

to the outside for the balance of cutting. This will give a
better appearance to the lawn.

Do NOT attempt to mow heavy brush and weeds or
extremely tall grass. Your tractor is designed to mow lawns,

NOT clear brush.
Keep the blades sharp and replace the blades when worn.

Figure 5=3

NOTE: Always operate the tractor with the throttle lever in the
FAST (rabbit) position for the most efficient use of the cutting
deck or other (separately available) attachments.

Mowing

WARNING! To help avoid blade contact or a

thrown object injury, keep bystanders, helpers,

children and pets at least 75 feet from the machine

while it is in operation. Stop machine if anyone
enters the area.

The following information will be helpful when using the cutting
deck with your tractor.

discharge of materials toward roads, sidewalks,

i_ WARNING! Plan your mowing pattern to avoid

bystanders and the like. Also, avoid discharging
material against a wall or obstruction which may

cause discharged material to ricochet back toward

the operator.

Do not mowat high ground speed, especially ira mulch kit
or grass collector is installed.

Do not cut the grass too short. Short grass is prone to weed
growth and yellows quickly in dry weather.

Always operate the tractor with the throttle lever in the
FAST (rabbit) position while mowing

J

SECTION S-- OPERATION

Maintenance&Adjustments

MaintenanceSchedule

6

Before

Eachuse

Every

10 Hours

Every

25 Hours

Every

50 Hours

Every

I00 Hours

,/

CheckEngineOil Level

CheckAir Filter for Dirty, Loose or Damaged Parts

Cleanand Re-oil Air Filter's Foam Predeaner V /

ReplaceAir Filter Element _/

Change EngineOiland ReplaceOil Filter

Clean Battery Terminals y / y /

Lube Front A×ies and Rims _

Clean Engine CoolingFins _

Lube Front Deck Wheels V / V /

Prior

toStoring

,/Clean Hood/Dash Louvers

Lube Deck Spindles _

Lube Pedal Pivot Points _

CheckSpark Plug Condition &Gap _

ReplaceFuel Filter

Maintenance Changingthe EngineOil

WARNING! Before performing any maintenance or

repairs, disengage PTO, set parking brake, stop

engine and remove key to prevent unintended

starting.

Engine

Refer to the Kohler Owner's Manual for all engine maintenance
procedures and instructions.

NOTE: Maintenance, repair, or replacement of the emission
control devices and systems which are being done at owner's
expense may be performed by any engine repair establishment
or individual. Warranty repairs must be performed by a Cub

Cadet Dealer.

_ ARNING! If the engine has been recently run, the

NOTE:The oil filter should be changed at every oil change
interval. To complete an oil change, proceed as follows:

1. Run the engine for a few minutes to allow the oil in the

2.

engine, muffler and surrounding metal surfaces will

be hot and can cause burns to the skin. Exercise
caution to avoid burns.

crankcase to warm up. Warm oil will flow more freely and
carry away more of the engine sediment which may have

settled at the bottom of the crankcase. Use care to avoid
burns from hot oil.

Open the tractor's hood and locate the oil drain port on the
right side of the engine.

19

3.

Pop open the protective cap on the end of the oil drain
valve to expose the drain port. See Fig 6-1.

\

Figure 6-1

4. Remove the oil fill cap/dipstick from the oil fill tube.

5. Push the oil drain hose (packed with this manual) onto the
oil drain port. Route the opposite end of the hose into an

appropriate oil collection container with at least a 2.5 quart
capacity, to collect the used oil.

6. The engine is equipped with either a twist-and-pull drain
port or a tabbed drain port. If your engine has the twist-
and-pull drain go to step a. If your engine is equipped with
the tabbed drain go to step b.

a. Turn the oil drain valve 1/4-turn, then pull outward to

begin draining oil. After the oil has finished draining,
push the end of the oil drain valve back in and turn
1/4-turn to secure it back in place. Re-cap the end of
the oil drain valve to keep debris from entering the

drain port.

b. Pinch the tabs on the oil drain valve, then pull

outward to begin draining oil. After the oil has
finished draining, push the end of the oil drain valve

back in, until the tabs click into place. Re-cap the end
of the oil drain valve to keep debris from entering
the drain port.

7. After the oil has finished draining, push the end of the oil
drain valve back in, until the tabs click into place. Re-cap
the end of the oil drain valve to keep debris from entering

the drain port.

B.

Replace the oil filter as instructed in the Kohler Owner's
Manual.

9.

Refill the engine with new oil. Refer to the Kohler Owner's
Manual for information regarding the volume and weight

of engine oil

Air Cleaner

Service the pre-cleaner and cartridge/air cleaner element as
instructed in the Kohler Owner's Manual.

SparkPlug

The spark plug should be cleaned and the gap reset once a

season. Refer to the Kohler Owner's Manual for correct plug type
and gap specifications.

Hydrostatic Transmission

The hydrostatic transmission is sealed at the factory and is

maintenance-free. The fluid level cannot be checked and the
fluid cannot be changed.

Battery

CALIFORNIA PROPOSITION 65 WARNING!

Battery posts, terminals, and related accessories
contain lead and lead compounds, chemicals known
to the State of California to cause cancer and

reproductive harm. Wash hands after handling.

The battery is sealed and is maintenance-free. Acid levels cannot

be checked and fluid can not be added.

Always keep the battery cables and terminals clean and
free of corrosive build-up.

,J

After cleaning the battery and terminals, apply a light coat
of petroleum jelly or grease to both terminals.

disconnect the NEGATIVE (Black) wire from it's

CAUTION: If removing the battery for cleaning,

terminal first, followed by the POSITIVE (Red) wire.
When re-installing the battery, always connect the

POSITIVE (Red) wire its terminal first, followed by the

NEGATIVE (Black) wire. Be certain that the wires are
connected to the correct terminals; reversing them

could result in serious damage to your engine's
alternating system.

Cleaningthe Tractor

Any fuel or oil spilled on the machine should be wiped off
promptly. Do NOT allow debris to accumulate around the cooling
fins of the engine, the transmission's cooling fan or on any other

part of the machine, especially the belts and pulleys.

Smart JetTM

Your tractor's deck is equipped with a water port on its surface as
part of its deck wash system.

Use the Smart Jet TM to rinse grass clippings from the deck's
underside and prevent the buildup of corrosive chemicals.
Complete the following steps AFTER EACH MOWING:

1. Drive the tractor to a level, clear spot on your lawn, near
enough for your garden hose to reach.

chute is directed AWAY from your house, garage,

CAUTION: Make certain the tractor's discharge

parked cars, etc.

1. Disengage the PTO (Blade Engage), set the parking brake
and stop the engine.

2. Thread the hose coupler (packaged with your tractor's
Operator's Manual) onto the end of your garden hose.

SECTION 6 -- MAINTENANCE & ADJUSTMENTS

3. Attach the hose coupler to the water port on your decks Lubrication

surface. See Fig. 6-2.

Figure 6=2

4.

Turn the water on.

5.

While sitting in the operator's position on the tractor, start
the engine and place the throttle lever in the FAST (rabbit)

position.

6. Move the tractor's PTO (Blade Engage) into the ON position.

7. Remain in the operator's position with the cutting deck
engaged for a minimum of two minutes, allowing the
underside of the cutting deck to thoroughly rinse.

8. Move the tractor's PTO (Blade Engage) into the OFF
position.

9. Turn the ignition key to the STOP position to turn the
tractor's engine off.

10. Turn the water off and detach the hose coupler from the
water port on your deck's surface.

11. Repeat step 4- step 11 on the opposite side of the cutting
deck.

After cleaning your deck with the Smart Jet TM system, return to
the operator's position and engage the PTO.Keep the cutting
deck running for a minimum of two minutes, allowing the
underside of the cutting deck to thoroughly dry.

_L ARNING! Before lubricating, repairing, or

brake, stop engine and remove key to prevent
unintended starting.

FrontWheels

inspecting, always disengage PTO, set parking

Each of the front wheel axles and rims is equipped with a
grease fitting. See Fig. 6-3. Lubricate with a No. 2 multi-purpose
grease applied with a grease gun after every 25 hours of tractor
operation.

j_

/ /

\

Figure 6=3

Pivot Points& Linkage

Lubricate all the pivot points on the drive system, parking brake
and lift linkage at least once a season with light oil.

I)eckWheels

Each of the tractor deck's front gauge wheels is equipped with
a grease fitting. Lubricate with a No. 2 multi-purpose grease
applied with a grease gun after every 25 hours of tractor

operation

SECTION 6 -- MAINTENANCE & ADJUSTMENTS 21

DeckSpindle

Grease fittings can be found on each deck spindle. See Fig. 6-4.
Lubricate with 251H EP grease or an equivalent No. 2 multi-
purpose lithium grease. Using a grease gun, apply two strokes

(minimum) or sufficient grease to the spindle shaft.

Figure 6-4

Adjustments

WARNING! Shut the engine off, remove the

ignition key and engage the parking brake before
making adjustments. Protect your hands by using

heavy gloves when handling the blades.

NOTE: Check the tractor's tire pressure before performing
any deck leveling adjustments. Refer to Tires on page 25 for

information regarding tire pressure.

Determine the approximate distance necessary for proper
adjustment and proceed, if necessary.

1. Loosen (thread outward) the hex lock nut on the end of the
deck hanger rod. See Fig. 6-5.

f

Figure 6-5

2. To raise the front of the deck, tighten (thread inward) the
inner hex nut against the front hanger bracket.

3. To Iowerthe front of the deck, loosen (thread outward) the
hex nut, away from the front hanger bracket.
See Fig. 6-5.

4. Retighten the lock nut against the hex nut when proper
adjustment is achieved.

Levelingthe Deck(FrontToRear)

The front of the cutting deck is supported by a stabilizer bar that
can be adjusted to level the deck from front to rear. The front of

the deck should be between 1/4"and %" lower than the rear of the
deck. Adjust if necessary as follows:

1. Park the tractor parked on a firm, level surface and place
the deck lift lever in the middle position.

2. Rotate the blade nearest the discharge chute so that it is
parallel with the tractor.

3. Measure the distance from the front of the blade tip to the
ground and the rear of the blade tip to the ground. The

first measurement taken should be between 1/4"and %" less
than the second measurement.

SECTION 6 -- MAINTENANCE & ADJUSTMENTS