C&T Solution CT-DBX0x User Manual

Download

Page 1

CT-DBX0x

3.5” Industrial Single Board

Computer with Intel® Atom™ Processor E3800

Page 2

CT-DBT0X l User’s Manual

Table of Contents

Prefaces …………………………………………………….……………………………………………. 04

Revision …………………………………………………………………………………………..……………….……….. 04 Disclaimer ………………………………………………………..…….…….………………………….……………….. 04 Copyright Notice …………………………………….…………………….…………………………………………… 04

Trademarks Acknowledgment …………..……………………………………………………….................. 04

Environmental Protection Announcement …………………………….………………….…………..….. 04

Safety Precautions ………………………………………….……………………………….…………….……….... 05

Technical Support and Assistance …………………………………….…………….…………….………….. 06 Conventions Used in this Manual ………………………………………………………………….….………. 06

Chapter 1 Product Introductions ………………………………………………………..… 07

1.1 Product Description ……….………………………………..………….………………..………. 08

1.2 Specifications ………………..………………………….....…………….…………..…..………… 09

1.3 Available Models …………………..……………………..…………………………………..…... 10

1.4 Block Diagram ………………………………..…………………………..………..……….………. 11

Chapter 2 Mechanical Specifications ….…………………..………………………..…. 12

2.1 Dimensions ……………………………….…………………………………..…….…..……..….... 13

2.2 Board Layout ……………………………………………………….……….…….………............ 14

2.2.1 Connectors & Jumpers ………………………………………………....……………… 14

2.3 Jumpers Definition ………….………..…............................................................. 15

2.3.1 Serial Port COM1 …………….…………………………………………....……………… 15

2.3.2 VGA Connector ………..…….…………………………………………....……………… 16

2.3.3 USB 3.0 Connector ……..……….……………………………………....……………… 17

2.3.4 USB 2.0 Connector ……..……….……………………………………....……………… 17

2.3.5 HDMI Connector ……..…..……………………………………………....……………… 17

2.3.6 LAN Connector ………..…………..……………………………………....……………… 17

2.4 Internal Connectors ………….……………........................................................... 18

2.4.1 Front Panel Audio Connector (AUDIO) ………….……………....……………… 18

2.4.2 Backlight Control Connector (CN1) …………………………………………..…… 18

2.4.3 COM2-4 Serial Ports (COM2-4) ………………………..……………………..….… 18

2.4.4 LPC Connector (DBG) ……………………………………………………………………. 19

2.4.5 Fan Connector (FAN) …………………………………………………………………….. 19

2.4.6 GPIO Connector: GPIO …….…………………………………………....……………… 19

2.4.7 Power Button Pin Header (JP3) ………….………………………....……………… 19

2.4.8 Reset Button Pin Header (JP4) ……………………………………....……………… 20

2.4.9 Reset Button Pin Header (JP6) ……………………………………....……………… 20

2.4.10 I2C Pin Header (I2C1) ………………………………………………....……………… 20

2.4.11 Multi-LED Pin Header (LED) ………………………………………...……………… 20

2.4.12 LVDS Connector: LVDS ……………………………………………….……………….. 21

2.4.13 microSD Coonector (MICRO_SD) ………………………………………………… 21

2.4.14 Mini-PCIe Slot #1 (PCIE1_MSATA) ……………………………...……….……… 22

2.4.15 Mini-PCIe Slot #2 (MINI_PCIE1) …………………………….…………….…….. 23

2.4.16 ATX Power Connector (POWER_CONN) …………………...………………… 23

2.4.17 PS/2 Keyboard/Mouse Connector (PS2) …………………….……………….. 23

2.4.18 SATA Signal Connectors: SATA1_2 …………………………………………..…… 24

2.4.19 SATA Power Connectors (SATA1/2_PWR) …………………...………….…… 24

2.4.20 USB 2.0 Pin Header (USB_1/2) ……….………………………….……………….. 24

Page 3

CT-DBT0X l User’s Manual

2.5 Jumper Settings ………..…….……………............................................................ 25

2.5.1 Backlight Power (JP1) ………….………………………………………..……………… 25

2.5.2 Panel Power (JP2) ……………….………………………………………..……………… 25

2.5.3 Clear CMOS (JP8) ………….…….………………………………………..……………… 25

Chapter 3 Features & Interfaces ………………………………………………………..… 26

3.1 Processor ……………………….………………………………..………….………………..………. 27

3.2 BIOS ……………………………..………………………….....…………….…………..…..………… 27

3.3 System Memory ……….…………..……………………..…………………………………..…... 27

3.4 Graphics ………………………………………..…………………………..………..……….………. 27

3.5 USB ……………………………….………………………………..………….………………..………. 27

3.6 Ethernet ……..………………..………………………….....…………….…………..…..………… 27

3.7 SATA ………………..……….…………..……………………..…………………………………..…... 27

3.8 Audio ………………………………..…………..…………………………..………..……….………. 27

3.9 Expansion ……………………..………………………….....…………….…………..…..………… 28

3.10 General Purpose Input Output ……………………..…………………………………..…... 28

3.10.1 GPIO Configuration ……………………..……….………………………………..…... 28

3.11 Watchdog Timer ………………..…………..…………………………..………..……….………. 29

3.11.1 Board Design ……………..………………..……….………………..……………..…... 29

3.11.2 Psuedo Code ……………..………………..……….……………………..………..…... 29

Chapter 4 Driver Installation ….…………………..………………..……………..…..…. 30 Chapter 5 System BIOS ….…………………………..………………..……………..…..…. 32

5.1 Advanced ……………………………….…………………………………..……….…..……..….... 33

5.1.1 ACPI Settings …………….…………………………………………....…………………… 34

5.1.2 F81866 Super IO Configuration ………..…….………………..…………..……… 34

5.1.3 Hardware Monitor ……..……….……………………………………....……………… 36

5.1.4 Serial Port Console Redirection ……..……….……………....………………..… 36

5.1.5 CPU Configuration ……..……………………………………………....…………..…… 37

5.1.6 SATA Configuration …………..……………………………………....……………….… 38

5.1.7 Miscellaneous Configuration …………….………………………....……………… 38

5.1.8 LPSS & SCC Configuration ………..…….………………..………………………….. 39

5.1.9 Network Stack Configuration ……..……….…………………....………………… 39

5.1.10 CSM Configuration ……..……….………………………….………....……………… 40

5.1.11 SDIO Configuration ……..………………………..…………………....……………… 41

5.1.12 USB Configuration …………..…………………..……………….…....……………… 42

5.1.13 Security Configuration …………..……..…………………………....……………… 43

5.2 Chipset ………….………………………………........................................................... 44

5.2.1 Northbridge Configuration …………..……………………………....……………… 44

5.2.2 Southbridge Configuration …………..……………………………....……………… 47

5.3 Security …….……………………..……………........................................................... 48

5.3.1 Security Boot Menu …………..………..……………………………....……………… 49

5.4 Boot ……………..………………………………........................................................... 50

5.5 Save and Exit …………………………………........................................................... 50

Chapter 6 Address Map ….…………………………..………………..……………..…..…. 51

6.1 I/O Port Address Map ……………………………..…………………..……….…..……..….... 52

6.2 Interrupt Controller (IRQ) Map ……..……………………..……..……….…..……..….... 55

6.3 Memory Map ……………………….………………..…………………..……….…..……..….... 63

Page 4

CT-DBT0X l User’s Manual

Revision

Disclaimer

All specifications and information in this User’s Manual are believed to be accurate and up to date. C&T

Solution Inc. does not guarantee that the contents herein are complete, true, accurate or non-misleading. The information in this document is subject to change without notice and does not represent a commitment on the part of C&T Solution Inc. C&T Solution Inc. disclaims all warranties, express or implied, including, without limitation, those of

merchantability, fitness for a particular purpose with respect to contents of this User’s Manual. Users must

take full responsibility for the application of the product.

All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording, or information storage and retrieval systems, without the prior written permission of C&T Solutions Inc. Copyright © 2015 C&T Solutions Inc.

Trademarks Acknowledgment

Intel®, Celeron® and Pentium® are trademarks of Intel Corporation. Windows® is registered trademark of Microsoft Corporation. AMI is trademark of American Megatrend Inc. IBM, XT, AT, PS/2 and Personal System/2 are trademarks of International Business Machines Corporation All other products and trademarks mentioned in this manual are trademarks of their respective owners.

Environmental Protection Announcement

Do not dispose this electronic device into the trash while discarding. Please recycle to minimize pollution and ensure environment protection.

Prefaces

Revision

Description

Date

100

Initial release

2015/04/13

110

Correct USB_1/2 connector drawing; POWER_CONN & COM2

-4 connector descriptions

2015/05/06

120

Modify COM_2/3/4 connector table and drawing

2015/12/08

Preface

Page 5

CT-DBT0X l User’s Manual

Safety Precautions

Before installing and using the equipment, please read the following precautions:

 Put this equipment on a reliable surface during installation. Dropping it or letting it fall could

cause damage.

 The power outlet shall be installed near the equipment and shall be easily accessible.

 Turn off the system power and disconnect the power cord from its source before making any

installation. Be sure both the system and the external devices are turned OFF. Sudden surge

 of power could ruin sensitive components. Make sure the equipment is properly grounded.

 When the power is connected, never open the equipment. The equipment should be opened

only by qualified service personnel.

 Make sure the voltage of the power source is correct before connecting the equipment to the

power outlet.

 Disconnect this equipment from the power before cleaning. Use a damp cloth. Do not use

liquid or spray detergents for cleaning.

 Avoid the dusty, humidity and temperature extremes.

 Do not place heavy objects on the equipment.

 If the equipment is not used for long time, disconnect it from the power to avoid being

damaged by transient over-voltage.

 The storage temperature shall be above -40°C and below 85°C.

 The computer is provided with a battery-powered real-time clock circuit. There is a danger of

explosion if incorrectly replaced. Replace only with the same or equivalent type

recommended by the manufacturer.

 If one of the following situation arises, get the equipment checked be service personnel:

• The power cord or plug is damaged.

• Liquid has penetrated into the equipment.

• The equipment has been exposed to moisture.

• The equipment does not work well or it cannot work according the user’s manual.

• The equipment has been dropped and damaged.

• The equipment has obvious signs of breakage.

Preface

Page 6

CT-DBT0X l User’s Manual

Technical Support and Assistance

1. Visit the C&T Solution Inc website at www.candtsolution.com where you can find the latest

information about the product.

2. Contact your distributor, our technical support team or sales representative for technical support if

you need additional assistance. Please have following information ready before you call:

 Model name and serial number

 Description of your peripheral attachments

 Description of your software (operating system, version, application software, etc.)

 A complete description of the problem

 The exact wording of any error messages

Conventions Used in this Manual

Preface

This indication alerts operators to an operation that, if not strictly observed, may result in severe injury.

WARNING

This indication alerts operators to an operation that, if not strictly observed, may result in safety hazards to personnel or damage to equipment.

CAUTION

This indication provides additional information to complete a task easily.

NOTE

Page 7

Chapter 1

Product Introductions

Page 8

CT-DBT0X l User’s Manual

1.1 Product Description

The CT-DBT0x is a single board computer in 3.5” SBC form factor featuring the Intel® Atom™ Processor

E3800 Series in FCBGA1170 package on 22nm process technology in a single chip solution. One 240-

pin SODIMM sockets supports non-ECC/unbuffered DDR3L 1333MHz memory up to 4GB. The Intel®

HD graphics controller integrated within the processor supports three independent displays (VGA,

HDMI, LVDS). The CT-DBT0x supports 2x Gigabit Ethernet, USB 3.0/2.0, COM, GPIO, 2x Mini-PCIe slots,

microSD card SIM card to support a variety of industrial applications.

Chapter 1: Product Introductions

Page 9

CT-DBT0X l User’s Manual

Chapter 1: Product Introductions

1.2 Specifications

CPU

• Intel® Atom™ Processor E3800 Series and Intel®

Celeron® Processor J1900 SoC in FCBGA1170 package

- Atom™ E3845: 4-core, 1.91GHz, TDP 10W

- Atom™ E3827: 2-core, 1.75GHz. TDP 8W

- Atom™ E3815: 1-core, 1.46GHz, TDP 5W

- Celeron® J1900: 4-core, 2.00GHz, TDP 10W

- Celeron® N2807: 4-cores, 1.58GHz, TDP 4.3W

System Memory

• One 204-pin DDR3L SODIMM socket

• 1333MHz, non-ECC unbuffered

• Data transfer rates up to 1333MT/s

• Up to 4GB

BIOS

• AMI uEFI BIOS

• 8MB SPI flash ROM

Graphics

• Intel® HD Graphics Gen 7 integrated in CPU

• 1x VGA, resolution up to 2560x1600@60Hz

• 1x HDMI 1.4a interface, up to 1920x1080@60Hz

Ethernet

• Two Intel® I210IT GbE Controllers

• 10/100/1000BASE-TX Ethernet

• WOL/PXE support

Audio

• Realtek ALC88

• Line-In, Line-Out and Mic-In

Internal I/O

• 2x 7-pin SATA 3Gb/s ports (w/ 2x +12V/+5V/GND

power)

• 4x USB 2.0 ports via header (1 from SoC, 3 from

USB 2.0 Hub IC, Genesys GL852GT-OHY12)

• 1x RS-232/422/485 port (BIOS selectable, supports

auto-flow)

• 3x RS-232 ports via header (COM2-4)

• 1x 8-bit GPIO (4-bit input, 4-bit output, +5V level,

GPO default “High”, GPI supports SMI trigger)

• 1x PS/2 keyboard and mouse

• 1x front panel audio

• 1x Reset button header

• 1x Power on/off header

• 1x wafer connector for external CMOS battery

(included)

• 1x header for I2C Serial IO interface from SoC

• 1x Clear CMOS header

• 1x 4-pin fan connector

• 1x 4-pin ATX power connector for +12VDC power

input

External I/O

• +12V DC power input

• 1x HDMI port (vertical)

• 1x VGA (DB-15)

• 2x GbE (RJ-45)

• 1x USB 3.0

• 1x USB 2.0

• 1x RS-232/422/485 COM1 (DB-9,

RS-485 auto low control supported)

Expansion

• 2x Mini PCIe slots, full size

- Mini PCIe slot #1: PCIe x1 only or mSATA only (by BOM option, see 1.3 Available Models)

- Mini PCIe slot #2: PCIe x1 & USB 2.0 (USB 2.0 port from USB Hub IC)

• 1x microSD card slot

• 1x SIM card slot

Watchdog Timer

• H/W Reset, 1-255 sec./min.

• 1 sec. or 1min. Increments

Hardware Monitor

• System voltages

- CPU core power

- CPU I/O power

- DDR power

- VCC3

- Vin

• Temperatures monitoring

• Smart Fan support

Power

• DC +12V input

• ACPI 5.0 compliant

Form Factor

• 3.5” SBC, 146mm x 102mm

Operating Temp.

• -20°C to 70°C

Storage Temp.

• -40°C to 85°C

Operating Humidity

• 10% to 90% relative humidity, non-condensing

Certifications

• CE

• FCC Class A

Page 10

CT-DBT0X l User’s Manual

1.3 Available Models

Chapter 1: Product Introductions

Model No. Processor Ordering Information Part Number

CT-DBT01

Atom™ E3845

-DBT01-E3845

-DBT0101S100-P0

Atom™ E3827

-DBT01-E3827

-DBT0102S100-P0

Atom™ E3815

-DBT01-E3815

-DBT0103S100-P0

Celeron® J1900

-DBT01-J1900

-DBT0104S100-P0

Celeron® N2807

-DBT01-N2807

-DBT0105S100-P0

CT-DBT02

Atom™ E3845

-DBT02-E3845

-DBT0201S100-P0

Atom™ E3827

-DBT02-E3827

-DBT0202S100-P0

Atom™ E3815

-DBT02-E3815

-DBT0203S100-P0

Celeron® J1900

-DBT02-J1900

-DBT0204S100-P0

Celeron® N2807

-DBT02-N2807

-DBT0205S100-P0

Mini PCIe slot #1 Mini PCIe slot #2

-DBT01

PCIe

x1 only

PCIe x1 & USB 2.0

-DBT02

mSATA only

PCIe

x1 & USB 2.0

Mini PCIe Slot BOM Options

Page 11

CT-DBT0X l User’s Manual

1.4 Block Diagram

Chapter 1: Product Introductions

Page 12

Chapter 2

Mechanical Specifications

Page 13

CT-DBT0X l User’s Manual

2.1 Dimensions

Chapter 2: Jumper & Connectors

Units: mm

Page 14

CT-DBT0X l User’s Manual

2.2 Board Layout

2.2.1 Connectors & Jumpers

Chapter 2: Jumper & Connectors

Connector Description Connector Description

AUDIO

Front Audio connector

I2C1

I2C header

CN1

Backlight Control connector

LED

LED header

COM1

-232/422/485 DB9 connector

LVDS

LVDS connector

COM2

-4

-232 COM2-4 headers

MICRO_SD

microSD card slot

DBG

LPC connector

MINI_PCIE2

Mini PCI Express slot 2

DIMM

240

-pin SODIMM socket

PCIE1_MSATA

Mini PCI Express slot 1

FAN

Fan connector

POWER_CONN

ATX Power connector

GPIO

GPIO header

PS2

PS/2

KB/MS wafer connector

HDMI

HDMI port

RJ45

LAN ports

JP1

Backlight Power Select jumper

SATA1/2

SATA Port 1/2 signal connector

JP2

Panel Power Select jumper

SATA1/2_PWR

SATA Port 1/2 power connector

JP3

Power Button header

SIM1

SIM card slot

JP4

Reset Button header

USB_1/2

USB 2.0 headers

JP6

Battery connector

USB_3

USB 2/0/3.0 ports

JP8

Clear CMOS

VGA

VGA connector

Page 15

CT-DBT0X l User’s Manual

2.3 External Connectors

2.3.1 Serial Port COM1

2.3.1.1 RS-2332 Mode

2.3.1.2 RS-422 Mode

2.3.1.3 RS-485 Mode

Chapter 2: Jumper & Connectors

Pin Signal Pin Signal

1 DCD, Data Carrier Detect 6 DSR, Data Set Ready

2 RXD, Receive Data 7 RTS, Ready To Send

3 TXD, Transmit Data 8 CTS, Clear To Send

4 DTR, Data Terminal Ready

9 RI, Ring Indicator

5 GND, Ground

COM1 VGA USB 2.0 HDMI LAN

Pin Signal Pin Signal

1 TXD-, Transmit Data 6 NA

2 RXD+, Receive Data 7 NA

3 TXD+, Transmit Data 8 NA

4 RXD-, Receive Data

9 NA

5 NA

Pin Signal Pin Signal

1 Data- 6 NA

2 Data+ 7 NA

3 NA 8 NA

4 NA

9 NA

5 NA

Page 16

CT-DBT0X l User’s Manual

2.3.1.4 COM1 RS-232/422/485 Mode Selection

To set the COM mode, boot the system into BIOS Setup Utility and select Advanced > F81866 Super IO configuration. You will see the following screen.

Select the COM port you wish to setup and choose from RS-232, RS-422 and RS-485.

If RS-485 is selected, you can enable/disable the RS-485 Auto Flow Function which automatically handles half-duplex control.

Save the configuration and exit the BIOS Setup Utility ("F4" hotkey).

2.3.2 VGA Connector

15-pin D-sub Female Connector

Chapter 2: Jumper & Connectors

Pin Signal Pin Signal

1 VGA_RED 9 VCC

2 VGA_GRN 10 GND

3 VGA_BLU 11 NC

4 NC 12 VGA_DDC_DAT

5 GND 13 VGA_HSYNC

6 GND 14 VGA_VSYNC

7 GND

15 VGA_DCC_CLK

8 GND

Page 17

CT-DBT0X l User’s Manual

2.3.3 USB 3.0 Connector

2.3.4 USB 2.0 Connector

2.3.5 HDMI Connector

2.3.6 LAN Connector

Chapter 2: Jumper & Connectors

Pin Signal Pin Signal

1 USB +5V 5 USB_SSRX-

2 USB_D- 6 USB_SSRX+

3 USB_D+ 7 GND_DRAIN

4 GND

8 USB_SSTX-

9 USB_SSTX+

Pin Signal

1 USB +5V 2 USB_D3 USB_D+ 4 GND

1 2 3 4

Pin Signal Pin Signal

1 HDMI_TX2_DP_B 2 GND

3 HDMI_TX2_DN_B 4 HDMI_TX1_DP_B

5 GND 6 HDMI_TX1_DN_B

7 HDMI_TX0_DP_B 8 GND

9 HDMI_TX0_DN_B 10 HDMI_CLK_DP_B

11 GND 12 HDMI_CLK_DN_B

13 NC 14 NC

15 HDMI_SCLDDC_B 16 HDMI_SDADDC_B

17 GND 18 +5V

19 1 18 2

Pin Signal Pin Signal

1 MDI0+ 5 MDI2-

2 MDI0- 6 MDI1-

3 MDI1+ 7 MDI3+

4 MDI2+ 8 MDI3-

A Active LED (Yellow) B

10 LAN LED (OFF)

100 LAN LED (Green)

1000 LAN LED (Orange)

Page 18

CT-DBT0X l User’s Manual

2.4 Internal Connectors

2.4.1 Front Panel Audio Connector (AUDIO)

Connector Type: 2x6-pin pitch 2.00mm wafer connector

2.4.2 Backlight Control Connector (CN1)

Connector Type: 2x6-pin pitch 2.00mm wafer connector

2.4.3 COM2-4 Serial Ports (COM2-4)

Connector Type: 1x9-pin pitch 1.5mm wafer connector

Chapter 2: Jumper & Connectors

Pin Signal Pin Signal

1 MICIN_L 2 MICIN_R

3 MIC1_JD 4 AGND

5 LOUT_L 6 LOUT_R

7 FRONT_JD 8 AGND

9 LIN_L 10 LIN_R

11 LINE1_JD 12 AGND

Pin Signal Pin Signal

1 Backlight Enable 5 GND

2 Backlight CTRL 6 GND

3 Backlight PWR 7 NC

4 Backlight PWR 8 NC

1 8

Pin Signal

DCD, Data Carrier Detect

DSR, Data Set Ready

RXD, Receive Data

RTS, Request To Send

TXD, Transmit Data

CTS, Clear To Send

DTR, Data Terminal Ready

RI, Ring Indicator

GND

1 9

Page 19

CT-DBT0X l User’s Manual

2.4.4 LPC Connector (DBG)

Connector Type: 2x5 pin pitch 1.27mm box header

2.4.5 Fan Connector (FAN)

Connector Type: 1x4 pin pitch 2.54mm wafer connector

2.4.6 GPIO Connector: GPIO

Connector Type: 2x5-pin pitch 2.0mm wafer connector

2.4.7 Power Button Pin Header (JP3)

Connector Type: 1x2-pin pitch 2.00mm wafer connector

Chapter 2: Jumper & Connectors

Pin Signal Pin Signal

1 GND 2 +3.3V

3 LPC_AD3 4 NC

5 LPC_AD2 6 RESET_DBG

7 LPC_AD1 8 CLOCK_DEBUG

9 LPC_AD0 10 LPC_FRAME

Pin Signal

1 GND

2 +12V Fan Power

3 Fan Sensor

4 Fan PWM

Pin Signal Pin Signal

1 +5V 2 GND

3 GPO0 4 GPI0

5 GPO1 6 GPI1

7 GPO2 8 GPI2

9 GPO3 10 GPI3

Pin Signal

1 PS_ON_BUTTON_N

2 GND

Page 20

CT-DBT0X l User’s Manual

2.4.8 Reset Button Pin Header (JP4)

Connector Type: 1x2-pin pitch 2.00mm wafer connector

2.4.9 Battery Pin Header (JP6)

Connector Type: 1x2-pin pitch 1.25mm wafer connector

2.4.10 I2C Pin Header (I2C1)

Connector Type: 1x3-pin pitch 2.54mm pin header connector

2.4.11 Multi-LED Pin Header (LED)

Connector Type: 2x6-pin pitch 2.00mm wafer connector

Chapter 2: Jumper & Connectors

Pin Signal Pin Signal

+5V2+5V

Power ON/OFF

HDD LINK/ACTIVE

+3.3V

LAN1 Speed 1000

LAN1 LINK/ACTIVE

LAN1 Speed 100

+3.3V

LAN2 Speed 1000

LAN2 LINK/ACTIVE

LAN2 Speed 100

Pin Signal

1 RESET_BUTTON_N

2 GND

Pin Signal

1 GND

2 +3V

Pin Signal

1 CLOCK

2 GND

3 DATA

Page 21

CT-DBT0X l User’s Manual

2.4.12 LVDS Connector: LVDS

Connector Type: 2x15-pin pitch1.25mm LVDS connector

2.4.13 microSD Connector (MICRO_SD)

Chapter 2: Jumper & Connectors

Pin Signal Pin Signal

LVDS_B3

- 2

LVDS_B3+

LVDS_B_CLK

- 4

LVDS_B_CLK+

LVDS_B2

- 6

LVDS_B2+

LVDS_B1

- 8

LVDS_B1

LVDS_B0

- 10

LVDS_B0+

LVDS_I2C_DAT

LVDS_I2C_CK

GND

LVDS_A3+

LVDS_A3

LVDS_A_CLK+

LVDS_A_CLK

LVDS_A2+

LVDS_A2

LVDS_A1+

LVDS_A1

LVDS_A0+

LVDS_A0

Panel PWR

Pin Signal Pin Signal

1 DAT2 2 CD/DAT3 3 CMD 4 VDD 5 CLK 6 VSS

7 DAT0 8 DAT1

Page 22

CT-DBT0X l User’s Manual

2.4.14 Mini-PCIe Slot #1 (PCIE1_MSATA)

PCIe x1 only (CT-DBT01 BOM option)

mSATA only (CT-DBT02 BOM option)

Chapter 2: Jumper & Connectors

Pin Definition Pin Definition Pin Definition

WAKE#

Reserved

+3.3V

Reserved

USB_D+

Reserved

GND39Reserved

GND22PERST#

GND5Reserved

PERn0

Reserved

+1.5V

3.3Vaux 42

LED_WWAN#

CLKREQ#

PERp0

Reserved

UIM_PWR

GND44LED_WLAN#

GND27GND45Reserved

UIM_DATA

+1.5V

LED_WPAN#

REFCLK

- 29

GND47Reserved

UIM_CLK

SMB_CLK

+1.5V

REFCLK+

PETn0

Reserved

UIM_RESET

SMB_DATA

GND

GND33PETp0

Reserved

UIM_VPP

GND52+3.3V

Reserved

GND

USB_D

Pin Definition Pin Definition Pin Definition

1 NC

SATA GND

2 +3.3V

3 NC

SATA GND

+3.3V

4 DGND

DGND

5 NC

TXP (out)

+3.3V

6 NC

+3.3V

7 NC

TXN (out)

8 NC

SATA GND

9 DGND

SATA GND

10 NC

11 NC

SATA GND

12 NC

13 NC

RXN (in)

DA/DSS (option)

14 NC

DGND

15 DGND

RXP (in)

GND

16 NC

DGND

+3.3V

17 NC

SATA GND

18 DGND

Page 23

CT-DBT0X l User’s Manual

2.4.15 Mini-PCIe Slot #2 (MINI_PCIE1)

PCIe x1 & USB 2.0

2.4.16 ATX Power Connector (POWER_CONN)

Connector Type: 1x4-pin pitch 3.96mm wafer connector

2.4.17 PS/2 Keyboard/Mouse Connector (PS2)

Connector Type: 1x6-pin pitch 2.0mm wafer connector

Chapter 2: Jumper & Connectors

Pin Definition Pin Definition Pin Definition

WAKE#

Reserved

+3.3V

Reserved

USB_D+

Reserved

GND39Reserved

GND22PERST#

GND5Reserved

PERn0

Reserved

+1.5V

+3.3Vaux

LED_WWAN#

CLKREQ#

PERp0

Reserved

UIM_PWR

GND44LED_WLAN#

GND27GND45Reserved

UIM_DATA

+1.5V

LED_WPAN#

REFCLK

- 29

GND47Reserved

UIM_CLK

SMB_CLK

+1.5V

REFCLK+

PETn0

Reserved

UIM_RESET

SMB_DATA

GND15GND33PETp0

Reserved

UIM_VPP

GND52+3.3V

Reserved

GND18GND36USB_D

Pin Signal Pin Signal

1 GND 3 +12V 2 GND 4 +12V

Pin Signal Pin Signal

KB_DATA

KB_CLK

+5V4GND

MS_DATA

MS_CLK

Page 24

CT-DBT0X l User’s Manual

2.4.18 SATA Signal Connectors: SATA1-2

Connector Type: 1x4-pin pitch 3.96mm wafer connector

2.4.19 SATA Power Connectors (SATA1/2_PWR)

Connector Type: 4-pin pitch 2.54mm connector

2.4.20 USB 2.0 Pin Header (USB_1/2)

Connector Type: 2x5-pin pitch 2.0mm wafer header connector

Chapter 2: Jumper & Connectors

Pin Signal Pin Signal

USB +5V

USB_D

- 4

USB_D

USB_D+

GND8GND

KEY10N

Pin Signal

GND

SATA_TX+

SATA_TX

GND

SATA_RX

SATA_RX+

GND

Pin Signal

+5V

GND

+12V

Page 25

CT-DBT0X l User’s Manual

2.5 Jumper Settings

2.5.1 Backlight Power (JP1)

2.5.2 Panel Power (JP2)

2.5.3 Clear CMOS (JP8)

Chapter 2: Jumper & Connectors

Function

Setting

Jumper

+12V

-2 closed

+5V (Default)

-3 closed

Function

Setting

Jumper

+3.3V (Default)

-2 closed

+5V

-3 closed

Function

Setting

Jumper

Normal (Default)

-2 closed

Clear CMOS

-3 closed

Page 26

Chapter 3

Features & Interface

Page 27

CT-DBT0X l User’s Manual

3.1 Processor

The cPCI-3620 Series supports the Intel® Atom™ processor E3800 Series which utilizes 22nm process technology with 3-D Tri-Gate transistors to deliver significant improvement in computational

performance and energy-efficiency. Based on a new micro-architecture, the processor is designed for a

one-chip platform. This system-on-chip (SoC) solution platform brings enhanced graphics, greater performance, lower cost, easier validation, and improved x-y footprint to a broad range of intelligent systems. The processor includes an Integrated Display Engine, Processor Graphics and Integrated Memory Controller.

3.2 BIOS

AMI uEFI BIOS on 8MB SPI Flash ROM is used on the CT-DBT0x.

3.3 System Memory

The Integrated Memory Controller (IMC) of the processor supports single channel, non-ECC, unbuffered

DDR3L-1333 memory up to 4 GB with data transfer rates up to 1333MT/s.

3.4 Graphics

The graphics is integrated in the processor and based on Intel® HD Graphics 4000 technology, enabling substantial gains in performance and lower power consumption.

• DirectX 11 support

• OpenGL 4.0 support

• Graphics Base Frequency: 542 MHz

• Graphics Max Dynamic Frequency: 792 MHz

• Full HD video playback

• Maximum resolution of 2560x1600@60Hz

LVDS support is provided by a Realtek RTD2136R-CG DP-to-LVDS converter with dual channel 24-bit

output up to 1920x1200 resolution.

3.5 USB

The CT-DBT0x supports 1x USB 3.0 and 1x USB 2.0 external ports, and 4x internal USB 2.0 ports.

3.6 Ethernet

The CT-DBT0x features 1x 10/100/1000BASE-TX Ethernet by Intel I210IT GbE Controller supporting WOL/PXE.

3.7 SATA

The CT-DBT0x supports 2x SATA 3Gb/s ports.

3.8 Audio

The CT-DBT0x supports HD audio via Realtek ALC886 codec.

Chapter 3: Features & Interface

Page 28

CT-DBT0X l User’s Manual

3.9 Expansion

The CT-DBT0x provides the following expansion interfaces.

• 2x Mini-PCle slots

- Mini PCIe slot #1: PCIe x1 only or mSATA only

- Mini PCIe slot #2: PCIe x1 & USB 2.0

• 1x microSD card slot

• 1x SIM card slot

3.10 General Purpose Input Output

GPI and GPO pins may be implemented as GPIO. GPI and GPO pins may be implemented as SDIO.

3.10.1 GPIO Configuration

Board Design

The GPIO function is provided by a Fintek F81866 AD-I, and it can be accessed through its GPIO index/data port. The index port is the base address +0 and the data port is the base address +1. To access the GPIO register, write index to the index port, and then read/write from/to data port. The configuration on the CT-DBT0x is described as below.

Chapter 3: Features & Interface

Signal

I/O

Description

GPO[

0:3] O

General purpose output pins. Upon a hardware reset, these outputs should be low.

GPI[

0:3] I

General purpose input pins. Pulled high internally on the Module.

Pin# GPIO# Default Configuration

1 ― VCC3

2 ― GND

3 DIO_PH_OUT0 GPO0

4 DIO_PH_IN0 GPI0

5 DIO_PH_OUT1 GPO1

6 DIO_PH_IN1 GPI1

7 DIO_PH_OUT2 GPO2

8 DIO_PH_IN2 GPI2

9 DIO_PH_OUT3 GPO3

10 DIO_PH_IN3 GPI3

Notes:

Output pin default setting is “HIGH”

Index Port 0xA00

Data Port 0xA01

Page 29

CT-DBT0X l User’s Manual

Registers Description

GPIO Input / Output Select

 GPIO8x Configuration Registers

(Index port=0xA00, Data port=0xA01, Offset=0x88)

Note.

Bit X = 0 means Input Mode Bit X = 1 means Output Mode

GPIO Output Data Select

 GPIO Output Data Register

(Index port=0xA00, Data port=0xA01, Offset=0x89)

Note.

Bit X = 0 outputs 0 when in output mode Bit X = 1 outputs 1 when in output mode

3.11 Watchdog Timer

3.11.1 Board Design

The Watchdog Timer (WDT) is implemented by Fintek F81866AD-I.

3.11.2 Psuedo Code

 Set WDT Time Unit (Second Unit)

 Set WDT Timer Value

 Enable WDT

Chapter 3: Features & Interface

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

GPO3 GPO2 GPO1 GPO0 GPI3 GPI2 GPI1 GPI0

Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

GPO3 GPO2 GPO1 GPO0 GPI3 GPI2 GPI1 GPI0

WDT Base Address 0xA10

Step1: ByteData = ReadIOByte(0xA15)

Step2: ByteData = ByteData & 0xF7

Step3: WriteIOByte(0xA15, ByteData)

//Read current setting

//Set time unit to “second”

//Write back

Step1: WriteIOByte(0xA16, Time) //Set watch dog time value

Step1: ByteData = ReadIOByte(0xA15)

Step2: ByteData = ByteData | 0x20

Step3: WriteIOByte(0xA15, ByteData)

//Read current setting

//Enable WDT

//Write back

Page 30

Chapter 4

Driver Installation

Page 31

CT-DBT0X l User’s Manual

Chapter 4: Driver Installation

The drivers for the CT-DBT0x can be found on the driver DVD included with the system.

Install the following drivers in the order listed.

1. Chipset

2. Graphics

3. Audio

4. LAN

5. USB 3.0

6. Intel Serial IO

7. Intel Sideband Fabric Device (Intel MBI)

8. Intel Trusted Execution Engine (Intel TXE)

Page 32

Chapter 5

System BIOS

Page 33

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

The system BIOS software is stored on EEPROM. The BIOS provides an interface to modify the configuration. When the battery is removed, all the parameters will be reset.

Turn on the computer and press <DEL> or <F2> to enter the setup screens.

System Date: MM/DD/YYYY System Time: HH:MM:SS

Use Tab to switch between Date and Time elements.

5.1 Advanced

Page 34

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

5.1.1 ACPI Settings

Enable ACPI Auto Configuration: Enables or disables BIOS ACPI Auto Configuration. Enable Hibernation: Enable or Disable system ability to Hibernate. ACPI Sleep state: Select the highest ACPI sleep state the system will enter when the

SUSPEND button is pressed. Options: Suspend Disable, S3 (Suspend to RAM).

5.1.2 F81866 Super IO Configuration

Enable/disable and configure the serial ports.

Page 35

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

5.1.2.1 Serial Port 1 Configuration

Device Type Select: Choose from RS-232, RS-422 and RS-485.

5.1.2.2 Serial Port 2-4 Configuration

Page 36

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

5.1.3 Hardware Monitor

5.1.4 Serial Port Console Redirection

Serial port console redirection settings.

Page 37

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

5.1.5 CPU Configuration

Intel Virtualization Technology: When enabled, a VMM can utilize the additional hardware

capabilities provided by Vanderpool Technology Execute Disable Bit: XP can prevent certain classes of malicious buffer overflow attacks when

combined with a supporting OS (Windows Server 2003 SP1, Windows XP SP2, SusE Linux 9.2,

RedHat Enterprise 3 Update 3.) Power Technology: Configure the power management features.

Page 38

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

5.1.6 SATA Configuration

The BIOS automatically detects the presence of SATA device and the hardware installed in the SATA ports will be showed in the configuration. Each port can be enabled or disabled individually.

SATA Speed Support: Options: Gen 1, Gen 2. SATA Mode: Select IDE or AHCI Mode SATA Port Hot Plug: Enable/disable the port as Hot Pluggable.

5.1.7 Miscellaneous Configuration

OS Selection: Select the OS.

Page 39

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

5.1.8 LPSS & SCC Configuration

The BIOS automatically detects the presence of SATA device and the hardware installed in the SATA ports will be showed in the configuration. Each port can be enabled or disabled individually.

SCC SD Card Support: Options: Disable, Enable. LPSS I2C #2 Support: Options: Disable, Enable.

5.1.9 Network Stack Configuration

Page 40

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

5.1.10 CSM Configuration

The BIOS automatically detects the presence of SATA device and the hardware installed in the SATA ports will be showed in the configuration. Each port can be enabled or disabled individually.

GateA20 Active:

[Upon Request] – GA20 can be disabled using BIOS services.

[Always] – do not allow disabling GA20; this option is useful when any RT code is

executed above 1MB.

Option ROM Message: Set display mode [Force BIOS] or [Keep Current] for Option ROM. INT19 Trap Response: BIOS reaction on INT19 trapping by Option ROM: IMMEDIATE –

execute the trap right away; POSTPONED – execute the traps during legacy boot. Boot option filter: This option controls what devices system can boot to [UEFI and Legacy], [Legacy only] or [UEFI only]. Option ROM Execution Order: Controls the execution Option ROM, [Do not launch], [UEFI only] or [Legacy only].

Page 41

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

5.1.11 SDIO Configuration

SDIO Access Mode:

Auto Option: Access SD device in DMA mode if controller supports it, otherwise in PIO mode. DMA Option: Access SD device in DMA mode.

PIO Option: Access SD device in PIO mode.

Page 42

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

5.1.12 USB Configuration

Legacy USB Support: Auto option disables legacy support if no USB devices are connected.

Disable option will keep USB devices available only for EFI applications. XHCI Hand-off: This is a workaround for OSes without XHCI hand-off support. The XHCI

ownership change should be claimed by XHCI driver.

EHCI Hand-off: This is a workaround for OSes without EHCI hand-off support. The EHCI ownership change should be claimed by EHCI driver.

USB Mass Storage Driver Support: Enable/Disable USB Mass Storage Driver Support. USB transfer time-out: The time-out value for Control, Bulk, and Interrupt transfers. Device reset time-out: USB mass storage device Start Unit command time-out. Device power-up delay: Maximum time the device will take before it properly reports itself to

the Host Controller. “Auto” uses default value: for a Root port it is 100ms, for a Hub port the

delay is taken from Hub descriptor.

Page 43

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

5.1.13 Security Configuration

XE EOP Message: Send EOP Message Before Enter OS. Intel® AT: Enable/Disable BIOS AT Code from Running. Intel® AT Platform PBA: Enable/Disable BIOS AT Code from Running.

Page 44

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

5.2 Chipset

5.2.1 Northbridge Configuration

Page 45

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

5.2.1.1 Intel IGD Configuration

IGD Turbo Enable: Enable/Disable: IGD Turbo. GFX Boost: Enable/Disable GFX Boost. PAVC: Enable/Disable Protected Audio Video Control. DVMT Pre-Allocated: Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics

Device.

DVMT Total Gfx Mem: Select DVMT 5.0 Total Graphics Memory size used by the Internal Graphics Device. Aperture Size: Select the Aperture Size.

Page 46

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

5.2.1.2 LCD Control

Primary IGFX Boot Display: Default setting is “VBIOS Default”. “CRT”selects VGA, “EFP” selects DisplayPort, “LFP”

selects LVDS.

LCD Panel Type: Default setting is “1024x768 LVDS 24-bit”.

Page 47

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

5.2.2 Southbridge Configuration

High Precision Timer: Enable or Disable the High Precision Event Timer. Restore AC Power Loss: Select AC power state when power is re-applied after a power failure.

5.2.2.1 USB Configuration

Page 48

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

5.2.2.2 PCI Express Configuration

5.3 Security

Administrator’s and User’s passwords could be set. If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be

entered to boot or enter Setup. In Setup, the user will have administrator rights. The minimum length of

the password is 3 and the maximum length is 20.

Page 49

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

5.3.1 Security Boot Menu

Secure Boot: Secure Boot can be enabled if the System running in User mode with enrolled

Platform Key (PK) and CSM function is disabled.

Secure Boot Mode: Secure Boot mode selector. ‘Custom’ Mode enables users to change

Image Execution policy and manage Secure Boot Keys.

Page 50

CT-DBT0X l User’s Manual

Chapter 5: System BIOS

5.4 Boot

Setup Prompt Timeout: Number of seconds to wait for setup activation key. 65535 (0xFFFF)

means indefinite waiting.

Bootup NumLock State: Select [Enable] or [Disable] for the keyboard NumLock state. Quiet Boot: Enables or Disables Quiet Boot option. Boot Order Priorities: Set system boot order.

Hard Drive BBS Priorities: Set the order of the legacy devices in this group.

5.5 Save and Exit

Page 51