CTX P772 User Manual

User's Manual

P772 LCD Monitor

Federal Communications Commission (F.C.C.) Statement

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Relocate the receiving antenna.

• Increase the distance between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use only shielded cables or connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

This publication including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual nor any of the material contained herein may be reproduced without the express written consent of the manufacturer.

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents here of merchantability or fitness for any particular purpose. Further, the manufacturer reserves the right to revise this publication ad to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS, and Windows are registered trademarks of Microsoft Corp. Intel, Pentium, and Pentium II are register trademarks of Intel Corporation. IBM, PC/AT, VGA, OS/2, and PS/2 are registered trademarks of international Business Machines. Macintosh II Family, LC, LCII, Quandra, and Power Macintosh are registered trademarks of Apply Computer, Inc. VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are trademarks of VESA. The ENERGY STAR name is a registered mark of the U.S. EnvironmentalProtection Agency. Other product names used in this manual are the properties of their respective owners and acknowledged.

♦♦♦

Congratulations!

The display you have just purchased carries the TCO'03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment.

Some of the features of the TCO'03 Display requirements:

Ergonomics

• Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability.

Energy

• Energy-saving mode after a certain time–beneficial both for the user and the

environment

• Electrical safety

Emissions

• Electromagnetic fields

• Noise emissions

Ecology

• The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 001 Restrictions on

chlorinated and brominated flame retardants and polymers heavy metals such as cadmium, mercury and lead.

The requirements included in this label have been developed by TCO Development in cooperation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction. Our labelling system started with displays in 1992 and is now requested by users and IT-manufacturers all over the world.

For more information, please visit

www.tcode velopment.com

♦♦♦

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS .............................................................. 2

INTRODUCTION ............................................................................................... 3

Product Description ................................................................................... 3

Package Overview ...................................................................................... 3

Installation of the Monitor Arm .................................................................. 4

Recommended Use of the Monitor ............................................................. 5

LCD Monitor Base Installation Guide ......................................................... 6

Guidelines for Operating the Viewing Angle of LCD Monitor .................... 7

CONTROLS AND ADJUSTMENTS ...................................................................... 8

Front User Controls. ................................................................................... 8

OSD Directly Adjustment ........................................................................... 9

Brightness............................................................................................ 9

Contrast ............................................................................................... 9

Audio .................................................................................................. 9

OSD Main menu (VGA) .............................................................................. 9

Volume ............................................................................................... 9

Auto-Tune ......................................................................................... 10

Color ................................................................................................. 11

Image ............ Clock/Phase/Image Position/Smooth .......................... 12

Language ........................................................................................... 13

Source ............................................................................................... 13

OSD Position .................................................................................... 13

Reset ................................................................................................. 13

OSD Main menu (DVI) ............................................................................. 14

Volume ............................................................................................. 14

Auto-Tune ......................................................................................... 14

Color ................................................................................................. 15

Image ............ Smooth ...................................................................... 15

Language ........................................................................................... 16

Source ............................................................................................... 16

OSD Position .................................................................................... 16

Reset ................................................................................................. 16

Energy Declaration ................................................................................... 17

TROUBLESHOOTING ...................................................................................... 18

TECHNICAL INFORMATION ........................................................................... 19

Compatibility ............................................................................................ 19

Pin Assignment.................................................................................. 19

Preset Modes ..................................................................................... 19

Other Modes ..................................................................................... 19

Pin Assignment (DVI) ........................................................................ 20

DVI Modes ........................................................................................ 20

Specification ............................................................................................. 21

English

♦♦♦

IMPORTANT SAFETY INSTRUCTIONS

Please read the following instructions carefully. This manual should be retained

English

for future reference.

1. To clean the LCD Monitor screen make sure the Monitor is in the power off mode. Unplug the Monitor from its power source before cleaning it. Stand away from the LCD Monitor and spray cleaning solution onto a rag. Without applying excessive pressure clean the screen with the slightly dampened rag.

2. Do not place your LCD Monitor near a window. Exposing the Monitor to rain, water, moisture or sunlight can severely damage it.

3. Do not place anything on top of the Monitor/PC signal cord. Make sure the cord is placed in an area where it will not be stepped on.

4. Do not apply pressure to the LCD screen. Excessive pressure may cause permanent damage to the display.

5. Do not remove the cover or attempt to service this unit by yourself. You may void the warranty. Servicing of any nature should be performed only by an authorized technician.

6. Safe storage of the LCD Monitor is in a range of minus 20 to plus 60 degrees Celsius. Storing your LCD Monitor outside this range could result in permanent damage.

7. If any of the following occurs immediately unplug your Monitor and call an authorized technician.

• The power or Monitor-to-PC signal cord is frayed or damaged.

• Liquid has been spilled into the Monitor, or it has been exposed to rain.

• The Monitor has been dropped or the case has been damaged.

Notice :

Actual safety specifications please refer to the label on the back of monitor.

♦♦♦

INTRODUCTION

Product Description

Congratulations on purchasing this new generation monitor. Your LCD monitor incorporates high quality display into a small light-weight module. It has power-saving capabilities and emits no X-ray radiation.

The features are:

• 17" TFT Liquid Crystal Display

• Compatible with IBM VGA, VESA

• Direct RGB input

• Direct DVI input

• SXGA 1280x1024 resolution, up to 16M colors

• Lightweight compact design, weighting less than 6.6 Kgs

• DPMS (power saving) Compatible

• Built in universal power supply

• Anti-glare display

• On-Screen Display (OSD) controls and adjustments

• 1W x2 Audio function inside the monitor

• Audio volume adjustment by OSD

Package Overview

Your monitor package contains:

English

Audio CableRGB Cable

LCD Monitor

DVI Cable

CAUTION

Keep the shipping carton in case the need arises to store or transport the unit. Let the

LCD lie on its face when you put it into the carton.

Power Cord

User's Manual

♦♦♦

INTRODUCTION

Installation of the Monitor Arm

English

CAUTION

1. The Monitor Arm is an optional item.

2. The Arm Mounting Device must be VESA Flat Physical Mounting Interface

Standard.

3. Please fix LCD monitor to monitor arm with 4x12mm screw.

♦♦♦

INTRODUCTION

Recommended Use of the Monitor

• Power – Use the type of power indicated on the marking label.

• Plugs – Do not remove any of the prongs of the monitor's three-pronged power plug. – Disconnect the power plug from the AC outlet if you are not going to use it for an

indefinite period of time.

• Power cords – Use the proper power cord with correct attachment plug type. If the power source

is 120 VC, use a power cord that has UL and CSA approvals. If the power source is a 240 VAC supply, use the tandem (T blade) type attachment plug with ground conductor power cord that meets the respective European country's safety regulations, such as VDE for Germany.

– We recommend using the power cord supplied with the product. However, if

another type of power cord is required power cord H05VV-F or VW-1, 18AWG x 3G should be used.

– Do not overload wall outlets or power cords. Ensure that the total of all units

plugged into the wall outlet does not exceed 7 amperes.

– Ensure that the total ampere ratings on all units plugged into the extension cord is

not above the cord's rating.

– If the power supply cord which came with your monitor is to be connected to the

PC instead of the wall outlet, this equipment should be used with UL/TUV approved computers with receptacle rated 100~240V AC, 50/60Hz, 1.1A (minimum).

– Do not allow anything to rest on the power cord. Do not locate this product

where persons will walk on the cord.

• Environment – Place the monitor on a flat level surface. – Place the monitor in a well-ventilated place. – Keep the monitor away from:

rain or water overly hot, cold or humid places sunlight dusty surroundings equipment that generates strong magnetic fields

English

♦♦♦

+ 16 hidden pages