Ctx VL510 User Manual

VL510 User’s Manual

User’s Manual

VL510

1

VL510 User’s Manual

Table of Contents

1. Safety Instructions 3

2. Recommendation for Optimum Performance 7

3. Introduction 8

4. Installation 9

5. Controls and Adjustments 12

6. Trouble Shooting 15

7. Energy Declaration 17

8. Specification 18

9. Reference Information 19

2

Safety Instructions

FCC Statement

T

his equipment has been tested to comply with the limits for a class B digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

VL510 User’s Manual

encouraged to try to correct the interference by one or more of the following

measures:

Warning:

If a shielded-type power cord is supplied with this monitor, it is required in

order to meet FCC emission limits and to prevent interference with nearby

radio and television reception. Only shielded cables should be used to

connect I/O devices to this equipment. You are cautioned that changes or

modifications not expressly approved by the party responsible for compliance

could void your authority to operate the equipment.

• Relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

3

VL510 User’s Manual

CE Statement

T

his device complies with the requirements of EMC (Electromagnetic

Compatibility), and with Low Voltage directive.

Safety Precautions

1. Please read carefully all of these instructions below and keep the manual for

later use.

2. Please install the swivel base below this product before using it.

3. The voltage ratings and the rated frequency are on the overlay centered at

rear side of this product. Do not connect with any other sources of voltage or

frequency, and please follow all warnings and instructions marked on the

product.

4. Unplug this product from the wall outlet before cleaning and use a damp

cloth to clean it. Do not use liquid cleaners or aerosol cleaners.

5. Do not expose this product to rain or moisture.

6. Do not place this product on an unstable cart, stand, or table. The product

may fall, causing serious damage to the product.

7. Do not block or cover ventilating openings with cloth or other material.

Neither should this product be placed near or over a radiator or a heat

register, nor should the product be placed in a built-in installation unless

proper ventilation is provided.

8. This product is equipped with a 3-wire grounding model plug. This plug will

only fit into a grounding-model power outlet. This is a safety feature. If you

are unable to insert the plug into the outlet, contact your electrician to

replace your obsolete outlet. Do not defeat the safety purpose of the

grounding-model plug. Choose a Tandem Blade attachment plug

configuration power cord for 230V AC input.

4

VL510 User’s Manual

Due to the safety requirements of different areas, please select a

suitable power cord according to the following rules, in addition to the

electric rating:

A. Northern America area: Please select a UL listed and CSA

certified power cord.

B. Germany: Please select a VDE certified power cord.

C. Nordic countries: Please select a power cord certified by

SEMKO, NEMKO, DEMKO or FIMKO.

D. The other areas: Please select a power cord suitable to the

local power system and power outlet.

Usually, when this product is sold, the manufacturer provides a

suitable power cord. However, this product is sometimes resold or

transported to another area, with different power system and safety

requirements. Please pay attention to the selection of a suitable

power cord. The plug on the power cord is intended to serve as the

disconnect device, the socket-outlet shall be installed near the

equipment and shall be easily accessible.

9. Do not allow anything to rest on the power cord. Do not locate this product

where persons can walk on the cord.

10. Never push objects of any kind into this product through cabinet slots as they

may touch dangerous voltage points or short out parts that could result in the

risk of fire or electric shock. Never spill liquid of any kind on the product.

11. Do not attempt to service this product yourself, as opening or removing

covers may expose you to dangerous voltage points or other risks. Refer all

servicing to service personnel.

12. Unplug this product from the wall outlet and refer servicing to qualified

service personnel under the following conditions.

5

VL510 User’s Manual

A. When the power cord or plug is damaged or frayed.

B. If liquid has been spilled into the product.

C. If when the operating instructions are followed, the product has

been exposed to rain or water.

D. If the product does not operate normally, adjust only those

controls that are covered by the operating instructions since

improper adjustment of other controls may result in damage

and will often require extensive work by a qualified technician

to restore the product to normal operation.

E. If the product has been dropped or the cabinet has been

damaged.

F. If the product exhibits a distinct change in performance,

indicating a need for service.

Notice : Actual safety specifications please refer to the label on the back

of monitor.

6