The CTX SERVICE MANUAL is published by Chuntex Electronic Co., Ltd
All rights reserved. No part of this manual may be used, copied, reproduced, or transmitted in any form or by
any means for any purpose without the express written permission of the publisher.
The publisher has been trying its best to make this publication perfect, and in this manner takes no
responsibility for the use of any of the materials or methods described in this manual, or for the products
thereof. Neither will the publisher be responsible for any damages caused by misuse or misquotation.
Service Manual
S720G
Information in this manual is subject to change by the publisher without any notice in advance.
CTX is a registered trademark of Chuntex Electronic Co., Ltd.
-2-
Page 4
C
y
)
T
X
C
T
X
C
T
X
1. SCOPE
Feature Description
10 OSD (on screen display) MENU operation
10.1 Brightness adjustment
10.2 Contrast adjustment
10.3 Auto tune function (VGA)
10.4 Color selection
10.5 Image adjustment
10.6 Position adjustment
10.7 Language selection
10.8 Reset function
10.9
10.10 1W * 2 Audio function inside the monitor
11 Volume adjust by OSD
12 OSD information of input status
2. INPUT REQUIREMENTS
1 Universal input AC/DC power supply inside the monitor
2 Analog RGB interface (VGA ) 30~80KHz, 59~75Hz, 135MHz
3
4 17” SXGA 1280*1024, TFT LCD panel
5
6
7 Green/Amber LED indicator for power on/power saving
8 Plug & play support with DDC2B protocol installed.
9 Power saving mode compliant with Energy Star
Digital Visual interface(DVI-D) TMDS 1 Channel 165 MHz
Function ke
Direct Acess function keys : △ for
Source selection(DVI/VGA)
2.1 Input Power
2.1.1. Power Source
2.1.2. Power Consumption
2.1.3. AC Line Drop Out
2.1.4. AC Wave Distortion
2.1.5. In-rush Current
2.1.6. Power Cord
This specification defines the design and performance requirements for the 17” SXGA TFT
LCD display monitor.S720G
s * 5 : Power On/Off, ESC, △(up), ▽(down), (enter
contrast function, ▽ for brightness function , ESC
100 ~ 240 Vac, + -10%, 50/60 Hz
Normal operating mode
Audio function is operating at max output: ≦ 39W
w/o audio function : ≦ 35W
Power saving mode
Audio function is operating at max output: ≦ 7W
w/o audio function : ≦ 2W
Power switch off : ≦ 1.5W
Picture must not disappear while AC 100 V input drop out(10ms, 100%)
10% max. permitted
50 A max at 240 Vac cold start
Detachable, 3P with ground type.
Service Manual
S720G
-3-
Page 5
C
T
X
C
T
X
C
T
X
2.2 Display Input
2.2.1. Analog Input RGB Video
2.2.1.1 Sync Signal
Analog Input Connection a. Detachable Mini D-sub 15 pin male in two ends signal
b. A female Mini D-sub 15 pin base.
Pin 1 Red
2.2.2 Digital Input
Input Interface DVI-D V.1 TMDS 165MHz 1-Channel
Digital Input connection a. Captive cable (length 1.5M) in LCD monitor end ,
DVI-D male
connector in another end.
b. Cable pin assignment
DVI-D 1-Channel Pin Assignment
Analogue, 0.0 to 0.7 V peak to peak
Separate RGB
Input impedance 75 Ohm
Positive polarity
Separate horizontal & vertical sync (3.3V & 5V)
Low level 0.8 V maximum
High level 2.0 V minimum
Positive or negative polarity
cable , length 1.8M.
Pin 2 Green
Pin 3 Blue
Pin 4 No Connection
Pin 5 Ground
Pin 6 R Return
Pin 7 G Return
Pin 8 B Return
V. Sync. Polarity + - - - + + +
O ms ( Period ) 16.683 13.735 13.333 16.579 13.853 13.333
P ms ( Pulse Width ) 0.064 0.079 0.080 0.106 0.125 0.064
3.1 LCD Panel
3.2 Modes and Timing Comparability
Display Format IBM VGA VESA VESA VESA VESA VESA
3.1.1. Type 17” diagonal, SXGA resolution, color TFT-LCD
3.1.2. Pixel structure
3.1.3. Gray scale 16 million colors.
3.1.4. Surface treatment 3H hard coating ,anti-static,anti-glare
3.1.5. Backlight
3.1.6 Pixel Faults
Pixel Faults type
Type
Bright Pixels (Note 1)
Type
Dark Pixels (Note 2)
Type
Fault Pixels / Sub-Pixels(Note 3)
Type Cluster of type1 or type 2 faults(Note
Type
Cluster of type3 faults (Note4)
Type
Total Pixel Faults
Note 1 : Bright pixels in full black pattern.
Note 2 : Dark pixels in full white pattern
Note 3 : fault Pixel / Sub-Pixel : The pixel or sub-pixel is abnormal but not bright/dark pixel.
Note 4 : Fault Cluster : Two or more Pixels/Sub-pixels with faults within 5 * 5 block of pixels.
31.469 37.861 37.5 37.879 48.077 46.875
31.778 26.413 26.667 26.4 20.8 21.333
3.813 1.270 2.032 3.2 2.4 1.616
1.907 4.063 3.810 2.2 1.28 3.232
25.422 20.317 20.317 20.0 16.0 16.162
0.636 0.763 0.508 1.00 1.12 0.323
-5-
Project
Model
R/G/B sub-pixels in vertical stripes
1280 x 1024 array matrix
a-Si TFT active matrix
Integral CCFL, type to support field replacement.
Life time 30000 hours @ 25C, 50% of initial value.
V. Sync. Polarity - - + +
O ms ( Period ) 16.666 14.272 13.238 13.333
P ms ( Pulse Width ) 0.124 0.106 0.050 0.044
Q ms ( Back Porch ) 0.6 0.513 0.466 0.474
R ms ( Active Area ) 15.88 13.599 12.795 12.8
S ms ( Front Porch ) 0.062 0.054 0.017 0.015
*3.6.4.6 Key lock function Push” “ for 10 sec while the screen has no any OSD showing to
)
)
)
)
The switch control scaler power down and turn off panel.
The LED color shall indicate power status as shown in paragraph
3.7
ESC ,▽ , △ ,
See Table 2. S730G/S720G OSD Control Map
Press “△ ” to pop up ;then press “△ ” or “▽ ” to adjust Contrast up
or down.
Press “▽ ” to pop up ;then press “△ ” or “▽ ” to adjust Brightness
up or down.
Press “Esc” directly to disable speakers, while speakers in normal
state.
Press “Esc” directly to enable speakers, while speakers in audio
mute state.
“Esc” key is for Mute On and Off function
“△ ” key is for increasing volume function.
“▽ ” key is for decreasing volume function.
“ESC” key is enable or disable audio mute.
Service Manual
S720G
Setup “Key lock” functions enable or disable.
Table 2 S720G/S730G OSD Control Map
Level 1 Level 2 Level 3 Level 4
Direct Adj. Brightness
Direct Adj. Contrast
Direct Adj. Audio Mute
Main Menu
Volume Adjustment Scale
*Auto Tune *Adjustment Scale
Color
Image
9300∘ K
6500∘ K
User R/G/B select Adjustment Scale
*Clock *Adjustment Scale
*Phase *Adjustment Scale
Smooth On/Off
*
-8-
*H-Position *Adjustment Scale
Page 10
C
T
X
C
T
X
C
T
X
*V-Position *Adjustment Scale
*Center *Adjustment Scale
Service Manual
S720G
Language
Reset Yes/No
Source DVI/VGA
*Function is disable in DVI mode.
OSD Position
English (select)
Deatsch (select)
French (select)
Spanish (select)
Italiano (select)
中文 (option)
H-Position Adjustment Scale
V-Position Adjustment Scale
Center Adjustment Scale
3.6.5 Accessory OSD Indications
Signal out of range An input signal which is outside the range defined in
No Signal Input , Input Source
“auto detecting” and power down.
Section 3.4 shall cause the monitor to display a message
Signal Out of Range.
When the signal cable is not plugged into PC or when the
horizontal or vertical sync are absent and when the
monitor is turned on. After 5 sec isn’t to detect H or V Sync
then show “No Signal Input” for 3 seconds then show”Auto
detecting” message on the OSD for 2seconds,( if first turn
on the monitor that will show it around 27 seconds.), and
then show ” Power down” message on screen 2 sec.And
then the monitor shall go to power saving status.
-9-
Page 11
C
T
X
C
T
X
C
3.7 Power Management
T
X
This monitor will meet the low power specification, Including USA governmental requirements
For Energy Star, the NUTEK standard and the VESA DPMS standard which detected the Hori. /Vert.
Sync signal from host CPU.
A dual color (green/amber) LED is located on the front bezel to indicate the power management states.
Status
Sync. Video
Active Active 39W max. On - Green
consumption
Power
Power
management
Service Manual
S720G
Picture Recovery time LED Color
No Sync. Blanked
Note. 1 : Audio function is operating at no signal input.
≦ 2W
(Note.1)
Power saving
≦ 3 sec
Amber
Once “Esc” or “△ ” or “▽ ” key initiates under power saving condition, the audio
function can be waked up and the power consumption can not be the above definition.