Page 1
PR960F User’s Manual
User’s Manual
PR960F
1
Page 2
PR960F User’s Manual
Table of Contents
1. Safety Instructions 3
2. Recommendation for Optimum Performance 5
3. Introduction 6
4. Installation 7
5. Controls and Adjustments 10
6. Trouble Shooting 15
7. Energy Declaration 19
8. Specification 20
9. Reference Information 22
2
Page 3
PR960F User’s Manual
Safety Instructions
FCC Statement
This equipment has been tested to comply with the limits for a class B digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning:
If a shielded-type power cord is supplied with this monitor, it is required in order to meet FCC
emission limits and to prevent interference with nearby radio and television reception. Only
shielded cables should be used to connect I/O devices to this equipment. You are cautioned
that changes or modifications not expressly approved by the party responsible for compliance
could void your authority to operate the equipment.
CE Statement
This device complies with the requirements of EMC (Electromagnetic Compatibility), and with
Low Voltage directive.
Safety Precautions
Always observe these important safety instructions:
1. Allow adequate ventilation around the monitor so that heat can be dissipated properly. Do
not block or cover ventilated openings. Do not place the monitor in an enclosure that will
obstruct the free flow of air.
3
Page 4
PR960F User’s Manual
2. Do not place the monitor or other heavy objects on the power cord. A damaged power cord
can cause fires or electrical shock.
3. Keep the monitor away from high-capacity transformers, electric motors and other strong
magnetic fields.
4. Do not connect to any voltage or frequency beyond the range specified on the back of the
monitor. Please follow all warnings and instructions marked on the product.
5. Unplug the monitor from the electrical power source before cleaning any part of the monitor.
Do not use liquids, sprays or aerosol cleaners. Clean the surface of the screen with a lint-free,
non-abrasive cloth and a non-alcohol, neutral and non-abrasive cleaning solution or glass
cleaner. Use a slightly dampened cloth to clean the exterior of the plastic cabinet.
6. This product is equipped with a 3-wire grounding-type plug, an important safety feature. This
plug will only fit into a grounding-type power outlet. If a grounding-type power outlet is not
available, have one installed by a qualified electrician. Do not cut off the grounding pin in order
to make the plug fit into an inappropriate power outlet.
7. For 230VAC operation, a power cord with tandem blade plug is required. Select your power
cord in accordance with the safety regulations of your country. For example
North America UL listed and CSA certified
Germany VDE certified
Nordic Countries SEMKO, NEMKO, DEMKO, or FIMKO certified
8. Do not attempt to service this product yourself! Opening or removing covers may expose
you to dangerous voltage points or other risks. Refer all servicing to qualified service
personnel.
9. The plug on the power cord is intended to serve as the disconnect device. The socket-outlet
should be installed near the equipment and should be easily accessible.
Notice : Actual safety specifications please refer to the label on the back of monitor.
4
Page 5
PR960F User’s Manual
Recommendation for Optimum Performance
When setting up and using the monitor, pay special attention to the following for optimum
performance:
• Do not use your monitor against a bright background or where sunlight or
other light sources will shine directly on the screen.
• The monitor should be placed just below eye level (10° - 15° for optimum
viewing).
• Set the monitor's brightness to match the ambient room light.
• For optimum focus, the contrast control should not be set to the maximum
level unless the input signal level is extremely low. Also, the brightness control
should be set to a point where the overall background area just begins to
disappear.
• Allow adequate ventilation around the monitor so that the heat from the
monitor can properly dissipate.
CAUTION
• Neither the monitor itself, nor any other heavy objects, should rest on the
power cord. Damage to the power cord can cause fire or electrical shock.
• Keep the monitor away from high-capacity transformers, electrical motors, or
other strong magnetic fields.
• Your monitor should not be used in damp, dusty, or dirty areas.
• Handle your monitor with care when transporting it.
• Do not scrap or knock the surface of CRT with a pen, a screwdriver and so on.
• Clean the CRT surface with a lint-free, nonabrasive, soft cloth, and should not
use the solution or glass cleaner containing corpuscles like an abrasive,
alcohol and an alkaline solution.
5
Page 6
PR960F User’s Manual
Introduction
The monitor is a multiple frequency high-resolution color monitor for IBM compatible PC's or
Macintosh and workstation systems. The monitor is equipped with microprocessor based
intelligence and multiple frequency scanning capability, allowing it to provide maximum
compatibility for various system platforms.
The monitor uses the latest screen technology including a 0.24mm SONY FD Trinitron® CRT
to display crisp text and vivid color graphics. The full-function digital control and On-Screen
Display (OSD) system provides easy adjustment of image geometry and color settings for
different display modes with the precision of a fixed frequency monitor.
The design of the monitor is also ergonomically concerned. In addition to the friendly controls
and user comfort features, the emission level of the electric and magnetic field is kept low to
meet the Swedish MPR II and TCO standards.
The monitor is also equipped with energy saving functions; it is compatible with the VESA
power saving standards.
Furthermore, the monitor is built-in the USB (Universal Series Bus) hub. Please refer to the
"USB SetUp Guide
" for the implementation of USB hub.
6
Page 7
PR960F User’s Manual
Installation
Unpacking
The following lists all of the items included in the monitor package box. Please save the
original box and packing materials for future transportation or shipment of the monitor.
1. Color monitor with tilt/swivel base
2. Signal cable
3. Power cord
4. USB Cable
5. User's Guide / Driver CD
7
Page 8
PR960F User’s Manual
System Setup
1. Turn off the system and all attached peripherals.
2. Carefully set the monitor upside down.
Remove the Tilt/Swivel Base
1. Squeeze and hold the latches.
2. Pull the tilt/swivel base to the rear of the monitor and lift to remove the base.
8
Page 9
PR960F User’s Manual
Installing the Tilt/Swivel Base
1. Align the base with the slots on the bottom of the monitor and insert the tilt/swivel base into
the slots.
2. Push the tilt/swivel base firmly toward the front of the monitor until the latches click into the
locked position.
9
Page 10
PR960F User’s Manual
Controls and Adjustments
Once you have installed the monitor for your system, please read the instructions of this
section which give you some guidelines on how to use the monitor more efficiently. It leads you
through the various functions of the user controls and explains how to adjust the monitor to
your personal preference.
Front Panel Controls
1. Power Switch
To turn the monitor on or off.
2. Power LED Indicator
As long as the monitor is powered, this indicator is lit. In normal operation, it lights green. While
in stand-by mode, the indicator lights yellowish-green, while in off mode it is amber.
3. Adjust Keys
To adjust the parameter of the selected function.
To adjust the contrast level or brightness of the screen.
4. Menu Key
To display and select the "General", "Picture", "Geometry", "Color", "Advance", "Property",
"Signal" functions.
10
Page 11
PR960F User’s Manual
How to Make On-Screen Display (OSD) Adjustments
On-Screen Displays are called up from the front panel controls as noted above. Adjustments
are made with "+ " , "-" , "
Power Saving Note:
This monitor is equipped with an automatic power-saving circuitry design that will work with
any computer, which meets the VESA DPMS standard. It meets the ENERGY STAR low
" and " " control switches.
power state definition.
OSD (On-Screen Display) Controls
(1) Press " " or " " to open the On-Screen menu function. Seven adjustment functions will
appear on the On-Screen menu. Press "
below.
A. General
a. Press "
b. Press "+" or "-" to preferred picture.
" to select Brightness or Contrast.
" key to scroll selections from top-down sequence as
B. Picture
a. Press "
b. Press "+" or "-" to preferred picture.
" to select Vertical and Horizontal position, Vertical and Horizontal size.
11
Page 12
C. Geometry
PR960F User’s Manual
a. Press "
b. Press "+" or "-" to preferred picture.
" to select Side-pin, Balance, Keystone, Parallel and Rotate.
D. Color
a. Press "
b. In User item, presses "+" to confirm action color adjustment.
c. Press "
d. Press "+" or "-" increase or decrease density.
" to select various white color temperature standards.
" to select Red, Green and Blue.
E. Advance
a. Press "
b. Press "+" to proceed.
c. Press "+" or "-" to gain preferred picture.
" to select Moire, Converge, Purity and Degauss.
E-1. Moire
a. At Moire item, press "+" to proceed.
b. Press "+" or "-" to gain preferred picture.
12
Page 13
E-2. Converage
a. In Converge, press "+" to proceed.
PR960F User’s Manual
b. Press "
c. Press "+" or "-" to gain preferred picture.
" to select Horizontal or Vertical adjust.
E-3. Purity
a. In Purity, press "+" to Proceed.
b. Press "
and bottom rows, and, the four corners of the screen.
c. Press "+" or "-" to gain preferred color uniformity.
Caution:
" to select the function you want to adjust. Color purity can be adjusted in the top
1. If moire reduction is overdone, picture quality, i.e. focus and vertical line stability will both be
effected.
2. Proper adjustment is recommended for not effecting picture performance.
F. Property
Press "
" to select Status, Recall or Language sub-menu.
F-1. Status
The status shows the current input signal information such as resolution Horizontal frequency
and Vertical frequency.
13
Page 14
F-2. Recall
PR960F User’s Manual
a. Press "
b. Press "+" to proceed.
c. "+" confirms action, "-" cancels action.
" to select picture, converge, or purity.
F-3. Language
Press "+" or "-" to select the Language for OSD only.
G. Signal
Press "+" or "-" to select the input Signal from D-15 or BNC connector.
(2) Contrast
When OSD is off, "+" or "-" increase or decrease contrast.
14
Page 15
Trouble Shooting
Notify your supervisor or contact your service personal when:
• Power cords are frayed or damaged.
• Liquid is spilled into the monitor.
• The monitor does not operate normally when operating instructions are
PR960F User’s Manual
observed.
• The monitor has been dropped or the cabinet has been damaged.
Review this list of trouble-shooting tips before contacting an authorized service center.
Problem What to do
Power Indicator (LED) is not lit.
No Picture.
Make sure Power control is in the ON
position.
Check the power cable. It must be plugged in
completely.
If the Power Indicator is amber-colored your
computer has sent the monitor into its Power
Save mode (See "Energy Declaration.")
No Signal Input.
The video card may not be seated properly.
Make sure it is fully seated in its slot.
Make sure the signal cable is connected
securely to the video card or computer.
Enable "Power Save" function.
15
Page 16
PR960F User’s Manual
Signal Out of range.
Display image is not centered or
is too small or too large.
Image is scrolling or is unstable
Picture is fuzzy or color looks
blotchy.
Readjust the signal based on spec.
Reference "Scan Frequency".
Refer to "Controls & Adjustments." You need
to adjust "Size" and "Position" of the image.
Make sure the signal cable is connected
securely to the video card or computer.
Adjust Contrast and Brightness controls.
On all Models select the Degauss function in
Picture bounces or a wave
pattern is present.
Edges of display are curved
inward or outward.
the OSD control menu.
(CAUTION: Allow a minimum of 20 minutes
to elapse before depressing Degauss button
again when not switching between modes.
DO NOT HOLD THE BUTTON DOWN
CONTINUOUSLY.)
Move devices that might be causing
electrical interference away from the monitor.
(See "FCC Information.")
Refer to "Controls and Adjustments." You
need to adjust the "Side Pincushion."
16
Page 17
PR960F User’s Manual
No Plug & Play.
Verify that the host system is Plug & Play
compatible.
Check to see if Windows is installed, and the
software key for the Data Display Channel
(DDC) function is enabled.
Determine if original manufacturer's
detachable signal cable is being used
(D-Sub-15 pin only). BNC cable does not
carry SCL (Signal Clock) and SDA (Signal
Data) signals and therefore does not support
Plug & Play function.
Our PR960F is build-in FD Trinitron® CRT. This CRT is sensitive to shocks and vibrations that
may occur during transportation. Following are some adjustment tips when below mentioned
symptoms occur.
Two horizontal lines are visible
on the screen
Symptom Tip
This is normal characteristic of FD
Trinitron® CRT.
These are damper wires, which are
attached to the aperture grille and are
designed to dampen and prevent shock
and vibrate to the aperture grille.
17
Page 18
PR960F User’s Manual
Black fine vertical lines are
visible on the screen. Shock and
vibration may cause the
aperture grille misaligned, which
results few fine black vertical
lines across the screen
Degaussing the screen.
Tap lightly (do not hit) the side of the
monitor.
If above mentioned remedies do not work,
please do the following:
1.Display full white window or wallpaper
background over the area where the black
lines appears.
2.Set Contrast and Brightness to the
maximum, wait for a moment until the
problem is corrected. You may try to tap
lightly the side of the monitor.
18
Page 19
PR960F User’s Manual
Energy Declaration
This monitor is equipped with a function for saving energy, which supports the VESA Display
Power Management Signaling (DPMS) standard. This means that the monitor must be
connected to a computer, which also supports the VESA DPMS standard to fulfill the
requirements of the NUTEK specification 803299/94/96. The time settings for switching to a
power saving mode are adjusted from the system unit by software. From the first indication of
inactivity to power saving position A2 the total time must not be set to more than 70 minutes.
1. VESA Power-Management Proposal
H. sync V. sync Video State
Off On Blank Stand-by
On Off Blank Suspend
Off Off Blank Off
2. Power Consumption (120/230 Vac)
NUTEK VESA state LED indicator
Normal operation
Power Saving
Position A1
Power Saving
Position A2
* Recovery Time < 3 Sec.
On Green < 125W
Suspend Amber < 15W
Off Amber < 8W
Power
Consumption
19
Page 20
Specification
PR960F User’s Manual
Color Picture Tube
AG Pitch
Input Signal
19" (18" viewable screen size) diagonal
measurement, 90 degree deflection, SONY FD
Trinitron® CRT, anti-glare, anti-reflection,
anti-static, medium short persistence phosphor.
0.24 mm, (center)
Video: 0.7 Vp-p/75 ohm, analog positive
Sync: Separate
Sync.:
TTL Level
Horizontal
Sync.:
Vertical
Sync.:
positive/negative
positive/negative
Scan Frequency
Max. Resolution
Display Colors
Pixel Rate
Plug & Play
Composite
Sync.:
Horizontal: 30 to 110 kHz automatically
Vertical: 50 to 160 Hz automatically
1600 x 1200 pixel, non-interlaced
Analog input, unlimited colors
232 MHz
DDC 1 / DDC 2B
TTL Level,
positive/negative on
green
video(0.3Vp-p
Negative)
20
Page 21
PR960F User’s Manual
USB
Power Supply
Power Consumption
Dimensions
Weight
Environment Consideration
Downstream port x 4, Per downstream port
support current 500mA(Max.)
100-120 VAC/200-240 VAC, 50/60 Hz
(automatically)
125W max.
460(W) x 469(H) x 485(D) mm
28.5 kgs(G.W.), 26.5 kgs(N.W.)
Operating Temperature: 0°C to 35°C
Humidity: 20% to 80%
Storage Temperature: 0°C to 60°C
Humidity: 10% to 90%
Note: Specifications are subject to change without notice.
21
Page 22
PR960F User’s Manual
Reference Information
This color monitor supports multiple operating platforms such as IBM compatible and
Macintosh family computers. This section provides you with detailed information on pin
assignment of the D-Sub connector and the preset timing chart of the prevailing video
standards.
Connector Pin Assignments
Male Mini D-15 Connector
Signal 15 Pin Mini D-Sub
Red Video 1
Green Video 2
Blue Video 3
Horizontal Sync 13
Vertical Sync 14
Ground 4,5,6,7,8,10,11
No Connection 9
SDA (DDC) 12
SCL (DDC) 15
22
Page 23
Pin Assignments of the BNC and USB Connectors
Back
Side
PR960F User’s Manual
USB SetUp Guide
This monitor is equipped with 4 downstream ports marked "1" ,"2","3" and "4" respectively,
one upstream port marked "TO HOST" (on its back or swivel base) and one USB cable used to
connect the monitor to the USB port of your host PC.
With the benefit of plug-and-play, you can attach any USB device to any one of the
downstream ports of your monitor, even while your PC and monitor are working.
Warning: Every downstream port is capable of bearing a maximum current of 500mA. To
avoid causing damage to your monitor please check the power consumption of the all USB
devices before connecting them to your monitor.
Monitor is equipped with Plug & Play capability (VESA DDC 1/2B). To
utilize this capability, your graphic card and hosting system have to be
Plug & Play compatible as well. When properly plugged(Plug), the graphic
card and hosting system will automatically (Play) identify, configure, and
most importantly, optimize this monitor's capabilities, providing you with simple and easy
installation and setup.
23
Page 24
PR960F User’s Manual
Preset Timing Chart
Note: This monitor is equipped with a microprocessor which allows the user to set his own
preferred mode(s) beyond those standard mode listed below.
To reduce visual tiredness and eyestrain, it is recommended to choose the highest refresh
modes available.
Resolution Format
640x480@60Hz VGA 31.5 60
640x480@85Hz VESA 43.3 85
640x480@120Hz
720x400@70Hz VGA 31.5 70
800x600@85Hz VESA 53.7 85
800x600@120Hz
Horizontal
Frequency (KHz)
Refresh Rate (Hz)
63.5 120
76 120
1024x768@75Hz VESA 60 75
1024x768@85Hz VESA 68.7 85
1024x768@100Hz
1280x1024@75Hz VESA 80 75
1280x1024@85Hz VESA 91.1 85
1600x1200@75Hz VESA 93.6 75
1600x1200@85Hz VESA 107 85
80.5 100
24
Loading...