Page 1
USER'S MANUAL
Of
Intel Q77 Express Chipset
Based
M/B for LGA 1155 Quad Core Ready
Intel Core Processor
No. G03-NAF93-F
Rev: 1.0
Release date: May 11, 2012
Trademark:
* Specifications and Information contained in this documentation a re furnis hed for i nforma tion use only , a nd are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
Page 2
ii
ENVIRONMENTAL SAFETY INSTRUCTION...........................................................................iii
ENVIRONMENTAL PROTECTION ANNOUCEMENT..............................................................iii
USER’S NOTICE .......................................................................................................................iv
MANUAL REVISION INFORMATION.......................................................................................iv
ITEM CHECKLIST.....................................................................................................................iv
CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD
1-1 SPECIFICATION.........................................................................................................1
1-2 LAYOUT DIAGRAM....................................................................................................2
CHAPTER 2 HARDWARE INSTALLATION
2-1 JUMPER SETTING.....................................................................................................5
2-2 CONNECTORS AND HEADERS................................................................................10
2-2-1 REAR I/O BACK PANEL CONNECTORS....................................................10
2-2-2 MOTHERBOARD INTERNAL CONNECTORS............................................11
2-2-3 HEADER PIN DEFINITION ...........................................................................14
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERNING SETUP...................................................................................................20
3-2 BIOS MENU SCREEN ................................................................................................20
3-3 FUNCTION KEYS .......................................................................................................21
3-4 GETTING HELP ..........................................................................................................21
3-5 MENU BARS...............................................................................................................22
3-6 MAIN MENU................................................................................................................22
3-7 ADVANCED MENU.....................................................................................................23
3-8 CHIPSET MENU..........................................................................................................29
3-9 BOOT MENU...............................................................................................................32
3-10 SECURITY MENU.......................................................................................................33
3-11 SAVE & EXIT MENU...................................................................................................34
TABLE OF CONTENT
Page 3
iii
Environmental Safety Instruction
z Avoid the dusty, humidity and temperature extremes. Do not place the product in
any area where it may become wet.
z 0 to 40 centigrade is the suitable temperature. (The figure comes from the request
of the main chipset)
z Generally speaking, dramatic changes in temperature may lead to contact
malfunction and crackles due to constant thermal expansion and contraction from
the welding spots’ that connect components and PCB. Computer should go
through an adaptive phase before it boots when it is moved from a cold
environment to a warmer one to avoid condensation phenomenon. These water
drops attached on PCB or the surface of the components can bring about
phenomena as minor as computer instability resulted from corrosion and oxidation
from components and PCB or as major as short circuit that can burn the
components. Suggest starting the computer until the temperature goes up.
z The increasing temperature of the capacitor may decrease the life of computer.
Using the close case may decrease the life of other device because the higher
temperature in the inner of the case.
z Attention to the heat sink when you over-clocking. The higher temperature may
decrease the life of the device and burned the capacitor.
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. To minimize
pollution and ensure environment protection of mother earth, please recycle.
Page 4
iv
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED
OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN
PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERI ES AND WE
DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME
WITHOUT NOTICE. MANUFACTURER PROVIDES THIS M ANUAL “AS IS” WITHOUT WARRANTY OF ANY
KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA,
INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.
Manual Revision Information
Reversion Revision History Date
1.0 First Edition May 11, 2012
Item Checklist
5
Motherboard
5
User’s Manual
5
DVD for motherboard utilities
5
Cable(s)
5
I/O Back panel shield
Page 5
1
Chapter 1
Introduction of the Motherboard
1-1 Specification
Spec Description
Design
z ATX form factor; PCB size: 30.0 x24.4 cm
Chipset
z Intel Q77 Express Chipset
LGA1155
CPU Socket
z Supports 3rd and 2nd Generation Intel® Core™ i7, Core™ i5,
Core™ i3 series processor in LAG1155 Package
* for detailed CPU support information please visit our website
Memory Slot
z DDRIII RAM module slot x 4
z Supporting four DDRIII 1600/1333/1066MHz RAM Module
expandable to 32 GB (Maximum)
z Support dual-channel function
Expansion Slots
z 1 pcs* PCI-Express x16 slot
z 1 pcs* PCI-Express x4 slot
z 1 pcs* PCI-Express x1 slot
z 4 pcs *32-bit PCI slot
z 1 pcs* Full-size Mini-PCIE slot/MSATA slot
z 1 pcs*Half-size Mini-PCIE slot
Storage
z Support four SATAII ports
z Support two SATAIII ports
Dual LAN Chip
z Integrated Intel 82574L and 82579LM Gigabit Ethernet LAN chip
that supports Fast Ethernet LAN function of providing
10/100/1000Mbps Ethernet data transfer rate
HD Audio Chip
z Realtek ALC662 6-channel Audio Codec integrated
z Audio driver and utility included
BIOS
z 64MB DIP Flash ROM
Multi I/O
z USB 3.0 port connector x2
z HDMI port connector x1
z Serial port connector x2
z DVI-D port connector x1/VGA port connector x1
z USB 2.0 port connector x4
z RJ-45 LAN connector x2
z Audio connector x3 (Line-in, Line-out, MIC)
z Front panel audio header x1
z HDMI-SPDIF header x1
z CDIN header x1
z Parallel header x1
z TPM 1.2 header x1
z GPIO header x1
z USB 2.0 header x2
z USB 3.0 header x1
z Front panel header x1
z POWER LED header x1
z Speaker header x1
z CIR header x1
z LANLED header x2
z SM_BUS header x1
z TX-RX COM header x 1
z COM port header x 8
Page 6
2
1-2 Layout Diagram
Rear IO Diagram
Motherboard Internal Diagram
RJ-45 LAN Ports
USB 3.0 Ports
Line-IN/
Optical SPDIF OUT
Line-OUT
MIC-IN
USB 2.0 Ports
Serial Port 1
VGA Port
ATX 12V
Power Connector
ATX Powe
r
Connector
LGA1155
CPU Socket
DVI-D Port
HDMI Port
Serial Port 2
Audio Connectors
USB 3.0 PortS over
HDMI port
Serial Port s
(COM1 over COM2)
DVI –D Port over
VGA Port
RJ-45 LAN Ports
Over USB 2.0 Ports
RJ-45 LAN Ports
Over USB 2.0 Ports
USB 3.0 Header
PCI Express x16 Slot (PE1) *
PCI Express 2.0 x 4 Slot
P
CI E
x
p
ress 2.0 x1 Slot
32-bit
P
CI Slots
Front Panel
Audio Heade
r
CDIN Header
Parallel Header
TPM Header
TX-RX COM Heade
r
Intel Q77
Chipset
USB 2.0 Headers
Front Panel Header
DDRIII
DIMM Slot x 4
Full-size Mini-PCIE
/MSATA Slot*
Half-size
Mini-PCIE Slot
E
DP Connector*
SYS FAN2 Header
GPIO Header
SYS FAN1
Header
KBMS Header
CPUFAN Header
SM_BUS Header
CIR Header
Serial Ports (COM3/5/7/9)
SATAIII Ports
SATAII Ports
SATAII Ports
Serial Ports (COM4/6/8/10)
HDMI S/PDIF Header
LAN1LED Header
LAN2LED Header
PWR LED Header
Speaker Header
Page 7
3
*
Note:
1.PE1
slot supports
PCI-Express 2.0 x16
specification when using Intel
®
Sandy Bridge CPU and
supports
PCI-Express 3.0 x1
6 specification when using Intel
®
Ivy Bridge CPU;
2.
mSATA slot is
selectable with full size MINI PCI-E and share with SATA6; 3. EDP connector is only optional for customize
model.
Motherboard Jumper Position
Jumper
Jumper Name Description
JBAT CMOS RAM Clear Function Setting 3-pin Block
JP2 Mini PCI-E Power VCC3.3V/3.3VSB Select 3-pin Block
JP3 (Optional) EDP Panel Power 5V/3.3V Select 3-pin Block
JP1 COM1 Ports Pin9 Function Select 6-pin Block
JP4 COM3 Header Pin9 Function Select 6-pin Block
JP5 COM5 Header Pin9 Function Select 6-pin Block
JP6 COM7 Header Pin9 Function Select 6-pin Block
JP7 COM9 Header Pin9 Function Select 6-pin Block
JP2
CASE_OPEN
J
P1
JBAT
JP7 JP
4
JP
5
JP
11
JP10JP9JP6JP
8
Page 8
4
JP8 COM4 Header Pin9 Function Select 6-pin Block
JP9 COM6 Header Pin9 Function Select 6-pin Block
JP10 COM8 Header Pin9 Function Select 6-pin Block
JP11 COM10 Header Pin9 Function Select 6-pin Block
JP12 COM4 Header RS232/485/422 Function Select 6-pin Block
Case_open Case Open Message Display Function Select 2-pin Block
Connectors
Connector Name
ATXPWR ATX Power Connector
ATX12V1 ATX 12V Power Connector
USB4 USB 3.0 Connector X2
HDMI High-Definition Multimedia Interface
VGA Video Graphic Attach Connector
DVI DVI-D Port Connector
COM1(Top)/COM2(Bottom) Serial Port COM Connector X2
UL1(Middle & Bottom)/UL2(Middle & Bottom) USB 2.0 Port Connector X4
UL1(Top)/UL2(Top) RJ-45 LAN Connector X2
AUDIO1 Audio Connector X3
SATA1_2 SATAIII Connector X2
SATA3_4/SATA5/SATA6 SATAII Connectors X4
EDP (Optional) EDP connector
Headers
Header Name Description
FP_AUDIO Front panel audio Header 10-pin block
CDIN1 CD Audio-In Header 4-pin Block
HDMI_SPDIF HDMI_SPDIF Out Header 2-pin Block
KBMS PS/2 Keyboard & Mouse Header 6-pin Block
SPEAK Speaker Header 4-pin Block
PWRLED Power LED 3-pin Block
JW_FP
(Front Panel Header)
PWR LED/ HD LED/ /Power Button
/Reset
10-pin Block
CIR CIR Header 8-pin Block
USB1 USB 3.0 Header 20-pin Block
USB2/USB3 USB 2.0 Header 10-pin Block
COM 3/4/5/6/7/8/9/10 Serial Port Header 10-pin Block
TX-RXCOM RS 422/485 port headers 4-pin block
GPIO_CON GPIO Header 10-pin Block
TPM TPM Header 20-pin Block
PARALLEL Parallel Port Header 26-pin Block
LAN1LED/LAN2LED LANLED 2-pin Block
SM_BUS SMBUS Header 4-pin Block
SYSFAN1 SYSFAN1 Header 3-pin Block
SYSFAN2/CPUFAN1 FAN Header 4-pin Block
Page 9
5
Chapter 2
Hardware Installation
2-1 Jumper Setting
(1) JBAT (3-pin): Clear CMOS
2-3 Short： Clear CMOS
JBAT
JBAT
1-2 closed : Normal
;
1
3
CMOS Clear Setting
(2)JP2 (3-pin): Mini PCI-E Power VCC 3.3V/3.3 VSB Select
2-3 closed ： MINI PCI-E VCC= 3.3VSB
JP2
JP2
1-2 closed ： MINI PCI -E VCC= 3.3V;
1
3
1
3
(3)JP3 (3-pin): EDP Panel Power 5V/3.3 V Select
2-3 closed ：EDP Panel Pow er=3.3V;
JP3
JP3
1-2 closed ： EDP Panel Power=5V;
1
3
1
3
Page 10
6
*Note:
JP3 is optional for customize model with EDP connector.
(4) JP1 (6-pin): COM1 Port Pin9 Function Select
3-4 closed : +12V;
JP1
1-2 closed: RS232;
1
5-6 closed : +5V
11
(5) JP4 (6-pin): COM3 Port Pin9 Function Select
3-4 closed : +12V;
JP4
1-2 closed: RS232;
1
5-6 closed : +5V
11
(6) JP5(6-pin): COM5 Port Pin9 Function Select
3-4 closed : +12V;
JP5
1-2 closed: RS232;
1
5-6 closed : +5V
11
Page 11
7
(7) JP6(6-pin): COM7 Port Pin9 Function Select
3-4 closed : +12V;
JP6
1-2 closed: RS232;
1
5-6 closed : +5V
11
(8) JP7(6-pin): COM9 Port Pin9 Function Select
3-4 closed : +12V;
JP7
1-2 closed: RS232;
1
5-6 closed : +5V
11
(9) JP8(6-pin): COM4 Port Pin9 Function Select
3-4 closed : +12V;
JP8
1-2 closed: RS232;
1
5-6 closed : +5V
11
Page 12
8
(10) JP9(6-pin): COM6 Port Pin9 Function Select
3-4 closed : +12V;
JP9
1-2 closed: RS232;
1
5-6 closed : +5V
11
(11) JP10(6-pin): COM8 Port Pin9 Function Select
3-4 closed : +12V;
JP10
1-2 closed: RS232;
1
5-6 closed : +5V
11
(12) JP11(6-pin): COM10 Port Pin9 Function Select
3-4 closed : +12V;
JP11
1-2 closed: RS232;
1
5-6 closed : +5V
11
Page 13
9
(13) JP12 (6-pin): COM4 Header RS232/485/422 Function Select
3-4 closed : RS485;
JP12
1-2 closed: RS232;
1
5-6 closed : RS422
1
1
(14) CASE_ OPEN (2-pin): Case Open Message Display Function Select
Pin 1-2 shorted: Case open display function enabled. Use needs to enter BIOS and
enable ‘Case Open Detect’ function. In this case if you case is removed, next time
when you restart your computer a message will be displayed onscreen to inform you
of this.
Page 14
10
2-2 Connectors and Headers
2-2-1 Rear I/O Back Panel Connectors
(1) USB 3.0 Port Connector: USB4
These USB 3.0 connectors are for user to connect USB 3.0 compatible devices
to the system board.
(2) D-Sub 15-pin Connector: VGA
VGA connector is the 15-pin D-subminiature female connector; it is for the
display devices, such as the CRT monitor, LCD monitor and so on.
(3) Digital Visual Interface: DVI
This interface standard designed to maximize the visual quality of digital display
devices such as flat panel LCD computer displays and digital projectors.
(4) High-Definition Multimedia Interface: HDMI
This point-to-point interface is for audio and video signals designed as a
single-cable solution for home theater and consumer electronics equipment.
NOTE! DVI and HDMI Connector can not be used at the same time.
(5) USB 2.0 Port Connector: UL1(Middle & Bottom)/ UL2(Middle & Bottom)
The connectors are 4-pin connector that connects USB devices to the system
board.
(6) RJ-45 LAN Port Connectors: UL1(Top)/UL2(Top)
The connectors are standard RJ-45 connectors for Network.
(7) Serial Port Connector: COM1 (Top)/COM2(bottom)
These two serial ports are for user to connect compatible mouse, modern or
other peripherals.
(8) Audio Line-In, Lin-Out connector: AUDIO1
These Connectors are 3 Phone-Jack for LINE-OUT, LINE-IN, MIC audio
connections.
Line-in: (BLUE)
Audio input to sound chip
Line-out: (GREEN)
Audio output to speaker
MIC: (PINK)
Microphone Connector
RJ-45 LAN Ports
USB 3.0 Ports
Line-IN/
Optical SPDIF OUT
Line-OUT
MIC-IN
USB 2.0 Ports
Serial Port 1
VGA Port
DVI-D Port
HDMI Port
Serial Port 2
Page 15
11
2-2-2 Motherboard Internal Connectors
(1) Power Connector (24-pin block): ATXPWR
ATX Power Supply connector: This is a new defined 24-pins connector that
usually comes with ATX case. The ATX Power Supply allows using soft power
on momentary switch that connect from the front panel switch to 2-pins Power
On jumper pole on the motherboard. When the power switch on the back of the
ATX power supply turned on, the full power will not come into the system board
until the front panel switch is momentarily pressed. Press this switch again will
turn off the power to the system board.
** We recommend that you use an ATX 12V Specification 2.0-compliant power
supply unit (PSU) with a minimum of 350W power rating. This type has 24-pin
and 4-pin power plugs.
** If you intend to use a PSU with 20-pin and 4-pin power plugs, make sure that the
20-pin power plug can provide at least 15A on +12V and the power supply unit
has a minimum power rating of 350W. The system may become unstable or may
not boot up if the power is inadequate.
** If you are using a 20-pin power plug, please refer to Figure1 for power supply
connection. Power plug form power supply and power connectors from
motherboard both adopt key design to avoid mistake installation. You can insert
the power plug into the connector with ease only in the right direction. If the
direction is wrong it is hard to fit in and if you make the connection by force if is
possible.
Figure1：20-pin power plug Figure 2：24-pin power plug
Page 16
12
(2) ATX 12V Power Connector (8-pin block): ATX12V
This is a new defined 8-pin connector that usually comes with ATX Power
Supply. The ATX Power Supply which fully supports AMD AM3 processor must
including this connector for support extra 12V voltage to maintain system power
consumption. Without this connector might cause system unstable because the
power supply can not provide sufficient current for system.
Pin1
4
Pin Definition No. Definition
1 GND 5 +12V
2 GND 6 +12V
3 GND 7 +12V
4 GND 8 +12V
(3) SATAIII Port connector: SATA1_2
These connectors are high-speed SATAIII ports that support 6 GB/s transfer rate.
Pin No. Defnition
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
(4) SATAII Port connector: SATA3_4; SATA5; SATA6
These connectors are high-speed SATAII ports that support 3 GB/s transfer rate.
Pin No. Defnition
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
Page 17
13
(5) EDP(40-pin): EDP Connector
Pin NO. Pin Define Pin NO. Pin Define
Pin 1 NC Pin 21 LCD_GND
Pin 2 GND Pin 22 LCD_GND
Pin 3 EDP_DATA3N Pin 23 EDP_HPD
Pin 4 EDP_DATA3P Pin 24 GND
Pin 5 GND Pin 25 GND
Pin 6 EDP_DATA2N Pin 26 GND
Pin 7 EDP_DATA2P Pin 27 GND
Pin 8 GND Pin 28 EDP_BKLT_EN
Pin 9 EDP_DATA1N Pin 29 EDP_BKLT_PWM
Pin 10 EDP_DATA1P Pin 30 NC
Pin 11 GND Pin 31 NC
Pin 12 EDP_DATA0N Pin 32 BKLT_PWR
Pin 13 EDP_DATA0P Pin 33 BKLT_PWR
Pin 14 GND Pin 34 BKLT_PWR
Pin 15 EDP_AUXP Pin 35 BKLT_PWR
Pin 16 EDP_AUXN Pin 36 NC
Pin 17 GND Pin 37 NC
Pin 18 LCD_VCC Pin 38 NC
Pin 19 LCD_VCC Pin 39 NC
Pin 20 NC Pin 40 NC
*Note:
EDP connector is only optional for customized model.
Page 18
14
2-2-3 Header Pin Definition
(1) FP_AUDIO (10-pin): Line-Out, MIC-In Header
This header is connected to Front Panel Line-out, MIC connector with cable.
Line-Out, MIC Header
FP_AUDIO
Pin 1
MIC1-R
LINE OUT-L
MIC1-L LI NE OUT- R
NC
GND
NC
NC
NC
2
(2) CDIN1(4-pin): CD AUDIO-In Header
CDIN header is for CD-Audio Input signal. Please connect it to CD-ROM
CD-Audio output connector.
Pin1
GND
CD-R
CD-L
GND
(3) HDMI_SPDIF(2-pin): HDMI-SPDIF Out header
HDMI_SPDIF Header
Pin1
SPDIF
GND
Page 19
15
(4) KBMS (6-pin): PS/2 Keyboard & Mouse Header
GND
KB CLK
KB
_
DATA
Pin1
MS
_
DATA
VCC
MS CLK
(5) SPEAK (4-pin): Speaker Header
This 4-pin header connects to the case-mounted speaker. See the figure below.
(6) PWR LED(3-pin): PWR LED Header
The Power LED is light on while the system power is on. Connect the Power LED
from the system case to this pin header.
SPEAK
SPEAK
NC
NC
VCC
Pin 1
PWRLED
Pin 1
VCC
GND
GND
(7) JW-FP(10-pin): Front Panel Header
HDL ED
RESET
HDDLED+
GND
PWRLED+
PWRBTN
GND
PWRLED-
HDDLED-
RSTSW
V
CC
PWRBT
Pin 1
2
PWR LED
Page 20
16
(8) CIR (8-Pin): CIR Header
CIR He ader
GND
NC
ATX 5VSB
CIR L ED
V
CC
CIR _WB
2
Pin 1
CIR RX
(9) USB 3.0 Port Header (20-pin): USB1
This USB 3.0 header is used for connecting the additional USB 3.0 port plugs. By
attaching an optional USB 3.0 cable, your can be provided with two additional
USB 30 plugs affixed to the back panel.
SSRX2-
SSRX2+
GND2
SSTX2 -
SSTX2+
GND3
D2-
D1+
VBUS
11
Pin 1
10
20
VBUS
SSRX1
-
SSRX1+
GND0
SSTX1-
SSTX1+
GND1
D1-
D1+
NC
(10) USB 2.0 Port Headers (10-pin): USB2/USB3
These headers are used for connecting the additional USB 2.0 port plugs. By
attaching an option USB cable, your can be provided with two additional USB 2.0
plugs affixed to the back panel.
Pin 1
V
CC
-DATA
GND
+DATA
V
CC
NC
-DAT A
GND
+DATA
Page 21
17
(9) COM3/4/5/6/7/8/9/10 (10-Pin): Serial Port Header
DCD
Pin1
Pin6
Pin5
SIN
SOUT
DTR
GND
DSR
RTS
CTS
RI
(10) TX-RXCOM (4-pin): RS422/485 Header
Pin 1
TXDN
RXDP
TXDP
3
RXDN
2
4
(11) GPIO_CON (10-pin): GPIO Header
9
GPIO
_
30
GND
GPIO_32
GPIO_34
GPIO_36
GPIO
_
31
GPIO_33
2
Pin 1
10
VCC
GPIO_35
GPIO
_
37
Page 22
18
(12) TPM Header (20-pin):TPM
19
CLK
VCC3.3
LFRAME-
RESET
LAD3
GND
VCC5V
KEY/NC
2
Pin 1
20
LAD2
LAD1
LAD0
SMB_CLK
SB 3.3V
GND
GND
SMB_DATA
SERIRQ
NC/GND
GPIO
LPC_PD-
(13) PARALLEL (26-pin): Parallel Port Header
Pin 1
Parallel Header
Pin 2
Pin NO. Pin Definition Pin NO. Pin Definition
Pin 1
STB-
Pin 2
AFD-
Pin 3
PD0
Pin 4
ERR-
Pin 5
PD1
Pin 6
INIT-
Pin 7
PD2
Pin 8
SLIN-
Pin 9
PD3
Pin 10
GND
Pin 11
PD4
Pin 12
GND
Pin 13
PD5
Pin 14
GND
Pin 15
PD6
Pin 16
GND
Pin 17 PD7 Pin 18 GND
Pin 19 ACK- Pin 20 GND
Pin 21 BUSY Pin 22 GND
Pin 23 PE Pin 24 GND
Pin 25 SLCT Pin 26 No Key
Page 23
19
(14)LAN1LED/LAN2LED (2-pin): LANLED Header
Pin1
LED-
LED+
(15)SM_BUS (4-pin): SM BUS Header
Pin 1
V
CC5V
SMBUS CLK
SMBUS DATA
GND
(16) SYSFAN1 (3-pin), SYSFAN2 (4-pin), CPUFAN1 (4-pin): FAN Headers
SYSFAN1
Control
Fan Clock
+12V Fan Power
Pin1
GND
Pin1
GND
+12V F an Po we r
Fan Clock
CPUFAN
Pin1 GND
+12V Fan Power
Fan Clock
SYSFAN2
Control
Page 24
20
Chapter 3
Introducing BIOS
Notice!
The BIOS options in this manual are for reference only. Different
configurations may lead to difference in BIOS screen and BIOS
screens in manuals are usually the first BIOS version when the board
is released and may be different from your purchased motherboard.
Users are welcome to download the latest BIOS version form our
official website.
The BIOS is a program located on a Flash Memory on the motherboard. This program
is a bridge between motherboard and operating system. When you start the computer,
the BIOS program will gain control. The BIOS first operates an auto-diagnostic test
called POST (power on self test) for all the necessary hardware, it detects the entire
hardware device and configures the parameters of the hardware synchronization.
Only when these tasks are completed done it gives up control of the computer to
operating system (OS). Since the BIOS is the only channel for hardware and software
to communicate, it is the key factor for system stability, and in ensuring that your
system performance as its best.
3-1 Entering Setup
Power on the computer and by pressing <Del> immediately allows you to enter Setup.
If the message disappears before your respond and you still wish to enter Setup,
restart the system to try again by turning it OFF then ON or pressing the “RESET”
button on the system case. You may also restart by simultaneously pressing <Ctrl>,
<Alt> and <Delete> keys. If you do not press the keys at the correct time and the
system does not boot, an error message will be displayed and you will again be asked
to
Press
<Del>
to enter Setup
3-2 BIOS Menu Screen
The following diagram show a general BIOS menu screen:
Page 25
21
BIOS Menu Screen
3-3 Function Keys
In the above BIOS Setup main menu of, you can see several options. We will explain
these options step by step in the following pages of this chapter, but let us first see a
short description of the function keys you may use here:
z
Press←→ (left, right) to select screen;
z
Press ↑↓ (up, down) to choose, in the main menu, the option you want to confirm
or to modify.
z
Press <Enter> to select.
z
Press <+>/<–> keys when you want to modify the BIOS parameters for the active
option.
z
[F1]: General help.
z
[F2]: Previous value.
z
[F3]: Optimized defaults.
z
[F4]: Save & Reset.
z
Press <Esc> to quit the BIOS Setup.
3-4 Getting Help
Main Menu
The on-line description of the highlighted setup function is displayed at the top right
corner the screen.
Status Page Setup Menu/Option Page Setup Menu
Menu Bar
Menu Items
Current Setting Value
Function Keys
General Help Items
Page 26
22
Press F1 to pop up a small help window that describes the appropriate keys to use
and the possible selections for the highlighted item. To exit the Help Window, press
<
Esc
>.
3-5 Menu Bars
There are six menu bars on top of BIOS screen:
Main To change system basic configuration
Advanced To change system advanced configuration
Chipset To change chipset configuration
Boot To change boot settings
Security Password settings
Save & Exit Save setting, loading and exit options.
User can press the right or left arrow key on the keyboard to switch from menu bar.
The selected one is highlighted.
3-6 Main Menu
Main menu screen includes some basic system information. Highlight the item and
then use the <+> or <-> and numerical keyboard keys to select the value you want in
each item.
System Date
Set the date. Please use [Tab] to switch between data elements.
System Time
Set the time. Please use [Tab] to switch between time elements.
Page 27
23
3-7 Advanced Menu
Scroll down to view more setting options:
Legacy OpROM Support
Launch External PxE OpROM/Launch LAN1 PXE OpROM/Launch LAN2 PXE
OpROM
Use this item to enable or disable boot option for legacy network devices.
Launch Storage OpROM
Use this item to enable or disable boot options for legacy mass storage devices with
option ROM.
ERP Function
Use this item to enable or disable ERP function for this board. This item should be set
as [Disabled] if you wish to have Active All Wakeup Function.
► PCI Subsystem Settings
Press [Enter] to enter and make settings for the following sub-items:
PCI 64bit Resources Handing:
Above 4G Decoding
Use this item to enable or disable 64bit capable devices to be decoded in above
4G address space(only if system support 64 bit PCI decoding).
Page 28
24
PCI Common Settings:
PCI Latency Timer
Use this item to set value to be programmed into PCI latency timer register.
VGA Palette Snoop
Use this item to enable or disable VGA palette registers snooping.
PERR# Generation
Use this item to enable or disable PCI device to generate PERR#.
SERR# Generation
Use this item to enable or disable PCI device to generate SERR#.
▶ PCI Express Settings
Press [Enter] to make settings for the following sub-items:
PCI Express Device Register Settings:
Relaxed Ordering
Use this item to enable or disable PCI express device relaxed ordering.
Extended Tag
If set as [Enabled] it will allow device to use 8-bit tag field as a requester.
No Snoop
Use this item to enable or disable PCI Express device No Snoop option.
Maximum Payload
Use this item to set maximum payload of PCI Express device or allow system
BIOS to select the value.
Maximum Read Request
Use this item to set maximum read request size of PCI Express device or allow
system BIOS to select the value.
PCI Express Link Register Settings:
ASPM Support
The optional settings: [Disabled]; [Auto]; [Force L0s].
Extended Synch
If set as [Enabled] it will allow generation of extended synchronization patterns.
Link Training Retry
Use this item to define number of retry attempts software will take to retrain the
link if previous training attempt was unsuccessful.
Link Training Timeout(uS)
Use this item to define number of microseconds software will wait before polling
‘Link Training’ bit in link status register. Value range from 10 to 1000 uS.
Unpopulated Links
The optional settings are: [Keep Link On]; [Disable Link]. In order to save power,
software will disable unpopulated PCI Express links if this option is set as ‘Disable
Link’.
► ACPI Settings
Press [Enter] to make settings for the following sub-items:
ACPI Settings:
ACPI Sleep State
Use this item to select the highest ACPI sleep state the system will enter when the
suspend button is pressed.
Page 29
25
S3 Video Repost
Use this item to enable or disable S3 video report.
► Wakeup Function Settings
Press [Enter] to make settings for the following sub-items:
Wake System with Fixed Time
Use this item to enable or disable system wake on alarm event. When set as
[Enabled], system will wake on the hour/min/sec specified.
CIR Wakeup
Use this item to enable or disable CIR wakeup.
PS2 KB/MS Wakeup
Use this item to enable or disable PS2 KB/MS wakeup. This function is only
supported when ERP function is disabled.
PCI PME Wakeup
Use this item to enable or disable S3/S4/S5 PCI PME Wakeup. This function is
only supported when ERP function is disabled.
USB S3/S4 Wakeup
Use this item to enable or disable USB S3/S4 wakeup. This function is only
supported when ERP function is disabled.
► Trusted Computing
Press [Enter] to enable or disable TPM support.
► CPU Configuration
Press [Enter] to make settings for the following sub-items:
Hyper-Threading
The optional settings are: [Disabled]; [Enhanced].
Active Processor Cores
Use this item to select number of cores to enable in each processor package.
Limit CPUID Maximum
The optional settings are: [Disabled]; [Enhanced].This item should be set as
[Disabled] for Windows XP.
Execute Disable Bit
The optional settings are: [Disabled]; [Enhanced].
Intel Virtualization Technology
The optional settings: [Enabled]; [Disabled].
When set as [Enabled], a VHM can utilize the additional hardware capabilities
provided by Vanderpool Technology.
Hardware Prefetcher
Use this item to turn on/off the Mid Level Cache (L2) streamer prefetcher.
Adjacent Cache Line Prefetch
Use this item to turn on/off prefetching of adjacent cache lines.
► SATA Configuration
Press [Enter] to make settings for the following sub-items:
SATA Controller(s)
The optional settings are: [Disabled]; [Enhanced].
SATA Mode Selection
The optional settings are: [IDE]; [AHCI]; [RAID].
Page 30
26
► Intel(R) Rapid Start Technology
Use this item to enable or disable Intel(R) Rapid Start Technology
► PCH-FW Configuration
Press [Enter] to see ME information and make settings for Firmware Update
Configuration.
Firmware Update Configuration
Press [Enter] to make settings for ME FW Image RE-Flash.
ME FW Image RE-Flash
Use this item to enable or disable ME FW Image Re-Flash function.
► AMT Configuration
Use this item to configure Active Management Technology parameters.
Press [Enter] to make settings for the following sub-items:
Intel AMT
Use this item to enable or disable Intel Active Management Technology.
BIOS Hotkey Pressed
The optional settings are: [Disabled]; [Enabled].
MEBx Selection Screen
The optional settings are: [Disabled]; [Enabled].
Hide Un-Configure ME Confirmation
The optional settings are: [Disabled]; [Enabled].
MEBx Debug Message Output
The optional settings are: [Disabled]; [Enabled].
Un-Configure ME
The optional settings are: [Disabled]; [Enabled].
Amt Wait Timer
Use this item to set time to wait before sending ASF_GET_BOOT_OPTIONS.
Disable ME
The optional settings are: [Disabled]; [Enabled].
ASF
Use this item to enable or disable alert specification format.
Active Remote Assistance Process
The optional settings are: [Disabled]; [Enabled].
USB Configure
Use this item to enable or disable USB configure function.
PET Progress
Use this item to enable or disable PET events progress to receive PET event or
not.
► USB Configuration
Press [Enter] to make settings for the following sub-items:
Legacy USB Support
The optional settings are: [Auto]; [Disabled]; [Enabled].
EHCI Hand-off
The optional settings are: [Disabled]; [Enabled].
USB hardware delay and time-out:
USB Transfer time-out
Use this item to set the time-out value for control, bulk, and interrupt transfers.
Page 31
27
Device reset time-out
Use this item to set USB mass storage device start unit command time-out.
Device power-up delay
Use this item to set maximum time the device will take before it properly reports
itself to the host controller. ‘Auto’ uses default value: for a root port it is 100 ms, for
a hub port the delay is taken from hub descriptor. The optional settings: [Auto];
[Manual].Select [Manual] you can set value for the following sub-item: Device
Power-up delay in seconds, the delay range in from 1 to 40 seconds, in one
second increments.
Mass Storage Devices:
Generic Flash Disk 8.07
The optional settings are: [Auto]; [Floppy]; [Forced HDD]; [Hard Disk]; [CD-ROM].
► SMART Settings
Press [Enter] to make settings for SMART Self Test. The optional settings are:
[Disabled]; [Enabled].
► Super I/O Configuration
Press [Enter] to make settings for the following sub-items:
Super IO Configuration
► COM1 Port Configuration
Press [Enter] to make settings for the following items:
Serial Port
Use this item to enable or disable serial port (COM).
Change Settings
Use this item to select an optimal setting for super IO device.
► COM2 Port Configuration
Press [Enter] to make settings for the following sub-items:
Serial Port
Use this item to enable or disable serial port (COM).
Change Settings
Use this item to select an optimal setting for super IO device.
► Parallel Port Configuration
Parallel port
Use this item to enable or disable Parallel port (LPT/LPTE)
Change Settings
Use this item to select an optimal setting for super IO device.
Device Mode
Use this item to change the Printer Port.
CIR Controller
Use this item to enable or disable CIR controller.
Case Open Detect
Use this item to detect case has already open or not, show message in POST.
► PC Health Status
Press [Enter] to view hardware health status.
Page 32
28
► Second Super IO Configuration
► COM3/COM4/ COM5/COM6 Configuration
Serial Port
Use this item to enable or Disable serial port (COM).
Change Settings
Use this item to select an optimal setting for super IO device.
Serial Port Mode Select
Use this item to set serial port as [RS232] or [RS422/485].
*Note: Serial Port Mode Select function is only optional for COM4 port.
► Third Super IO Configuration
► COM7/COM8/COM9/COM10 Configuration
Serial Port
Use this item to enable or Disable serial port (COM1).
Change Settings
Use this item to select an optimal setting for super IO device.
► WatchDog Configuration
Press [Enter] to make settings for Watchdog Configuration:
Watchdog Configuration:
WatchDog Timer Control
Use this item to enable or disable WatchDog Timer Control. When set as
[Enabled], the following sub-items shall appear:
WatchDog Timer Val
User can set a value in the range of 4 to 255.
WatchDog Timer Unit
The optional settings are: [Second];[Minute].
► Chipset Voltage Configuration
Use this item to choose the Voltage Parameters. Press [Enter] user can make
settings for DRAM Voltage.
► Shutdown Temperature Configuration
Use this item to select system shutdown temperature.
► CPU PPM Configuration
Press [Enter] to make settings for CPU PPM Configuration:
CPU PPM Configuration:
EIST
Use this item to enable or disable Intel SpeedStep.
CPU C3 Report
Use this item to enable or disable CPU C3 (ACPI C2) report to OS.
CPU C6 Report
Use this item to enable or disable CPU C6 (ACPI C3) report to OS.
► SmartFan Configuration
Press [Enter] to make settings for SmartFan Configuration:
CPUFAN / SYSFAN1/ SYSFAN2 Smart Mode
When set as [Enabled], the following sub-items shall appear:
CPUFAN / SYSFAN1/ SYSFAN2 Full Speed Temp
Page 33
29
Use this item to set CPUFAN/SYSFAN1/SYSFAN2 full speed temp. Fan will run at
full speed when above this temperature.
CPUFAN / SYSFAN1/ SYSFAN2 Idle Temp
Use this item to set CPUFAN/SYSFAN1/SYSFAN2 idle speed temperature. Fan
will run at idle speed when below this temperature.
SYSFAN1/ SYSFAN2 Stop Temp
Use this item to set SYSFAN1/SYSFAN2 stop temp. Fan will stop when below this
temperature.
SYSFAN2 3/4 Pin Fan Select
The optional settings are: [3 pin]/ [4 pin Fan].
3-8 Chipset Menu
► PCH-IO Configuration
Press [Enter] to make settings for the following sub-items:
► USB Devices Configuration
Press [Enter] to further setting USB device configuration.
USB Device Configuration:
XHCI Pre-Boot Driver
Use this item to enable or disable XHCI Pre-Boot Driver Support.
XHCI Mode
The optional settings are: [Smart Auto]; [Auto]; [Enabled];[Disabled].
HS Port #1 Switchable/ HS Port #2 Switchable/HS Port #3 Switchable/HS Port
#4 Switchable
The optional settings are: [Disabled]; [Enabled].These items allow for HS port
switching between XHCI and EHCI. If set as [Disabled], port is routed to EHCI.
*Note: The above items shall not appear when XHCI Mode is set as [Disabled].
XHCI Streams
The optional settings are: [Disabled]; [Enabled].Use this item to enable or disable
Page 34
30
XHCI Maximum Primary Stream Array Size.
*Note: The above item shall not appear when XHCI Mode is set as [Disabled].
EHCI1/ EHCI2
Use this item to enable or disable USB EHCI (USB 2.0) support. One EHCI
controller must always be enabled. The optional settings are: [Enabled];
[Disabled].
USB Port Pre-Port Disable Control
Use this item to control each of the USB ports (0~13) disabling.
► PE2 Configuration/ PE3 Configuration/Mini PCIE Slot Configuration
Press [Enter] to make settings for PE2/PE3/ Mini PCIE slot configuration.
PE2 Slot/ PE3 Slot/Mini PCIE Slot
Use this item to control corresponding PCI Express Root Port.
ASPM Support
Use this item to set the ASPM level. The optional settings are: [Disabled]; [L0s];
[L1]; [L0SL1]; [Auto].
URR
Use this item to enable or disable PCI Express unsupported request reporting.
FER
Use this item to enable or disable PCI Express device Fatal Error Reporting.
NFER
Use this item to enable or disable PCI Express device Non-Fatal Error Reporting.
CER
Use this item to enable or disable PCI Express device Correctable Error
Reporting.
CT0
Use this item to enable or disable PCI Express Completion Timer T0.
SEFE
Use this item to enable or disable Root PCI Express System Error on Fatal Error.
SENFE
Use this item to enable or disable Root PCI Express System Error on Non-Fatal
Error.
SEGE
Use this item to enable or disable Root PCI Express System Error on Correctable
Error.
PME SCI
Use this item to enable or disable PCI Express PME SCI.
Hot Plug
Use this item to enable or disable PCI Express Hot Plug.
PCIe Speed
Use this item to select PCI Express port speed.
Extra Bus Reserved
Use this item to set extra bus reserved (0-7) for bridges behind this root bridge.
Reserved Memory
Use this item to set reserved memory and prefetchable memory (1-20MB) range
for this root bridge.
Reserved I/O
User this item to set reserved I/O (4L/8K/12K/16K/20K) range for this root bridge.
Page 35
31
Azalia HD Audio
The optional settings are: [Disabled]; [Enabled];[Auto].
Azalia Internal HDMI Codec
Use this item to enable or disable internal HDMI codec for Azalia.
Onboard LAN1 Controller
Use this item to enable or disable onboard LAN controller.
Wake on LAN1 from S5
Use this item to enable or disable integrated LAN to wake the system.
Onboard LAN2 Device
Use this item to control the PCI Express root port.
DeepSx Power Policies
Use this item to configure the Deep Sx Mode configuration.
High Precision Event Timer Configuration
High Precision Timer
The optional settings are: [Enabled]; [Disabled].
Restore AC Power Loss
Use this item to select AC power state when power is re-applied after a power
failure. The optional settings are: [Power Off]; [Power On]; [Last State].
► System Agent (SA) Configuration
Press [Enter] to make settings for the following sub-items:
Enable NB Card
The optional settings are: [Enabled]; [Disabled].
► Graphics Configuration
Press [Enter] to make further settings for Graphics Configuration.
Graphics Configuration
Primary Display
The optional settings are: [Auto]; [IGFX]; [PEG]; [PCI].
Internal Graphics
The optional settings are: [Auto]; [Disabled]; [Enabled].
CTT Size
The optional settings are: [1MB]; [2MB].
Aperture Size
The optional settings are: [128MB]; [256MB]; [512MB].
DVMT Pre-Allocated
Use this item to select DVMT 5.0 pre-allocated (fixed) graphics memory size used
by the internal graphics device.
DVMT Total Gfx Mem
Use this item to select DVMT 5.0 total graphics memory size used by the internal
graphics device.
GFx Low Power Mode
The optional settings are: [Disabled]; [Enabled].This option is applicable for SFF
only.
LCD Control
Primary IGFX Boot Display
The optional settings are:[VBIOS default]; [CRT]; [HDMI].
Secondary IGFX Boot Display
The optional settings are: [Disabled]; [CRT]; [HDMI].
Page 36
32
* Note: The above item shall appear when Primary IGFX Boot Display set as
[CRT] or [HDMI].
► NB PCIe Configuration
Press [Enter] to make settings for the following sub-items:
NB PCIe Configuration:
PEG0-Gen X
The optional settings are: [Auto]; [Gen1]; [Gen2]; [Gen3].
PEG0 ASPM
The optional settings are: [Disabled]; [Auto]; [ASPM L0s]; [ASPM L1]; [ASPM
L0sL1].
Enable PEG
The optional settings are: [Auto];[Enabled]; [Disabled].
De-emphasis Control
The optional settings are: [-6 dB]; [-3.5 dB].
► Memory Configuration
Press [Enter] to make settings for the following sub-items:
DIMM profile
Use this item to select DIMM timing profile that should be used.
Memory Frequency Limiter
Use this item to set maximum memory frequency selection in Mhz.
MMode Support
The optional settings are: [Auto]; [1N Mode]; [2N Mode].
Memory Remap
Use this item to enable or disable memory remap above 4G. The optional settings
are: [Enabled]; [Disabled].
3-9 Boot Menu
Page 37
33
Boot Configuration:
Setup Prompt Timeout
Use this item to set number of seconds to wait for setup activation key.
Bootup Numlock State
Use this item to select keyboard numlock state. The optional settings are: [On]; [Off].
Quiet Boot
The optional settings are: [Enabled]; [Disabled].
Fast Boot
The optional settings are: [Enabled]; [Disabled].
Gate A20 Active
The optional settings are: [Upon Request]; [Always].
Option ROM Message
Use this item to set display mode for option ROM. The optional settings are: [Force
BIOS]; [Keep Current].
Interrupt 19 Capture
The optional settings are: [Enabled]; [Disabled].
Boot Option Priorities:
Boot Option #1/ Boot Option #2
Use this item to decide system boot order from available options.
Hard Drive BBS Priorities
Use this item to set the order of the legacy devices in this group.
3-10 Security Menu
Security menu allow users to change administrator password and user password
settings.
Page 38
34
3-11 Save & Exit Menu
Save Changes and Reset
This item allows user to reset the system after saving the changes.
Discard Changes and Reset
This item allows user to reset the system without saving any changes.
Restore Defaults
Use this item to restore /load default values for all the setup options.
Save as User Defaults
Use this item to save the changes done so far as user defaults.
Restore User Defaults
Use this item to restore defaults to all the setup options.
Launch EFI Shell from file system device
This item is for attempts to launch EFI shell application (Shell x64.efi) from one of the
available filesystem devices.
Loading...