C&T Solution PS-H1701 HMI User Manual

PS-H1701

Intel Atom D2550 17” HMI System

User’s Manual

Version 1.0

C&T Solution Inc.
12F. -1, No.700, Zhongzheng Rd., Zhonghe Dist., New Taipei City 235, Taiwan

TEL: [phone]
http://www.candtsolution.com

PS-H1701 Intel Atom D2550 17” HMI System

２

Table of Contents

I. Preface ................................................................................................... ５

1.1 Disclaimer ................................................................................. ５

1.2 Copyright Notice ....................................................................... ５

1.3 Trademarks Acknowledgment .................................................. ５

1.4 Environmental Protection Announcement ................................ ６

1.5 Safety Precautions ................................................................... ６

II. Introduction ............................................................................................. ８

2.1 Product Description .................................................................. ８

2.2 Specifications ........................................................................... ９

III. Mechanical Specification .............................................................. １１

3.1 Dimensions ............................................................................ １１

3.2 Mechanical Layout................................................................. １３

3.2.1 Front View ...................................................................... １３

3.2.2 Side View ....................................................................... １３

3.2.3 Bottom View ................................ ................................ ... １４

3.2.4 Back View ...................................................................... １４

IV. Hardware Installation .................................................................... １５

4.1 Install Memory Module and SATA HDD ................................ １５

4.1.1 Install Memory Module ................................................... １５

4.1.2 Install SATA HDD ........................................................... １７

4.2 Mounting Bracket Installation ................................................ １８

4.2.1 Din Rail Installation ......................................................... １８

4.2.2 VESA Mount Installation ................................................. ２０

4.3 Panel Mount Installation ........................................................ ２２

V. Jumper Setting & Connectors .............................................................. ２５

5.1 Jumper Position ..................................................................... ２５

5.2 Jumper Setting ...................................................................... ２６

5.2.1 JBAT 1: CMOS Clear Jumper ........................................ ２６

5.2.2 JP1/3: LVDS1/2 VCC 5V/3.3V Select ............................. ２６

5.2.3 JP2/4: Inverter1/2 VCC 12V/5V Select ........................... ２６

5.2.4 JCOMP1/2/3/4: COM1/2/3/4 Pin9 Function Select ......... ２６

5.2.5 JP5: COM 4 RS232/422/485 Function Select ................ ２７

5.2.6 COPEN: Case Open Message Display Function Select . ２７

5.3 Connector Position ................................................................ ２８

5.3.1 External Connectors ....................................................... ２８

5.3.2 Internal Connectors ........................................................ ２９

PS-H1701 Intel Atom D2550 17” HMI System

３

5.4 External Connectors .............................................................. ２９

5.4.1 DC12V Power Connector ............................................... ２９

5.4.2 USB 2.0 Connectors ....................................................... ３０

5.4.3 DVI-I Connector .............................................................. ３０

5.4.4 RJ-45 LAN Connector .................................................... ３１

5.4.5 COM Connector: RS-232 ............................................... ３１

5.5 Internal Connectors ............................................................... ３２

5.5.1 SATA II Connectors ........................................................ ３２

5.5.2.............................................................................................. ３２

5.5.3 SATA Disc Power Connector: PWOUT1 ........................ ３２

5.5.4 Serial Port Headers: COM1/COM2/COM3/COM4 .......... ３２

5.5.5 RS422/485 Header: TX-RXCOM1 .................................. ３２

5.5.6 USB Port Headers: USB3/USB4 .................................... ３３

5.5.7 GPIO Header: GPIO ....................................................... ３３

5.5.8 Front Panel Header: JW_FP1 ........................................ ３３

5.5.9 Front Panel Audio Header: AUDIO1 ............................... ３３

5.5.10 CIR Header: CIR ............................................................ ３４

5.5.11 CPU FAN Header: CPUFAN1 ........................................ ３４

5.5.12 LVDS Inverter: INVERTER1 ........................................... ３４

5.5.13 LVDS Inverter: INVERTER2 ........................................... ３４

VI. SYSTEM BIOS ............................................................................. ３５

6.1 Main ....................................................................................... ３６

6.2 Advanced .............................................................................. ３７

6.2.1 ACPI Settings ................................................................. ３８

6.2.2 Wakeup Function Settings ............................................. ３９

6.2.3 CPU Configuration ......................................................... ４０

6.2.4 SATA Configuration ........................................................ ４１

6.2.5 USB Configuration .......................................................... ４２

6.2.6 Super IO Configuration ................................................... ４３

6.2.7 PC Health Status ............................................................ ４４

6.2.8 Serial Port Configuration ................................................ ４５

6.2.9 Clock Generator Configuration ....................................... ４６

6.2.10 Watchdog Configuration ................................ ................. ４６

6.2.11 Shutdown Temperature Configuration ............................ ４７

6.2.12 PPM Configuration ......................................................... ４８

6.3 Chipset .................................................................................. ４９

6.3.1 Host Bridge .................................................................... ５０

PS-H1701 Intel Atom D2550 17” HMI System

４

6.3.2 South Bridge................................................................... ５１

6.4 Boot ....................................................................................... ５２

6.5 Security ................................................................................. ５３

6.6 Save and Exit ........................................................................ ５４

VII. Address Map ................................................................................ ５５

7.1 I/O Port Address Map ............................................................ ５５

7.2 Interrupt Controller (IRQ) Map ............................................... ５７

7.3 Memory Map ......................................................................... ６０

PS-H1701 Intel Atom D2550 17” HMI System

５

I. Preface

1.1 Disclaimer

All specifications and information in this User’s Manual are believed to be
accurate and up to date. C&T Solution Inc. does not guarantee that the
contents herein are complete, true, accurate or non-misleading. The
information in this document is subject to change without notice and does not
represent a commitment on the part of C&T Solution Inc.

C&T Solution Inc. disclaims all warranties, express or implied, including,
without limitation, those of merchantability, fitness for a particular purpose with
respect to contents of this User’s Manual. Users must take full responsibility for
the application of the product.

1.2 Copyright Notice

All rights reserved. No part of this manual may be reproduced or transmitted in
any form or by any means, electronic or mechanical, including photocopying,
recording, or information storage and retrieval systems, without the prior
written permission of C&T Solutions Inc.

Copyright © 2012 C&T Solutions Inc.

1.3 Trademarks Acknowledgment

Intel®, Celeron® and Pentium® are trademarks of Intel Corporation.
Windows® is registered trademark of Microsoft Corporation.
AMI is trademark of American Megatrend Inc.
IBM, XT, AT, PS/2 and Personal System/2 are trademarks of International
Business Machines Corporation
All other products and trademarks mentioned in this manual are trademarks of
their respective owners.

PS-H1701 Intel Atom D2550 17” HMI System

６

1.4 Environmental Protection Announcement

Do not dispose this electronic device into the trash while discarding. Please
recycle to minimize pollution and ensure environment protection.

1.5 Safety Precautions

Before installing and using the equipment, please read the following
precautions:
 Put this equipment on a reliable surface during installation. Dropping it or

letting it fall could cause damage.

 The power outlet shall be installed near the equipment and shall be easily

accessible.

 Turn off the system power and disconnect the power cord from its source

before making any installation. Be sure both the system and the external
devices are turned OFF. Sudden surge of power could ruin sensitive
components. Make sure the equipment is properly grounded.

 When the power is connected, never open the equipment. The equipment

should be opened only by qualified service personnel.

 Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

 Disconnect this equipment from the power before cleaning. Use a damp

cloth. Do not use liquid or spray detergents for cleaning.

 Avoid the dusty, humidity and temperature extremes.

PS-H1701 Intel Atom D2550 17” HMI System

７

 Do not place heavy objects on the equipment.
 If the equipment is not used for long time, disconnect it from the power to

avoid being damaged by transient over-voltage.

 The storage temperature shall be above -20℃ and below 80℃.
 The computer is provided with a battery-powered real-time clock circuit.

There is a danger of explosion if incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer.

 If one of the following situation arises, get the equipment checked be

service personnel:

 The power cord or plug is damaged.
 Liquid has penetrated into the equipment.
 The equipment has been exposed to moisture.
 The equipment does not work well or it cannot work according the

user’s manual.

 The equipment has been dropped and damaged.
 The equipment has obvious signs of breakage.

PS-H1701 Intel Atom D2550 17” HMI System

８

II. Introduction

2.1 Product Description

The PS-H1701 HMI (Human Machine Interface) is powered by Intel Atom
D2550 1.86GHz dual core onboard processor with a 17” touch screen LCD.
The thickness of this panel system is only 5.4cm which is ideal for limited
space. In order to meet the criteria of the harsh industrial environment, the
system also provides optimal shock, vibration and temperature resistance.

The powerful CPU with integrated graphic engine provides a resolution up to
1280 x 1024 pixels. With Intel NM10 chipset, two Ethernet ports, five USB

2.0, two serial ports, and one DVI-I are provided as external I/O interface.
Besides the Cfast socket, the internal SATA interface provides an alternate
storage interface. Also, the extension Mini PCIe interface can be used by
many expansion cards, such as a wireless LAN card. With all these features,
the wide range of applications can be satisfied by the PS-H1701.

PS-H1701 Intel Atom D2550 17” HMI System

９

2.2 Specifications

 CPU

 Intel Atom D2550 1.86GHz

 Chipset

 Intel NM10

 System Memory

 One 204-pin DDR3 SODIMM socket
 800MHz or 1066MHz
 Up to 4GB

 BIOS

 AMI uEFI BIOS
 16MB SPI Flash ROM

 Watchdog Timer

 Hardware reset, 1sec-65535sec/min

 1 sec or 1 min step
 H/W Monitor
 LCD Display

 Graphic processing unit (GPU) integrated with CPU

 17” TFT LCD

 Resolution: SXGA (1280x1024)
 Brightness: 350 cd/m2

 Touch Screen

 USB type controller
 5-wire Resistive Type

 I/O

 Display

 One DVI-I connector

 CRT interface supports resolutions up to

1920x1200

 DVI interface supports resolution up to 1920x1200

 Ethernet

 Realtek RTL 8111E
 Two RJ-45 for Gigabit Ethernet

PS-H1701 Intel Atom D2550 17” HMI System

１０

 Audio

 Realtek ALC662 HD audio codec
 One Line-out

 Serial Port

 Two 9-pin D-sub male connector for RS-232

 USB Interface

 Five USB 2.0 connectors

 Power Input

 One 12V DC jack

 External 12V@5A, 60W AC/DC power adapter
 Expansion Interface

 One Mini PCIe
 Storage

 One 2.5” SATA HDD driver bay

 One CFast socket
 Power Management

 ACPI (Advanced Configuration and Power Interface) 3.0
 Temperature

 0℃~45℃
 Dimension

 406.5mm(W) x 333.5mm(H) x 54mm(D)

PS-H1701 Intel Atom D2550 17” HMI System

１１

III. Mechanical Specification

3.1 Dimensions

PS-H1701 Intel Atom D2550 17” HMI System

１２

detachable

reserved for antenna

detachable

PS-H1701 Intel Atom D2550 17” HMI System

１３

3.2 Mechanical Layout

3.2.1 Front View

Power LED: Indicates the power status of the system.
HDD LED: Indicates the status of the hard drive.

3.2.2 Side View

USB: Connects to USB2.0 devices.
DVD-ROM:. Reserved for DVD-ROM option.

PS-H1701 Intel Atom D2550 17” HMI System

１４

3.2.3 Bottom View

LAN: Connect to a local area network.
COM: Connect RS232 compatible serial devices.
DC +12V Input: Plug a DC power cord.
USB: Connects to USB2.0 devices.
DVI-I: Supports either VGA or LCD monitor.
Line-out: Connects to a headphone or speakers.
Brightness Down/ Brightness Up: Adjust the LCD brightness up and down

by pressing the buttons.

Power Switch: Press to power-on or power-off the system.

3.2.4 Back View

PS-H1701 Intel Atom D2550 17” HMI System

１５

IV. Hardware Installation

Make sure the system has been shut down and the power cord has been
unplugged.

4.1 Install Memory Module and SATA HDD

Step 1: Place the system front-side down and remove the 12 screws

“1”, 10 at the back and 2 at the bottom.

Step 2: Remove the rear cover.

4.1.1 Install Memory Module

.
Step 3: Remove the two screws “3” of the DVI-D connector at the
bottom I/O side.
Step 4: After remove the rear cover, locate the SBC close to the
bottom side.
Step 5: Remove the four screws “4” at the four corners of the SBC as
indicated in the diagram below.
Step 6: Remove the SBC from the panel.

PS-H1701 Intel Atom D2550 17” HMI System

１６

Step 7: Insert the plated side of the memory module into the socket.
Step 8: Push the module down until it is firmly locked by two latches.
Step 9: Put the SBC back and fasten all screws.
Step 10: Close the cover and fasten all screws.

PS-H1701 Intel Atom D2550 17” HMI System

１７

4.1.2 Install SATA HDD

Step 3: After remove the rear cover, use four screws to install a pair

of HDD brackets at two sides of a 2.5” SATA HDD as illustrated in the
diagram below.

Step 4: Use four screws to mount the HDD inside the panel.
Step 5: Connect the HDD connector.
Step 6: Close the rear cover and fasten all screws.

PS-H1701 Intel Atom D2550 17” HMI System

１８

4.2 Mounting Bracket Installation

C&T offers two optional accessories for mounting the system.

3-DINR-0002

Din Rail kit

3-VESA-0001

VESA mount kit

4.2.1 Din Rail Installation

Step 1: Use four screws to install the bracket “A” at the back as

indicated in the diagram below. Make sure the latches of the
bracket are facing down.

Step 2: Install the bracket B onto the bracket A by inserting the
latches into the holes, and then push the bracket B upward to wedge
it with the bracket A.
Step 3: Use six screws to mount the din-rail-base C to the bracket B
as shown below.

PS-H1701 Intel Atom D2550 17” HMI System

１９

Step 4: Insert the security screw at the bottom of the din-rail base as
indicated in the diagram below.

PS-H1701 Intel Atom D2550 17” HMI System

２０

Step 5: Make sure the din-rail kit are properly installed on the
system.
Step 6: Before secure the panel with the rail, make sure the rail is
solid and firm to hold the panel.

4.2.2 VESA Mount Installation

Step 1: Use four screws to install the bracket “A” at the back of the

panel as indicated in the diagram below. Make sure the latches of
the bracket are facing down.

Step 2: Install the bracket B onto the desired surface for display the
panel PC by using 6 screws as shown below. Make sure the bracket
is installed in the right direction.
Step 3: Attach the panel PC to the bracket B installed on the surface
by inserting the latches of the bracket A into the holes of the bracket
B.

PS-H1701 Intel Atom D2550 17” HMI System

２１

Step 4: After attaching the panel PC to the surface, make sure the
security screw is properly inserted as illustrated below.

PS-H1701 Intel Atom D2550 17” HMI System

２２

4.3 Panel Mount Installation

The Panel PC can be panel mounted. The cutout of the panel is a 387mm x
317mm square as shown below. Note the thickness of the panel and the Panel
Mount Seal together is 9.3mm maximum.

Step 1: Place the panel front-side down
Step 2: Remove the eight panel mount brackets around the panel PC

by pushing downward first.

PS-H1701 Intel Atom D2550 17” HMI System

２３

Step 3: Place the Panel Mount Seal down inside the edge of the
panel PC.

PS-H1701 Intel Atom D2550 17” HMI System

２４

Step 4: Place the panel on top of the Seal.
Step 5: Insert the eight brackets back into the panel PC as shown

below.

Step 5: Fasten eight screws on the brackets.

PS-H1701 Intel Atom D2550 17” HMI System

２５

V. Jumper Setting & Connectors

5.1 Jumper Position

Jumper

Name

JBAT1

CMOS RAM Clear Function Setting

JP1

LVDS1 5V/3.3V Select

JP2

Inverter1 VCC 12V/5V Select

JP3

LVDS2 5V/3.3V Select

JP4

Inverter2 VCC 12V/5V Select

JCOMP1

COM1 Header Pin9 Function Select

JCOMP2

COM2 Header Pin9 Function Select

JCOMP3

COM3 Header Pin9 Function Select

JCOMP4

COM4 Header Pin9 Function Select

JP5

COM4 RS232/422/485 Function Select

COPEN

Case Open Message Display Function

JP4

JP2

JP3

JBAT1

COPEN1

JP1

JP5

JCOMP4

JCOMP3

JCOMP2

JCOMP1

PS-H1701 Intel Atom D2550 17” HMI System

２６

5.2 Jumper Setting

5.2.1 JBAT 1: CMOS Clear Jumper

Function

Setting

Jumper

Normal (Default)

1-2 closed

Restore BIOS Defaults

2-3 closed

5.2.2 JP1/3: LVDS1/2 VCC 5V/3.3V Select

Function

Setting

Jumper

5V (Default)

1-2 closed

3.3V

2-3 closed

5.2.3 JP2/4: Inverter1/2 VCC 12V/5V Select

Function

Setting

Jumper

12V (Default)

1-2 closed

5V

2-3 closed

5.2.4 JCOMP1/2/3/4: COM1/2/3/4 Pin9 Function Select

Function

Setting

Jumper

RS232 (Default)

1-2 closed

+12V

3-4 closed

+5V

5-6 closed

PS-H1701 Intel Atom D2550 17” HMI System

２７

5.2.5 JP5: COM 4 RS232/422/485 Function Select

Function

Setting

Jumper

RS232 (Default)

1-2 closed

RS485

3-4 closed

RS422

5-6 closed

5.2.6 COPEN: Case Open Message Display Function Select

Function

Setting

Jumper

Normal (Default)

1-2 open

Case Open

1-2 short

PS-H1701 Intel Atom D2550 17” HMI System

２８

5.3 Connector Position

5.3.1 External Connectors

Connector

Name

J1

DC Power Connector

USB1/USB2

USB Port Connectors

DVI1

DVI-I Port Connector

LAN1/LAN2

RJ-45 LAN Connectors

FLINE_OUT1

Line Out Connector

Front Panel

Audio Header

SATA II Port

LVDS1 Header

DC 12V Power-in

Connector

DVI-I Port

RJ-45 LAN Port

RJ-45 LAN Port

USB 2.0 Ports

CIR Header

INVERTER2

USB 2.0 Ports

INVERTER1

LVDS2 Header

Mini PCIE slot

Power Switch Button

Reset Button

SODIMM Slot

CPUFAN1 Header

Front Panel Header

CFast Card Slot

TX-RX COM

GPIO Header

SATA DISK
Power Connector

Serial port Headers

(COM4/COM3/COM2/COM1)

USB 2.0

Header

Audio Line-out

SPDIF Out Header

PS-H1701 Intel Atom D2550 17” HMI System

２９

5.3.2 Internal Connectors

Header

Name

SATA1/SATA2

Serial ATA II Connector

PWOUT1

SATA Disk Power Connector

COM1/COM2/COM3/COM4

Serial Port Headers

TX-RXCOM1

RS422/485 Header

USB3/USB4

USB Headers

GPIO1

GPIO Header

AUDIO1

Front Panel Audio Header

JW_FP1

Front Panel Header
(PWR LED/ HDD LED/ Power Button/ Reset)

CIR

CIR Header

CPUFAN1

CPU FAN Header

INVERTER1/ INVERTER2

LVDS Inverter Connector

LVDS1

24-bit LVDS Header

LVDS2

18-bit LVDS Header

5.4 External Connectors

5.4.1 DC12V Power Connector

Connect to the 12V 5A 60W AC-DC power adapter.

Pin

Signal

1

+12V

2

GND

PS-H1701 Intel Atom D2550 17” HMI System

３０

5.4.2 USB 2.0 Connectors

Pin

Signal
USB Port 0

Pin

Signal
USB Port 1

1

USB +5 VCC

5

USB +5 VCC

2

USB#0_D-

6

USB#1_D-

3

USB#0_D+

7

USB#1_D+

4

GND

8

GND

5.4.3 DVI-I Connector

The DVI-I interface is the solution for either digital or analog signals. The DVI-I
connector could be used for an LCD or CRT monitor display.

Pin

Signal

Pin

Signal

Pin

Signal

1

TMDS Data2­Digital Red-(link1)

9

TMDS Data1­Digital Green-(link1)

17

TMDS Data0­Digital Blue-(link1)
& Digital Sync

2

TMDS Data2+
Digital Red+(link1)

10

TMDS Data1+
Digital Green+(link1)

18

TMDS Data0+
Digital Blue+ (link1)
& Digital Sync

3

Data2/4 Shield

11

Data1/3 Shield

19

Data0/5 Shield

4

TMDS Data4­Digital Green-(link2)

12

TMDS Data3­Digital Blue-(link2)

20

TMDS Data5­Digital Red-(link2)

5

TMDS Data4+
Digital Green+(link2)

13

TMDS Data3+
Digital Blue+(link2)

21

TMDS Data5+
Digital Red+(link2)

6

DDC Clock

14

+5V

22

TMDS clock shield

7

DDC Data

15

GND

23

TMDS Clock+

8

Analog Vertical Sync

16

Hot Plug Detect

24

TMDS Clock-

C1

Analog Red

C3

Analog Blue

C5

Analog GND
C2

Analog Green

C4

Analog Horizontal Sync

PS-H1701 Intel Atom D2550 17” HMI System

３１

5.4.4 RJ-45 LAN Connector

The RJ-45 connectors are for Ethernet.

Pin

Signal

Pin

Signal

1

MDI0+

5

MDI2+

2

MDI0-

6

MDI2-

3

MDI1+

7

MDI3+

4

MDI1-

8

MDI3-

A

Active LED
(Yellow)

B

10 LAN LED (OFF)
100 LAN LED (Green)
1000 LAN LED (Orange)

5.4.5 COM Connector: RS-232

Pin

Signal

Pin

Signal

1

DCD, Data Carrier Detect

6

DSR, Data Set Ready

2

RXD, Receive Data

7

RTS, Request To Send

3

TXD, Transmit Data

8

CTS, Clear To Send

4

DTR, Data Terminal Ready

9

RI, Ring Indicator
5

GND, Ground

PS-H1701 Intel Atom D2550 17” HMI System

３２

5.5 Internal Connectors

5.5.1 SATA II Connectors

Pin

Signal

1

GND

2

SATA_TX+

3

SATA_TX-

4

GND

5

SATA_RX-

6

SATA_RX+

7

GND

5.5.2

5.5.3 SATA Disc Power Connector: PWOUT1

Pin

Signal

1

5VSB

2

CIR_RX

3

GND

4

CIR LED

5.5.4 Serial Port Headers: COM1/COM2/COM3/COM4

Pin

Signal

Pin

Signal

1

DCD, Data Carrier Detect

2

RXD, Receive Data

3

TXD, Transmit Data

4

DTR, Data Terminal Ready

5

GND, Ground

6

DSR, Data Set Ready

7

RTS, Request To Send

8

CTS, Clear To Send

9

RI, Ring Indicator

5.5.5 RS422/485 Header: TX-RXCOM1

Pin

Signal

Pin

Signal

1

TXDP

3

RXDP

2

TXDN

4

RXDN

PS-H1701 Intel Atom D2550 17” HMI System

３３

5.5.6 USB Port Headers: USB3/USB4

Pin

Signal

Pin

Signal

1

VCC

2

VCC

3

DATA-

4

DATA-

5

DATA+

6

DATA+

7

GND

8

GND

9

KEY

10

NC

5.5.7 GPIO Header: GPIO

Pin

Signal

Pin

Signal

1

GPIO0

2

GPIO1

3

GPIO2

4

GPIO3

5

GPIO5

6

GPIO7

7

GPIO32

8

GPIO33

9

GND

10

+5V

5.5.8 Front Panel Header: JW_FP1

Pin

Signal

Pin

Signal

1

VCC5

HDD LED
2

VCC5

PWR LED
3

HDDLED

4

PWRLED

5

GND

RESET
Switch
6

PWRBTN

PWR Button
7

RSTSW

8 GND

5.5.9 Front Panel Audio Header: AUDIO1

Pin

Signal

Pin

Signal

1

MIC1-R

2

GND

3

MIC2-L

4

NC 5 LINEOUT-R

6

LINE1-R

7

SENSE

8

KEY

9

LINEOUT-L

10

LINE1-L

PS-H1701 Intel Atom D2550 17” HMI System

３４

5.5.10 CIR Header: CIR

Pin

Signal

1

5VSB

2

CIR Learn

3

GND

4

NC

5.5.11 CPU FAN Header: CPUFAN1

Pin

Signal

1

GND

2

+12V Fan Power

3

Fan Speed Dec

5.5.12 LVDS Inverter: INVERTER1

Pin

Signal

1

Backlight Enable

2

Backlight Duty

3

PVCC

4

PVCC

5

GND

6

GND

7

Backlight +SW

8

Backlight -SW

5.5.13 LVDS Inverter: INVERTER2

Pin

Signal

1

Backlight Enable

2

Backlight Duty/ NC

3

PVCC

4

PVCC

5

GND

6

GND

7

Backlight +SW/ NC

8

Backlight –SW/ NC

PS-H1701 Intel Atom D2550 17” HMI System

３５

VI. SYSTEM BIOS

The system BIOS software is stored on EEPROM. The BIOS provides an
interface to modify the configuration. When the battery is removed, all the
parameters will be reset.
Turn on the computer and press <DEL> or <F2> to enter the setup screen.

There are six menu bars on top of BIOS screen:

 Main To change system basic configuration
 Advanced To change system advanced configuration
 Chipset To change chipset configuration
 Boot To change boot settings
 Security Password settings
 Save & Exit Save setting, loading and exit options.

Press the ←/→ (left, right) arrow key on the keyboard to switch from menu bar.
The selected one is highlighted.

PS-H1701 Intel Atom D2550 17” HMI System

３６

6.1 Main

The Main setup screen is showed as following when the setup utility is entered.
System Date/Time is set up in the Main Menu.

System Date: MM/DD/YYYY
System Time: HH:MM:SS

Use Tab to switch between Date and Time elements.

PS-H1701 Intel Atom D2550 17” HMI System

３７

6.2 Advanced

Launch LAN1/LAN2 PXE OpROM: Enable or Disable Boot Option for Legacy

Network Devices

Launch Storage OpROM: Enable or Disable Boot Option for Legacy Mass
Storage Devices with Option ROM.

Onboard LAN 1 Controller: Enable or Disable PCI Express Root Port 1.

Onboard LAN 2 Controller: Enable or Disable Mini-PCIE Control.

ERP Support: Enable or Disable Energy-Related Products function. Disable

ERP for Active All Wakeup Function. (Include PS2, RTC, AC Power Loss,
etc..)

PS-H1701 Intel Atom D2550 17” HMI System

３８

6.2.1 ACPI Settings

ACPI Sleep State: Select the highest ACPI sleep state the system will

enter when the SUSPEND button is pressed.
Select between [Suspend Disabled] or [S3 (Suspend to RAM)].

PS-H1701 Intel Atom D2550 17” HMI System

３９

6.2.2 Wakeup Function Settings

Wake System with Fixed Time: Enable or disable System wake on

alarm event. When enabled, System will wake on the hr::min::sec
specified.

CIR Wake: Enable or Disable CIR Wakeup. This function is supported
only when ERP Function is disabled.

PS-H1701 Intel Atom D2550 17” HMI System

４０

6.2.3 CPU Configuration

Hyper-Threading: Enabled for Windows XP and Linux (OS optimized for

Hyper-Threading Technology) and Disabled for other OS (OS not
optimized for Hyper-Threading Technology).

Execute Disable Bit: XP can prevent certain classes of malicious buffer
overflow attacks when combined with a supporting OS (Windows Server
2003 SP1, Windows XP SP2, SuSE Linux 9.2, RedHat Enterprise 3
Update 3.)

Limit CPUID Maximum: Disabled/Enabled for Windows XP.

PS-H1701 Intel Atom D2550 17” HMI System

４１

6.2.4 SATA Configuration

SATA Controller(s): SATA Ports (0-3) Device Names if Present and

Enabled.
Configure SATA as: Select a configuration for SATA Controller, [IDE] or

[AHCI].

PS-H1701 Intel Atom D2550 17” HMI System

４２

6.2.5 USB Configuration

Legacy USB Support: Enables Legacy USB support. AUTO option

disabled legacy support if no USB devices are connected. DISABLE
option will keep USB devices available only for EFI applications.

EHCI Hand-off: This is a workaround for OSes without EHCI hand-off
support. The EHCI ownership change should be claimed by EHCI driver.

USB transfer time-out: The time-out value for Control, Bulk, and
Interrupt transfers. Select from [1 sec], [5 sec], [10 sec] and [20 sec].

Device reset time-out: USB mass storage device Start Unit command
time-out. Select from [10 sec], [20 sec], [30 sec] and [40 sec].

Device power-up delay: Maximum time the device will take before it
properly reports itself to the Host Controller. Select between [Auto] and
[Manual]. ‘Auto’ uses default value: for a Root port it is 100ms, for a Hub
port the delay is taken from Hub descriptor. When ‘manual’ is selected,
the value for the sub-item, Device Power-up delay in seconds, will have
to be set in the range of 1 to 40 seconds.

PS-H1701 Intel Atom D2550 17” HMI System

４３

6.2.6 Super IO Configuration

CIR Controller: Enable or Disable CIR Controller
Case Open Detect: Detect Case has already open or not. Show message

in POST.

PS-H1701 Intel Atom D2550 17” HMI System

４４

6.2.7 PC Health Status

SmartFAN Configuration:

CPUFAN1 SmartFan Mode: SmartFan Mode enabled or disabled.

When enabled, the following sub-items shall appear:

CPUFAN1 Full Speed Temp: Set a temperature for CPUFAN1

to run at full speed when above this specific temperature.

CPUFAN1 Idle Temp: Set a temperature for CPUFAN1 to idle

speed when below this specific temperature.

CPUFAN1 stop Temp: Set a temperature for CPUFAN1 to stop

when below this temperature.

PS-H1701 Intel Atom D2550 17” HMI System

４５

6.2.8 Serial Port Configuration

► COM 1 /2/3 Configuration

Serial Port: Enable or Disable Serial Port.
Change Settings: Select an optimal setting for Super IO device.

► Serial Port 4 Configuration

Serial Port: Enable or Disable serial port (COM).
Change Settings: Select an optimal setting for super IO device.
RS232 or RS 485 Select: Select RS 232 or RS 422/485 for serial port.

PS-H1701 Intel Atom D2550 17” HMI System

４６

6.2.9 Clock Generator Configuration

Clockgen Spread Spectrum: Enable or Disable Spread Spectrum

Function

IO Output Voltage: IO Output Voltage Setting. Select from [0.3V], [0.4V],
[0.5V], [0.6V], [0.7V], [0.8V], [0.9V] and [1.0V]

6.2.10 Watchdog Configuration

WatchDog Timer Control: Used to enable or disable WatchDog Timer.

When enabled is selected, the following sub-item shall appear:
WatchDog Timer Value: Set a value in the range of 4 to 255.
WatchDog Timer Unit: Select between [Second] and [Minute].

PS-H1701 Intel Atom D2550 17” HMI System

４７

6.2.11 Shutdown Temperature Configuration

Select the system shutdown temperature. Select from [Disabled], [60C/140F],
[65C/149F], [70C/158F], [75C/167F]].

PS-H1701 Intel Atom D2550 17” HMI System

４８

6.2.12 PPM Configuration

EIST: Enable or Disable Intel SpeedStep.

CPU C state Report: Enable or Disable CPU C state report to OS.

Enhanced C state: Enable or Disable Enhanced CPU C state.
CPU Hard C4E: Enable or Disable CPU Hard C4E function.
CPU C6 state: Enable or disable CPU C6 state.

PS-H1701 Intel Atom D2550 17” HMI System

４９

6.3 Chipset

PS-H1701 Intel Atom D2550 17” HMI System

５０

6.3.1 Host Bridge

Internal Graphics: Keep IGD enabled based on the setup options.
IGFX-Boot Type: Select the Video Device which will be activated during

POST. This has no effect if external graphics present.
Select from: [VBIOS Default], [DVI -> CRT], [DVI/HDMI], [LVDS2];
[LVDS1], [HDMI+LVDS1], [CRT+LVDS2], [CRT+LVDS1]

Panel Scaling: Select the LCD panel scaling option used by the Internal
Graphics Device.
Select from: [Auto]; [Force Scaling]; [Off]; [Maintain Aspect Ratio]

Backlight Control: Back Light Control Setting.
Select [PWM Inverted] or [PWM Normal].

Active LFP: Select the Active LFP Configuration.

PS-H1701 Intel Atom D2550 17” HMI System

５１

6.3.2 South Bridge

Azalia Controller: Enable/ Disable Azalia Controller.
UHCI #1/#2/#3/#4: Control the USB UHCI (USB1.1) functions. Disable

from highest to lowest controller.

USB 2.0 (EHCI) Support: Enable or Disable USB2.0 (EHCI) Support.
High Precision Timer: Enable or Disable the High Precision Event Timer.
SLP_S4 Assertion Width: Select a minimum assertion width of the

SLP_S4# signal. Select from: [1-2 Seconds]; [2-3 Seconds]; [3-4
Seconds]; [4-5 Seconds].

Restore AC Power Loss: Select AC power state when power is
re-applied after a power failure. Select from: [Power Off]; [Power On];
[Last State].

PS-H1701 Intel Atom D2550 17” HMI System

５２

6.4 Boot

Setup Prompt Timeout: Set number of seconds to wait for setup

activation key. 65535 (0xFFFF) means indefinite waiting.
Bootup NumLock State: Select the keyboard NumLock state, [On] or

[Off].

Quiet Boot: Enables or disables Quiet Boot option.
GateA20 Active: Select between [Upon Request] and [ Always].

[Upon Request]: GA20 can be disabled using BIOS services.

[Always]: Do not allow disabling GA20; this option is useful when any
RT code is executed above 1MB.

Option ROM Messages: Set display mode for Option ROM. Select
between [Force BIOS] and [Keep Current].

Interrupt 19 Capture: When enabled, Option ROMs is allowed to trap Int

19.

PS-H1701 Intel Atom D2550 17” HMI System

５３

6.5 Security

Administrator’s and User’s passwords could be set.
If ONLY the Administrator’s password is set, then this only limits access to
Setup and is only asked for when entering Setup. If ONLY the User’s password
is set, then this is a power on password and must be entered to boot or enter
Setup. In Setup, the user will have administrator rights. The minimum length of
the password is 3 and the maximum length is 20.

PS-H1701 Intel Atom D2550 17” HMI System

５４

6.6 Save and Exit

Save Changes and Reset: Reset the system after saving the changes.
Discard Changes and Reset: Reset system setup without saving any

changes.

Restore Defaults: Restore/Load Default values for all the setup options.
Save as User Defaults: Save the changes done so far as user Defaults.
Restore user Defaults: Restore the User Defaults to all the setup options.

PS-H1701 Intel Atom D2550 17” HMI System

５５

VII. Address Map

7.1 I/O Port Address Map

The assignment of the I/O port addresses of the PS-H1701 under Windows® 7
Ultimate/32bit is shown below.

PS-H1701 Intel Atom D2550 17” HMI System

５６

PS-H1701 Intel Atom D2550 17” HMI System

５７

7.2 Interrupt Controller (IRQ) Map

The interrupt controller map of PS-H1701 under Windows® 7 Ultimate/32bit is
as shown below.

PS-H1701 Intel Atom D2550 17” HMI System

５８

PS-H1701 Intel Atom D2550 17” HMI System

５９

PS-H1701 Intel Atom D2550 17” HMI System

６０

7.3 Memory Map

The memory map of DRAM of PS-H1701 under Windows® 7 Ultimate/32bit is
shown below.