Cub Cadet 7284 User Manual
Operator’s Manual
SERIES 7000
COMPACT TRACTOR
MODEL 7284
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning
forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark
arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective
working order by the operator. In the State of California the abo ve is req uired by law (Secti on 4 442 of the Cal ifo rnia Publi c
Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the
muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box
361131Cleveland, Ohio 44136-0019.
CUB CADET LLC P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 [www.cubcadet.com]
PRINTED IN U.S.A. FORM NO. 769-01158
: This unit i s equipped with an internal combustion engine an d should not be used on or near any unimproved
(3/04)
TABLE OF CONTENTS
TO THE OWNER ................................ ... ... ... ... .... ... ............................................................. .. .. 2
CALLING SERVICE INFORMATION ...................................................................................... 2
RECORDING MODEL AND SERIAL NUMBER INFORMATION . ... ... ... ... .... ... ... ... .... ... ... ... ... . 3
IMPORTANT SAFE OPERATION PRACTICES ..................................................................... 4
SAFETY LABELS ................................................................................................................... 7
SECTION 1: CONTROLS AND FEATURES ...................................................... ... .... ... ... ... ... . 9
SECTION 2: OPERATION .................................................................................................... 15
SECTION 3: ADJUSTMENTS .............................................................................................. 24
SECTION 4: TRACTOR MAINTENANCE ............................................................................ 27
SECTION 5: ENGINE INFORMATION AND MAINTENANCE ............................................. 40
SECTION 6: SPECIFICATIONS ........................................................................................... 46
SECTION 7: OPTIONAL EQUIPMENT AND ACCESSORIES ............................................. 48
WARRANTY ........................................................................................................................ 52
TO THE OWNER
This Operator’s Manual is an important part of your new tractor. The information contained in this
manual has been prepared in detail to help you better understand the features, correct operation,
adjustments, and maintenance of your tractor. The performance and dependability of this tractor rely
greatly on the manner in which it is operated and maintained. Therefore, it is recommended that all
operators of the tractor carefully read this manual and fully understand its operation. Also keep the
manual available for reference to ensure proper operation, and that maintenance procedures are
performed as scheduled to assure the tract or’s optimal mechanical condition.
NOTE: All references to LEFT, RIGHT, FRONT, and REAR, unless specifically stated otherwise,
indicate that relative position on the tractor when facing forward while seated in the operator’s seat.
Your authorized Cub Cadet dealer is interested in the pe rformance you receiv e from yo ur tractor, a nd
with the maintenance needed to ensure the satisfactory operation of your tractor. The dealer has
trained service personnel familiar with the latest servicing information, is equipped with the latest
tools, and has a complete line of genu ine Cub Cadet service parts which assure proper fit and high
quality.
CALLING SERVICE INFORMATION
The engine manufacturer is responsible for all engine-related issues with regards to performance,
power-rating, and specifications.
If you have difficulties with the tractor and/or equipment; have any questions regarding the operation
or maintenance of this equipment; or desire additional information not found in this manual, contact
your dealer. If you need assistance in locating a dealer in your area, contact the Customer Dealer
Referral Line by calling:
1-877-282-8684
Or you may contact Cub Cadet via the internet by logging on to our Web Site at:
www.cubcadet.com
Before calling your dealer, make sure that you have your model number(s) and manufacturing date
available for the dealer.
2
RECORDING MODEL AND SERIAL NUMBER INFORMATION
Product identification plates are provided for major components of your tractor. The numbers on these
plates are important if your tractor should require dealer service, or if you need additional information
on your tractor. Prior to using your tractor for the first time, record the numbers from the identification
plates in the appropriate spaces provided below.
• The tractor model plate is located on the right frame rail behind the right front tire.
• The engine model/serial number plate and engine information plate are located on the right side
of the engine above and aside the injection pump (below the air cleaner).
• The transmission serial plate is located on right brake drum cover behind the right rear wheel.
• The ROPS information plate is located on the left vertical leg of the ROPS.
Tractor Model Plate:
Model Number Mfg. Date (Serial No.)
Engine Information:
Engine Model Serial Number
Transmission Serial Plate:
Serial Number
ROPS Information Plate:
ROPS Serial No.
TRACTOR MODEL PLATE
XXXXXXXXXXX XXXXXXXXXX
Model Number Mfg. Date
CUB CADET LLC
P. O. BOX
www.cubcadet.com
DEALER LOCATOR PHONE NUMBER:
361131
CLEVELAND, OH 44136
877-282-8684
TRANSMISSION SERIAL PLATE
ROPS INFORMATION PLATE
3
IMPORTANT SAFE OPERATION PRACTICES
WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF
NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF
YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE YOUR UNIT. FAILURE TO COMPLY WITH THESE
INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. WHEN YOU SEE THIS SYMBOL,
HEED ITS WARNING.
WARNING: The engine exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to the S tate of California to cause cancer, birth defects or other
reproductive harm.
DANGER: Your tractor was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. To help prevent accidents, read and take the following precautions before
operating this tractor. Failure to observe the following safety instructions could result in serious
injury or death.
1. GENERAL OPERATION
• Read, understand, and follow all instructions in
the operator’s manual and on the machine
before starting. Keep this manual in a safe
place for future and regular reference.
• Only allow responsible individuals familiar with
the instructions to operate the machine. Know
controls and how to stop the machine quickly.
• Use the roll bar and seat belt for safe operation.
Overturning the tractor without a roll bar, or with
a roll bar and the seat belt unfastened, can
result in death or injury.
• Always use the seat belt, except if the roll bar
has been removed or, if applicable, the roll bar
is in the folded position.
• Use the handholds and running boards when
getting on and off the tractor to help prevent
accidental falls. Keep the running boards clear
of mud and debris.
• Wear sturdy, rough-soled work shoes. Never
operate the tractor in bare feet, sandals, or
sneakers.
• Do not wear loose fitting clothes or jewelry.
They can be caught in moving parts.
• Do not allow anyone but the operator to ride on
the tractor. There is no safe position on the
tractor for additional riders.
• Keep all safety decals clean and readable.
Replace any missing, illegible, or damaged
safety decals.
• Do not operate the machine while under the
influence of alcohol or drugs.
• Use only accessories approved for this
machine by the manufacturer. Read,
understand and follow all instructions provided
with the approved accessory.
• Before starting the tractor, engage the parking
brake, place the PTO switch in the "OFF"
position, place the lift control lever in the down
position, and make certain any remote control
valve levers are in the neutral position.
• Always sit in the tractor seat when starting the
engine or operating controls. Do not start the
engine or operate controls while standing
beside the tractor.
• Never tamper with safety devices. Check their
proper operation regularly. Contact your Cub
Cadet dealer if safety devices malfunction.
• Avoid accidental contact with control pedals
while the engine is running, as this can cause
unexpected movement of the tractor.
• Never leave a running machine unattended.
Always disengage the PTO, engage the
parking brake, and stop engine before
dismounting.
• Never park the tractor on a steep incline.
• Pull only from a drawbar or the lower hitch links
in the down position. Make certain the drawbar
pin is locked in place. Pulling from the rear axle
of the tractor or any point above the axle could
cause the tractor to overturn.
4
• Maintain the weight balance of the tractor.
Install front end weights to counterbalance
heavy implements attached to the three point
hitch. Do not operate the tractor with a light
front end.
• Any towed vehicle with a total weight exceeding
that of the tractor should be equipped its own
braking system that is operational from the
tractor seat.
• Do not leave equipment in the raised position.
• Watch for traffic when operating near or
crossing roadways. If local laws permit road
travel, use the flashing hazard lights and SMV
signs when traveling on public roadways.
• Make certain all tractor lights are illuminated
when operating at night.
• Always watch where you are going, especially
at blind corners, trees, or other obje cts that can
obscure your vision.
• Check overhead clearance carefully before
driving under power lines, wires, bridges or low
hanging tree branches, before entering or
leaving buildings, or in any other situation
where the operator and/or roll bar may be
struck, which could result in serious injury.
• To avoid upsets, drive the tractor with care and
at a safe speed. Use extra caution when
operating over rough ground, when crossing
ditches or slopes, and when turning corners.
• If the tractor becomes stuck, use reverse to
free the tractor to prevent tractor upset.
2. SLOPE OPERATION
Slopes are a major factor related to loss of control
and tip-over accidents which can result in severe
injury or death. All slopes require extra caution. If
you cannot back up the slope or if you feel uneasy
on it, do not operate this unit on that area or serious
injury could result.
DO:
• Operate up and down slopes, not across.
• Remove obstacles such as rocks, limbs, etc.
• Watch for holes, ruts or bumps. Uneven terrain
could overturn the machine. Tall grass can hide
such obstacles.
• Place the transmission in the low range. when
climbing or descending slopes. Always keep
machine in gear when going down slopes to
take advantage of engine braking action.
• Follow the manufacturers recommendations for
counterweights to improve stability.
• Keep all movement on the slopes slow and
gradual. Do not make sudden changes in
speed or direction. Rapid engagement or
braking could cause the fron t of the machine to
lift and rapidly flip over backwards which could
cause serious injury.
• Avoid starting or stopping on a slope. If tires
lose traction, disengage the PTO and proceed
slowly straight down the slope.
DO NOT:
• Do not turn on slopes unless necessary; then,
turn slowly and gradually downhill, if possible.
• Do not mow near drop-offs, ditches or
embankments. The mower could suddenly turn
over if a wheel goes over the edge of a cliff or
ditch, or if an edge caves in.
3. CHILDREN
• Tragic accidents can occur if the operato r is not
alert to the presence of children. Children are
often attracted to the machine. Never assume
children will remain where you last saw them.
• Keep children out of the operating area and in
watchful care of an adult other than the
operator.
• Be alert and turn machine off if children enter
the area.
• Before and when backing, look behind and
down for small children.
• Never carry children. They may fall off and be
seriously injured or interfere with safe machine
operation.
• Never allow children under 14 years old to
operate the machine. Children 14 years and
over should only operate machine under close
parental supervision and proper instruction.
• Use extra care when approaching blind
corners, shrubs, trees or other objects that may
obscure your vision of a child or other hazard.
• Remove key when machine is unattended to
prevent unauthorized operation.
4. OPERATING THE PTO
• When operating PTO driven equipment,
disengage the PTO, stop the engine, and wait
until the PTO stops before dismounting the
tractor and disconnecting the equipm ent.
• Do not wear loose fitting clothing when
operating the PTO or when near rotating
equipment.
5
• To prevent injury, do not adjust, u nclog, clean,
or service PTO driven equipment while the
tractor engine is running.
• Make certain all PTO shields are always installed.
5. SAFETY FRAME (ROPS)
Your tractor is equipped with a rollover protective
structure (ROPS) which must be maintained in a
fully functional condition. Use care when driving
through doorways or spaces with a low overhead.
• Never modify the ROPS in any way.
• Never attempt to straighten or reweld any part
of the main frame or retaining brackets that
have been damaged. Doing so may weaken
the structure and endanger your safety.
• Never secure any parts on the main frame or
attach the safety frame with anything other than
the special fasteners specified.
• Never attach ropes, chains, or cables to the
ROPS for pulling purposes.
• Although the ROPS provides you the maximum
protection possible, never take unnecessary risks.
6. SERVICE
• Use extreme care in handling gasoline and
other fuels. They are extremely flammable and
the vapors are explosive. Use only an approved
container.
• Never remove fuel cap or add fuel with the
engine running.
• Replace fuel cap securely and wipe off any
spilled fuel before starting the engine as it may
cause a fire or explosion.
• Extinguish all cigarettes, cigars, pipes and
other sources of ignition.
• Never refuel the machine indoors because fuel
vapors will accumulate in the area.
• Never store the fuel container or machine
inside where there is an open flame or spark,
such as a gas hot water heater, space heater
or furnace.
• The cooling system is under pressure. Never
remove the radiator cap when the system is
hot. Slowly turn the cap the to the first stop to
release pressure before removing the cap.
• Escaping hydraulic fluid under pressure can
penetrate the skin. If fluid is injected into the
skin, seek immediate medical attention. Do not
use your hand to check for leaks. Use a piece
of cardboard or paper.
• Never run a machine inside a closed area.
• To reduce fire hazard, keep the tractor free of
any debris build-up. Clean up oil or fuel spillage.
• Before cleaning, repairing or inspecting, make
certain all moving parts have stopped. Keep all
nuts, bolts and screws tight to be sure the
equipment is in safe working condition.
• Never tamper with safety devices. Check their
proper operation regularly.
• Check brake operation frequently. Adjust and
service as required.
• Engine components become hot during
operation and can cause a burn. Allow to cool
down before touching.
• Do not change the engine governor settings or
overspeed the engine. Excessive engine
speeds are dangerous.
• Observe proper disposal laws and regulations.
Improper disposal of fluids and materials can
harm the environment and the ecology.
• Prior to disposal, determine the proper method
to dispose of waste from your local
Environmental Protection Agency. Recycling
centers are established to properly dispose of
materials in an environmentally safe fashion.
• Use proper containers when draining fluids. Do
not use food or beverage containers that may
mislead someone into drinking from them.
Properly dispose of the containers immediately
following the draining of fluids.
• DO NOT pour oil or other fluids into the ground,
down a drain or into a stream, pond, lake or
other body of water. Observe Environmental
Protection Agency regulations when disposing
of oil, fuel, coolant, brake fluid, filters, batteries,
tires and other harmful waste.
• We do not recommend the use of a pressure
washer or garden hose to clean your unit. They
may cause damage to electrical components;
spindles; pulleys; bearings; or the engine. The
use of water will result in shortened life and
reduce serviceability.
WARNING:
read, understand and follow the warnings and instructions in this manual and on the machine.
- YOUR RESPONSIBILITY: Restrict the use of this power machin e to persons who
6
SAFETY LABELS
1.
KNOW THE OPERATING AND SAFETY INSTRUCTIONS IN THE
OPERATORS'S MANUAL AND ON THE TRACTOR
2.
MOVE THROTTLE TO MID POSITION AND DEPRESS BRAKE PEDAL.
3.
TURN KEY TO THE START POSITION.
1.
DISENGAGE PTO AND SET PARKING BRAKE.
2.
MOVE THROTTLE CONTROL TO MID POSITION AND TURN KEY OFF.
•
GO UP AND DOWN SLOPES, NOT ACROSS.
•
AVOID SUDDEN TURNS.
•
DO NOT OPERATE UNIT WHERE IT COULD SLIP OR TIP.
•
IF MACHINE STOPS GOING UPHILL, STOP PTO AND BACK DOWN HILL SLOWLY.
•
DO NOT MOW WHEN CHILDREN OR OTHERS ARE AROUND.
•
DO NOT ALLOW PASSENGERS ON THE TRACTOR AT ANY TIME.
•
LOOK DOWN AND BEHIND BEFORE AND WHILE BACKING.
•
KEEP SAFETY DEVICES [GUARDS, SHIELDS, AND SWITCHES] IN PLACE AND WORKING.
•
REMOVE OBJECTS THAT COULD BE THROWN BY THE BLADES.
•
KNOW LOCATION AND FUNCTION OF ALL CONTROLS.
•
BE SURE THE BLADES AND THE ENGINE ARE STOPPED BEF ORE PLAC ING HANDS
OR FEET NEAR BLADES.
•
BEFORE LEAVING OPERATOR'S POSITION, DISENGAGE PTO, ENGAGE BRAKE LOCK,
SHUT OFF ENGINE AND REMOVE KEY.
•
SLOW DOWN FOR TURNS, ROUGH GROUND AND SLOPES TO AVOID UPSET.
•
ON PUBLIC ROADS USE SMV EMBLEM AND HAZARD LIGHTS.
STARTING INSTRUCTIONS
.
STOPPING INSTRUCTIONS
WARN
AVOID SERIOUS INJURY OR DEATH
READ OPERATOR'S MANUAL
I
NG
IGNITION
S
.
T
O
P
INSTRUCTION AND WARNING LABEL
LOCATED ON RUNNING BOARD TUNNEL COVER
WARNING
KEEP HANDS
AND CLOTHING
AWAY FROM
ROTATING FAN
AND BELTS TO
PREVENT
SERIOUS INJURY
FAN WARNING LABEL
LOCATED ON EACH
SIDE OF RADIATOR
WARNING
EXPLOSION AND INJURY CAN
RESULT FROM THE USE OF
STARTING AIDS WITH HOT GLOW
PLUGS, DO NOT INJECT GASOLINE
OR ETHER IN AIR INTAKE
STARTING AID
WARNING LABEL
LOCATED UNDER HOOD
7
SAFETY LABELS (Cont.)
WARNING
To avoid personal injury, keep PTO shield in place.
Pull only from draw bar. pulling from any other point can cause rear overturn.
Disengage PTO and stop engine before servicing tractor, or implements,
or attaching or detaching implements.
FAILURE TO FOLLOW ANY OF THE INSTRUCTIONS ABOVE CAN CAUSE
SERIOUS INJURY TO THE OPERATOR, OR OTHER PERSONS.
LOCATED ON REAR PTO SHIELD
PTO WARNING LABEL
WARNING
BATTERIES CON TAIN ACID AN D EXPLOSIVE GAS.
EXPLOSION CAN RESULT FROM SPARKS, FLAM ES,
OR W RONG CABLE CONNECTIONS. TO CONNECT
JUM PER CABLES OR CHARGER SEE MANUAL FOR
CORRECT PROCEDURE. FAILURE TO FOLLOW THE
ABOVE INSTRUCTIONS CAN CAUSE SERIOUS
PERSONAL INJURY OR DEATH.
BATTERY WARNING LABEL
LOCATED UNDER HOOD
WARNING
When improperly operated this tractor can roll over or upset. Use of the ROPS and
seat belt minimize the possibilit y of injury or death if roll over or upset occurs. For
low cle ara nce use onl y, the ROPS can be lowe red. No prote cti on is provide d in t his
posit ion and the seat belt should not be fast ened. For a ll other use s, secure the ROP S
in the upright posit ion and fasten the seat belt.
ROLL OVER WARNING LABEL
LOCATED ON RIGHT/REAR FENDER
8
SECTION 1: CONTROLS AND FEATURES
FLOORBOARD AND DASH PANEL MOUNTED CONTROLS
M
L
K
J
H
G
A
B
C
D
E
F
Figure 1
Steering Wheel
A
PTO Switch
B
Throttle Handle
C
Ignition Switch
D
Brake Pedal
E
Forward/Reverse Pedal
F
Seat Adjustment Lever
G
Differential Lock Pedal
H
Parking Brake Lever
J
Hazard Light Switch
K
Headlight Switch
L
Instrument Panel
M
* Steering Wheel and Seat Phantomed For Clarity
9
NOTE: References to LEFT and RIGHT indicate
that side of the tractor when facing forward while
seated in the drivers seat. Reference to FRONT
indicates the grille end of the tractor; to REAR, the
drawbar end.
A. Steering Wheel
The steering wheel is centered on the dash panel. It
is used to change the direction ( left or right) of the
tractor while driving.
NOTE: This tractor is equipped with hydraulic
power steering. With this feature, the cap and
spokes of the steering wheel may change position.
B. PTO Switch
OFF - The engine and electrical system is turned
off.
ON - The electrical system and glow plugs are
energized.
START- The starter motor will turn the engine.
Release the key immediately when the
engine starts
E. Brake Pedal
Brake Pedal
Symbol
Figure 4
PTO
Switch
Symbol
Figure 2
The PTO switch is a rocker type switch located to
the right of the steering wheel on the dash panel.
Push the top of the PTO switch downward to
engage the PTO. Push the bottom of the switch
downward to disengage.
C. Throttle Handle
This symbol indicates the
fast position.
This symbol indicates the
slow position.
The throttle handle is located to the right of the
steering wheel on the dash panel. When set in a
given position, a uniform engine speed will be
maintained. Rotate the handle rearward to increase
the engine speed.
D. Ignition Switch
NOTE: To prevent accidental starting and/or battery
discharge, remove the key from the ignition switch
when the tractor is not in use.
The ignition switch has three positions as follow:
OFF
STOP
ON-PREHEAT
The brake pedal is located at the front of the right
floor board. Depress to engage the tractor brakes
and neutralize the hydrostatic transmission. Fully
depress the brake pedal to activate the safety
interlock switch when starting the tractor.
F. Forward/Reverse Pedal
The forward/reverse pedal is a self neutralizing
rocker style pedal located along the right floor board.
Forward Reverse
Pedal Pedal
Symbol Symbol
Figure 5
Forward
Slowly press down on the front of the pedal to start
moving forward. The forward ground speed of the
tractor is directly affected by the distance the front
of the pedal is depressed.
Reverse
WARNING: Check behind the tractor to
be sure the area is clear of people, pets
or obstacles and use a slower speed to
maintain control of the tractor when
traveling in reverse.
Press down on the rear of the pedal to move in
reverse.
Figure 3
START
G. Seat Adjustment Lever
The seat adjustment lever is located beneath the
left side of the seat. This lever is used to adjust the
seat forward or backward.
10
H. Differential Lock Pedal
Diff. Lock
Pedal
Symbol
Figure 6
Located at the rear of the left floor board, the
differential lock pedal engages the transmission
differential lock.
The differential lock is used to gain additional traction when operating the tractor on wet or loos e soil.
When the pedal is depressed the rear wheels of the
tractor are prevented from rotating independently of
one another.
WARNING: When operating with the
differential lock engaged, the tractor
will be difficult to steer. Do not drive
the tractor on roadways or at high
speeds with the differential lock
engaged.
The parking brake lever is located below the
steering wheel in the dash panel. With the brake
pedal fully depressed, push the parking brake lever
downward and release the brake pedal to lock the
parking brake.
K. Hazard Light Switch
Figure 8
The hazard light switch is a rocker type switch
located to the left of the steering whee l on the dash
panel. Push the top of the hazard light switch
downward to activate the flashing amber lights.
WARNING: Always activate the flashing hazard lights when operating the
tractor on, or near, roadways.
L. Headlight Switch
NOTE: Disengagement of the differential lock is
recommended prior to turning the tractor on grass
or other maintained surfaces — tire damage to the
turf could occur.
J. Parking Brake Lever
Parking
Brake
Symbol
Figure 7
Figure 9
The headlight switch is a rocker type switch located
to the left of the steering wheel on the dash panel.
Push the top of the headlight switch downward to
turn on the headlights, instrument pan el lights, and
tail lights.
11
M. Instrument Panel
7
3
12
10
2
8
6
Figure 10
1. Fuel Gauge
The fuel gauge monitors, at 20 second intervals,
the fuel level in the fuel tank. The needle pointing to
the right indicates a full tank. The ignition switch
must be in the ON position to read the fuel gauge.
2. T achometer
The tachometer shows the engine speed in revolutions per minute (RPM). Optimal engine operating
speed is approximately 2500-3600 RPM. When
operating PTO driven attachments the RPM indicator needle should be within the green range on the
tachometer dial.
3. Battery Indicator Light
The bulb illuminates to indicate the battery is being
discharged. If this warning lamp comes on during
operation, check the charging system for possible
causes and/or contact your Cub Cadet dealer.
4. Engine Oil Pressure Light
This warning lamp indicates low engine oil pressure. If the bulb comes on while the engine is
running, stop the engine immediately and check for
possible causes. NOTE: The bulb may illuminate
when the ignition switch is in the ON position, but
should turn off when the engine is started.
5. Engine Coolant Temperature Light
Illumination of this warning lamp indicates the
engine coolant temperature has risen above the
prescribed operating range. If the light comes on
while operating the tractor, eliminate all loads and
try cooling the engine by running at mid throttle for
a few minutes. Stop the engine and allow to cool;
then check for possible causes (e.g. low coolant
level, plugged radiator screen).
6. Parking Brake Indicator Light
The bulb illuminates when the ignition switch is in
the ON position and the brake pedal is depresse d.
The light flashes if attempting to start the tractor
with the brake not engaged.
4
11
9
5
10
1
7. PTO Indicator Light
Light comes on in a fixed mode whenever the PTO
switch is in the ON position, with the following
exceptions.
• The light will illuminate in a flashing mode if
attempting to start the tractor with the PTO
switch in the ON position.
• The light will change to the flashing mode when
the PTO switch is on, but the reverse pedal has
been engaged and the reverse override has
NOT been engaged.
8. Hour Meter
The hour meter records the hours and tenths of an
hour (right most digit) that the tractor has been
operated. The hourmeter is activated whenever the
tractor engine is running. Keep a record of the
hours of operation and maintenance performed to
ensure all maintenance procedures are completed
according to the schedule in this manual.
9. PTO Reverse Override Indicator
This warning lamp illuminates to indicate the PTO
reverse override switch has been depressed and
the PTO reverse override is engaged. Use extra
caution when operating PTO driven attachments
while traveling in the reverse direction.
10. Hazard Light Indicator
Arrows will flash in conjunction with the amber hazard
lights when the hazard light switch is turned on.
11. Glow Plug Indicator Light
Illuminates when the ignition switch is turn ed to the
ON position. The light remains lit for a preset time
while the glow plugs heat the precombustion
chambers of the diesel engine.
12. Cruise Control Indicator Light (Optional)
12
FENDER MOUNTED CONRTOLS AND FE ATURES
A
G
H
J
B
C
K
N
L
O
D
K
E
G
F
M
H
J
Figure 11
Fuel Fill Cap
A
PTO Reverse Override Switch
B
PTO Selection Lever
C
Hydraulic Lift Lever
D
Trans. Hi/Lo Shift Lever
E
Cup Holder
F
Hand Holds
G
Amber Hazard Lights
H
Tail Lights (Red)
J
Reverse Lights (White)
K
Storage Tray
L
Foldable ROPS
M
Seat Belt
N
Auxiliary Hydraulic Control HandleO
A. Fuel Fill Cap
The fuel fill cap is located on the left fender beside
the operator’s seat.
WARNING: Never fill the fuel tank to
the top of the filler neck. Expansion
could result in overflow, allowing
highly flammable fuel to come in
contact with the operator.
B. PTO Reverse Override Switch
The PTO reverse override switch is located on the
left fender. Depress the front of the switch to
engage the override which allows the PTO to
operate while the tractor is traveling in the reverse
direction. Once activated, this function remains
activated until the ignition switch is turned to
the OFF position, regardless of the number of
times the PTO is turned off using the PTO switch.
WARNING: Use EXTREME caution
when operating PTO driven attachments while traveling in the reverse
direction.
C. PTO Selection Lever
The PTO selection lever is located on the left
fender.
• Push the lever forward to engage the mi d PTO.
• Push the lever rearward to engage the rear
PTO.
• Move the lever to the center position to
simultaneously engage both the rear PTO and
mid PTO.
D. Hydraulic Lift Lever w/Position Control
The hydraulic lift lever is located on the right fender.
This lever controls the position of the three point
hitch lift arms. There is a direct relationship
between the position of the lever and the height
position of the installed equipment.
• To lower the lift arms, move the lift lever
forward until the desired height setting is
attained.
• To raise the lift arms, move the lift lever
rearward until the desired height setting is
attained.
13
E. Transmission Hi/Lo Range Shift Lever
The Hi/Lo range shift lever is located on the right
fender. The lever has two speed range settings and
a neutral position. The lever must be shifted into
either the high or low range prior to depressing the
forward/reverse pedal to drive the tractor.
• Push the lever forward to shift into the high
range.
• Push the lever rearward to shift into the low
range.
• Move the lever to the center position to shift
into the neutral position.
WARNING: Never attempt to shift the
range lever when the tractor is in
motion.
F. Cup Holder
The cup holder is located on the right fender .
G. Hand Holds
Hand holds are built into both the left and right hand
fender covers. The handles can be used to assist in
mounting and dismounting the tractor.
H. Amber Hazard Lights
The hazard lights are located on each side of the
ROPS bar. The lights illuminate in a flashing mode
when the hazard light switch is turned on. Always
use the hazard lights when it is necessary to warn
others that the tractor is being operated in the area.
J. Tail Lights
The tail lights illuminate when the ignition switch is
in the ON position and the headlight switch is
turned on.
K. Reverse Lights
The reverse lights illuminate when the tractor is
being operated in the reverse direction.
L. Storage Tray
The storage tray is located behind the seat. Use the
tray to carry small loose articles while operating the
tractor.
M. Foldable ROPS (Rollover Protective Structure)
ROPS is installed to prevent or reduce injuries to
the operator should the tractor accidentally overturn. The foldable feature allows the ROPS to be
lowered when operating in areas with low overhead clearance. The protection provided by the
ROPS is minimized if the seat belt is not used and
eliminated when in the folded position.
N. Seat Belt
The seat belt, properly adjusted and used in
conjunction with the Rollover Protective Structure
(ROPS), can greatly reduce the risk of serious
injury or death to the operator if an accidental
tractor overturn occurs.
WARNING: DO NOT use the seat belt if
the ROPS is in the folded position, or
the structure has been removed from
the tractor.
O. Auxiliary Hydraulic Control Handle
The auxiliary hydraulic control handle is located on
the front of the right hand fender cover. Use this
handle to control the movement of attachments
connected to the auxiliary hydraulic system of the
tractor.
14
SECTION 2: OPERATION
ROLLOVER PROTECTIVE STRUCTURE (ROPS)
This tractor is equipped with a foldable Rollover
Protection Structure (ROPS) and seat belts. When
used together they are effective in reducing injuries
to the operator in the event of an accidental tractor
rollover. The safety provided by the ROPS is
minimized if the seat belt is not properly adjusted
AND buckled. Refer to ADJUSTMENTS for seat
belt adjustment.
ROPS
FOLDING THE ROPS
The foldable ROPS feature allows the operator to
quickly lower the ROPS to operate in areas where
there is low overhead clearance. However, the
ROPS should be used in the lowered position only
when absolutely necessary. Operate with the
ROPS in the ‘up’ position whenever possible.
WARNING: A folded ROPS does not
provide rollover protection. When the
ROPS is in the folded position, the seat
belt must NOT be used.
Reposition the ROPS as follows:
• Slightly loosen the two hex screws on the front
of the ROPS to relieve their pressure on the
ROPS. See Figure 13.
• Remove the two internal cotter pins, an d, while
supporting the ROPS, withdraw the clevis pins.
See Figure 13. Carefully lower the ROPS.
• Reinstall the clevis pins and cotter pins for
storage.
Figure 12
WARNING: Always wear the seat belt
when operating the tractor equipped
with a ROPS. However, if the ROPS is in
the folded position or has been removed, the seat belt must not be used.
Use the following guidelines when using a tractor
equipped with a ROPS:
• Be aware of overhead clearances in the area of
operation. Check for clearance of door (or gate)
openings and other overhead objects such as
utility lines and tree branches. Overhead
objects could catch the ROPS and upset the
tractor.
• Do not modify the ROPS by drilling holes for, or
welding accessories to the structure.
• Do not use the ROPS to pull objects with the
tractor. Use ONLY the tractor drawbar for
pulling.
• In the event of an accident, have the ROPS
carefully inspected and, if nece ssary, replaced
by your Cub Cadet dealer. Do not attempt to
repair the ROPS.
CLEVIS
PIN
INTERNAL
COTTER PIN
HEX
SCREW
CLEVIS
PIN
Figure 13
To raise the ROPS:
• Remove internal cotter pins and clevis pins and
lift the ROPS into position.
• Insert the clevis pins and secure with the
internal cotter pins.
• Tighten the hex screws against the ROPS.
15
SAFETY INTERLOCK SYSTEM
• Do not smoke while refueling the tractor.
This tractor is equipped with a safety interlock
system for the protection of the operator. If the
interlock system should ever malfunction, do not
operate the tractor. Contact your authorized Cub
Cadet Dealer. The safety interlock system prevents
the engine from cranking or starting unless the
brake pedal is fully depressed, and the PTO is
“OFF”.
• The safety interlock system will shut off the
engine if the operator leaves the seat before
engaging the parking brake.
• The safety interlock system will shut off the
engine if the operator leaves the seat with the
PTO “ON”, regardless of whether the brake
lock is engaged.
NOTE: The PTO switch must be moved to the
“OFF” position to restart the engine. If the
reverse override function had been activated, it
will remain activated until the ignition switch is
turned to the "OFF" position.
• The safety interlock system will shut off the
PTO if the reverse control pedal is depressed,
unless the reverse override function is
activated.
FUELING THE TRACTOR
Fill the fuel tank with only clean, fresh, diesel fuel.
Fuel with a cetane number of 45 is recommended,
but fuel with a minimum cetane number of 40 is
acceptable. To ensure the freshness of the fuel,
purchase fuel in a quantity that can be used within
30 days.
NOTE: DO NOT USE KEROSENE OR GASOLINE
in your diesel engine. Damage to the engine will
occur.
Generally a good grade Number Two Diesel Fuel
should be used in your diesel engine. However, in
extremely cold temperatures a quality Number One
Diesel Fuel, or a blend of Number One and Number
Two Diesel fuels should be used. In most areas,
diesel fuel is properly blended for seasonal use as
ambient temperatures change. Therefore, it is
important to monitor fuel purchases so that
seasonal grade fuels are not carried over after the
average ambient temperature has changed.
WARNING: Never fill the fuel tank to
the top of the filler neck. Expansion
could result in overflow through the
vents in the cap, allowing fuel to come
in contact with the operator.
• Do not fill the fuel tank when the engine is
running or while the engine is hot.
• The fuel fill cap is located on the fender to the
left of the seat. Unscrew the fuel cap and fill
tank from an approved container. Do not fill the
fuel tank to capacity. Allow room for expansion.
• Tighten the fuel cap securely, and immediately
wipe up any spilled fuel.
• To minimize condensation, keep the fuel tank
as full as possible without filling to capacity. It is
a good practice to fill the fuel tank at the end of
the day to reduce overnight condensation.
• Do not allow the fuel tank to run dry. Running
out of fuel requires bleeding air and repriming
the fuel system.
WARNING: Fuel in the engine injection
system is under high pressure. If not a
qualified mechanic, do not attempt to
service the fuel injection system. Do
not use your hand to check for leaks.
NEW TRACTOR BREAK-IN PROCEDURES
Proper care during the first hours of operation will
help to assure optimal performance from your new
tractor.
• Never operate a new engine immediately under
full load. Allow the engine to warm up.
• Avoid operating the engine for prolonged
periods at either high or low speeds with no
load.
• Use the transmission’s low speed range for
heavy loads to avoid lugging of the engine due
to overload.
• Closely monitor the engine oil and coolant
levels, and keep filled to the recommended
levels.
• After the first ten hours of operation, check all
of the front and rear wheel bolts. If necessary,
retighten to the following torque:
Front Wheels — 55 ft. lbs.
Rear Wheels — 80 ft. lbs.
• Perform all break-in maintenance procedures
found in the MAINTENANCE section.
16
Loading...