C&T Solution RCO-3200-N4200, RCO-3200-4L-M12-N4200, RCO-3200-4P-M12-N4200, RCO-3200-8L-N4200, RCO-3200-8L-M12-N4200 User Manual

USER’S

MANUAL

RCO-3200 Series

Advanced Fanless Embedded System

RCO-3200 | User’s Manual

Table of Contents

Prefaces …………………………………………………….……………………………………………. 04

Revision …………………………………………………………………………………………..……………….………..04

Disclaimer ………………………………………………………..…….…….………………………….………………..04

Copyright Notice …………………………………….…………………….…………………………………………… 04

Trademarks Acknowledgment …………..………………………………………………………...................04

Environmental Protection Announcement …………………………….………………….……………….. 04
Safety Precautions ………………………………………….……………………………….…………….…………..05
Technical Support and Assistance …………………………………….…………….…………….…………….06
Conventions Used in this Manual ………………………………………………………………….….………..06
Package Contents …………………………………………………………………………………………….…………07
Ordering Information …………………………………….……………………………………….……….………… 07

Optional Accessory …………...……………………………………..................................................... 08

Chapter 1 Product Introductions ………………………………………………………..… 09

1.1 Overview ……………………….………………………………..………….…………………………..10

1.1.1 Key Feature ………….……………………………………….……….…..…………….......10

1.2 Hardware Specification ….………………………….....…………….…………..………………11

1.3 System I/O ……………………………..……………………..…………………………………………12

1.3.1 RCO-3200 ………………….…………......................……………………………………12

1.3.2 RCO-3200-4L(P) ……………………………………………………………………………...14

1.3.3 RCO-3200-4L(P)-M12 ………………….………………………………………………... 16

1.3.4 RCO-3200-8L(P) ………………………….……………………………………………….. 18

1.3.5 RCO-3200-8L(P)-M12 ………………….………………………………………………... 20

1.3.6 RCO-3211E(P) ………………….………….................………………………………… 22

1.3.7 RCO-3211E-4L(P) / RCO-3211P-4L(P) …...........………………………………… 24

1.3.8 RCO-3211E-4L(P)-M12 / RCO-3211P-4L(P)-M12 …..………………………… 26

1.3.9 RCO-3222EE(PP) ………………….…………................ ……………………………… 28

1.3.10 RCO-3222EE-4L(P) / RCO-3222PP-4L(P) ………..……………………………… 30

1.3.11 RCO-3222EE-4L(P)-M12 / RCO-3222PP-4L(P)-M12 ….…..……………… 32

1.4 Mechanical Dimensions …………………………..…………………………………….………. 34

1.4.1 RCO-3200 / RCO-3200-4L(P) / RCO-3200-4L(P)-M12 /
RCO-3200-8L(P) / RCO-3200-8L(P)-M12 …….……………..………………….…34

1.4.2 RCO-3211E(P) / RCO-3211E(P)-4L(P) / RCO-3211E(P)-4L(P)-M12 ...... 35

1.4.3 RCO-3222EE(PP) / RCO-3222EE(PP)-4L(P) /
RCO-3222EE(PP)-4L(P)-M12 ………………………………………….……………….. 36

Chapter 2 Switches and Connectors ………………….…………………………………. 37

2.1 Switch and connector Locations ………………………………………..…….……………....38

2.1.1 Top View ………………………………………………………………………..………………38

2.1.2 Bottom View ………………………………………………………………………..………..39

2.1.3 Daughterboard view …………………………………………………………………..…. 39

2.2 Connector / Switch Definition ……………………………….……….…….……….............40

2.3 Switch Definitions ………….……………...............................................................41

2.4 Connector Definitions ………………………….......................................................43

2

RCO-3200 | User’s Manual

3

Chapter 3 System Setup …………………………..……………………………………………56

3.1 Set torque force to 3.5 kgf-cm to execute all the screwing and
unscrewing …………………………………………………………………….……………………….. 57

3.2 Removing chassis bottom cover ……………….…..…….………..…….…….………….… 57

3.3 Removing PCIe/PCI expansion module ……………………………..….….................. 58

3.4 Installing SODIMM ………………….………………….………………………..…….……..….... 59

3.5 Installing Mini PCIe card / mSATA …….………..……….…..…..….………….…….…….. 61

3.6 Installing antenna ……………………………………….…………..……………………………... 62

3.7 Installing HDD on internal SATA HDD bay ….………………………………................ 64

3.8 Installing HDD on removable SATA HDD bay ….…..…………………..………...….... 66

3.9 Installing PCIe/PCI expansion card ….…………..……………….…………..……….….... 67

3.10 Assemble PCIe/PCI expansion module ….………….………….…………..……….….... 69

3.11 Assemble chassis bottom cover ….…………..…………….………………..………..….... 70

3.12 Assemble SIM card ….…………..……………….………………..…………………..…….….... 71

3.13 Assemble wall mount kit ….…………..……………….….………..………………..…..….... 72

3.14 Assemble DIN rail holder ….…………..……………….….………..………………..…..….... 73

Chapter 4 BIOS Setup …………………………………………………………………………… 74

4.1 BIOS Introduction …….……….……………………………………..….…….…..….…………...75

4.2 Main Setup ……..……….………………….…………………………..…….….………………......76

4.2.1 System Date …….……………………………………………..……..……………………....76

4.2.2 System Time ………..…………………………………………..……….…………………...76

4.3 Advanced Setup ………………………………………………………..…………………………….. 77

4.3.1 Trusted Computing (Optional) ……………………………………………………..… 77

4.3.2 ACPI Settings ……..…………………………………………………………..……………….78

4.3.3 Super IO Configuration …………………………….………..…………………..……... 78

4.3.4 Hardware Monitor ………………………………………….………………………..…....82

4.3.5 Serial Port Console Redirection …………………………………....……..…….....83

4.3.6 CPU Configuration ……………………………..……………….………….….…….…....83

4.3.7 Network Stack Configuration ..……………………………..…………..………..... 84

4.3.8 CSM Configuration ……..………………………………..………………………….......85

4.3.9 SATA Configuration …………………………………………………………..………….... 86

4.3.10 USB Configuration ………………………………………………………………………. 87

4.4 Chipset …………...……….………………….…..….…..………………………………………..…....88

4.4.1 North Bridge ………….…………………………………………………..…………………..88

4.4.2 South Bridge ………….………………………………………………..……………………..90

4.5 Security …………...……….………………….…..….…..………………………………..…………...92

4.5.1 Administrators Password …….…………………………………..……………………..92

4.5.2 Users Password …….……………………………….………………..……………………..92

4.6 Boot …………...……….….………………….…..…………………………..…………..……………...93

4.6.1 Setup Prompt Timeout ………………………..…………..……………………………..93

4.6.2 Bootup NumLock State ………………………………………………..………………… 93

4.6.3 Full Screen Logo Show ………………………….…………………………..…...……….93

4.6.4 Boot Option Priorities …………………………..………………………..……………... 93

4.7 Save & Exit …...……….….………………….…..….…..…………………………..…………...... 94

4.7.1 Save Changes and Reset ……………..………………………………..……..……......94

4.7.2 Discard Changes and Reset …………………………………............……………….94

4.7.3 Restore Defaults ……………………………………………………………..……………...94

Appendix WDT & GPIO …………………………………………….……………………….…… 95

WDT Sample Code …….……………………….…….……………..….…….……….…………... 96
GPIO Sample Code ……………………………………………………………………………. 97

RCO-3200 | User’s Manual

4

Revision

Disclaimer

All specifications and information in this User’s Manual are believed to be accurate and up to date. Premio
Inc. does not guarantee that the contents herein are complete, true, accurate or non-misleading. The
information in this document is subject to change without notice and does not represent a commitment on
the part of Premio Inc.
Premio Inc. disclaims all warranties, express or implied, including, without limitation, those of

merchantability, fitness for a particular purpose with respect to contents of this User’s Manual. Users must

take full responsibility for the application of the product.

Copyright Notice

All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means,
electronic or mechanical, including photocopying, recording, or information storage and retrieval systems,
without the prior written permission of Premio Inc. Copyright © Premio Inc.

Trademarks Acknowledgment

Intel®, Celeron® and Pentium® are trademarks of Intel Corporation.
Windows® is registered trademark of Microsoft Corporation.

AMI is trademark of American Megatrend Inc.

IBM, XT, AT, PS/2 and Personal System/2 are trademarks of International Business Machines Corporation
All other products and trademarks mentioned in this manual are trademarks of their respective owners.

Environmental Protection Announcement

Do not dispose this electronic device into the trash while discarding. Please recycle to minimize pollution
and ensure environment protection.

Prefaces

Revision

Description

Date

1.0

Manual Released

2018/12/27

RCO-3200 | User’s Manual

5

Safety Precautions

Before installing and using the equipment, please read the following precautions:

⚫ Put this equipment on a reliable surface during installation. Dropping it or letting it fall could

cause damage.

⚫ The power outlet shall be installed near the equipment and shall be easily accessible.

⚫ Turn off the system power and disconnect the power cord from its source before making any

installation. Be sure both the system and the external devices are turned OFF. Sudden surge

⚫ of power could ruin sensitive components. Make sure the equipment is properly grounded.

⚫ When the power is connected, never open the equipment. The equipment should be opened

only by qualified service personnel.

⚫ Make sure the voltage of the power source is correct before connecting the equipment to the

power outlet.

⚫ Disconnect this equipment from the power before cleaning. Use a damp cloth. Do not use

liquid or spray detergents for cleaning.

⚫ Avoid the dusty, humidity and temperature extremes.

⚫ Do not place heavy objects on the equipment.

⚫ If the equipment is not used for long time, disconnect it from the power to avoid being

damaged by transient over-voltage.

⚫ The storage temperature shall be above -40°C and below 85°C.

⚫ The computer is provided with a battery-powered real-time clock circuit. There is a danger of

explosion if incorrectly replaced. Replace only with the same or equivalent type

recommended by the manufacturer.

⚫ If one of the following situation arises, get the equipment checked be service personnel:

• The power cord or plug is damaged.

• Liquid has penetrated into the equipment.

• The equipment has been exposed to moisture.

• The equipment does not work well or it cannot work according the user’s manual.

• The equipment has been dropped and damaged.

• The equipment has obvious signs of breakage.

Preface

RCO-3200 | User’s Manual

6

Technical Support and Assistance

1. Visit the Premio Inc. website at www.premioinc.com where you can find the latest information

about the product.

2. Contact your distributor, our technical support team or sales representative for technical support if

you need additional assistance. Please have following information ready before you call:

⚫ Model name and serial number

⚫ Description of your peripheral attachments

⚫ Description of your software (operating system, version, application software, etc.)

⚫ A complete description of the problem

⚫ The exact wording of any error messages

Conventions Used in this Manual

Preface

This indication alerts operators to an operation that, if not strictly observed,
may result in severe injury.

WARNING

This indication alerts operators to an operation that, if not strictly observed,
may result in safety hazards to personnel or damage to equipment.

CAUTION

This indication provides additional information to complete a task easily.

NOTE

RCO-3200 | User’s Manual

7

Package Contents

Before installation, please ensure all the items listed in the following table are included in the package.

Item Description Q’ty

1

RCO-3200 Series Embedded System

1

2

Utility DVD Driver 1

3

Wall Mount Kit 1

4 Accessory Kit

1

5 DVI to VGA Adapter

1

Ordering Information

Preface

Model No. Product Description

RCO-3200-N4200 Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN

RCO-3200-4L-N4200 Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 6x LAN

RCO-3200-4P-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,

4x PoE

RCO-3200-4L-M12-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
4x M12 LAN

RCO-3200-4P-M12-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
4x M12 PoE

RCO-3200-8L-N4200 Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 10x LAN

RCO-3200-8P-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
8x PoE

RCO-3200-8L-M12-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
8x M12 LAN

RCO-3200-8P-M12-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
8x M12 PoE

RCO-3211E-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,

1x PCIe Slot

RCO-3211E-4L-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 6x LAN,
1x PCIe Slot

RCO-3211E-4P-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
4x PoE, 1x PCIe Slot

RCO-3211E-4L-M12-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
4x M12 LAN, 1x PCIe Slot

RCO-3211E-4P-M12-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
4x M12 PoE, 1x PCIe Slot

RCO-3200 | User’s Manual

8

Preface

Optional Accessories

Model No. Product Description

1

-E09A06007

Adapter AC/DC 12V 5A 60W with 3pin Terminal Block Plug 5.0mm Pitch

1

-E09A12002

Adapter AC/DC 24V 5A 120W with 3pin Terminal Block Plug 5.0mm Pitch

SFICBL022

Power Cord, 3

-pin US Type, 180cm

1

-TPCD00002

Power Cord, European Type, 180cm

1

-TPCD00001

Power Cord, 3

-pin UK Type, 180cm

Ordering Information

Model No. Product Description

RCO-3211P-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
1x PCI Slot

RCO-3211P-4L-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 6x LAN,
1x PCI Slot

RCO-3211P-4P-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,

4x PoE, 1x PCI Slot

RCO-3211P-4L-M12-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
4x M12 LAN, 1x PCI Slot

RCO-3211P-4P-M12-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
4x M12 PoE, 1x PCI Slot

RCO-3222EE-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
2x PCIe Slot

RCO-3222EE-4L-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 6x LAN,
2x PCIe Slot

RCO-3222EE-4P-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
4x PoE, 2x PCIe Slot

RCO-3222EE-4L-M12-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
4x M12 LAN, 2x PCIe Slot

RCO-3222EE-4P-M12-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
4x M12 PoE, 2x PCIe Slot

RCO-3222PP-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
2x PCI Slot

RCO-3222PP-4L-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 6x LAN,
2x PCI Slot

RCO-3222PP-4P-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
4x PoE, 2x PCI Slot

RCO-3222PP-4L-M12-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,
4x M12 LAN, 2x PCI Slot

RCO-3122PP-4P-M12-N4200

Advanced Fanless Embedded System with Intel® Pentium® Processor N4200, 2x LAN,

4x M12 PoE, 2x PCI Slot

Chapter 1

Product Introductions

RCO-3200 | User’s Manual

10

1.1 Overview

Based on Intel® Pentium® N4200 (2.5GHz) Quad Core processor, RCO-3200 series is an extreme features
integration, outstanding system performance, versatile I/O connections, and rugged reliability fanless
embedded systems. It offers modularize expansion I/O, rich connectivity interfaces, wide range (9~50V)
DC power input, and high reliability even operating in temperature extremes (-40°C ~ +70°C).

Featuring with completely cable-less designed, high functional, one-piece housing design, and anti­vibration, RCO-3200 series are ruggedized systems that can operate in harsh environments and easy to
install and maintain. A build in over voltage protection (OVP), over current protection (OCP), reserve
voltage protection, and wide range DC power input makes RCO-3200 series are safety system for all
industrial applications.

Chapter 1: Product Introductions

RCO-3200 Series RCO-3211 Series RCO-3222 Series

1.1.1 Key Features

⚫ Intel® Pentium®N4200 (2.5GHz) Quad Core processor
⚫ 1x DDR3L SO-DIMM Max. up to 8GB (un-buffered)
⚫ Triple Independent Display from 1x DVI-I and 1x DisplayPort
⚫ 2x Intel® GbE Port, Support Wake-on-LAN and PXE [RCO-3200, RCO-3211E(P), and RCO-3222EE(PP) Only]

⚫ 6x Intel® GbE Port, Support Wake-on-LAN and PXE [RCO-3200-4L, RCO-3200-4L-M12, RCO-3211E(P)-4L, RCO-

3211E(P)-4L-M12, RCO-3222EE(PP)-4L, and RCO-3222EE(PP)-4L-M12 Only]

⚫ 10x Intel® GbE Port, Support Wake-on-LAN and PXE (RCO-3200-8L Only)
⚫ 6x Intel® GbE Port with 4x PoE Function, Support Wake-on-LAN, 2x Support PXE [RCO-3200-4P, RCO-

3200-4P-M12, RCO-3211E(P)-4P, RCO-3211E(P)-4P-M12, RCO-3222EE(PP)-4P, and RCO-3222EE(PP)-4P-M12 Only]

⚫ 2x USB 3.0, 2x USB 2.0
⚫ 6x RS232/422/485 Port
⚫ 8x Isolated DI, 8x Isolated DO
⚫ 1x Removable 2.5" SATA HDD Bay and 1x Internal 2.5” SATA SSD/HDD Bay
⚫ 1x mSATA (Shared by 1x Mini-PCIe Socket and 1x SATA) and 2x SIM Card Socket
⚫ 9~48VDC Power Input, support AT/ATX Mode

⚫ 2x Mini-PCIe Socket for Wi-Fi, GSM, or I/O Expansion

⚫ 1x PCIe x4 (1-lane) Expansion (RCO-3211E Series Only)
⚫ 1x PCI Expansion (RCO-3211P Series Only)
⚫ 2x PCIe x4 (1-lane) Expansion (RCO-3222EE Series Only)
⚫ 2x PCI Expansion (RCO-3222PP Series Only)
⚫ Power Ignition Sensing
⚫ Remote Power On/Off Switch/

RCO-3200 | User’s Manual

11

1.2 Hardware Specification

Chapter 1: Product Introductions

Processor System

• Intel® Pentium® N4200 Quad Core Processor, 2.5 GHz

with 128Mbit SPI BIOS.

Memory

• 1x 204-Pin DDR3L-1600 / 1867MHz SO-DIMM (un­buffered and non-ECC), max. up to 8GB

Display

Triple Display

• 1x DVI-D and 1x VGA (w/ Optional Split Cable)

• 1x DVI-D and 1x DisplayPort

• 1x DisplayPort and 1x VGA

Expansion

• RCO-3211E Series: 1x PCIe x4 (1-lane)

• RCO-3311P Series: 1x PCI

• RCO-3322EE Series : 2x PCIe x4 (1-lane)

• RCO-3322PP Series: 2x PCI

• 2x Full-size Mini PCIe Socket for Wi-Fi / GSM / Expansion

Module

• 1x Universal I/O Bracket [RCO-3211E-4L(4P), RCO-3211E-4L(4P)-

M12, RCO-3211P-4L(4P), RCO-3211P-4L(4P)-M12, RCO-3222EE-4L(4P),
RCO-3222EE-4L(4P)-M12, RCO-3222PP-4L(4P), and RCO-3222PP­4L(4P)-M12 Only]

• 2x Universal I/O Bracket (RCO-3200, RCO-3211E, RCO-3211P,

RCO-3222EE, and RCO-3222PP Only)

Ethernet

• 2x Intel® i210-AT GbE LAN Port, Support Wake-on-LAN
and PXE [RCO-3200, RCO-3211E(P),RCO-3222EE(PP) Only]

• 6x Intel® i210-AT GbE LAN Port, LAN1 and LAN2 Support
Wake-on-LAN [RCO-3200-4L, RCO-3200-4L-M12, RCO-3211E(P)-4L,

RCO-3211E(P)-4L-M12, RCO-3222EE(PP)-4L, and RCO-3222EE(PP)-4L­M12 Only]

• 10x Intel® i210-AT GbE LAN Port, LAN1 and LAN2
Support Wake-on-LAN [RCO-3200-8L and RCO-3200-8L-M12

Only]

• 4x 802.3at Compliant PoE Port, The Maximum DC Power
Delivery on Each PoE is 25.5W [RCO-3200-4P, RCO-3200-4P-

M12, RCO-3211E(P)-4P, RCO-3211E(P)-4P-M12, RCO-3222EE(PP)-4P,
and RCO-3222EE(PP)-4P-M12 Only]

• 8x 802.3at Compliant PoE Port, The Maximum DC Power

Delivery on Each PoE is 10W (RCO-3200-8P and RCO-3200-8P-

M12 Only)

Audio

• Codec: Realtek ALC888S

• 1x Mic-in and 1x Line-out

Watchdog Timer

• Software Programmable Supports 1~255 sec. System
Reset

Storage

• 1x Removable 2.5" SATA HDD Bay

• 1x Internal 2.5" SATA HDD Bay

• 1x CFast Socket

• 1x mSATA Socket (Shared by 1x Mini-PCIe and SATA)

• 2x External SIM Card Socket

I/O Ports

• 2x USB 3.0 Port

• 2x USB 2.0 Port

• 8 Isolated DI and 8 Isolated DO Port

• 2x DB9 Flow Control for COM1~2, Support

RS232/422/485 with Auto Flow Control

• 4x Internal connector for COM3~6, Support
RS232/422/485 with Auto Flow Control

• 4x Antenna Hole

• 1x Power Switch

• 1x AT/ATX Switch

• 1x Remote Power on/off Connector

Digital Input & Output

• 8x Digital Input (Source Type)

- Input Voltage (Dry Contact):
Logic 0: Close to GND
Logic 1: Open

- Input Voltage:
Logic 0: 3V max.
Logic 1: 5V min. (DI to COM-)

• 8x Digital Output

- Supply Voltage: 5~30VDC

- Sink Current: 200 mA Max. Per Channel

Power

• Support AT, ATX Mode

• 1x 3-pin Terminal Block Connector with Power Input

9~50VDC

• Power Ignition Sensing

• 1x Optional AC/DC 12V/5A, 60W Power Adapter

• 1x Optional AC/DC 24V/5A, 120W Power Adapter [RCO-

3200-4P, RCO-3200-4P-M12, RCO-3200-8P, RCO-3200-8P-M12, RCO­3211E(P)-4P, RCO-3211E(P)-4P-M12, RCO-3222EE(PP)-4P, and RCO­3222EE(PP)-4P-M12 Series Only]

Environment

• Operating Temperature: Ambient with Air Flow:

-40°C to 70°C (with Industrial Grade Peripherals)

• Storage Temperature: -40°C to 85°C

• Relative humidity: 10%~95% (non-condensing)

Physical

• RCO-3200 Series

✓ Dimension (WxDxH, mm): 185 x 197 x 57.4 mm
✓ Weight: 1.93 kg ~ 2.35 kg

• RCO-3211 Series

✓ Dimension (WxDxH, mm): 185 x 197 x 84.9 mm
✓ Weight: 2.43 kg ~ 2.79 kg

• RCO-3222 Series

✓ Dimension (WxDxH, mm): 185 x 197 x 104.9 mm
✓ Weight: 2.83 kg ~ 3.38 kg

• Construction: Extruded Aluminum with Heavy Duty
Metal

• Mounting: Wall/ DIN-Rail Mounting

Operating System

• Windows® 10

• Linux kernel 4.x

Certifications

• CE / FCC Class A

RCO-3200 | User’s Manual

12

1.3 System I/O

1.3.1 RCO-3200

Chapter 1: Product Introductions

Front Panel

Power on/off switch

Press to power-on or power-off the system

Reset switch

Press to reset the system

AT/ATX mode select switch

Used to select AT or ATX power mode

PC/Car mode select switch

Used to select PC or Car mode

Delay time select switch

Used to select car mode PC turn off delay time

CFast Socket

Used to insert CFast card

SIM card

Used to insert SIM card

Universal I/O Bracket

Used to customized I/O output

HDD port

Removable 2.5" SATA HDD Area

Power LED

Indicates the power status of the system

HDD LED

Indicates the status of the hard drive

Ethernet LEDs

Indicates the status of the LAN active

GPIO LED

Indicates the status of the customer define

Watchdog LED

Indicates the status of the watchdog active

RCO-3200 | User’s Manual

13

Chapter 1: Product Introductions

Rear Panel

DC IN

Used to plug a DC power input with terminal
block

DVI-I port

Used to connect a DVI monitor or connect
optional split cable for dual display mode

DisplayPort

Used to connect a DisplayPort monitor

Line-out

Used to connect a speaker

Mic-in

Used to connect a microphone

USB 3.0 port

Used to connect USB 3.0/2.0/1.1 device

USB 2.0 port

Used to connect USB 2.0/1.1 device

LAN port

Used to connect the system to a local area
network

Remote Power on/off Terminal Block

Used to plug a remote power on/off terminal
block

COM port

COM1 ~ COM2 support RS232/422/485 serial
device

Digital I/O Terminal Block

The Digital I/O terminal block supports 8 digital
input and 8 digital output

Antenna hole

Used to connect an antenna for optional Mini­PCIe WiFi module

RCO-3200 | User’s Manual

14

1.3.2 RCO-3200-4L(P)

Chapter 1: Product Introductions

Front Panel

Power on/off switch

Press to power-on or power-off the system

Reset switch

Press to reset the system

AT/ATX mode select switch

Used to select AT or ATX power mode

PC/Car mode select switch

Used to select PC or Car mode

Delay time select switch

Used to select car mode PC turn off delay time

CFast Socket

Used to insert CFast card

SIM card

Used to insert SIM card

LAN port

Used to connect the system to a local area
network (RCO-3200-4L Only)

PoE Port

Used to connect the system to a local area
network with power over Ethernet (RCO-3200-4P
Only)

Universal I/O Bracket

Used to customized I/O output

HDD port

Removable 2.5" SATA HDD Area

Power LED

Indicates the power status of the system

HDD LED

Indicates the status of the hard drive

Ethernet LEDs

Indicates the status of the LAN active

GPIO LED

Indicates the status of the customer define

Watchdog LED

Indicates the status of the watchdog active

RCO-3200 | User’s Manual

15

Chapter 1: Product Introductions

Rear Panel

DC IN

Used to plug a DC power input with terminal
block

DVI-I port

Used to connect a DVI monitor or connect
optional split cable for dual display mode

DisplayPort

Used to connect a DisplayPort monitor

Line-out

Used to connect a speaker

Mic-in

Used to connect a microphone

USB 3.0 port

Used to connect USB 3.0/2.0/1.1 device

USB 2.0 port

Used to connect USB 2.0/1.1 device

LAN port

Used to connect the system to a local area
network

Remote Power on/off Terminal Block

Used to plug a remote power on/off terminal
block

COM port

COM1 ~ COM2 support RS232/422/485 serial
device

Digital I/O Terminal Block

The Digital I/O terminal block supports 8 digital
input and 8 digital output

Antenna hole

Used to connect an antenna for optional Mini­PCIe WiFi module

RCO-3200 | User’s Manual

16

1.3.3 RCO-3200-4L(P)-M12

Chapter 1: Product Introductions

Front Panel

Power on/off switch

Press to power-on or power-off the system

Reset switch

Press to reset the system

AT/ATX mode select switch

Used to select AT or ATX power mode

PC/Car mode select switch

Used to select PC or Car mode

Delay time select switch

Used to select car mode PC turn off delay time

CFast Socket

Used to insert CFast card

SIM card

Used to insert SIM card

M12 LAN Port

Used to connect the system to a local area
network (RCO-3200-4L-M12 Only)

M12 PoE Port

Used to connect the system to a local area
network with power over Ethernet (RCO-3200­4P-M12 Only)

Universal I/O Bracket

Used to customized I/O output

HDD port

Removable 2.5" SATA HDD Area

Power LED

Indicates the power status of the system

HDD LED

Indicates the status of the hard drive

Ethernet LEDs

Indicates the status of the LAN active

GPIO LED

Indicates the status of the customer define

Watchdog LED

Indicates the status of the watchdog active

RCO-3200 | User’s Manual

17

Chapter 1: Product Introductions

Rear Panel

DC IN

Used to plug a DC power input with terminal
block

DVI-I port

Used to connect a DVI monitor or connect
optional split cable for dual display mode

DisplayPort

Used to connect a DisplayPort monitor

Line-out

Used to connect a speaker

Mic-in

Used to connect a microphone

USB 3.0 port

Used to connect USB 3.0/2.0/1.1 device

USB 2.0 port

Used to connect USB 2.0/1.1 device

LAN port

Used to connect the system to a local area
network

Remote Power on/off Terminal Block

Used to plug a remote power on/off terminal
block

COM port

COM1 ~ COM2 support RS232/422/485 serial
device

Digital I/O Terminal Block

The Digital I/O terminal block supports 8 digital
input and 8 digital output

Antenna hole

Used to connect an antenna for optional Mini­PCIe WiFi module

RCO-3200 | User’s Manual

18

Chapter 1: Product Introductions

1.3.4 RCO-3200-8L(P)

Front Panel

Power on/off switch

Press to power-on or power-off the system

Reset switch

Press to reset the system

AT/ATX mode select switch

Used to select AT or ATX power mode

PC/Car mode select switch

Used to select PC or Car mode

Delay time select switch

Used to select car mode PC turn off delay time

CFast Socket

Used to insert CFast card

SIM card

Used to insert SIM card

LAN port

Used to connect the system to a local area
network (RCO-3200-8L Only)

PoE Port

Used to connect the system to a local area
network with power over Ethernet (RCO-3200-8P
Only)

HDD port

Removable 2.5" SATA HDD Area

Power LED

Indicates the power status of the system

HDD LED

Indicates the status of the hard drive

Ethernet LEDs

Indicates the status of the LAN active

GPIO LED

Indicates the status of the customer define

Watchdog LED

Indicates the status of the watchdog active

RCO-3200 | User’s Manual

19

Chapter 1: Product Introductions

Rear Panel

DC IN

Used to plug a DC power input with terminal
block

DVI-I port

Used to connect a DVI monitor or connect
optional split cable for dual display mode

DisplayPort

Used to connect a DisplayPort monitor

Line-out

Used to connect a speaker

Mic-in

Used to connect a microphone

USB 3.0 port

Used to connect USB 3.0/2.0/1.1 device

USB 2.0 port

Used to connect USB 2.0/1.1 device

LAN port

Used to connect the system to a local area
network

Remote Power on/off Terminal Block

Used to plug a remote power on/off terminal
block

COM port

COM1 ~ COM2 support RS232/422/485 serial
device

Digital I/O Terminal Block

The Digital I/O terminal block supports 8 digital
input and 8 digital output

Antenna hole

Used to connect an antenna for optional Mini­PCIe WiFi module

RCO-3200 | User’s Manual

20

Chapter 1: Product Introductions

1.3.5 RCO-3200-8L(P)-M12

Front Panel

Power on/off switch

Press to power-on or power-off the system

Reset switch

Press to reset the system

AT/ATX mode select switch

Used to select AT or ATX power mode

PC/Car mode select switch

Used to select PC or Car mode

Delay time select switch

Used to select car mode PC turn off delay time

CFast Socket

Used to insert CFast card

SIM card

Used to insert SIM card

M12 LAN Port

Used to connect the system to a local area
network (RCO-3200-8L-M12 Only)

M12 PoE Port

Used to connect the system to a local area
network with power over Ethernet (RCO-3200­8P-M12 Only)

HDD port

Removable 2.5" SATA HDD Area

Power LED

Indicates the power status of the system

HDD LED

Indicates the status of the hard drive

Ethernet LEDs

Indicates the status of the LAN active

GPIO LED

Indicates the status of the customer define

Watchdog LED

Indicates the status of the watchdog active

RCO-3200 | User’s Manual

21

Chapter 1: Product Introductions

Rear Panel

DC IN

Used to plug a DC power input with terminal
block

DVI-I port

Used to connect a DVI monitor or connect
optional split cable for dual display mode

DisplayPort

Used to connect a DisplayPort monitor

Line-out

Used to connect a speaker

Mic-in

Used to connect a microphone

USB 3.0 port

Used to connect USB 3.0/2.0/1.1 device

USB 2.0 port

Used to connect USB 2.0/1.1 device

LAN port

Used to connect the system to a local area
network

Remote Power on/off Terminal Block

Used to plug a remote power on/off terminal
block

COM port

COM1 ~ COM2 support RS232/422/485 serial
device

Digital I/O Terminal Block

The Digital I/O terminal block supports 8 digital
input and 8 digital output

Antenna hole

Used to connect an antenna for optional Mini­PCIe WiFi module

RCO-3200 | User’s Manual

22

1.3.6 RCO-3211E(P)

Chapter 1: Product Introductions

Front Panel

Power on/off switch

Press to power-on or power-off the system

Reset switch

Press to reset the system

AT/ATX mode select switch

Used to select AT or ATX power mode

PC/Car mode select switch

Used to select PC or Car mode

Delay time select switch

Used to select car mode PC turn off delay time

CFast Socket

Used to insert CFast card

SIM card

Used to insert SIM card

Universal I/O Bracket

Used to customized I/O output

HDD port

Removable 2.5" SATA HDD Area

Power LED

Indicates the power status of the system

HDD LED

Indicates the status of the hard drive

Ethernet LEDs

Indicates the status of the LAN active

GPIO LED

Indicates the status of the customer define

Watchdog LED

Indicates the status of the watchdog active

RCO-3200 | User’s Manual

23

Chapter 1: Product Introductions

Rear Panel

DC IN

Used to plug a DC power input with terminal
block

DVI-I port

Used to connect a DVI monitor or connect
optional split cable for dual display mode

DisplayPort

Used to connect a DisplayPort monitor

Line-out

Used to connect a speaker

Mic-in

Used to connect a microphone

USB 3.0 port

Used to connect USB 3.0/2.0/1.1 device

USB 2.0 port

Used to connect USB 2.0/1.1 device

LAN port

Used to connect the system to a local area
network

Remote Power on/off Terminal Block

Used to plug a remote power on/off terminal
block

COM port

COM1 ~ COM2 support RS232/422/485 serial
device

Digital I/O Terminal Block

The Digital I/O terminal block supports 8 digital
input and 8 digital output

Expansion Area

Used to plug PCIe Card (RCO-3211E Only)
Used to plug PCI Card (RCO-3211P Only)

Antenna hole

Used to connect an antenna for optional Mini­PCIe WiFi module

RCO-3200 | User’s Manual

24

1.3.7 RCO-3211E-4L(P) / RCO-3211P-4L(P)

Chapter 1: Product Introductions

Front Panel

Power on/off switch

Press to power-on or power-off the system

Reset switch

Press to reset the system

AT/ATX mode select switch

Used to select AT or ATX power mode

PC/Car mode select switch

Used to select PC or Car mode

Delay time select switch

Used to select car mode PC turn off delay time

CFast Socket

Used to insert CFast card

SIM card

Used to insert SIM card

LAN port

Used to connect the system to a local area
network (RCO-3211E/P-4L Only)

PoE Port

Used to connect the system to a local area
network with power over Ethernet (RCO­3211E/P-4P Only)

Universal I/O Bracket

Used to customized I/O output

HDD port

Removable 2.5" SATA HDD Area

Power LED

Indicates the power status of the system

HDD LED

Indicates the status of the hard drive

Ethernet LEDs

Indicates the status of the LAN active

GPIO LED

Indicates the status of the customer define

Watchdog LED

Indicates the status of the watchdog active

RCO-3200 | User’s Manual

25

Chapter 1: Product Introductions

Rear Panel

DC IN

Used to plug a DC power input with terminal
block

DVI-I port

Used to connect a DVI monitor or connect
optional split cable for dual display mode

DisplayPort

Used to connect a DisplayPort monitor

Line-out

Used to connect a speaker

Mic-in

Used to connect a microphone

USB 3.0 port

Used to connect USB 3.0/2.0/1.1 device

USB 2.0 port

Used to connect USB 2.0/1.1 device

LAN port

Used to connect the system to a local area
network

Remote Power on/off Terminal Block

Used to plug a remote power on/off terminal
block

COM port

COM1 ~ COM2 support RS232/422/485 serial
device

Digital I/O Terminal Block

The Digital I/O terminal block supports 8 digital
input and 8 digital output

Expansion Area

Used to plug PCIe Card (RCO-3211E-4L/4P Only)
Used to plug PCI Card (RCO-3211P-4L/4P Only)

Antenna hole

Used to connect an antenna for optional Mini­PCIe WiFi module

RCO-3200 | User’s Manual

26

1.3.8 RCO-3211E-4L(P)-M12 / RCO-3211P-4L(P)-M12

Chapter 1: Product Introductions

Front Panel

Power on/off switch

Press to power-on or power-off the system

Reset switch

Press to reset the system

AT/ATX mode select switch

Used to select AT or ATX power mode

PC/Car mode select switch

Used to select PC or Car mode

Delay time select switch

Used to select car mode PC turn off delay time

CFast Socket

Used to insert CFast card

SIM card

Used to insert SIM card

M12 LAN Port

Used to connect the system to a local area
network (RCO-3211E/P-4L-M12 Only)

M12 PoE Port

Used to connect the system to a local area
network with power over Ethernet (RCO­3211E/P-4P-M12 Only)

Universal I/O Bracket

Used to customized I/O output

HDD port

Removable 2.5" SATA HDD Area

Power LED

Indicates the power status of the system

HDD LED

Indicates the status of the hard drive

Ethernet LEDs

Indicates the status of the LAN active

GPIO LED

Indicates the status of the customer define

Watchdog LED

Indicates the status of the watchdog active

RCO-3200 | User’s Manual

27

Chapter 1: Product Introductions

Rear Panel

DC IN

Used to plug a DC power input with terminal
block

DVI-I port

Used to connect a DVI monitor or connect
optional split cable for dual display mode

DisplayPort

Used to connect a DisplayPort monitor

Line-out

Used to connect a speaker

Mic-in

Used to connect a microphone

USB 3.0 port

Used to connect USB 3.0/2.0/1.1 device

USB 2.0 port

Used to connect USB 2.0/1.1 device

LAN port

Used to connect the system to a local area
network

Remote Power on/off Terminal Block

Used to plug a remote power on/off terminal
block

COM port

COM1 ~ COM2 support RS232/422/485 serial
device

Digital I/O Terminal Block

The Digital I/O terminal block supports 8 digital
input and 8 digital output

Expansion Area

Used to plug PCIe Card (RCO-3211E-4L/4P-M12
Only)
Used to plug PCI Card (RCO-3211P-4L/4P-M12
Only)

Antenna hole

Used to connect an antenna for optional Mini­PCIe WiFi module

RCO-3200 | User’s Manual

28

1.3.9 RCO-3222EE(PP)

Chapter 1: Product Introductions

Front Panel

Power on/off switch

Press to power-on or power-off the system

Reset switch

Press to reset the system

AT/ATX mode select switch

Used to select AT or ATX power mode

PC/Car mode select switch

Used to select PC or Car mode

Delay time select switch

Used to select car mode PC turn off delay time

CFast Socket

Used to insert CFast card

SIM card

Used to insert SIM card

Universal I/O Bracket

Used to customized I/O output

HDD port

Removable 2.5" SATA HDD Area

Power LED

Indicates the power status of the system

HDD LED

Indicates the status of the hard drive

Ethernet LEDs

Indicates the status of the LAN active

GPIO LED

Indicates the status of the customer define

Watchdog LED

Indicates the status of the watchdog active

RCO-3200 | User’s Manual

29

Chapter 1: Product Introductions

Rear Panel

DC IN

Used to plug a DC power input with terminal
block

DVI-I port

Used to connect a DVI monitor or connect
optional split cable for dual display mode

DisplayPort

Used to connect a DisplayPort monitor

Line-out

Used to connect a speaker

Mic-in

Used to connect a microphone

USB 3.0 port

Used to connect USB 3.0/2.0/1.1 device

USB 2.0 port

Used to connect USB 2.0/1.1 device

LAN port

Used to connect the system to a local area
network

Remote Power on/off Terminal Block

Used to plug a remote power on/off terminal
block

COM port

COM1 ~ COM2 support RS232/422/485 serial
device

Digital I/O Terminal Block

The Digital I/O terminal block supports 8 digital
input and 8 digital output

Expansion Area

Used to plug PCIe Card (RCO-3222EE Only)
Used to plug PCI Card (RCO-3222PP Only)

Antenna hole

Used to connect an antenna for optional Mini­PCIe WiFi module

RCO-3200 | User’s Manual

30

1.3.10 RCO-3222EE-4L(P) / RCO-3222PP-4L(P)

Chapter 1: Product Introductions

Front Panel

Power on/off switch

Press to power-on or power-off the system

Reset switch

Press to reset the system

AT/ATX mode select switch

Used to select AT or ATX power mode

PC/Car mode select switch

Used to select PC or Car mode

Delay time select switch

Used to select car mode PC turn off delay time

CFast Socket

Used to insert CFast card

SIM card

Used to insert SIM card

LAN port

Used to connect the system to a local area
network (RCO-3222EE/PP-4L Only)

PoE Port

Used to connect the system to a local area
network with power over Ethernet (RCO­3222EE/PP-4P Only)

Universal I/O Bracket

Used to customized I/O output

HDD port

Removable 2.5" SATA HDD Area

Power LED

Indicates the power status of the system

HDD LED

Indicates the status of the hard drive

Ethernet LEDs

Indicates the status of the LAN active

GPIO LED

Indicates the status of the customer define

Watchdog LED

Indicates the status of the watchdog active

RCO-3200 | User’s Manual

31

Chapter 1: Product Introductions

Rear Panel

DC IN

Used to plug a DC power input with terminal
block

DVI-I port

Used to connect a DVI monitor or connect
optional split cable for dual display mode

DisplayPort

Used to connect a DisplayPort monitor

Line-out

Used to connect a speaker

Mic-in

Used to connect a microphone

USB 3.0 port

Used to connect USB 3.0/2.0/1.1 device

USB 2.0 port

Used to connect USB 2.0/1.1 device

LAN port

Used to connect the system to a local area
network

Remote Power on/off Terminal Block

Used to plug a remote power on/off terminal
block

COM port

COM1 ~ COM2 support RS232/422/485 serial
device

Digital I/O Terminal Block

The Digital I/O terminal block supports 8 digital
input and 8 digital output

Expansion Area

Used to plug PCIe Card (RCO-3222EE-4L/4P Only)
Used to plug PCI Card (RCO-3222PP-4L/4P Only)

Antenna hole

Used to connect an antenna for optional Mini­PCIe WiFi module

RCO-3200 | User’s Manual

32

1.3.11 RCO-3222EE-4L(P)-M12 / RCO-3222PP-4L(P)-M12

Chapter 1: Product Introductions

Front Panel

Power on/off switch

Press to power-on or power-off the system

Reset switch

Press to reset the system

AT/ATX mode select switch

Used to select AT or ATX power mode

PC/Car mode select switch

Used to select PC or Car mode

Delay time select switch

Used to select car mode PC turn off delay time

CFast Socket

Used to insert CFast card

SIM card

Used to insert SIM card

M12 LAN Port

Used to connect the system to a local area
network (RCO-3222EE/PP-4L-M12 Only)

M12 PoE Port

Used to connect the system to a local area
network with power over Ethernet (RCO­3222EE/PP-4P-M12 Only)

Universal I/O Bracket

Used to customized I/O output

HDD port

Removable 2.5" SATA HDD Area

Power LED

Indicates the power status of the system

HDD LED

Indicates the status of the hard drive

Ethernet LEDs

Indicates the status of the LAN active

GPIO LED

Indicates the status of the customer define

Watchdog LED

Indicates the status of the watchdog active

RCO-3200 | User’s Manual

33

Chapter 1: Product Introductions

Rear Panel

DC IN

Used to plug a DC power input with terminal
block

DVI-I port

Used to connect a DVI monitor or connect
optional split cable for dual display mode

DisplayPort

Used to connect a DisplayPort monitor

Line-out

Used to connect a speaker

Mic-in

Used to connect a microphone

USB 3.0 port

Used to connect USB 3.0/2.0/1.1 device

USB 2.0 port

Used to connect USB 2.0/1.1 device

LAN port

Used to connect the system to a local area
network

Remote Power on/off Terminal Block

Used to plug a remote power on/off terminal
block

COM port

COM1 ~ COM2 support RS232/422/485 serial
device

Digital I/O Terminal Block

The Digital I/O terminal block supports 8 digital
input and 8 digital output

Expansion Area

Used to plug PCIe Card (RCO-3222EE-4L/4P-M12
Only)
Used to plug PCI Card (RCO-3211PP-4L/4P-M12
Only)

Antenna hole

Used to connect an antenna for optional Mini­PCIe WiFi module

RCO-3200 | User’s Manual

34

1.4 Mechanical Dimensions

1.4.1 RCO-3200 / RCO-3200-4L(P) / RCO-3200-4L(P)-M12 / RCO-3200-8L(P) /
RCO-3200-8L(P)-M12

Unit: mm

Chapter 1: Product Introductions

RCO-3200 | User’s Manual

35

1.4.2 RCO-3211E(P) / RCO-3211E(P)-4L(P) / RCO-3211E(P)-4L(P)-M12

Unit: mm

Chapter 1: Product Introductions

RCO-3200 | User’s Manual

36

1.4.3 RCO-3222EE(PP) / RCO-3222EE(PP)-4L(P) / RCO-3222EE(PP)-4L(P)-M12

Unit: mm

Chapter 1: Product Introductions

Chapter 2

Switches and Connectors

RCO-3200 | User’s Manual

38

2.1 Switch and Connector Locations

2.1.1 Top View

Chapter 2: Switches and Connectors

RCO-3200 | User’s Manual

39

2.1.2 Bottom View

Chapter 2: Switches and Connectors

RCO-3200 | User’s Manual

40

2.2 Connector / Switch Definition

List of Connector / Switch

Chapter 2: Switches and Connectors

Connector Location Definition

AT_ATX

1

AT

/ ATX Power Mode Switch

CLR_CMOS

1

Clear

BIOS Switch

CAR_PWR

1

PC / Car

Mode Switch

DELAY_TIME

1

Car

mode PC turn off delay time

CFAST

1_1

CFast

Socket

PWR_SW

1

Power

Switch

RESET

1

Reset

Switch

USB

1_2_1

USB 3.0 Port

USB

3_4_1

USB 2.0 Port

SIM

1_1, SIM2_1

SIM

Card Socket

COM1_1

, COM2_1

RS232

/ RS422 / RS485 Connector

COM3_2, COM4_2, COM5_2, COM6_1

RS232 / RS422 / RS485 Connector

LAN

1, LAN2

LAN Port

LAN

3, LAN4, LAN5, LAN6, LAN7, LAN8,

LAN

9, LAN10

LAN Port / M12 LAN Port

DC_IN

1

3

-pin DC 9~50V Power Input Connector

DVI

-I1

DVI

-I Connector

DP1

DisplayPort

Connector

LINE_OUT1

Line

-out Jack

MIC_IN1

Mic

-in Jack

DIO1

8DI

/ 8DO Connector

PWR_SW2

Remote

Power Switch

MINI

-PCIE1

Mini PCI

-Express / mSATA Socket

MINI

-PCIE2

Mini PCI

-Express Socket

SATA1_1, SATA2

SATA

with Power Connector

PCIE1

PCI

-Express X4 Slot (1-lane)

PWR_LED1

Power LED Status

HDD_LED1

HDD Access LED Status

LAN1_LINK1,

LAN2_LINK1

LAN

Link LED

LAN1_ACT1, LAN2_ACT1

LAN

Active LED

GPIO_LED1

GPIO LED Status

WDT_LED1

Watchdog LED Status

RCO-3200 | User’s Manual

Switch Definition

1-2 (Right)

ATX Power Mode

（Default）

2-3 (Left)

AT Power Mode

41

2.3 Switches Definitions

AT_ATX1: AT / ATX Power Mode Switch

CLR_CMOS1: Clear BIOS Switch

Switch Definition

Off Normal Status (Default)

ON Clear BIOS

Chapter 2: Switches and Connectors

Switch Definition

1-2 (Right)

PC

Power Mode（Default）

2-3 (Left)

Power Ignition Mode

CAR_PWR1: PC / Car Mode Switch

Switch 1 / 2 / 3 Definition

ON / ON / ON

3 sec.

（Default Shutdown Timer by O.S）

ON / ON / OFF

1 min.

ON / OFF / ON

5 min.

ON / OFF / OFF

10 min.

OFF / ON / ON

30 min.

OFF / ON / OFF

1 hour

OFF / OFF / ON

2 hour

DELAY_TIME1: Power off delay time setup Switch

RCO-3200 | User’s Manual

Chapter 2: Switches and Connectors

Step of Setting Power Ignition

Step 1:
To select power ignition by PC/CAR switch.

Step 2:
To configure the power off delay time, please check the Delay Time Setting Options in
advance.

Step 3:
To connect the power and ignition power

Example: Delay Time Setting for 5 minutes

1. If delay time set as “5 minutes”

2. The system will shut down 5 minutes later after turning off the vehicle.

Step 1
Pin 1-2 (Right): PC Mode
Pin 2-3 (Left): Power Ignition Mode

Switch 1 / 2 / 3 Power off delay time

ON / ON / ON

3 second

ON / ON / OFF

1 minute

ON / OFF / ON

5 minutes

ON / OFF / OFF

10 minutes

OFF / ON / ON

30 minutes

OFF / ON / OFF

1 hour

OFF / OFF / ON

2 hours

Step 3

Step 3
To connect the battery power and

ignition signal

RCO-3200 | User’s Manual

43

2.4 Connectors Definitions

Chapter 2: Switches and Connectors

43

CFAST1_1: CFast Socket

Chapter 2: Switches and Connectors

Pin Definition Pin Definition Pin Definition

S1 GND PC1 NC PC10 NC

S2 SATA_TXP1 PC2 GND PC11 NC

S3 SATA_TXN1 PC3 NC PC12 NC

S4 GND PC4 NC PC13 +3.3V

S5 SATA_RXN1 PC5 NC PC14 +3.3V

S6 SATA_RXP1 PC6 NC PC15 GND

S7 GND PC7 GND PC16 GND

PC8 NC PC17 NC

PC9 NC

PWR_SW1: Power Button

Pin Definition Pin Definition

1 NC 4 GND
2

Power Button

5 NC

3 NC 6 GND

RESET1 : Reset Button

Pin Definition

1 RESET
2 GND

USB1_2_1: USB3.0 Connector, Type A

Pin Definition Pin Definition

1 +5V 10 +5V

2 USB2_D0- 11 USB2_D1-

3 USB2_D0+ 12 USB2_D1+

4 GND 13 GND

5 USB3_RX0- USB3_RX1-

6 USB3_RX0+ USB3_RX1+

7 GND GND

8 USB3_TX0- USB3_TX1-

9 USB3_TX0+ USB3_TX1+

RCO-3200 | User’s Manual

44

Chapter 2: Switches and Connectors

44

Chapter 2: Switches and Connectors

USB3_4_1: USB2.0 Connector, Type A

Pin USB3_4_1 Definition

1 +5V

2 USB2_D2-

3 USB2_D2+

4 GND

5 +5V

6 USB2_D3-

7 USB2_D3+

8 GND

SIM1_1, SIM2_1：SIM Card Socket

Pin Definition Pin Definition

C1 UIM_PWR C6 UIM_VPP

C2 UIM_RESET C7 UIM_DATA

C3 UIM_CLK CD NC

C5 GND COM GND

RCO-3200 | User’s Manual

45

Chapter 2: Switches and Connectors

45

COM1_1: RS232 / RS422 / RS485 Connector

Connector Type: 9-pin D-Sub

Pin RS232 Definition

RS422 / 485 Full

Duplex Definition

RS485 Half Duplex

Definition

1 DCD1 TX1- DATA1-

2 RXD1 TX1+ DATA1+

3 TXD1 RX1+

4 DTR1 RX1-

5 GND GND GND

6 DSR1

7 RTS1

8 CTS1

9 RI1

COM2_1: RS232 / RS422 / RS485 Connector

Connector Type: 9-pin D-Sub

Pin RS232 Definition

RS422 / 485 Full

Duplex Definition

RS485 Half Duplex

Definition

1 DCD2 TX2- DATA2-

2 RXD2 TX2+ DATA2+

3 TXD2 RX2+

4 DTR2 RX2-

5 GND GND GND

6 DSR2

7 RTS2

8 CTS2

9 RI2

RCO-3200 | User’s Manual

46

Chapter 2: Switches and Connectors

46

COM3_2： RS232 / RS422 / RS485 Connector

Connector Type: 2X5 10-pin box header, 2.54mm pitch

COM3_1

Pin RS232 Definition

RS422 / 485 Full

Duplex Definition

RS485 Half Duplex

Definition

1 DCD3 TX3- DATA3-

2 RXD3 TX3+ DATA3+

3 TXD3 RX3+

4 DTR3 RX3-

5 GND GND GND

6 DSR3

7 RTS3

8 CTS3

9 RI3

COM4_2： RS232 / RS422 / RS485 Connector

Connector Type: 2X5 10-pin box header, 2.54mm pitch

COM4_1

Pin RS232 Definition

RS422 / 485 Full

Duplex Definition

RS485 Half Duplex

Definition

1 DCD4 TX4- DATA4-

2 RXD4 TX4+ DATA4+

3 TXD4 RX4+

4 DTR4 RX4-

5 GND GND GND

6 DSR4

7 RTS4

8 CTS4

9 RI4

RCO-3200 | User’s Manual

47

Chapter 2: Switches and Connectors

47

COM5_2： RS232 / RS422 / RS485 Connector

Connector Type: 2X5 10-pin box header, 2.54mm pitch

COM3_1

Pin RS232 Definition

RS422 / 485 Full

Duplex Definition

RS485 Half Duplex

Definition

1 DCD5 TX5- DATA5-

2 RXD5 TX5+ DATA5+

3 TXD5 RX5+

4 DTR5 RX5-

5 GND GND GND

6 DSR5

7 RTS5

8 CTS5

9 RI5

COM6_1： RS232 / RS422 / RS485 Connector

Connector Type: 2X5 10-pin box header, 2.54mm pitch

COM4_1

Pin RS232 Definition

RS422 / 485 Full

Duplex Definition

RS485 Half Duplex

Definition

1 DCD6 TX6- DATA6-

2 RxD6 TX6+ DATA6+

3 TxD6 RX6+

4 DTR6 RX6-

5 GND GND GND

6 DSR6

7 RTS6

8 CTS6

9 RI6

RCO-3200 | User’s Manual

48

Chapter 2: Switches and Connectors

48

LAN1, LAN2: RJ45 with LEDs Port

Connector Type: RJ45 Connector

Pin Definition Pin Definition

1 LAN1_MDI0P 5 LAN1_MDI2N
2 LAN1_MDI0N 6 LAN1_MDI1N
3 LAN1_MDI1P 7 LAN1_MDI3P
4 LAN1_MDI2P 8 LAN1_MDI3N

Pin Definition Pin Definition

1 LAN2_MDI0P 5 LAN2_MDI2N

2 LAN2_MDI0N 6 LAN2_MDI1N

3 LAN2_MDI1P 7 LAN2_MDI3P

4 LAN2_MDI2P 8 LAN2_MDI3N

Link LED Status Definition Act LED Status Definition

Steady Orange 1Gbps Network Link Blinking Yellow Data Activity

Steady Green 100Mbps Network Link Off No Activity

Off 10Mbps Network Link

LAN3, LAN4, LAN5, LAN6, LAN7, LAN8, LAN9, LAN10: RJ45 with LEDs Port

Connector Type: RJ45 Connector

Pin

LAN3~LAN6

Definition

Pin

LAN3~LAN6

Definition

1 LAN_MDI0P 5 LAN_MDI2N
2 LAN_MDI0N 6 LAN_MDI1N
3 LAN_MDI1P 7 LAN_MDI3P
4 LAN_MDI2P 8 LAN_MDI3N

Link LED Status LAN3~LAN6 Definition Act LED Status LAN3~LAN6 Definition

Steady Orange 1Gbps Network Link Blinking Yellow Data Activity

Steady Green 100Mbps Network Link Off No Activity

Off 10Mbps Network Link

RCO-3200 | User’s Manual

49

Chapter 2: Switches and Connectors

49

DC_IN1: DC Power Input Connector (+9~50V)

Connector Type: Terminal Block 1X3 3-pin, 5.0mm pitch

Pin Definition

1 +9~50VIN
2 Power Ignition

3 GND

LAN3, LAN4, LAN5, LAN6, LAN7, LAN8, LAN9, LAN10: M12 Lan Port

Connector Type: M12 X-code Female Connector

Pin

LAN3~LAN6

Definition

Pin

LAN3~LAN6

Definition

1 LAN_MDI0P 5 LAN_MDI3N

2 LAN_MDI0N 6 LAN_MDI3N
3 LAN_MDI1P 7 LAN_MDI2P
4 LAN_MDI1N 8 LAN_MDI2N

DVI-I1: DVI-I Connector

Pin Definition Pin Definition

1 DVI_TX2- 16 DVI Hot Plug Detect
2 DVI_TX2+ 17 DVI_TX0­3 GND 18 DVI_TX0+
4 NC 19 GND
5 NC 20 VGA_DDC_CLOCK

6 DVI_DDC_CLOCK 21 VGA_DDC_DATA

7 DVI_DDC_DATA 22 GND
8 VGA VSYNC 23 DVI_TXCLK+

9 DVI_TX1- 24 DVI_TXCLK­10 DVI_TX1+ C1 VGA_RED
11 GND C2 VGA_GREEN
12 NC C3 VGA_BLUE
13 NC C4 VGA_HSYNC
14 +5V C5 GND
15 GND

RCO-3200 | User’s Manual

50

Chapter 2: Switches and Connectors

DP1: DisplayPort Connector

Pin Definition Pin Definition

1 DP_LANE0_P 11 GND
2 GND 12 DP_LANE3_N
3 DP_LANE0_N 13 GND
4 DP_LANE1_P 14 GND

5 GND 15 DP_AUX_P

6 DP_LANE1_N 16 GND
7 DP_LANE2_P 17 DP_AUX_N
8 GND 18 DP_HPD
9 DP_LANE2_N 19 GND

10 DP_LANE3_P 20 DP_PWR

LINE_OUT1 : Line-out Jack (Green)

Connector Type: 5-pin Phone Jack

Pin Definition

1 GND
2 OUT_R
3 NC
4 GND
5 OUT_L

MIC_IN1: Microphone Jack (Pink)

Connector Type: 5-pin Phone Jack

Pin Definition

1 GND
2 MIC_R
3 NC
4 GND
5 MIC_L

RCO-3200 | User’s Manual

51

Chapter 2: Switches and Connectors

DIO1: Digital Input / Output Connector

Connector Type: Terminal Block 2X9 18-pin, 3.5mm pitch

Pin Definition Pin Definition

1 DI1 2 DO1

3 DI2 4 DO2

5 DI3 6 DO3

7 DI4 8 DO4

9 DI5 10 DO5

11 DI6 12 DO6

13 DI7 14 DO7

15 DI8 16 DO8

17 External DC INPUT 18 External GND

RCO-3200 | User’s Manual

52

Chapter 2: Switches and Connectors

PWR_SW2 : Remote Power Switch

Connector Type: Terminal Block 1X2 2-pin, 3.5mm pitch

Pin Definition

1 Power Button
2 GND

RCO-3200 | User’s Manual

53

Chapter 2: Switches and Connectors

MINIPCIE1: Mini PCI-Express / mSATA Socket

MINIPCIE2: Mini PCI-Express

Pin

Definition

Pin

Definition

Pin

Definition

1 WAKE# 19 NC 37 GND
2 +3.3V 20 +3.3V 38 USB_D5+

3 NC 21 GND 39 +3.3V

4 GND 22 PCIE RST# 40 GND

5 NC 23

PCIE_RXN3

(SATA_RXN1)

41 +3.3V

6 +1.5V 24 +3.3V 42 NC

7 CLKREQ3# 25

PCIE_RXP3

(SATA_RXP1)

43 GND

8 USIM1_VCC 26 GND 44 NC

9 GND 27 GND 45 NC
10 USIM1_DATA 28 +1.5V 46 NC
11 PCIE_CLKN3 29 GND 47 NC
12 USIM1_CLK 30 SMB_CLK 48 +1.5V

13 PCIE_CLKP3 31

PCIE_TXN3

(SATA_TXN1)

49 NC

14 USIM1_RST 32 SMB_DATA 50 GND

15 GND 33

PCIE_TXP3

(SATA_TXP1)

51 NC

16 USIM1_VPP 34 GND 52 +3.3V
17 NC 35 GND
18 GND 36 USB_D5-

Pin

Definition

Pin

Definition

Pin

Definition

1 WAKE# 19 NC 37 GND

2 +3.3V 20 +3.3V 38 USB_D6+

3 NC 21 GND 39 +3.3V

4 GND 22 MINIPCIE RST# 40 GND

5 NC 23 PCIE_RXN4 41 +3.3V

6 +1.5V 24 +3.3V 42 NC

7 CLKREQ4# 25 PCIE_RXP4 43 GND

8 USIM2_VCC 26 GND 44 NC

9 GND 27 GND 45 NC
10 USIM2_DATA 28 +1.5V 46 NC
11 PCIE_CLKN4 29 GND 47 NC

12 USIM2_CLK 30 SMB_CLK 48 +1.5V
13 PCIE_CLKP4 31 PCIE_TXN4 49 NC
14 USIM2_RST 32 SMB_DATA 50 GND

15 GND 33 PCIE_TXP4 51 NC
16 USIM2_VPP 34 GND 52 +3.3V
17 NC 35 GND
18 GND 36 USB_D6-

RCO-3200 | User’s Manual

54

Chapter 2: Switches and Connectors

SATA1_1, SATA2: SATA with Power Connector

Pin

SATA1_1

Definition

Pin

SATA1_1

Definition

Pin

SATA2

Definition

Pin

SATA2

Definition

1 GND 12 GND 1 GND 12 GND

2

SATA_TXP0

13 GND 2 SATA_TXP1 13 GND

3

SATA_TXN0

14 +5V 3

SATA_TXN1

14 +5V
4 GND 15 +5V 4 GND 15 +5V
5

SATA_RXN0

16 +5V 5

SATA_RXN1

16 +5V
6

SATA_RXP0

17 GND 6

SATA_RXP1

17 GND
7 GND 18 GND 7 GND 18 GND
8 +3.3V 19 GND 8 +3.3V 19 GND
9 +3.3V 20 +12V 9 +3.3V 20 +12V

10 +3.3V 21 +12V 10 +3.3V 21 +12V
11 GND 22 +12V 11 GND 22 +12V

Pin Definition Pin Definition Pin Definition Pin Definition

A1

PCIE_PRSNT1

A17

PCIE_RXN4

B1 +12V B17 PRSNT2_1
A2 +12V A18 GND B2 +12V B18 GND
A3 +12V A19 B3 +12V B19
A4 GND A20 B4 GND B20
A5 NC A21 B5 SMB_CLK B21
A6 NC A22 B6 SMB_DATA B22
A7 NC A23 B7 GND B23
A8 NC A24 B8 +3.3V B24
A9 +3.3V A25 B9 NC B25

A10

+3.3V A26 B10 +3.3VSB B26

A11

PCIE_RESET# A27 B11 PCIE_WAKE# B27

A12

GND A28 B12 NC B28

A13

PCIE_CLKP A29 B13 GND B29

A14

PCIE_CLKN A30 B14 PCIE_TXP4 B30

A15

GND A31 B15 PCIE_TXN4 B31

A16

PCIE_RXP4 A32 B16 GND B32

PCIE1: PCI-Express X4 Socket (1-lane)

Connector Type: PCI-Express X4 Slot

RCO-3200 | User’s Manual

55

Chapter 2: Switches and Connectors

PWR_LED1: Power LED Status

Pin Definition

1 POWER LED+
2 POWER LED-

Pin Definition

1 HDD LED+
2 HDD LED-

HDD_LED1: HDD Access LED Status

Pin Definition

1 WATCHDOG LED+
2 WATCHDOG LED-

WDT_LED1: Watchdog LED Status

Pin Definition

1 GPIO LED+
2 GPIO LED-

GPIO_LED1: GPIO LED Status

Pin Definition

1 LINK LED+
2 LINK LED-100Mbps­3 LINK LED 100Mbps-

LAN1_LINK1, LAN2_LINK1 : LAN Link LED Status

Pin Definition

1 ACTIVE LED+
2 ACTIVE LED-

LAN1_ACT1, LAN2_ACT1 : LAN Active LED Status

Chapter 3

System Setup

RCO-3200 | User’s Manual

3.1 Set torque force to 3.5 kgf-cm to execute all the screwing and

unscrewing.

3.2 Removing chassis bottom cover

1. Turn the system upside down. Unscrew the six screws (M3x5L) on the bottom cover.

2. Now you can remove the bottom cover.

57

Chapter 3: System Setup

In order to prevent electric shock or system damage, before removing the
chassis cover, must turn off power and disconnect the unit from power source.

WARNING

RCO-3200 | User’s Manual

3.3 Removing PCIe/PCI expansion module

1. This step only applies to RCO-3211 and RCO-3222 series, which is equipped with PCIe/PCI
expansion module. The following steps use RCO-3222 as example.

2. Unscrew four screws (M3x5L) circled below.

3. Now you can remove the PCIe/PCI expansion module.

58

Chapter 3: System Setup

RCO-3200 | User’s Manual

3.4 Installing SODIMM

1. Unscrew the below three screws to remove the HDD bracket.

2. After removing internal SATA HDD bracket, you will be able to access the memory slot.

59

Chapter 3: System Setup

RCO-3200 | User’s Manual

3. Insert memory module from 45 degree direction.

4. Press the memory module vertically downward until you hear the “click” sound. Make sure
the memory module is firmly in place.

60

Chapter 3: System Setup

RCO-3200 | User’s Manual

3.5 Installing mini PCIe card / mSATA

1. Two mini PCIe slots are available for RCO-3200 series. MiniPCIE1 supports mSATA.

2. Insert mini PCIe card or mSATA module from 45 degree direction.

3. Press the mini PCIe card or mSATA module down and lock it with two screws (M2x3.7L).

61

Chapter 3: System Setup

MiniPCIE1 / mSATA

MiniPCIE2

RCO-3200 | User’s Manual

3.6 Installing antenna

1. Four antenna holes are available for RCO-3200 series on the rear panel.

2. Remove antenna hole cover on the system panel.

3. Have antenna jack penetrate through the hole.

62

Chapter 3: System Setup

RCO-3200 | User’s Manual

4. Put on washer and fasten the nut with antenna jack.

5. Assemble the antenna and antenna jack together.

6. Attach the RF connector at the cable-end onto the communication module.

63

Chapter 3: System Setup

RCO-3200 | User’s Manual

3.7 Installing HDD on internal SATA HDD bay

1. Unscrew the below three screws (M3x5L) to remove the internal SATA HDD bay.

2. Lock the 2.5” HDD with HDD bracket using four screws (M3x4L).

64

Chapter 3: System Setup

RCO-3200 | User’s Manual

3. Install the HDD bracket following the direction below.

4. Fasten the three screws to lock the internal HDD bracket.

65

Chapter 3: System Setup

RCO-3200 | User’s Manual

3.8 Installing HDD on removable SATA HDD bay

1. Unscrew the two sun screws circled below to take out the removable SATA HDD bay.

2. Lock the 2.5” HDD with HDD bracket using four screws (M3x4L).

3. Slide the HDD bracket back and then fasten the sun screws.

66

Chapter 3: System Setup

RCO-3200 | User’s Manual

3.9 Installing PCIe/PCI expansion card

1. PCIe or PCI card with FHHL dimension is supported by RCO-3200 series.

2. Unscrew the screw (M3x5L) to remove the plane bracket.

3. Loose the sun screw (circled below) on the holder so the pairing arm can be adjustable.

67

Chapter 3: System Setup

RCO-3200 | User’s Manual

4. Install the PCIe/PCI card according to the below direction and ensure the gold finger is
inserted into the slot. Then fasten the screw in the circle.

5. Adjust the arm until it holds the card firmly in place. Then fasten the sun screw on the holder.

6. For RCO-3022 series, install the upper card (Card 1) first and then install the lower card (Card

2).

68

Chapter 3: System Setup

Card 1

Card 2

RCO-3200 | User’s Manual

3.10 Assemble PCIe/PCI expansion module

1. Install the expansion module back in place and ensure the golden finger is inserted into the
expansion slot.

2. Fasten the four screws (M3x5L) below.

69

Chapter 3: System Setup

RCO-3200 | User’s Manual

3.11 Assemble chassis bottom cover

1. Place the bottom cover according to the below direction and make sure the rail is facing
inside the system.

2. Lock the bottom cover with the six screws (M3x5L).

70

Chapter 3: System Setup

RCO-3200 | User’s Manual

3.12 Assemble SIM card

1. Take out the removable SATA HDD bay in order to locate the SIM card slot.

2. Now you can insert SIM card into the socket.

3. Please note that the installation of SIM 1 and SIM 2 has to match the installation of mini
PCIe slots.

4. To uninstall SIM card, simply press the installed SIM card and then the card will be pushed
out.

71

Chapter 3: System Setup

SIM1

SIM2

SIM Card Socket Number

Matching Mini PCIe Slot

SIM 1 Mini PCIe 1 / mSATA (CN1)

SIM 2 Mini PCIe 2 (CN2)

RCO-3200 | User’s Manual

3.13 Installing wall mount kit

1. Wall mount kit is available for RCO-3000 series included in the standard package.

2. Place the system upside down so you can see the bottom cover. The highlighted screw holes
below will be used.

3. Lock the wall mount kit with eight screws (M3x5L, Nylok).

72

Chapter 3: System Setup

RCO-3200 | User’s Manual

3.14 Installing DIN rail holder

1. Din rail holder is available for RCO-3000 series as optional accessories.

2. Place the system upside down so you can see the bottom cover with two screw holes for din
rail holder.

3. Place the din rail holder on top of the bottom cover and lock it with two screws (M4x5L,

Nylok).

73

Chapter 3: System Setup

Chapter 4

BIOS Setup

RCO-3200 | User’s Manual

75

4.1 BIOS Introduction

The system BIOS software is stored on EEPROM. The BIOS provides an interface to modify the
configuration. When the battery is removed, all the parameters will be reset.

BIOS Setup

Power on the embedded system and by pressing <Del> or <F2> immediately allows you to enter
the setup screens. If the message disappears before you respond and you still wish to enter the
Setup, restart the system by turning it OFF and ON or pressing the RESET button.
You may also restart the system by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys.

Main Setup

The main menu lists the setup functions you can make changes to. You can use the arrow keys
( ↑↓ ) to select the item. The on-line description of the highlighted setup function is displayed
at the bottom of the screen.

General Help <F1>

The BIOS setup program provides a General Help screen. You can call up this screen from any
menu by simply pressing <F1>. The Help screen lists the appropriate keys to use and the possible
selections for the highlighted item. Press <Esc> to exit the Help screen.

Chapter 4: BIOS Setup

Control Keys

<→> <←>

Select Screen

<↑> <↓>

Select Item

<Enter>

Select

<Page Up/+>

Increases the numeric value or makes changes

<Page Down/

->

Decreases the numeric value or makes changes

<F1>

General Help

<F2>

Previous Value

<F3>

Load Optimized Defaults

<F4>

Save Configuration and Exit

<Tab>

Select Setup Fields

<Esc>

Exit BIOS Setup

RCO-3200 | User’s Manual

76

4.2 Main Setup

Press <Del> to enter BIOS CMOS Setup Utility. The Main setup screen is showed as following
when the setup utility is entered. System Date/Time is set up in the Main Menu.

4.2.1 System Date

Set the system date. Please use <Tab> to switch between data elements.

4.2.2 System Time

Set the system time. Please use <Tab> to switch between time elements.

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

4.3 Advanced Setup

4.3.1 Trusted Computing (Optional)

■ Security Device Support

Enable or disable TPM function

77

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

4.3.2 ACPI Settings

■ Enable ACPI Auto Configuration

This item allows you to enable or disable BIOS ACPI Auto Configuration.

■ Enable Hibernation

This item allows you to enable or disable system ability to hibernate.

■ ACPI Sleep State

This item selects the highest ACPI sleep state the system will enter when the suspend button is
pressed. Select <Suspend Disabled> or <S3 (Suspend to RAM)>.

4.3.3 Super IO Configuration

This setting allows you to select options for the Super IO Configuration, and change the value of
the selected option.

78

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

■ Serial Port 1 Configuration

⚫ Serial Port

This item allows you to enable or disable serial port.

⚫ Change Settings

This item allows you to change the address & IRQ settings of the specified serial port.

⚫ Device Type Select

Change the Serial interface. Select <RS232> ,<RS422 Full Duplex> or <RS485 Half Duplex> interface.

■ Serial Port 2 Configuration

⚫ Serial Port

This item allows you to enable or disable serial port.

⚫ Change Settings

This item allows you to change the address & IRQ settings of the specified serial port.

⚫ Device Type Select

Change the Serial interface. Select <RS232> ,<RS422 Full Duplex> or <RS485 Half Duplex> interface.

79

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

■ Serial Port 3 Configuration

⚫ Serial Port

This item allows you to enable or disable serial port.

⚫ Change Settings

This item allows you to change the address & IRQ settings of the specified serial port.

⚫ Device Type Select

Change the Serial interface. Select <RS232> ,<RS422 Full Duplex> or <RS485 Half Duplex> interface.

■ Serial Port 4 Configuration

⚫ Serial Port

This item allows you to enable or disable serial port.

⚫ Change Settings

This item allows you to change the address & IRQ settings of the specified serial port.

⚫ Device Type Select

Change the Serial interface. Select <RS232> ,<RS422 Full Duplex> or <RS485 Half Duplex> interface.

80

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

■ Serial Port 5 Configuration

⚫ Serial Port

This item allows you to enable or disable serial port.

⚫ Change Settings

This item allows you to change the address & IRQ settings of the specified serial port.

⚫ Device Type Select

Change the Serial interface. Select <RS232> ,<RS422 Full Duplex> or <RS485 Half Duplex> interface.

■ Serial Port 6 Configuration

⚫ Serial Port

This item allows you to enable or disable serial port.

⚫ Change Settings

This item allows you to change the address & IRQ settings of the specified serial port.

⚫ Device Type Select

Change the Serial interface. Select <RS232> ,<RS422 Full Duplex> or <RS485 Half Duplex> interface.

81

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

■ Watch Dog Function

This setting allows you to setup the system watch-dog timer, a hardware timer that generates a

reset when the software that it monitors does not respond as expected each time the watch

dog polls it.

⚫ Watch Dog Timer Count Mode

Change the Watch dog mode. Select <Second Mode> or <Minute Mode> mode.

⚫ Watch Dog Timer Time Out Value

User can set a value in the range of 20 to 255.

4.3.4 Hardware Monitor

These items display the current status of all monitored hardware devices/ components such as
voltages and temperatures.

82

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

4.3.5 Serial Port Console Redirection

■ Console Redirection

These items allows you to enable or disable COM1 console redirection.

4.3.6 CPU Configuration

■ Intel Virtualization Technology

Virtualization enhanced by Intel Virtualization Technology will allow a platform to run multiple
operating systems and applications in independent partitions. With virtualization, one
computer system can function as multiple Virtual systems.

83

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

4.3.7 Network Stack Configuration

■ Network Stack

This item allows you to enable or disable UEFI network stack.

⚫ IPv4 PXE Support

This item allows you to enable or disable IPv4 PXE Support. t. This item is configurable only
when Network Stack is enabled.

⚫ IPv4 HTTP Support

This item allows you to enable or disable HTTP boot support for IPv4. This item is
configurable only when Network Stack is enabled.

⚫ Ipv6 PXE Support

This item allows you to enable or disable IPv6 PXE Support. t. This item is configurable only
when Network Stack is enabled.

⚫ IPv6 HTTP Support

This item allows you to enable or disable HTTP boot support for IPv4. This item is
configurable only when Network Stack is enabled.

⚫ PXE boot wait time

This item allows you to configure how long to wait before you can press to abort the PXE
boot. This item is configurable only when Network Stack is enabled.

⚫ Media detect count

This item allows you to set the number of times to check the presence of media. This item is
configurable only when Network Stack is enabled.

84

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

4.3.8 CSM Configuration

■ CSM Support

Enables or disables UEFI CSM (Compatibility Support Module) to support a legacy PC boot
process.

■ Boot option filter

This item allows you to select which type of operating system to boot.
UEFI and Legacy: Allows booting from operating systems that support legacy option ROM or
UEFI option ROM.
Legacy only: Allows booting from operating systems that only support legacy option ROM.
UEFI only: Allows booting from operating systems that only support UEFI option ROM.
This item is configurable only when CSM Support is set to Enabled.

■ PXE Function

This item allows you to enable or disable PXE function.

■ Storage

This setting allows you to select whether to enable the UEFI or legacy option ROM for the
storage device controller.
Do not launch: Disables option ROM.
UEFI only: Enables UEFI option ROM only.
Legacy only: Enables legacy option ROM only.

■ Video

This item allows you to select whether to enable the UEFI or legacy option ROM for the storage

device controller.

Do not launch: Disables option ROM.
UEFI only: Enables UEFI option ROM only.
Legacy only: Enables legacy option ROM only.

85

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

4.3.9 SATA Configuration

■ SATA Port 0

This item allows you to enable or disable SATA Port 0.

■ SATA Port 0 Hot Plug Capability

This item allows you to enable or disable SATA Port 0 hot plug function.

■ SATA Port 1/mSATA/CFast

This item allows you to enable or disable SATA Port 1.

86

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

4.3.10 USB Configuration

■ Legacy USB Support

Allows USB keyboard/ mouse to be used in MS-DOS.

■ XHCI Hand-off

Determines whether to enable XHCI (USB3.0) Hand-off feature for an operating system without
XHCI (USB3.0) Hand-off support.

■ USB Mass Storage Driver Support

Enables or disables support for USB storage devices.

87

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

4.4 Chipset

4.4.1 North Bridge

This section provides information on the installed memory size and memory/onboard graphics­related configuration options.

88

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

■ Intel IGD Configuration

This section provides onboard graphics-related configuration options.

⚫ Aperture Size

This item selects the Aperture Size. Select <128MB>, <256MB> or <512MB>.

⚫ DVMT Pre-Allocated

This item selects DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the

Internal Graphics Device. . Select <64M>, <96M>, <128M>, <160M>, <192M>, <224M>,

<256M>, <288M>, <320M>, <352M>, <384M>, <416M>, <448M>, <480M> or <512M>.

⚫ DVMT Total Gfx Mem

This item selects DVMT5.0 Total Graphic Memory size used by the Internal Graphics Device.
Select <128MB>, <256MB> or <Max>.

■ Primary IGFX Boot Display

Change the primary IGFX boot display. Select <Auto>, <DP>, <VGA> or <DVI>.

89

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

4.4.2 South Bridge

■ HD-Audio Configuration

Control detection of the HD-Audio.

⚫ HD-Audio Support

Enabled: HD-Audio will be unconditionally enabled.
Disabled: HD-Audio will be unconditionally disabled.

90

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

■ PCI Express Configuration

⚫ PCI Express Port 1 (I210 lan1)

This item allows you to enable or disable PCI Express Port 1 (I210 lan1) in the Chipset.

⚫ Speed

Change the PCIe Port Speed. Select <AUTO> ,<Gen 1> or <Gen 2>

⚫ PCI Express Port 2 (I210 lan2)

This item allows you to enable or disable PCI Express Port 2 (I210 lan2) in the Chipset.

⚫ Speed

Change the PCIe Port Speed. Select <AUTO> ,<Gen 1> or <Gen 2>

⚫ PCI Express Port 3 (4LAN_L/mPCIE1)

This item allows you to enable or disable PCI Express Port 3 (4LAN_L/mPCIE1) in the Chipset.

⚫ Speed

Change the PCIe Port Speed. Select <AUTO> ,<Gen 1> or <Gen 2>

⚫ PCI Express Port 4 (4LAN_R/mPCIE2/Riser)

This item allows you to enable or disable PCI Express Port 4 ((4LAN_R/Mpcie2/Riser) in the
Chipset.

⚫ Speed

Change the PCIe Port Speed. Select <AUTO> ,<Gen 1> or <Gen 2>

■ Restore AC Power Loss

This item specifies whether your system will reboot after a power failure or interrupt occurs.
Available settings are:
Power Off: Leave the computer in the power off state.

Power On: Leave the computer in the power on state.

Last State: Restore the system to the previous status before power failure or interrupt occurred.

91

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

4.5 Security

Security menu allow you to change administrator password and user password settings.

4.5.1 Administrator Password

This item allows you to set Administrator Password.

4.5.2 User Password

This item allows you to set User Password.

92

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

4.6 Boot

This menu allows you to setup the system boot options.

4.6.1 Setup Prompt Timeout

This item sets number of seconds to wait for setup activation key.

4.6.2 Bootup NumLock State

This item selects the keyboard NumLock state. Select <On> or <Off>.

4.6.3 Full Screen Logo Show

This item allows you to enable or disable Full Screen Logo Show function.

4.6.4 Boot Option Priorities

The items specify the boot device priority sequence from the available devices. The number of
device items that appears on the screen depends on the number of devices installed in the
system.

93

Chapter 4: BIOS Setup

RCO-3200 | User’s Manual

4.7 Save & Exit

This setting allows you to configure the boot settings.

4.7.1 Save Changes and Reset

This item allows you reset the system after saving the changes.

4.7.2 Discard Changes and Reset

Select this option to quit Setup without making any permanent changes to the system
configuration.

4.7.3 Restore Defaults

This selection allows you to reload the BIOS when problem occurs during system booting
sequence. These configurations are factory settings optimized for this system.

94

Chapter 4: BIOS Setup

Appendix

WDT & GPIO

This appendix provides the sample codes of WDT (Watch
Dog Timer) and GPIO (General Purpose Input/ Output).

RCO-3200 | User’s Manual

96

WDT Sample Code

SIO_INDEX_Port equ 04Eh
SIO_DATA_Port equ 04Fh

SIO_UnLock_Value equ 087h

SIO_Lock_Value equ 0AAh
WatchDog_LDN equ 007h
WDT_UNIT equ 60h ;60h=second, 68h=minute, 40h=Disabled Watchdog timer
WDT_Timer equ 30 ;ex. 30 seconds

Sample code:
;Enable config mode

mov dx, SIO_INDEX_Port
mov al, SIO_UnLock_Value
out dx, al
jmp short $+2 ;Io_delay
jmp short $+2 ;Io_delay

out dx, al

;Change to WDT

mov dx, SIO_INDEX_Port
mov al, 07h
out dx, al
mov dx, SIO_DATA_Port
mov al, WatchDog_LDN
out dx, al

;Acive WDT

mov dx, SIO_INDEX_Port
mov al, 30h
out dx, al
mov dx, SIO_DATA_Port

in al, dx

or al, 01h
out dx, al

;set timer

mov dx, SIO_INDEX_Port
mov al, 0F6h
out dx, al
mov dx, SIO_DATA_Port

mov al, WDT_Timer

out dx, al

;set UINT

mov dx, SIO_INDEX_Port
mov al, 0F5h
out dx, al
mov dx, SIO_DATA_Port

mov al, WDT_UNIT

out dx, al

;enable reset

mov dx, SIO_INDEX_Port
mov al, 0Fah
out dx, al
mov dx, SIO_DATA_Port
in al, dx
or al, 01h
out dx, al

;close config mode

mov dx, SIO_INDEX_Port
mov al, SIO_Lock_Value
out dx, al

Appendix – WDT & GPIO

RCO-3200 | User’s Manual

97

GPIO Sample Code

⚫ GPI 0 ~ GPI 3

⚫ GPO 0 ~ GPO 3

GPI_REG equ 0A03h
GPO_REG equ 0A02h
GPO_0 equ 00000001b

____________________________________________________________________________________

Sample Code:

#1 : Get GPI 0 status

; Get GPI 0 Pin Status Register

In al, GPI_REG

;al bit4 = GPI 0 status

#2 : Set GPO 0 status to high

; Set GPO 0 Pin to High

mov dx, GPO_REG
in al, dx
or al, GPO_0

out dx, al

;al bit0 = GPO 0 status

Appendix – WDT & GPIO

GPI 0 GPI 1 GPI 2 GPI 3

IO Address 0xA03h 0xA03h 0xA03h 0xA03h

Bit 4 5 6 7

Sample code #1

GPO 0 GPO 1 GPO 2 GPO 3

IO Address 0xA02h 0xA02h 0xA02h 0xA02h

Bit 0 1 2 3

Sample code #2

RCO-3200 | User’s Manual

98

⚫ GPI 4 ~ GPI 7

⚫ GPO 4 ~ GPO 7

GPI_REG equ 0A06h
GPO_REG equ 0A06h
GPO_4 equ 00010000b

____________________________________________________________________________________

Sample Code:

#3 : Get GPI 4 status

; Get GPI 4 Pin Status Register

In al, GPI_REG

;al bit0 = GPI 4 status

#4 : Set GPO 4 status to high

; Set GPO 0 Pin to High

mov dx, GPO_REG
in al, dx
or al, GPO_4

out dx, al

;al bit4 = GPO 4 status

Appendix – WDT & GPIO

GPI 4 GPI 5 GPI 6 GPI 7

IO Address 0xA06h 0xA06h 0xA06h 0xA06h

Bit 0 1 2 3

Sample code #3

GPO 4 GPO 5 GPO 6 GPO 7

IO Address 0xA06h 0xA07h #5 0xA04h

Bit 4 7 0 7

Sample code #4 #5

RCO-3200 | User’s Manual

99

#5 : GPO 6 must be accessed by gpio configuration (IO address is protected)

Set GPO 6 status to high

SIO_INDEX_Port equ 04Eh
SIO_DATA_Port equ 04Fh

SIO_UnLock_Value equ 087h

SIO_Lock_Value equ 0AAh
SIO_LDN_GPIO equ 06h

GPO_REG equ 0d1h

GPO_6 equ 00000001b

; Enable config mode

mov dx, SIO_INDEX_Port
mov al, SIO_UnLock_Value
out dx, al
jmp short $+2 ;Io_delay
jmp short $+2 ;Io_delay
out dx, al

; Switch GPIO Configuration for SIO LDN 0x06

mov dx, SIO_INDEX_Port
mov al, 07h
out dx, al
mov dx, SIO_DATA_Port
mov al, SIO_LDN_GPIO
out dx, al

; Set GPO 6 Pin to High

mov dx, SIO_INDEX_Port
mov al, GPO_REG
out dx, al
mov dx, SIO_DATA_Port
in al, dx
or al, GPO_6
out dx, al

;al bit0 = GPO 6 status

; Exit SIO

mov dx, SIO_INDEX_Port
mov al, SIO_Lock_Value
out dx, al

Appendix – WDT & GPIO

Copyright © Premio Inc. All Rights Reserved

www.premioinc.com