Operators Manual
High Pressure Washer
CUB CADET P.O. BOX 368023 CLEVELAND, OHIO 44136-9722 (www.cubcadet.com)
IMPORTANT:
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
MODEL 1400E
2
1
4
3
10
7
12
14
5
6
9
15
11
13
8
1
Model 1400E OVERVIEW
Item Description
1. Vario Spray wand
2. Spray wand extension
3. Rotating spray wand
4. Trigger gun
5. Trigger gun safety lock
6. High pressure hose
7. Mobile adapter bracket (qty. 2)
8. Power cord & GFCI
9. Hose/cord caddy
10. Trigger gun holder
11. Detergent reservoir
12. On/Off switch
13. Detergent filter & suction tube
14. High pressure outlet
15. Water inlet
16. Package of 6 screws
(not pictured)
17. Rotating spray wand
2
IMPORTANT PRECAUTIONS – Read First!
Safety Warnings
When using this product, basic precautions should always be followed:
• Read all the instructions before using
the product.
• High pressure jets can be dangerous
if subject to misuse. The jet must not
be directed at persons, animals,
electrical devices, or the machine itself.
• To reduce the risk of injury, do not
operate the machine near children.
• Learn how to stop the machine and
release pressure quickly. Be thoroughly
familiar with the controls.
• Stay alert — watch what you are doing.
• Wear safety goggles.
• Do not use acids,
solvents, or any
flammable material in this product.
These products can cause physical
injuries to the operator and irreversible
damage to the machine.
• Do not operate the product when
fatigued or under the influence of
alcohol or drugs.
• Do not stand on unstable surfaces.
Stand with both feet balanced at all
times.
• To reduce the risk of electrocution, keep
all connections dry and off the ground.
Do not touch plug with wet hands.
• The Gun Safety Lock PREVENTS
the trigger from accidentally being
engaged. This safety feature DOES
NOT lock trigger in the on position.
Extension Cords
Use a sufficient gauge: Up to 25 ft = 12/2
AWG; 25 to 50 ft = 10/2 AWG. Use only
extension cords that are intended for
outdoor use. These extension cords are
identified by the marking “Acceptable for
use with outdoor appliances; store
indoors while not in use.” Use only
extension cords having an electrical rating
not less than the rating of the product. Do
not use damaged extension cords.
Examine extension cord before using and
replace if damaged. Do not abuse
extension cord and do not yank on any
cord to disconnect. Keep cord away from
heat and sharp edges. Always disconnect
the extension cord from the receptacle
before disconnecting the product from the
extension cord. If you are using an
extension cord, it should always be
completely unwound from the cable drum.
Ground Fault Circuit
Interrupter (GFCI) Protection
This unit is supplied with a portable
Ground Fault Circuit Interrupter (GFCI).
UL indicates that the power cord has
been investigated for compliance with the
applicable provisions of UL 943, Third
Edition (Standard for Ground Fault Circuit
Interrupters) and other applicable
standards. If power is interrupted in the
line, the GFCI will automatically reclose
the circuit to the load after power is
restored. Depending on the GFCI model,
it may be necessary to manually operate
the reset button to restore power to the
GFCI load circuit.
This Product Is
Double Insulated
In a double-insulated product, two
systems of insulation are provided instead
of grounding. No grounding method is
provided on a double-insulated product,
nor should a method for grounding be
added to the product. Servicing a doubleinsulated product requires extreme care
and knowledge of the system, and should
be done only by qualified service
personnel. Replacement parts for a
double-insulated product must be
identical to the parts they replace.
A double-insulated product is marked
with the words, “DOUBLE INSULATED.”
Caution
• Follow the maintenance instructions specified in the manual.
• This machine has been designed
for use with cleaning detergents
supplied or recommended by the
manufacturer. The use of other
cleaning detergents may affect
the operation of the machine and
void the warranty.
Specifications
Operating pressure 1400 PSI
Water volume 1.6 GPM
Voltage 120 V
Amp draw 14 AMPS
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Precautions . . . . . . . . . . . . . . . . . . . . . . . . .1-3
Assembly Instructions . . . . . . . . . . . . . . . . . . .3
Operating Instructions . . . . . . . . . . . . . . . . . . .4
Ground Fault Circuit Interrupter Instructions . .5
Using the Accessories . . . . . . . . . . . . . . . . . . .5
Working with Detergents . . . . . . . . . . . . . . . . .6
Shut Down and Clean-Up . . . . . . . . . . . . . . . .7
Taking a Break . . . . . . . . . . . . . . . . . . . . . . . . .7
Winterizing and Long-Term Storage . . . . . . . .7
Cleaning Tips . . . . . . . . . . . . . . . . . . . . . . . .8-9
Optional Cleaning Accessories . . . . . . . . . . . .9
Troubleshooting . . . . . . . . . . . . . . . . . . . .10-11
Model 1400 E INDEX NEVER!
Never point nozzle at people or animals.
Never drink alcohol or use drugs while
operating this equipment.
Never operate while standing in water.
Never touch plug with wet hands.
Never let electrical connections rest in water.
Never operate pressure washer without the
water turned on
Never use hot water
Dealer Referral Line
1-877-835-7841
or visit our website: www.cubcadet.com
17
3
ASSEMBLY INSTRUCTIONS
Water Supply
(Cold Water Only)
• Water hose must be at least 3/4 inch
in diameter.
• Flow rate of water supply must not fall
below 2.5 GPM (gallons per minute).
• Flow rate can be determined by
running the water for one minute into
an empty 5-gallon container.
IMPORTANT PRECAUTIONS
– continued
• The water supply temperature must
not exceed 104°F/40°C.
• Never use the pressure washer to draw
in water contaminated with solvents, e.g.
paint thinners, gasoline, oil, etc.
• Always prevent debris from being drawn
into the unit by using a clean water
source.
Step 1 Attach one adapter bracket
to pressure washer by aligning holes on
adapter bracket with posts on the pressure
washer as shown. Tighten the two screws.
Step 2 Place detergent reservoir between
adapter brackets as shown. Attach second
adapter bracket.
OPERATING INSTRUCTIONS
4
Step 1 Connect the high pressure hose to
the unit’s high pressure outlet.
Step 2 Insert the spray wand of
your choice into the wand extension.
Press in against the spring tension and
twist into the locked position.
Step 3 Connect garden hose
to unit’s water inlet.
Step 4 Connect garden hose
to the cold water source and turn
water on completely.
Step 5 Plug the power cord into the power
outlet. Trigger the gun to eliminate trapped air,
wait for a steady flow of water to emerge from
the spray nozzle.
Step 6 Turn on the pressure
washer (I).
The motor starts only if
the trigger of the gun is pulled
and shuts off when the trigger is
released.
Step 4 Slide the spray wand extension
into the gun. Turn the wand collar onto the gun
threads until tight.
Step 3 Attach handle onto top of
adapter brackets. Press down to lock.
Tighten with screws as shown.
Note: Hose/cord caddy and trigger
gun holder must be on opposite sides.
USING THE ACCESSORIES
5
This wand features a 0º pencil jet which rotates 360º for maximum dirt cutting action,
effectively increasing cleaning performance up to 50%. This wand combines the cleaning
performance of a 0º pencil jet with the surface coverage of a wide angle nozzle.
Not recommended for soft materials, siding, painted surfaces, decks or autos.
Rotating spray wand
Vario spray wand
The Vario spray wand allows you to adjust the cleaning pressure. To clean at maximum
pressure, the Vario wand must be positioned to the high pressure setting (+).
To apply detergent, the wand must be positioned to the low pressure setting (-).
For lower
pressure turn
wand collar in the
minus (-) direction.
For higher
pressure turn
wand collar in the
plus (+) direction.
GFCI INSTRUCTIONS
6
WORKING WITH DETERGENTS
Detergents can only be applied at low pressure (-).
Step 1 Install the Vario spray wand.
Set the Vario spray wand to the low pressure
setting (-) by turning the wand collar. The
wand must be set in the low pressure (-)
position to apply detergents.
Step 3 Turn on the pressure washer.
Pull trigger to operate unit: Liquid detergent
is drawn into the unit and mixed with water.
Apply detergent to work area. Do not allow
detergent to dry on surface.
For best results see Cleaning
Tips on pages 8 & 9 for specific
information on how to clean
different surfaces.
Always Use Cub Cadet
Detergents for Best Results.
Cub Cadet biodegradable detergents are
specially formulated to protect the
environment and your pressure washer.
The special formula won’t clog the suction
tube filter and will protect the internal
parts of the pressure washer for a longer
life. For Cub Cadet Detergents, check
your retailer or call:
Step 2 Fill the detergent reservoir with
Cub Cadet detergent. Place the filter end of
detergent suction tube into the detergent
reservoir
Caution
Never use:
• Bleach, Chlorine products and other
corrosive chemicals
• Liquids containing solvents
(i.e., paint thinners, gasoline, oils)
• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the unit and
will damage the surface being cleaned.
WARNING
TO AVOID SERIOUS INJURY,
NEVER POINT SPRAY NOZZLE
AT YOURSELF, OTHER PERSONS OR ANIMALS.
Dealer Referral Line
1-877-835-7841
or visit our website: www.cubcadet.com
Step 1 Plug the Ground
Fault Circuit Interrupter (GFCI)
into a working outlet.
Step 2 Press “TEST”, then
press “RESET” to assure proper
connection to power.
Note:
The actual
appearance
of the GFCI
may be
different
from this
illustration.
The following Cub Cadet detergents
are available:
• Vehicle Wash • Deck Wash
Part # KR-9103501 Part # KR-9103502
• Degreaser • All Purpose Cleaner
Part # KR-9103503 Part # KR-9103504
Step 2 Insert
detergent suction tube
into 1 gallon of fresh
water. Siphon water at
low pressure for one
minute.
Step 3 Turn
the switch to off (O)
position and unplug
cord from outlet.
Turn off the water
source.
Step 4 Press
trigger to release
water pressure.
SHUTTING DOWN & CLEAN-UP
7
WINTERIZING AND LONG-TERM STORAGE
1. Disconnect all water connections.
2. Turn on the machine for a few
seconds, until the water which
had remained in the pump exits.
Turn off immediately.
3. Do not allow high pressure hose
to become kinked.
4. Store the machine and accessories in
a room which does not reach freezing
temperatures.
Caution: Failure to follow the above
directions will result in damage to the
pump assembly and accessories.
TAKING A BREAK... five minutes or more
Step 5 Disconnect
the garden hose from the
water inlet on the unit.
Step 2
Turn pressure
washer to off
(O) position.
Step 6 Disconnect the high pressure hose from the
high pressure outlet and engage the gun safety lock.
Step 1
Engage gun
safety lock.
Step 1 Remove
detergent suction
tube from detergent
reservoir.
8
CLEANING TIPS
Deck Cleaning
(with or without detergent)
Pre-rinse deck and surrounding area with
fresh water. If using Cub Cadet Deck Wash,
place detergent suction tube directly into
cleaning solution and apply to surface at
low pressure. For best results, limit your
work area to smaller sections of
approximately 25 square feet. Allow Cub
Cadet Deck Wash to remain on surface 1-3
minutes. Do not allow detergent to dry on
surface. Rinse at high pressure in a long
sweeping motion keeping the spray nozzle
approximately 3-6 inches from the cleaning
surface. Always clean from top to bottom
and from left to right. When moving on to
a new section of the cleaning surface, be
sure to overlap the previous section to
eliminate stop marks and ensure a more
even cleaning result.
Caution: Do not use Rotating spray wand
on wood surface as it may cause damage.
House Siding
(with or without detergent)
Pre-rinse cleaning surface with fresh water.
If using Cub Cadet
All Purpose Cleaner
,
place detergent suction tube directly into
cleaning solution and apply to surface at
low pressure (for best results, limit your
work area to sections of approximately 6
feet and always apply detergent from
bottom to top). Allow Cub Cadet
All Purpose
Cleaner
to remain on surface 1-3 minutes.
Do not allow detergent to dry on surface, if
surface appears to be drying, simply wet
down surface with fresh water. If needed,
use special Wash Brush Attachment to
remove stubborn dirt. Rinse at high
pressure from top to bottom in an even
sweeping motion keeping the spray nozzle
approximately 6 inches from the cleaning
surface.
Caution: Do not use Rotating spray wand
on siding as it may cause damage.
Cement Patios,
Brick and Stone
(with or without detergent)
Pre-rinse cleaning surface with fresh water.
If using Cub Cadet All Purpose Cleaner,
place detergent suction tube directly into
cleaning solution and apply to surface at
low pressure. For best results, limit your
work area to smaller sections of
approximately 25 square feet. Allow Cub
Cadet All Purpose Cleaner to remain on
surface 1-3 minutes. Do not allow detergent
to dry on surface. Rinse at high pressure in
a sweeping motion keeping the spray
nozzle approximately 3-6 inches from the
cleaning surface. Always clean from top to
bottom and from left to right. For removing
extremely stubborn stains, use Cub Cadet
Rotating spray Wand.
Cars, Boats & Motorcycles
(with or without detergent)
Pre-rinse vehicle with fresh water. If using
Cub Cadet Vehicle Wash, place detergent
suction tube directly into cleaning solution
and apply to surface at low pressure.
For best results, clean one side of vehicle
at a time and always apply detergent from
bottom to top, do not allow detergent to
dry on surface. If needed, use special Wash
Brush Attachment to remove stubborn dirt.
Rinse at high pressure in a sweeping
motion keeping the spray nozzle approximately 6-8 inches from the cleaning
surface (distance should increase when
rinsing pin-striping or other sensitive
surfaces). Always clean from top to bottom
and from left to right. For best results,
wipe surface dry with a chamois or
soft dry cloth.
Caution: Do not use Rotating spray wand
on vehicles as it may cause damage.
9
CLEANING TIPS
– continued
Barbecue Grills, Outdoor
Power Equipment &
Gardening Tools
(with or without detergent)
Pre-rinse cleaning surface with fresh water.
If using Cub Cadet All Purpose Cleaner or
Degreaser, place detergent suction tube
directly into cleaning solution and apply
detergent at low pressure. Allow Cub Cadet
detergent to remain on surface 1-3 minutes.
Do not allow detergent to dry on surface.
Rinse at high pressure keeping the spray
nozzle approximately 3-6 inches from the
cleaning surface. For removing extremely
stubborn dirt, it may be necessary to move
the spray nozzle even closer to the surface
for greater dirt cutting action. To remove
caked on mud from garbage cans, lawn
mower blades, wheelbarrows or other
non-sensitive metal surfaces, you may
want to use the Cub Cadet Dirtblaster
®
Wand.
Caution: Do not use Dirtblaster®wand on
cloth, plastic or other sensitive surfaces
as it may cause damage.
Patio & Lawn Furniture
(with or without detergent)
Pre-rinse furniture and surrounding area with
fresh water. If using Cub Cadet All Purpose
Cleaner, place detergent suction tube directly into cleaning solution and apply to surface
at low pressure. Allow Cub Cadet All
Purpose Cleaner to remain on surface 1-3
minutes. Do not allow detergent to dry on
surface.
If needed, use special Wash Brush
Attachment to remove stubborn dirt. Rinse
at high pressure in a sweeping motion keeping the spray nozzle approximately 3-6 inches from the cleaning surface. For best
results, clean from top to bottom and from
left to right. Caution: Do not use
Dirtblaster®wand on patio or lawn furniture as it may cause damage.
Recommendations
• Before cleaning any surface an inconspicuous area should be cleaned to test spray
pattern and distance for maximum cleaning results.
• If painted surfaces are pealing or chipping,
use extreme caution as pressure washer
may remove the loose paint from the
surface.
10
TROUBLESHOOTING
Disconnect the machine from the power source before making any repair.
Symptom Cause Solution
Motor will not start.
Unit does not reach
high pressure.
Output pressure
varies high and low.
Extension cord is too long.
Extension cord is
not proper gauge.
Extension cord is damaged.
Replace extension cord with either
a 25 ft. 12/2 gauge cord or a 50 ft. 10/2
gauge cord.
Electrical outlet does not supply
adequate power.
Try a different outlet.
Ground Fault Circuit Interrupter
(GFCI) tripped.
Reset breaker (power supply)
or GFCI.
Diameter of garden hose
is too small.
Replace with a 3/4 inch
garden hose.
Water supply is restricted.
Check garden hose for kinks,
leaks and blockage.
Not enough inlet water supply. Open water source full force.
Water inlet filter is clogged. Remove filter and rinse out
in warm water.
Not enough inlet water supply. Turn water on full force. Check garden
hose for kinks, leaks or blockage.
Pump is sucking air. Check that hoses and fittings are air tight.
Turn off machine and purge pump by
squeezing trigger gun until a steady flow
of water emerges through the nozzle.
Water inlet filter is clogged.
Remove filter and rinse out
in warm water.
Discharge nozzle
is obstructed.
Blow out or remove debris
with a fine needle.
Calcified gun, hose
or spray wand.
Run distilled vinegar through
detergent suction tube.
On/Off switch is in the “OFF”
(O) position.
Turn switch to the “ON” (I) position
Power cord is not plugged in.
Plug in power cord.
Spray wand is in low
pressure position.
Turn spray wand to high
pressure position.
Dealer Referral Line
1-877-835-7841
or visit our website: www.cubcadet.com
11
TROUBLESHOOTING
– continued
Symptom Cause Solution
No detergent.
Garden hose
connection leaks.
Pump is noisy.
Water leaks from
pump (up to 10
drops per minute
is permissible).
Oil Drip.
Detergent is too thick. Dilute detergent, for best results
use Cub Cadet detergent.
Filter on detergent suction
tube is clogged.
Run warm water through filter
to remove debris.
Damaged or clogged
detergent suction tube.
Remove obstruction or
replace detergent suction tube.
Spray wand is in
high pressure position.
Turn spray wand tip to
low pressure position.
Discharge nozzle
is obstructed.
Blow out or remove debris
with fine needle.
Loose fittings. Tighten fittings.
Missing/worn rubber washer. Insert new washer.
Spray wand extension
not properly attached.
Broken o-ring or
plastic insert.
Check that hoses and fittings are
air tight. Turn off machine and purge
pump by squeezing trigger gun until
a steady flow of water emerges
through the nozzle.
Loose fittings. Check that all fittings are tight.
Call service center.
Water seals are
damaged or worn.
Call Cub Cadet customer service
hotline and order repair kit
(part no. 2.883-111.0).
Pump is sucking air.
Oil seals are damaged
or worn.
Call service center.
Spray wand
or spray wand
extension leaks.
Spray wand not
properly attached.
Insert the spray wand into the spray
wand extension. Carefully press in
against the spring tension and twist
into the locked position.
Slide the spray wand extension into the
gun. Turn the wand collar clockwise onto
the gun threads until tight.
Detergent suction tube not
properly connected to the
machine.
Check connection.
If you encounter any additional
difficulties not listed, please call
our service center for help.
Cub Cadet Customer Support USA
Reservoir is empty. Add more detergent.
Dealer Referral Line
1-877-835-7841
or visit our website: www.cubcadet.com
MANUFACTURER’S LIMITED WARRANTY
for PRESSURE WASHER S
(RESIDENTIAL LINE)
The limited warranty set forth below is given by CUB CADET with respect to new
merchandise purchased and used in the United States, its possessions and territories.
CUB CADET warrants this product against defects in material and workmanship for a period
of one (1) year
its option, repair or replace
workmanship. This limited warranty shall only apply if this product has been operated and
maintained in accordance with the Operators Manual furnished with the product, and has not
been subject to misuse, abuse, neglect, accident, improper maintenance, improper storage or
handling, freezing, use of improper chemicals, alterations, vandalism, theft, fire, water, or
damage because of other peril or natural disaster. Damage resulting from the installation or
use of any accessory or attachment not approved by Cub Cadet for use with the product(s)
covered by this manual will void your warranty as to any resulting damages. The following
parts and accessories are subject to separate terms as follows: Limited Warranty: 90-day free
replacement for defects in materials and/or workmanship on hoses, hose reels, spray wands,
brushes, nozzles and/or similar approve d accessorie s.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF OF
PURCHASE, THROUGH YOUR LOCAL AUTHORIZED CUB CADET or CUB CADET
COMMERCIAL DEALER. To locat e the dealer in your area, please check for a listing in
the Yellow Pages or contact CUB CADET by calling 877-835-7841 or writing to PO BOX
368023, Cleveland, Ohio 44136-9723.
This limited warranty does not provide coverage in the following cases:
(a) Routine maintenance items such as lubricants, filters, tune-ups, or adjustments.
(b) Equipment setup, normal wear parts or components.
(c) CUB CADET does not extend any warranty for p roducts sold or expor ted outside
No implied warranty, including any implied warranty of merchantability or fitness for a
particular purpose, applies after the applicable period of express written warranty
above. No other express warranty or guaranty, whether written or oral, except as
mentioned above, given by any person or entity, including the dealer with respect to any
product shall bind CUB CADET. During the period of the Warranty, the exclusive remedy
is repair or replacement of the product as set forth above . (Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)
The provisions as set forth in this Warranty provide the sole and exclusive remedy
arising for the sale. CUB CADET shall not be liable for incidental or consequential loss
or damages including, without limitation, to any claim for loss of profits, loss of
savings or revenue, loss of the use of the equipment or any associated equipment.,
facilities or service, downtime, the claims or costs of third parties including customers,
and injury to property, and further including expenses incurred for substitute or
replacement property care services, for transportation or for related expenses, or for
rental expenses to temporarily replace a warranted product. (Some stat es do not allow
the exclusion or limita ti on of incidental or consequ ent ial damages, so the above excl usion may
not apply to you.)
In no event shall re covery of an y kind be great er than the amo unt of the purcha se price of
the product sold . Alteration of the safety features of the product shall void t his warranty. You
assume the risk and liability for loss, da mage, or injury to you and your property and/or to
others and their property arising out of use or misuse or inability to use this product.
This limited warranty shall not extend to anyone other than the original purchaser or original lessee,
or the person for whom it was purchased as a gift.
HOW STATE LAW RELATES to this WARRANTY: This limited warranty gives you
specific legal rights, and you may also have other rights which vary from state to state.
for residential users, commencing on the date of original purchase and will, at
, free of charge, any part found to be defective in material or
of the United States, its possessions, and territories.
Dealer Referral Line: 1-877-835-7841
or visit our website: www.cubcadet.com
To locate your nearest dealer
Loading...