CTX M730V User Manual

User's Manual

M730V LCD Monitor

Federal Communications Commission (F.C.C.) Statement

This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:

• Relocate the receiving antenna.

• Increase the distance between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that which the receiver
is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use only shielded cables or connect I/O devices to this equipment.
You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.

Copyright

This publication including all photographs, illustrations and software, is protected under
international copyright laws, with all rights reserved. Neither this manual nor any of the
material contained herein may be reproduced without the express written consent of the
manufacturer.

Disclaimer

The information in this document is subject to change without notice. The manufacturer
makes no representations or warranties with respect to the contents here of merchantability
or fitness for any particular purpose. Further, the manufacturer reserves the right to revise
this publication ad to make changes from time to time in the content hereof without
obligation of the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS, and Windows are registered trademarks of Microsoft Corp. Intel,
Pentium, and Pentium II are register trademarks of Intel Corporation. IBM, PC/AT, VGA,
OS/2, and PS/2 are registered trademarks of international Business Machines. Macintosh
II Family, LC, LCII, Quandra, and Power Macintosh are registered trademarks of Apply
Computer, Inc. VESA is a registered trademark of the Video Electronics Standards
Association. DPMS and DDC are trademarks of VESA. The ENERGY STAR name is a
registered mark of the U.S. EnvironmentalProtection Agency. Other product names used
in this manual are the properties of their respective owners and acknowledged.

♦♦♦

i

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS .............................................................. 2

INTRODUCTION ............................................................................................... 3

Product Description ................................................................................... 3

Package Overview ...................................................................................... 3

Recommended Use of the Monitor............................................................. 4

The Guideline of Operation Angle of LCD Monito .................................... 5

The Camera Function in LCD Monitor ....................................................... 6

CONTROLS AND ADJUSTMENTS...................................................................... 7

Front User Controls .................................................................................... 7

OSD Main menu ......................................................................................... 8

Auto-Tune........................................................................................ 8

Color ............................................................................................... 9

Image............................................................................................... 9

OSD Setting................................................................................... 10

Language ....................................................................................... 10

Reset.............................................................................................. 10

Source ........................................................................................... 10

Audio setting.................................................................................. 10

Advanced ...................................................................................... 10

Energy Declaration ................................................................................... 11

TROUBLESHOOTING....................................................................................... 12

TECHNICAL INFORMATION............................................................................ 13

Compatibility ............................................................................................ 13

VGA Pin Assignment ..................................................................... 13

VGA Preset Modes ........................................................................ 13

Other Modes ................................................................................. 13

DVI Pin Assignment....................................................................... 14

DVI Modes .................................................................................... 14

Specification ............................................................................................. 15

English

1

♦♦♦

IMPORTANT SAFETY INSTRUCTIONS

Please read the following instructions carefully. This manual should be retained

English

for future reference.

1. To clean the LCD Monitor screen make sure the Monitor is in the power off
mode. Unplug the Monitor from its power source before cleaning it. Stand
away from the LCD Monitor and spray cleaning solution onto a rag. Without
applying excessive pressure clean the screen with the slightly dampened rag.

2. Do not place your LCD Monitor near a window. Exposing the Monitor to
rain, water, moisture or sunlight can severely damage it.

3. Do not place anything on top of the Monitor/PC signal cord. Make sure the
cord is placed in an area where it will not be stepped on.

4. Do not apply pressure to the LCD screen. Excessive pressure may cause
permanent damage to the display.

5. Do not remove the cover or attempt to service this unit by yourself. You may
void the warranty. Servicing of any nature should be performed only by an
authorized technician.

6. Safe storage of the LCD Monitor is in a range of minus 20 to plus 60 degrees
Celsius. Storing your LCD Monitor outside this range could result in permanent
damage.

7. If any of the following occurs immediately unplug your Monitor and call an
authorized technician.

• The power or Monitor-to-PC signal cord is frayed or damaged.

• Liquid has been spilled into the Monitor, or it has been exposed to rain.

• The Monitor has been dropped or the case has been damaged.

Notice :

Actual safety specifications please refer to the label on the back of monitor.

2

♦♦♦

INTRODUCTION

Product Description

Your LCD monitor incorporates high quality display, solid structure and multimedia
savvy. With user-friendly interfaces, user will enjoy the professional PC application
as well as Audio Video performances. In addition, it has power-saving capabilities
and emits no X-ray radiation.

The features are:

• 17" TFT Liquid Crystal Display

• Compatible with IBM VGA, VESA

• Direct VGA input

• Direct DVI input

• USB 2.0 Hub inside

• Equipped with Built-In Camera (640 X 480) with high quality image lens, 1/4”

Color VGA CMOS, and full Space Microphone

• SXGA 1280x1024 resolution, up to 16M colors

• DPMS (power saving) Compatible

• Built in universal power supply

• Anti-glare display

• On-Screen Display (OSD) controls and adjustments

• 3W x2 Audio function inside the monitor

• SRS Surround Sound System

Package Overview

Your monitor package contains:

English

CD x 1

LCD Monitor

USB Cable

CAUTION

Keep the shipping carton in case the need arises to store or transport the unit. Let the

LCD lie on its face when you put it into the carton.

VGA Cable

DVI

Cable

Power Cord

Audio Cable

3

♦♦♦

INTRODUCTION

Recommended Use of the Monitor

English

• Power

– Use the type of power indicated on the marking label.

• Plugs

– Do not remove any of the prongs of the monitor's three-pronged power plug.
– Disconnect the power plug from the AC outlet if you are not going to use it for an

indefinite period of time.

• Power cords

– Use the proper power cord with correct attachment plug type. If the power source

is 120 VC, use a power cord that has UL and CSA approvals. If the power source
is a 240 VAC supply, use the tandem (T blade) type attachment plug with ground
conductor power cord that meets the respective European country's safety
regulations, such as VDE for Germany.

– We recommend using the power cord supplied with the product. However, if

another type of power cord is required power cord H05VV-F or VW-1, 18AWG x
3G should be used.

– Do not overload wall outlets or power cords. Ensure that the total of all units

plugged into the wall outlet does not exceed 7 amperes.

– Ensure that the total ampere ratings on all units plugged into the extension cord is

not above the cord's rating.

– If the power supply cord which came with your monitor is to be connected to the

PC instead of the wall outlet, this equipment should be used with UL/TUV approved
computers with receptacle rated 100~240V AC, 50/60Hz, 1.1A (minimum).

– Do not allow anything to rest on the power cord. Do not locate this product

where persons will walk on the cord.

• Environment

– Place the monitor on a flat level surface.
– Place the monitor in a well-ventilated place.
– Keep the monitor away from:

rain or water
overly hot, cold or humid places
sunlight
dusty surroundings
equipment that generates strong magnetic fields

4

♦♦♦

INTRODUCTION

The Guideline of Operation Angle of LCD Monitor

1. Unpa ck the monitor from Carton box.

2. Put the monitor on a flat table.

3. T o hold the base of monitor with one

hand and pull the frame of panel of
monitor, let the panel up with base
on the vertical position.

4. To adjust the monitor in a

comfortable view position, please
change the tilt angle of panel of
monitor in an optimal position.

5. The normal operation range is

forward 5 degrees to backward 47
degrees. Not allow to operation over
than 47 degree in back direction.

English

6. To adjust the monitor in a

comfortable view position, please
change the high range of panel of
monitor in an optimal position. The
normal operation range is up 55
degrees and down 18 degrees.

5

♦♦♦

INTRODUCTION

The Camera Function in LCD Monitor

English

The Built-in Camera and Microphone are useful tools which enable internet study,
net meeting, chat, and other entertainment purposes & functions.

Camera

The Scope of View Angle

Microphone

LED

The Guideline for Adjusting the
Angle of Camera

0°

UP 45°

90° Position

135° Position

180° Position

6

♦♦♦

CONTROLS AND ADJUSTMENTS

Once you have installed this monitor with your system, please read the instructions
in this section, It provides you some guidelines on how to use the monitor more
efficiently, and lead you through the various functions of the user controls and explain
how to adjust the monitor to your personal preference.

Front User Controls

(1) "ESC" button

To close the OSD(On Screen Display) manual and to escape function or audio mute.

(2) Up

To adjust the selected OSD function or the contrast or select DVI/VGA input.

(3) Down "

To adjust the select e d OSD funct io n or the co nt ras t direc tly .

(4) Enter "

To display the OSD manual and select functions.

(5) Power Switch

To turn the monitor On or Off.

(6) Power LED Indicator

The LED Indicator is for showing the ON/Off of power

(7) Brightnes s C on tro l (S id e Vi ew )

To adjust the brightness directly.

(8) Volume Control (Side View)

To adjust the Volume directly.

(9) Earphone Plug-in (Side View)

∆∆

∆" button

∆∆

∇∇

∇" button

∇∇

↵↵

↵ " button

↵↵

English

7

♦♦♦

CONTROLS AND ADJUSTMENTS

On Screen Display (OSD) Main menu

English

1. Press "

↵ ↵

↵ " to open the OSD main menu.

↵ ↵

2. Use the "∇" and " ∆ " arrows to move through the displayed functions.

3. Press "

↵ ↵

↵ " to confirm your selected function.

↵ ↵

When the main screen starts, there are following functions to choose

1. Auto-Tune (It is disabled in DVI

Mode)

ADVANCED AUTO TUNE PATTERN
PROGRAM USAGE GUIDE

• As some VGA Cards do not match the

When selecting “Auto-Tune”, wait for a
few seconds, the monitor will auto-ad­just Clock, Phase, H-position and V-po­sition to their optimal level.

VESA standard they cannot output 0.7
V p-p VESA standard. Therefore, you
need the "ADVANCED AUTO TUNE
PATTERN PROGRAM" to modify the
parameters of the monitor to match the
different output level of the VGA card.

• AUTO_TUNE.exe is used for Windows
the display mode adjustment. It will
adjust the VGA input level and video
quality to optimum.

• DOS_TUNE.exe is used for 720x400
70Hz & 640x 350 70Hz under DOS
mode adjustment. It will adjust the
video quality to optimum.

• For the adjustment, please execute the
program, then select the "Auto Tune"
function in the OSD menu, to get the
optimal picture.

8

♦♦♦

CONTROLS AND ADJUSTMENTS

2. Color

To enter this item menu, you can choose
either the Auto Color, Color 1, Color 2,
Color 3, Best Color and User mode.

Auto Color It is disabled in
DVI Mode

Color 1

Color 2

Color 3

Best Color

User

3. Image

To enter this item menu, here are some
items which can be adjusted as below.

Auto Geometry It is
disabled in DVI Mode

Clock It is disabled in DVI
Mode

Phase It is disabled in DVI
Mode

H.Position It is disabled in
DVI Mode

V.Position It is disabled in
DVI Mode

Smooth

Zoom

English

Full

Original

Customize

9

♦♦♦

CONTROLS AND ADJUSTMENTS

English

4. OSD Setting

To enter this item menu, it can be
adjusted OSD position and OSD timeout.

H. Position

V. Position

Center

OSD timeout

5. Language

To select the OSD languages between
English, German, French, Spanish,
Italian, Chinese, Japanese or Russian .

~

7. Source

Choosing Input Signal mode.

VGA

DVI

8. Audio setting

To enter this item menu and you can
adjust Surround, Mute or Source.

Surround

Mute

Source

Audio 1 Audio 2

6. Reset

• To select "Yes" or "No".

• Choosing Reset to call-back all the
settings for the current Input Signal
mode to factory preset.

10

♦♦♦

9. Advanced

To enter this item menu, you can select
Text mode or Motion Picture Mode.

Text

Motion Picture

CONTROLS AND ADJUSTMENTS

Energy Declaration

This monitor is equipped with a function for saving energy, which supports the
VESA Display Power Management Signaling (DPMS) standard. This means that
the monitor must be connected to a computer. The time settings for switching to
a power saving mode are adjusted from the system unit by software. From the first
indication of inactivity to power saving position the total time must not be set to
more than 70 minutes.

1. VESA Power-Management Proposal

VESA DPMS Standard

H. sync V. sync Vid eo Stat e

Off On Blank Stand-by

On Off Blank Suspe nd

Off Off Blank Off

2. Power Consumption (120/230 Vac)

KETUNetatsASEVrotacidniDELnoitpmusnoCrewoP

lamroN

noitarepo

gnivaSrewoP

1AnoitisoP

gnivaSrewoP

2AnoitisoP

nOneerGW06<

dnepsuSrebmA

ffOrebmA

≤ W4

≤ W3

English

11

♦♦♦

TROUBLESHOOTING

Troubleshooting

English

If you are experiencing trouble with the LCD display refer to the following. If the
problem persists please contact your local dealer or our service center.

The monitor does not respond after you turn on the system.

• Check if the monitor is turned on.

• Turn off the power and check the monitor power cord and signal cable are properly

connected.

The characters on the screen are dim.

• Refer to the Controls and Adjustments section to adjust the brightness

(BRIGHTNESS on the OSD sub-menu.)

The screen is blank.

• During use the monitor screen may automatically turn off as a result of the Power

Saving feature. Press any key to see if the screen comes back.

• Refer to the Controls and Adjustments section to adjust the brightness

(BRIGHTNESS on the OSD sub-menu.)

The screen flashes when it initializes.

• Turn off the monitor and turn it on again.

• Refer to the Controls and Adjustments section to reload the default setting (RESET

on the OSD main-menu.)

Partial image or incorrectly displayed image

• Check to see if the resolution of your computer is higher than that of the LCD

display

• Reconfigure the resolution of your computer to make it less than or equal

to1280x1024 or to make sure reflesh rate is under 75Hz.

Image has vertical flickering line bars

• Use "Clock" to make an adjustment

• Check and reconfigure the display mode of the vertical refresh rate of your graphic

card to make it compatible with the LCD display

Image is unstable and flickering

• Use "Phase" to make an adjustment.

Signal out of Range:

• When the input signal is outside the normal specifications the screen will display

a "Signal out of Range" message.

No Signal Input:

• The "No Signal Input" message indicates that the cable may not be plugged

properly into the host system.

WARNING

Do not disassemble the monitor. Contact your dealer if needed.

12

♦♦♦

TECHNICAL INFORMATION

Compatibility

This LCD monitor supports multiple operating platforms such as IBM compatible
computers. This section provides you with detailed information on pin assignment
of the D-Sub/DVI connector and the preset timing chart of the prevailing video
standards.

VGA Pin Assignment

langiSbuS-DiniMniP51

oediVdeR1

oediVneerG2

oediVeulB3

cnySlatnoziroH31

cnySlacitreV41

dnuorG11,01,8,7,6,5

noitcennoCoN4

)CDD(ADS21

)CDD(LCS51

.C.N9

latnoziroH

)zHK(ycneuqerF

lacitreV

)zH(ycneuqerF

dradnatS

Male Mini D-15 Connector

VGA Modes

Other Modes

1

6

11

5

10

16

noituloseR)zHM(KLCV

004*027223.82964.13000.07AGVMBI
084*046571.52964.13049.95AGVMBI
084*046005.13168.73008.27ASEV
084*046005.13005.73000.57ASEV
006*008000.04978.73713.06ASEV
006*008000.05770.84881.27ASEV
006*008005.94578.64000.57ASEV

867*4201000.56363.84400.06ASEV
867*4201000.57647.65960.07ASEV
867*4201057.87320.06920.57ASEV

4201*0821000.801189.36310.06ASEV
4201*0821000.531679.97520.57ASEV

468*2511000.801005.76000.57ASEV

English

053*046zH07@
084*046zH07@
006*008zH07@

867*4201zH27@
468*2511zH27,zH07,zH06@
027*0821zH06@
069*0821zH57,zH27,zH07,zH06@

4201*0821zH27@
4201*0821zH07@

13

♦♦♦

DVI Pin Assignment

English

niPtnemngissAlangiSniPtnemngissAlangiSniPtnemngissAlangiS

1-2ataD.S.D.M.T9-1ataD.S.D.M.T71-0ataD.S.D.M.T

2+2ataD.S.D.M.T01+1ataD.S.D.M.T81+0ataD.S.D.M.T
3dleihS4/2ataD.S.D.M.T11dleihS3/1ataD.S.D.M.T91dleihS5/0ataD.S.D.M.T
4tcennoCoN21tcennoCoN02tcennoCoN

5tcennoCoN31tcennoCoN12tcennoCoN

6kcolCCDD41rewoPV5+22dleihSkcolC.S.D.M.T
7ataDCDD51)V5+rof(dnuorG32+kcolC.S.D.M.T
8tcennoCoN61tceteDgulPtoH42-kcolC.S.D.M.T

DVI Modes

TECHNICAL INFORMATION

DVI Connector

14

♦♦♦

Resolution VCLK(MHz)

640*480 25.175 31.469 59.940 IBM VGA

800*600 40.000 37.879 60.000 VESA

1024*768 65.000 48.363 60.000 VESA

1280*1024 108.000 63.981 60.000 VESA

Horizontal

Frequency(KHz)

Vertical

Frequency(Hz)

Standard

TECHNICAL INFORMATION

Specifications

LCD Panel 17" TFT LCD module with wide-viewing angle, 0.264(H)x0.

264(V)mm pixel

[Monitor]

Effective display size 17." (43.2cm diagonal)
Resolution (max.) SXGA 1280x1024
Displayable colors 16M True color
Brightness 400 cd/m
Contrast ratio 500:1
Response time 16ms
Scan Frequency(VGA) Horizontal: 30 to 80kHz Vertical: 59 to 75 Hz
Scan Frequency(DVI) Horizontal: 30 to 66kHz Vertical: 59 to 61 Hz
Audio Input 2V(RMS). Max
Audio Output Stereo, 3W x 2
User controls Power/Enter/Up/Down/Escape/Volume
Power Consumption ≤60W

≤4W Power Saving,
≤3W Power switch off

Input signal Analog 0.7V peak to peak separate

TTL Positive or Negative

Power Supply 100~240V,50/60Hz (automatically)
Plug & Play VGA: DDC 2Bi DVI: DCC 2B
USB Hub Compatible transmissio rate in high speed 480Mb/sec, full

speed 12Mb/sec and low speed 1.5Mb/sec
Down Stream Port x 3 transmission
Per down stream port support current 500mA

[Camera]

pixels 1/4" Color VGA CMOS 640x480
RGB 24bits
resolution Supports160x120,176x144,320x240,352x280,640x480
Object Distance 20cm to Infinity(Minimum)
Microphone Type Non-directional electric
Audio Sample rate 8KHz/16KHz

[Dimension & Weight]

Size (WxDxH) 40.8x209.2x474mm
Weight (net) 6.6 Kgs

[Operating Environment]

Temperature 5°C~35°C
Humidity 20%~80% (non-condensing)

[Storage Environment]

Temperature -20°C~60°C
Humidity 10% ~ 90% (non-condensing)

2

+

English

Note : Specifications are subject to change without notice

15

♦♦♦