C&T Solution ACO-3000-4L-M12-5010U, ACO-3000-4L-5010U, ACO-3000-4P-5350U, ACO-3000-4L-M12-3765U, ACO-3000-4P-5010U User Manual
...Page 1
ACO-3000 Series
Vehicle Applied Fanless System
Page 2
ACO-3000 l User’s Manual
Table of Contents
Prefaces …………………………………………………….……………………………………………. 04
Revision …………………………………………………………………………………………..……………….……….. 04
Disclaimer ………………………………………………………..…….…….………………………….……………….. 04
Copyright Notice …………………………………….…………………….…………………………………………… 04
Trademarks Acknowledgment …………..………………………………………………………...................04
Environmental Protection Announcement …………………………….………………….……………….. 04
Safety Precautions ………………………………………….……………………………….…………….………….. 05
Technical Support and Assistance …………………………………….…………….…………….…………….06
Conventions Used in this Manual ………………………………………………………………….….………..06
Package Contents …………………………………………………………………………………………….…………07
Ordering Information …………………………………….……………………………………….……….………… 08
Optional Accessory …………...……………………………………..................................................... 11
Chapter 1 Product Introductions ………………………………………………………..… 12
1.1 Overview ……………………….………………………………..………….………………………….. 13
1.1.1 Key Feature ………….……………………………………….……….…..…………….......13
1.2 Hardware Specification ….………………………….....…………….…………..………………14
1.3 System I/O ……………………………..……………………..…………………………………………15
1.3.1 ACO-3000 ………………….…………......................……………………………………15
1.3.2 ACO-3000-4L(P) …………………………………….…….……………….………………...17
1.3.3 ACO-3000-4L(P)-M12 ……..…………………….…….……………….………………...19
1.3.4 ACO-3011E(P) …….…………..…………………….…….……………….………………...21
1.3.5 ACO-3011E-4L(P) / ACO-3011P-4L(P) ……………..…………...………………... 23
1.3.6 ACO-3011E-4L(P)-M12 / ACO-3011P-4L(P)-M12 ……….…………………... 25
1.3.7 ACO-3022EE(PP) …….…………..…………………….……………….…..……………... 27
1.3.8 ACO-3022EE-4L(P) / ACO-3022PP-4L(P) …………..……….….………………...29
1.3.9 ACO-3022EE-4L(P)-M12 / ACO-3022PP-4L(P)-M12 ……….…..…………... 31
1.4 Mechanical Dimension …………………………..…………………………..………….………. 33
1.4.1 ACO-3000 / ACO-3000-4L(P) / ACO-3000-4L(P)-M12 ..………………….… 33
1.4.2 ACO-3011E(P) / ACO-3011E(P)-4L(P) / ACO-3011E(P)-4L(P)-M12 ..…. 34
1.4.3 ACO-3022EE(PP) / ACO-3022EE(PP)-4L(P) /
ACO-3022EE(PP)-4L(P)-M12 ………………………………………………………..….35
Chapter 2 Jumpers and Connectors ………………………………………………………. 36
2.1 Switch and connector Locations ………………………………………..…….……………....37
2.1.1 Top View ………………………………………………………………………..……………… 37
2.1.2 Bottom View ………………………………………………………………………..………..38
2.2 Connector / Switch Definition ……………………………….……….…….……….............39
2.3 Switch Definitions ………….……………...............................................................40
2.4 Connector Definitions ………………………….......................................................42
Chapter 3 System Setup …………………………..…………………………………………… 52
3.1 Set torque force to 3.5 kgf-cm to execute all the screwing and
unscrewing …………………………………………………………………………………………….. 53
3.2 Removing chassis bottom cover ……...……………..……………………..………..……... 53
3.3 Removing chassis top cover ……….….…………………….……………….……………….… 54
3.4 Installing SODIMM ……………………………………………….…………………….…………....55
3.5 Installing Mini PCIe card / mSATA …….…………………….……..….……………….……..56
3.6 Installing antenna ………………..……………………………………………………..…………... 57
3.7 Assemble chassis top cover …..……………………………………………………...............59
2
Page 3
ACO-3000 l User’s Manual
3
3.8 Installing HDD on internal SATA HDD bay……………..…………………..………..….... 61
3.9 Installing HDD on removable SATA HDD bay……………..……….……..………..….... 63
3.10 Assemble chassis bottom cover …….…...…..….………………………………………….. 65
3.11 Installing SIM card …….…………..….……………..….………………………………………….. 66
3.12 To Configure Power Ignition Settings …….…………..….…..…...…………………..….. 67
3.13 Installing Wall Mount Kit ….…………..….…..…...………………………………………….. 68
3.14 Installing DIN rail holder …….…………..….…..…...…………………………………………..69
Chapter 4 BIOS Setup …………………………………………………………………………… 70
4.1 BIOS Introduction …….……….……………………………………..….…….…..….…………...71
4.2 Main Setup ……..……….………………….…………………………..…….….………………......72
4.2.1 System Language …….……………………………………..……..…………………….... 72
4.2.2 System Date …….……………………………………………..……..……………………....72
4.2.3 System Time ………..…………………………………………..……….…………………... 72
4.3 Advanced Setup ………………………………………………………..…………………………….. 73
4.3.1 CPU Configuration …………………………………………….…………..………………. 73
4.3.2 ACPI Settings …………………………….………..………………………………….……... 74
4.3.3 AMT Configuration ………..……………………………….………………………..….... 75
4.3.4 Super IO Configuration ……………..………………………………....……..……..... 76
4.3.5 Hardware Monitor ……………………………….…………….………….….…….….... 79
4.3.6 Serial Port Console Redirection .…………………………..…………..………..... 79
4.3.7 SATA Configuration ……..………………………………..………………………….......80
4.3.8 Network Stack Configuration ……….…………………………………..………….... 81
4.3.9 CSM Configuration ………………………………………………..………………………. 82
4.3.10 USB Configuration …………………………………………………………………..……..83
4.3.11 Intel(R) Ethernet Connection I218-LM-XX:XX:XX:XX:XX:XX ……..…….. 84
4.3.12 Intel(R) I210 Gigabit Network Connection- XX:XX:XX:XX:XX:XX …….. 85
4.4 Chipset …………...……….………………….…..….…..………………………………………..…....86
4.4.1 System Agent (SA) Configuration ………………………………..…………………..86
4.4.2 PCI-IO Configuration ………………………………………………..……………………..88
4.5 Security …………...……….………………….…..….…..………………………………..…………...91
4.5.1 Administrators Password …….…………………………………..……………………..91
4.5.2 Users Password …….……………………………….………………..…………………….. 91
4.6 Boot …………...……….….………………….…..…………………………..…………..……………...92
4.6.1 Setup Prompt Timeout ………………………..…………..……………………………..92
4.6.2 Bootup NumLock State ………………………………………………..………………… 92
4.6.3 Full Screen Logo Show ………………………….…………………………..…...……… 92
4.6.4 Fast Boot ……………………………….……………..………………………..……………... 92
4.6.5 Hard Driver BBS Priorities ……………………..………………………..……………...92
4.7 Save & Exit …...……….….………………….…..….…..……………………………..…………..... 93
4.7.1 Save Changes and Reset ……………..………………………………..……..……......93
4.7.2 Discard Changes and Reset …………………………………............……………….93
4.7.3 Restore Defaults ……………………………………………………………..……………...93
4.7.4 Launch EFI Shell from filesystems device ………………………………..……… 93
Appendix WDT & GPIO …………………………………………………………………………… 94
WDT Sample Code …….……………………….……………….……………..….…….…….…………... 95
GPIO Sample Code ………………………………………………………..…………………………………. 96
Page 4
ACO-3000 l User’s Manual
4
Revision
Disclaimer
All specifications and information in this User’s Manual are believed to be accurate and up to date. C&T
Solution Inc. does not guarantee that the contents herein are complete, true, accurate or non-misleading.
The information in this document is subject to change without notice and does not represent a
commitment on the part of C&T Solution Inc.
C&T Solution Inc. disclaims all warranties, express or implied, including, without limitation, those of
merchantability, fitness for a particular purpose with respect to contents of this User’s Manual. Users must
take full responsibility for the application of the product.
Copyright Notice
All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means,
electronic or mechanical, including photocopying, recording, or information storage and retrieval systems,
without the prior written permission of C&T Solutions Inc. Copyright © C&T Solutions Inc.
Trademarks Acknowledgment
Intel®, Celeron® and Pentium® are trademarks of Intel Corporation.
Windows® is registered trademark of Microsoft Corporation.
AMI is trademark of American Megatrend Inc.
IBM, XT, AT, PS/2 and Personal System/2 are trademarks of International Business Machines Corporation
All other products and trademarks mentioned in this manual are trademarks of their respective owners.
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. Please recycle to minimize pollution
and ensure environment protection.
Prefaces
Revision
Description
Date
1.0
Manual Released
2016/07/04
1.1
Model
Revised
2016/09/23
1.2
Switches and Connectors Revised
2017/10/26
1.3
Power Connector Definition
Revised
2017/11/02
Page 5
ACO-3000 l User’s Manual
5
Safety Precautions
Before installing and using the equipment, please read the following precautions:
Put this equipment on a reliable surface during installation. Dropping it or letting it fall could
cause damage.
The power outlet shall be installed near the equipment and shall be easily accessible.
Turn off the system power and disconnect the power cord from its source before making any
installation. Be sure both the system and the external devices are turned OFF. Sudden surge
of power could ruin sensitive components. Make sure the equipment is properly grounded.
When the power is connected, never open the equipment. The equipment should be opened
only by qualified service personnel.
Make sure the voltage of the power source is correct before connecting the equipment to the
power outlet.
Disconnect this equipment from the power before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.
Avoid the dusty, humidity and temperature extremes.
Do not place heavy objects on the equipment.
If the equipment is not used for long time, disconnect it from the power to avoid being
damaged by transient over-voltage.
The storage temperature shall be above -40°C and below 85°C.
The computer is provided with a battery-powered real-time clock circuit. There is a danger of
explosion if incorrectly replaced. Replace only with the same or equivalent type
recommended by the manufacturer.
If one of the following situation arises, get the equipment checked be service personnel:
• The power cord or plug is damaged.
• Liquid has penetrated into the equipment.
• The equipment has been exposed to moisture.
• The equipment does not work well or it cannot work according the user’s manual.
• The equipment has been dropped and damaged.
• The equipment has obvious signs of breakage.
Preface
Page 6
ACO-3000 l User’s Manual
6
Technical Support and Assistance
1. Visit the C&T Solution Inc website at www.candtsolution.com where you can find the latest
information about the product.
2. Contact your distributor, our technical support team or sales representative for technical support if
you need additional assistance. Please have following information ready before you call:
Model name and serial number
Description of your peripheral attachments
Description of your software (operating system, version, application software, etc.)
A complete description of the problem
The exact wording of any error messages
Conventions Used in this Manual
Preface
This indication alerts operators to an operation that, if not strictly observed,
may result in severe injury.
WARNING
This indication alerts operators to an operation that, if not strictly observed,
may result in safety hazards to personnel or damage to equipment.
CAUTION
This indication provides additional information to complete a task easily.
NOTE
Page 7
ACO-3000 l User’s Manual
7
Package Contents
Before installation, please ensure all the items listed in the following table are included in the package.
Item
Description
Q’ty
1
ACO
-3000 Series Vehicle Applied Fanless System 1
2
Utility DVD Driver
1
3
Wall Mount Kit
1
4
Accessory Kit
1
5
DVI to VGA Adapter
1
Preface
Ordering Information
Model No. Product Description
ACO-3000-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN
ACO-3000-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN
ACO-3000-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN
ACO-3000-4L-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 6x LAN
ACO-3000-4L-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 6x LAN
ACO-3000-4L-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 6x LAN
ACO-3000-4L-M12-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 4x M12 LAN
ACO-3000-4L-M12-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 4x M12 LAN
ACO-3000-4L-M12-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 4x M12 LAN
ACO-3000-4P-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 4x PoE
ACO-3000-4P-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 4x PoE
ACO-3000-4P-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 4x PoE
Page 8
ACO-3000 l User’s Manual
8
Model No. Product Description
ACO-3000-4P-M12-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 4x M12 PoE
ACO-3000-4P-M12-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 4x M12 PoE
ACO-3000-4P-M12-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 4x M12 PoE
ACO-3011E-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 1x PCIe x4 expansion
ACO-3011E-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 1x PCIe x4 expansion
ACO-3011E-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 1x PCIe x4 expansion
ACO-3011E-4L-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 6x LAN, 1x PCIe x4 expansion
ACO-3011E-4L-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 6x LAN, 1x PCIe x4 expansion
ACO-3011E-4L-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 6x LAN, 1x PCIe x4 expansion
ACO-3011E-4L-M12-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 4x M12 LAN, 1x PCIe x4 expansion
ACO-3011E-4L-M12-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 4x M12 LAN, 1x PCIe x4 expansion
ACO-3011E-4L-M12-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 4x M12 LAN, 1x PCIe x4 expansion
ACO-3011E-4P-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 4x PoE, 1x PCIe x4 expansion
ACO-3011E-4P-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 4x PoE, 1x PCIe x4 expansion
ACO-3011E-4P-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 4x PoE, 1x PCIe x4 expansion
ACO-3011E-4P-M12-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 4x M12 PoE, 1x PCIe x4 expansion
ACO-3011E-4P-M12-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 4x M12 PoE, 1x PCIe x4 expansion
ACO-3011E-4P-M12-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 4x M12 PoE, 1x PCIe x4 expansion
Page 9
ACO-3000 l User’s Manual
9
Model No. Product Description
ACO-3011P-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 1x PCI expansion
ACO-3011P-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 1x PCI expansion
ACO-3011P-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 1x PCI expansion
ACO-3011P-4L-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 6x LAN, 1x PCI expansion
ACO-3011P-4L-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 6x LAN, 1x PCI expansion
ACO-3011P-4L-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 6x LAN, 1x PCI expansion
ACO-3011P-4L-M12-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 4x M12 LAN, 1x PCI expansion
ACO-3011P-4L-M12-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 4x M12 LAN, 1x PCI expansion
ACO-3011P-4L-M12-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 4x M12 LAN, 1x PCI expansion
ACO-3011P-4P-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 4x PoE, 1x PCI expansion
ACO-3011P-4P-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 4x PoE, 1x PCI expansion
ACO-3011P-4P-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 4x PoE, 1x PCI expansion
ACO-3011P-4P-M12-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 4x M12 PoE, 1x PCI expansion
ACO-3011P-4P-M12-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 4x M12 PoE, 1x PCI expansion
ACO-3011P-4P-M12-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 4x M12 PoE, 1x PCI expansion
ACO-3022EE-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 2x PCIe x4 expansion
ACO-3022EE-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 2x PCIe x4 expansion
ACO-3022EE-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 2x PCIe x4 expansion
Page 10
ACO-3000 l User’s Manual
10
Model No. Product Description
ACO-3022EE-4L-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 6x LAN, 2x PCIe x4 expansion
ACO-3022EE-4L-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 6x LAN, 2x PCIe x4 expansion
ACO-3022EE-4L-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 6x LAN, 2x PCIe x4 expansion
ACO-3022EE-4L-M12-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 4x M12 LAN, 2x PCIe x4 expansion
ACO-3022EE-4L-M12-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 4x M12 LAN, 2x PCIe x4 expansion
ACO-3022EE-4L-M12-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 4x M12 LAN, 2x PCIe x4 expansion
ACO-3022EE-4P-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 4x PoE, 2x PCIe x4 expansion
ACO-3022EE-4P-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 4x PoE, 2x PCIe x4 expansion
ACO-3022EE-4P-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 4x PoE, 2x PCIe x4 expansion
ACO-3022EE-4P-M12-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 4x M12 PoE, 2x PCIe x4 expansion
ACO-3022EE-4P-M12-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 4x M12 PoE, 2x PCIe x4 expansion
ACO-3022EE-4P-M12-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 4x M12 PoE, 2x PCIe x4 expansion
ACO-3022PP-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 2x PCI expansion
ACO-3022PP-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 2x PCI expansion
ACO-3022PP-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 2x PCI expansion
ACO-3022PP-4L-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 6x LAN, 2x PCI expansion
ACO-3022PP-4L-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 6x LAN, 2x PCI expansion
ACO-3022PP-4L-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 6x LAN, 2x PCI expansion
Page 11
ACO-3000 l User’s Manual
11
Preface
Model No. Product Description
ACO-3022PP-4L-M12-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 4x M12 LAN, 2x PCI expansion
ACO-3022PP-4L-M12-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 4x M12 LAN, 2x PCI expansion
ACO-3022PP-4L-M12-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 4x M12 LAN, 2x PCI expansion
ACO-3022PP-4P-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 4x PoE, 2x PCI expansion
ACO-3022PP-4P-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 4x PoE, 2x PCI expansion
ACO-3022PP-4P-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 4x PoE, 2x PCI expansion
ACO-3022PP-4P-M12-5350U
Vehicle applied fanless embedded system with Intel® i5-5350U
processor, 2x LAN, 4x M12 PoE, 2x PCI expansion
ACO-3022PP-4P-M12-5010U
Vehicle applied fanless embedded system with Intel® i3-5010U
processor, 2x LAN, 4x M12 PoE, 2x PCI expansion
ACO-3022PP-4P-M12-3765U
Vehicle applied fanless embedded system with Intel® Celeron®
3765U processor, 2x LAN, 4x M12 PoE, 2x PCI expansion
Optional Accessories
Model No. Product Description
1
-E09A06002
Adapter AC/DC 12V 5A 60W with 3pin Terminal Block Plug 5.0mm Pitch,
GSM60A12
-CT
1
-E09A22101
Adapter AC/DC 24V 9.2A 220W with 3pin Terminal Block Plug 5.0mm Pitch,
GST220A24
-CT
SFICBL022
Power Cord, 3
-pin US Type, 180cm
1
-TPCD00002
Power Cord, European Type, 180cm
1
-TPCD00001
Power Cord, 3
-pin UK Type, 180cm
3
-DINR-0003
DIN
-Rail Mount Kit
Page 12
Chapter 1
Product Introductions
Page 13
ACO-3000 l User’s Manual
13
1.1.1 Key Features
Onboard Intel® Core ™ i5-5350U (2.9GHz) / Core™ i3-5010U (2.1GHz) / Celeron ® 3765U (1.9GHz) Dual
Core processor
1x DDR3L SO-DIMM Max. up to 8GB
Triple Independent Display from 1x DVI-I and 1x DisplayPort
2x Intel® GbE Port, Support Wake-on-LAN and PXE (ACO-3000, ACO-3011, ACO-3022 Series Only)
6x Intel® GbE Port, Support Wake-on-LAN and PXE (ACO-3000-4L, ACO-3000-4L-M12, ACO-3011-4L, ACO-
3011-4L-M12, ACO-3022-4L, ACO-3022-4L-M12 Series Only)
6x Intel® GbE Port with 4x PoE Function, Support Wake-on-LAN, 2x Support PXE (ACO-3000-4P, ACO-3000-
4P-M12, ACO-3011-4P, ACO-3011-4P-M12, ACO-3022-4P, ACO-3022-4P-M12 Series Only)
2x USB 3.0, 2x USB 2.0
4x RS232/422/485 Port
4x Isolated DI, 4x Isolated DO
1x Removable 2.5" SATA HDD Bay and 1x Internal 2.5” SATA SSD/HDD Bay
2x mSATA (Shared by 2x Mini-PCIe Socket) and 2x SIM Card Socket
9~48VDC Power Input, support AT/ATX Mode
2x Mini-PCIe Socket for Wi-Fi, GSM, or I/O Expansion
1x PCIe x4 Expansion (ACO-3011E Series Only)
1x PCI Expansion (ACO-3011P Series Only)
2x PCIe x4 Expansion (ACO-3022EE Series Only)
2x PCI Expansion (ACO-3022PP Series Only)
Power Ignition Sensing
Remote Power On/Off Switch
1.1 Overview
Based on 5thGen. Intel®Core™ i5-5350U (2.9GHz) / i3-5010U (2.1GHz) or Celeron®3765U (1.9GHz) Dual Core
processor, ACO-3000 series is an extreme features integration, outstanding system performance, versatile I/O
connections, and rugged reliability fanless embedded systems. Compliant with E-Mark and EMC Conformity with
EN50155 & EN50121-3-2 certification, as well as support up to 6x LAN or 4x PoE versions and power ignition
function, ACO-3000 series is dedicated to use for in-vehicle applications. It offers modularize expansion I/O, rich
connectivity interfaces, wide range (9~48V) DC power input, and high reliability even operating in temperature
extremes (-40°C~+70°C).
Featuring with completely cable-less designed, high functional, one-piece housing design, and anti-vibration,
ACO-3000 series are ruggedized systems that can operate in harsh environments and easy to install and maintain.
A build in over voltage protection (OVP), over current protection (OCP), reverse protection, and wide range DC
power input makes ACO-3000 series are safety system for all industrial applications.
Chapter 1: Product Introductions
ACO-3000 Series
ACO-3022 SeriesACO-3011 Series
Page 14
ACO-3000 l User’s Manual
14
1.2 Hardware Specification
Chapter 1: Product Introductions
Processor System
• Onboard Intel® Core ™ i5-5350U / Core™ i3-5010U /
Celeron ® 3765U Dual Core Processor, 2.9 / 2.1 / 1.9GHz
with AMI 64Mbit SPI BIOS
Memory
• 1x 204-Pin DDR3L-1066 / 1333MHz SO-DIMM
(un-buffered and non-ECC), Max. up to 8GB
Display
Triple Display
• 1x DVI -D, 1x VGA, and 1x DisplayPort
Expansion
• ACO-3011E Series: 1x PCIe x4
• ACO-3011P Series: 1x PCI
• ACO-3022EE Series : 2x PCIe x4
• ACO-3022PP Series: 2x PCI
• 2x Full-size Mini PCIe Socket for Wi-Fi / GSM / Expansion
Module
• 1x Universal I/O Bracket (ACO-3000, ACO-3011E-4L/4P, ACO-
3011E-4L/4P-M12, ACO-3011P-4L/4P, ACO-3011E-4L/4P-M12, ACO3022EE-4L/4P, ACO-3022EE-4L/4P-M12, ACO-3022PP-4L/4P, ACO3022PP-4L/4P-M12 Only)
• 2x Universal I/O Bracket (ACO-3011E/P, ACO-3022EE/PP, Only)
Ethernet
• 2x Intel® i210-AT GbE LAN Port, Support Wake-on-LAN
and PXE (ACO-3000, ACO-3011E/P,ACO-3022E/P Only)
• 6x Intel® i210-AT GbE LAN Port, LAN1 and LAN2 Support
Wake-on-LAN (ACO-3000-4L, ACO-3000-4L-M12, ACO-3011E/P-4L,
ACO-3011E/P-4L-M12, ACO-3022EE/PP-4L, ACO-3022EE/PP-4L-M12
Only)
• 4x 802.3at Compliant PoE Port, The Maximum DC Power
Delivery on Each PoE is 25.5W (ACO-3000-4P, ACO-3000-4P-
M12, ACO-3011E/P-4P, ACO-3011E/P-4P-M12, ACO-3022EE/PP-4P,
ACO-3022EE/PP-4P-M12 Only)
Audio
• Codec: Realtek ALC888S
• 1x Mic-in and 1x Speak-out
Watchdog Timer
• Software Programmable Supports 1~255 sec. System
Reset
Storage
• 1x Removable 2.5" SATA HDD Bay
• 1x Internal 2.5" SATA HDD Bay
• 2x mSATA Socket (Shared by 2x Mini-PCIe Socket)
• 2x External SIM Card Socket
• Support RAID 0, 1, 5, 10
I/O Ports
• 2x USB 3.0 Port
• 2x USB 2.0 Port
• 4 Isolated DI and 4 Isolated DO Port
• 4x DB9 Flow Control for COM1~4, Support
RS232/422/485 with Auto Flow Control
• 3x Antenna Hole
• 1x Power Switch
• 1x AT/ATX Switch
• 1x Remote Power on/off Connector
Digital Input & Output
• 4x Digital Input (Source Type)
- Input Voltage (Dry Contact):
Logic 0: Close to GND
Logic 1: Open
- Input Voltage:
Logic 0: 3V max.
Logic 1: 5V min. (DI to COM-)
• 4x Digital Output
- Supply Voltage: 5~30VDC
- Sink Current: 200 mA Max. Per Channel
Power
• Support AT, ATX Mode
• 1x 3-pin Terminal Block Connector with Power Input
9~48VDC
• Power Ignition Sensing
• 1x Optional AC/DC 12V/5A, 60W Power Adapter
• 1x Optional AC/DC 24V/9.2A, 220W Power Adapter
(ACO-3000-4P, ACO-3000-4P-M12, ACO-3011-4P, ACO3011-4P-M12, ACO-3022-4P, ACO-3022-4P-M12 Series
Only)
Environment
• Operating Temperature: Ambient with Air Flow:
-40°C to 70°C (with Industrial Grade Peripherals)
• Storage Temperature: -40°C to 85°C
• Relative humidity: 10%~95% (non-condensing)
Physical
• ACO-3000 Series
Dimension (WxDxH, mm): 185 x 197 x 57.4 mm
Weight: 2.16 kg ~ 2.54 kg
• ACO-3011 Series
Dimension (WxDxH, mm): 185 x 197 x 85 mm
Weight: TBD
• ACO-3022 Series
Dimension (WxDxH, mm): 185 x 197 x 105 mm
Weight: TBD
• Construction: Extruded Aluminum with Heavy Duty
Metal
• Mounting: Wall/ DIN-Rail Mounting
Operating System
• Windows® 7
• WES7
• Windows® 8.1
• WES8.1
• Windows 10
• Linux kernel 3.X
Certifications
• CE
• FCC Class A
• E-Mark
• EMC Conformity with EN50155 & EN50121-3-2
Page 15
ACO-3000 l User’s Manual
15
1.3 System I/O
1.3.1 ACO-3000
Chapter 1: Product Introductions
Front Panel
ATX power on/off switch
Press to power-on or power-off the system
Reset switch
Press to reset the system
AT/ATX mode select switch
Used to select AT or ATX power mode
12V/24V power input select switch
Used to car mode select 12V or 24V power input
PC/Car mode select switch
Used to select PC or Car mode
Delay time select switch
Used to select car mode PC turn off delay time
SIM card
Used to insert SIM card
COM port
COM1 ~ COM2 support RS232/422/485 serial
device
Universal I/O Bracket
Used to customized I/O output
HDD port
Removable 2.5" SATA HDD Area
Power LED
Indicates the power status of the system
HDD LED
Indicates the status of the hard drive
Temperature LED
Indicates the temperature status of the system
Watchdog LED
Indicates the status of the watchdog active
GPIO LED
Indicates the status of the customer define
Ethernet LEDs
Indicates the status of the LAN active
Page 16
ACO-3000 l User’s Manual
16
Chapter 1: Product Introductions
Rear Panel
DC IN
Used to plug a DC power input with terminal
block
DVI-I port
Used to connect a DVI monitor or connect
optional split cable for dual display mode
DisplayPort
Used to connect a DisplayPort monitor
USB 3.0 port
Used to connect USB 3.0/2.0/1.1 device
USB 2.0 port
Used to connect USB 2.0/1.1 device
LAN port
Used to connect the system to a local area
network
COM port
COM3 ~ COM4 support RS232/422/485 serial
device
Mic-in
Used to connect a microphone
Speaker-out
Used to connect a speaker
Digital I/O Terminal Block
The Digital I/O terminal block supports 4 digital
input and 4 digital output
Remote Power on/off Terminal Block
Used to plug a remote power on/off terminal
block
Antenna hole
Used to connect an antenna for optional MiniPCIe WiFi module
Page 17
ACO-3000 l User’s Manual
17
1.3.2 ACO-3000-4L(P)
Chapter 1: Product Introductions
Front Panel
ATX power on/off switch
Press to power-on or power-off the system
Reset switch
Press to reset the system
AT/ATX mode select switch
Used to select AT or ATX power mode
12V/24V power input select switch
Used to car mode select 12V or 24V power input
PC/Car mode select switch
Used to select PC or Car mode
Delay time select switch
Used to select car mode PC turn off delay time
SIM card
Used to insert SIM card
COM port
COM1 ~ COM2 support RS232/422/485 serial
device
LAN Port
Used to connect the system to a local area
network (ACO-3000-4L Only)
PoE Port
Used to connect the system to a local area
network with power over Ethernet (ACO-3000-4P
Only)
HDD port
Removable 2.5" SATA HDD Area
Power LED
Indicates the power status of the system
HDD LED
Indicates the status of the hard drive
Temperature LED
Indicates the temperature status of the system
Watchdog LED
Indicates the status of the watchdog active
GPIO LED
Indicates the status of the customer define
Ethernet LEDs
Indicates the status of the LAN active
Page 18
ACO-3000 l User’s Manual
18
Chapter 1: Product Introductions
Rear Panel
DC IN
Used to plug a DC power input with terminal
block
DVI-I port
Used to connect a DVI monitor or connect
optional split cable for dual display mode
DisplayPort
Used to connect a DisplayPort monitor
USB 3.0 port
Used to connect USB 3.0/2.0/1.1 device
USB 2.0 port
Used to connect USB 2.0/1.1 device
LAN port
Used to connect the system to a local area
network
COM port
COM3 ~ COM4 support RS232/422/485 serial
device
Mic-in
Used to connect a microphone
Speaker-out
Used to connect a speaker
Digital I/O Terminal Block
The Digital I/O terminal block supports 4 digital
input and 4 digital output
Remote Power on/off Terminal Block
Used to plug a remote power on/off terminal
block
Antenna hole
Used to connect an antenna for optional MiniPCIe WiFi module
Page 19
ACO-3000 l User’s Manual
19
1.3.3 ACO-3000-4L(P)-M12
Chapter 1: Product Introductions
Front Panel
ATX power on/off switch
Press to power-on or power-off the system
Reset switch
Press to reset the system
AT/ATX mode select switch
Used to select AT or ATX power mode
12V/24V power input select switch
Used to car mode select 12V or 24V power input
PC/Car mode select switch
Used to select PC or Car mode
Delay time select switch
Used to select car mode PC turn off delay time
SIM card
Used to insert SIM card
COM port
COM1 ~ COM2 support RS232/422/485 serial
device
M12 LAN Port
Used to connect the system to a local area
network (ACO-3000-4L-M12 Only)
M12 PoE Port
Used to connect the system to a local area
network with power over Ethernet (ACO-30004P-M12 Only)
HDD port
Removable 2.5" SATA HDD Area
Power LED
Indicates the power status of the system
HDD LED
Indicates the status of the hard drive
Temperature LED
Indicates the temperature status of the system
Watchdog LED
Indicates the status of the watchdog active
GPIO LED
Indicates the status of the customer define
Ethernet LEDs
Indicates the status of the LAN active
Page 20
ACO-3000 l User’s Manual
20
Chapter 1: Product Introductions
Rear Panel
DC IN
Used to plug a DC power input with terminal
block
DVI-I port
Used to connect a DVI monitor or connect
optional split cable for dual display mode
DisplayPort
Used to connect a DisplayPort monitor
USB 3.0 port
Used to connect USB 3.0/2.0/1.1 device
USB 2.0 port
Used to connect USB 2.0/1.1 device
LAN port
Used to connect the system to a local area
network
COM port
COM3 ~ COM4 support RS232/422/485 serial
device
Mic-in
Used to connect a microphone
Speaker-out
Used to connect a speaker
Digital I/O Terminal Block
The Digital I/O terminal block supports 4 digital
input and 4 digital output
Remote Power on/off Terminal Block
Used to plug a remote power on/off terminal
block
Antenna hole
Used to connect an antenna for optional MiniPCIe WiFi module
Page 21
ACO-3000 l User’s Manual
21
1.3.4 ACO-3011E(P)
Chapter 1: Product Introductions
Front Panel
ATX power on/off switch
Press to power-on or power-off the system
Reset switch
Press to reset the system
AT/ATX mode select switch
Used to select AT or ATX power mode
12V/24V power input select switch
Used to car mode select 12V or 24V power input
PC/Car mode select switch
Used to select PC or Car mode
Delay time select switch
Used to select car mode PC turn off delay time
SIM card
Used to insert SIM card
COM port
COM1 ~ COM2 support RS232/422/485 serial
device
Universal I/O Bracket
Used to customized I/O output
HDD port
Removable 2.5" SATA HDD Area
Power LED
Indicates the power status of the system
HDD LED
Indicates the status of the hard drive
Temperature LED
Indicates the temperature status of the system
Watchdog LED
Indicates the status of the watchdog active
GPIO LED
Indicates the status of the customer define
Ethernet LEDs
Indicates the status of the LAN active
Page 22
ACO-3000 l User’s Manual
22
Chapter 1: Product Introductions
Rear Panel
DC IN
Used to plug a DC power input with terminal
block
DVI-I port
Used to connect a DVI monitor or connect
optional split cable for dual display mode
DisplayPort
Used to connect a DisplayPort monitor
USB 3.0 port
Used to connect USB 3.0/2.0/1.1 device
USB 2.0 port
Used to connect USB 2.0/1.1 device
LAN port
Used to connect the system to a local area
network
COM port
COM3 ~ COM4 support RS232/422/485 serial
device
Mic-in
Used to connect a microphone
Speaker-out
Used to connect a speaker
Digital I/O Terminal Block
The Digital I/O terminal block supports 4 digital
input and 4 digital output
Remote Power on/off Terminal Block
Used to plug a remote power on/off terminal
block
Expansion Area
Used to plug PCIe Card (ACO-3011E Only)
Used to plug PCI Card (ACO-3011P Only)
Antenna hole
Used to connect an antenna for optional MiniPCIe WiFi module
Page 23
ACO-3000 l User’s Manual
23
1.3.5 ACO-3011E-4L(P) / ACO-3011P-4L(P)
Chapter 1: Product Introductions
Front Panel
ATX power on/off switch
Press to power-on or power-off the system
Reset switch
Press to reset the system
AT/ATX mode select switch
Used to select AT or ATX power mode
12V/24V power input select switch
Used to car mode select 12V or 24V power input
PC/Car mode select switch
Used to select PC or Car mode
Delay time select switch
Used to select car mode PC turn off delay time
SIM card
Used to insert SIM card
COM port
COM1 ~ COM2 support RS232/422/485 serial
device
LAN Port
Used to connect the system to a local area
network (ACO-3011-4L Only)
PoE Port
Used to connect the system to a local area
network with power over Ethernet (ACO-3011-4P
Only)
Universal I/O Bracket
Used to customized I/O output
HDD port
Removable 2.5" SATA HDD Area
Power LED
Indicates the power status of the system
HDD LED
Indicates the status of the hard drive
Temperature LED
Indicates the temperature status of the system
Watchdog LED
Indicates the status of the watchdog active
GPIO LED
Indicates the status of the customer define
Ethernet LEDs
Indicates the status of the LAN active
Page 24
ACO-3000 l User’s Manual
24
Chapter 1: Product Introductions
Rear Panel
DC IN
Used to plug a DC power input with terminal
block
DVI-I port
Used to connect a DVI monitor or connect
optional split cable for dual display mode
DisplayPort
Used to connect a DisplayPort monitor
USB 3.0 port
Used to connect USB 3.0/2.0/1.1 device
USB 2.0 port
Used to connect USB 2.0/1.1 device
LAN port
Used to connect the system to a local area
network
COM port
COM3 ~ COM4 support RS232/422/485 serial
device
Mic-in
Used to connect a microphone
Speaker-out
Used to connect a speaker
Digital I/O Terminal Block
The Digital I/O terminal block supports 4 digital
input and 4 digital output
Remote Power on/off Terminal Block
Used to plug a remote power on/off terminal
block
Expansion Area
Used to plug PCIe Card (ACO-3011E-4L/4P Only)
Used to plug PCI Card (ACO-3011P-4L/4P Only)
Antenna hole
Used to connect an antenna for optional MiniPCIe WiFi module
Page 25
ACO-3000 l User’s Manual
25
1.3.6 ACO-3011E-4L(P)-M12 / ACO-3011P-4L(P)-M12
Chapter 1: Product Introductions
Front Panel
ATX power on/off switch
Press to power-on or power-off the system
Reset switch
Press to reset the system
AT/ATX mode select switch
Used to select AT or ATX power mode
12V/24V power input select switch
Used to car mode select 12V or 24V power input
PC/Car mode select switch
Used to select PC or Car mode
Delay time select switch
Used to select car mode PC turn off delay time
SIM card
Used to insert SIM card
COM port
COM1 ~ COM2 support RS232/422/485 serial
device
M12 LAN Port
Used to connect the system to a local area
network (ACO-3010-4L-M12 Only)
M12 PoE Port
Used to connect the system to a local area
network with power over Ethernet (ACO-30104P-M12 Only)
Universal I/O Bracket
Used to customized I/O output
HDD port
Removable 2.5" SATA HDD Area
Power LED
Indicates the power status of the system
HDD LED
Indicates the status of the hard drive
Temperature LED
Indicates the temperature status of the system
Watchdog LED
Indicates the status of the watchdog active
GPIO LED
Indicates the status of the customer define
Ethernet LEDs
Indicates the status of the LAN active
Page 26
ACO-3000 l User’s Manual
26
Chapter 1: Product Introductions
Rear Panel
DC IN
Used to plug a DC power input with terminal
block
DVI-I port
Used to connect a DVI monitor or connect
optional split cable for dual display mode
DisplayPort
Used to connect a DisplayPort monitor
USB 3.0 port
Used to connect USB 3.0/2.0/1.1 device
USB 2.0 port
Used to connect USB 2.0/1.1 device
LAN port
Used to connect the system to a local area
network
COM port
COM3 ~ COM4 support RS232/422/485 serial
device
Mic-in
Used to connect a microphone
Speaker-out
Used to connect a speaker
Digital I/O Terminal Block
The Digital I/O terminal block supports 4 digital
input and 4 digital output
Expansion Area
Used to plug PCIe Card (ACO-3011E-4L/4P-M12
Only)
Used to plug PCI Card (ACO-3011P-4L/4P-M12
Only)
Antenna hole
Used to connect an antenna for optional MiniPCIe WiFi module
Page 27
ACO-3000 l User’s Manual
27
Chapter 1: Product Introductions
27
1.3.7 ACO-3022EE(PP)
Front Panel
ATX power on/off switch
Press to power-on or power-off the system
Reset switch
Press to reset the system
AT/ATX mode select switch
Used to select AT or ATX power mode
12V/24V power input select switch
Used to car mode select 12V or 24V power input
PC/Car mode select switch
Used to select PC or Car mode
Delay time select switch
Used to select car mode PC turn off delay time
SIM card
Used to insert SIM card
COM port
COM1 ~ COM2 support RS232/422/485 serial
device
Universal I/O Bracket
Used to customized I/O output
HDD port
Removable 2.5" SATA HDD Area
Power LED
Indicates the power status of the system
HDD LED
Indicates the status of the hard drive
Temperature LED
Indicates the temperature status of the system
Watchdog LED
Indicates the status of the watchdog active
GPIO LED
Indicates the status of the customer define
Ethernet LEDs
Indicates the status of the LAN active
Page 28
ACO-3000 l User’s Manual
28
Chapter 1: Product Introductions
28
Rear Panel
DC IN
Used to plug a DC power input with terminal
block
DVI-I port
Used to connect a DVI monitor or connect
optional split cable for dual display mode
DisplayPort
Used to connect a DisplayPort monitor
USB 3.0 port
Used to connect USB 3.0/2.0/1.1 device
USB 2.0 port
Used to connect USB 2.0/1.1 device
LAN port
Used to connect the system to a local area
network
COM port
COM3 ~ COM4 support RS232/422/485 serial
device
Mic-in
Used to connect a microphone
Speaker-out
Used to connect a speaker
Digital I/O Terminal Block
The Digital I/O terminal block supports 4 digital
input and 4 digital output
Remote Power on/off Terminal Block
Used to plug a remote power on/off terminal
block
Expansion Area
Used to plug PCIe Card (ACO-3022EE Only)
Used to plug PCI Card (ACO-3022PP Only)
Antenna hole
Used to connect an antenna for optional MiniPCIe WiFi module
Page 29
ACO-3000 l User’s Manual
29
Chapter 1: Product Introductions
29
1.3.8 ACO-3022EE-4L(P) / ACO-3022PP-4L(P)
Front Panel
ATX power on/off switch
Press to power-on or power-off the system
Reset switch
Press to reset the system
AT/ATX mode select switch
Used to select AT or ATX power mode
12V/24V power input select switch
Used to car mode select 12V or 24V power input
PC/Car mode select switch
Used to select PC or Car mode
Delay time select switch
Used to select car mode PC turn off delay time
SIM card
Used to insert SIM card
COM port
COM1 ~ COM2 support RS232/422/485 serial
device
LAN Port
Used to connect the system to a local area
network (ACO-302EE-4L, ACO-3022PP-4L Only)
PoE Port
Used to connect the system to a local area
network with power over Ethernet (ACO-3022EE4P, ACO-3022PP-4P Only)
Universal I/O Bracket
Used to customized I/O output
HDD port
Removable 2.5" SATA HDD Area
Power LED
Indicates the power status of the system
HDD LED
Indicates the status of the hard drive
Temperature LED
Indicates the temperature status of the system
Watchdog LED
Indicates the status of the watchdog active
GPIO LED
Indicates the status of the customer define
Ethernet LEDs
Indicates the status of the LAN active
Page 30
ACO-3000 l User’s Manual
30
Chapter 1: Product Introductions
30
Rear Panel
DC IN
Used to plug a DC power input with terminal
block
DVI-I port
Used to connect a DVI monitor or connect
optional split cable for dual display mode
DisplayPort
Used to connect a DisplayPort monitor
USB 3.0 port
Used to connect USB 3.0/2.0/1.1 device
USB 2.0 port
Used to connect USB 2.0/1.1 device
LAN port
Used to connect the system to a local area
network
COM port
COM3 ~ COM4 support RS232/422/485 serial
device
Mic-in
Used to connect a microphone
Speaker-out
Used to connect a speaker
Digital I/O Terminal Block
The Digital I/O terminal block supports 4 digital
input and 4 digital output
Remote Power on/off Terminal Block
Used to plug a remote power on/off terminal
block
Expansion Area
Used to plug PCIe Card (ACO-3022EE-4L/4P Only)
Used to plug PCI Card (ACO-3022PP-4L/4P Only)
Antenna hole
Used to connect an antenna for optional MiniPCIe WiFi module
Page 31
ACO-3000 l User’s Manual
31
Chapter 1: Product Introductions
3131
1.3.9 ACO-3022EE-4L(P)-M12 / ACO-3022PP-4L(P)-M12
Front Panel
ATX power on/off switch
Press to power-on or power-off the system
Reset switch
Press to reset the system
AT/ATX mode select switch
Used to select AT or ATX power mode
12V/24V power input select switch
Used to car mode select 12V or 24V power input
PC/Car mode select switch
Used to select PC or Car mode
Delay time select switch
Used to select car mode PC turn off delay time
SIM card
Used to insert SIM card
COM port
COM1 ~ COM2 support RS232/422/485 serial
device
M12 LAN Port
Used to connect the system to a local area
network (ACO-302EE-4L-M12, ACO-3022PP-4LM12 Only)
M12 PoE Port
Used to connect the system to a local area
network with power over Ethernet (ACO-3022EE4P-M12, ACO-3022PP-4P-M12 Only)
Universal I/O Bracket
Used to customized I/O output
HDD port
Removable 2.5" SATA HDD Area
Power LED
Indicates the power status of the system
HDD LED
Indicates the status of the hard drive
Temperature LED
Indicates the temperature status of the system
Watchdog LED
Indicates the status of the watchdog active
GPIO LED
Indicates the status of the customer define
Ethernet LEDs
Indicates the status of the LAN active
Page 32
ACO-3000 l User’s Manual
32
Chapter 1: Product Introductions
3232
Rear Panel
DC IN
Used to plug a DC power input with terminal
block
DVI-I port
Used to connect a DVI monitor or connect
optional split cable for dual display mode
DisplayPort
Used to connect a DisplayPort monitor
USB 3.0 port
Used to connect USB 3.0/2.0/1.1 device
USB 2.0 port
Used to connect USB 2.0/1.1 device
LAN port
Used to connect the system to a local area
network
COM port
COM3 ~ COM4 support RS232/422/485 serial
device
Mic-in
Used to connect a microphone
Speaker-out
Used to connect a speaker
Digital I/O Terminal Block
The Digital I/O terminal block supports 4 digital
input and 4 digital output
Remote Power on/off Terminal Block
Used to plug a remote power on/off terminal
block
Expansion Area
Used to plug PCIe Card (ACO-3022EE-4L/4P-M12
Only)
Used to plug PCI Card (ACO-3022PP-4L/4P-M12
Only)
Antenna hole
Used to connect an antenna for optional MiniPCIe WiFi module
Page 33
ACO-3000 l User’s Manual
33
1.4 Mechanical Dimensions
1.4.1 ACO-3000 / ACO-3000-4L(P) / ACO-3000-4L(P)-M12
Unit: mm
Chapter 1: Product Introductions
Page 34
ACO-3000 l User’s Manual
34
1.4.2 ACO-3011E(P) / ACO-3011E(P)-4L(P) / ACO-3011E(P)-4L(P)-M12
Unit: mm
Chapter 1: Product Introductions
Page 35
ACO-3000 l User’s Manual
35
1.4.3 ACO-3022EE(PP) / ACO-3022EE(PP)-4L(P) / ACO-3022EE(PP)-4L(P)-M12
Unit: mm
Chapter 1: Product Introductions
Page 36
Chapter 2
Switches and Connectors
Page 37
ACO-3000 l User’s Manual
37
2.1 Switch and Connector Locations
2.1.1 Top View
Chapter 2: Switches and Connectors
Page 38
ACO-3000 l User’s Manual
38
2.1.2 Bottom View
Chapter 2: Switches and Connectors
Page 39
ACO-3000 l User’s Manual
39
2.2 Connector / Switch Definition
List of Connector / Switch
Chapter 2: Switches and Connectors
Connector Location Definition
AT_ATX
1
AT
/ ATX Power Mode Switch
CLR_CMOS
1
Clear
BIOS Switch
CAR_PWR
1
Car / PC
Function Switch
12
V_24V_SEL1
12V / 24V Car Battery Switch
DELAY_TIME
1
Car
mode PC turn off delay time
PWR_SW
1
Power
Switch
RESET
1
Reset
Switch
USB
1_2_1
USB 3.0 Port
USB
3_4_1
USB 2.0 Port
SIM
1, SIM2
SIM
Card Socket
COM1_1
, COM2_1, COM3_1, COM4_1
RS232
/ RS422 / RS485 Connector
LAN
1_1, LAN2_1
LAN Port
LAN
3, LAN4, LAN5, LAN6
LAN Port / M12 LAN Port
DC_IN
1
3
-pin DC 9~48V Power Input Connector
DVI_I
1
DVI
-I Connector
DP1
DisplayPort
Connector
SPK_OUT
1
Speaker
-out Jack
MIC_IN
1
Mic
-in Jack
DIO1
4DI
/ 4DO Connector
PWR_SW
2
Remote
Power Switch
LAN_M
2
LAN Module
Connector
PWRIO_M
1
Power Module
Connector
CN
1, CN2
Mini PCI
-Express / mSATA Socket
SATA
1, SATA2
SATA
with Power Connector
POWER1, POWER2
Power Connector
PCIE1
PCI
-Express X4 Slot
PWR_LED
1
Power LED Status
HDD_LED
1
HDD Access LED Status
TEMP_LED
1
Temperature LED Status
WDT_LED
1
Watchdog LED Status
GPIO_LED
1
GPIO LED Status
LAN
1_LINK1, LAN2_LINK1
LAN
Link LED
LAN
1_ACT1, LAN2_ACT1
LAN
Active LED
Page 40
ACO-3000 l User’s Manual
Switch Definition
1-2 (Left)
AT Power Mode
2-3 (Right)
ATX Power Mode
（Default）
40
2.3 Switches Definitions
AT_ATX1: AT / ATX Power Mode Switch
CLR_CMOS1: Clear BIOS Switch
Switch Definition
Off Normal Status (Default)
ON Clear BIOS
Chapter 2: Switches and Connectors
Switch Definition
1-2 (Left)
PC
Power Mode
2-3 (Right)
Power Ignition Mode
（Default）
CAR_PWR1: PC / Power Ignition Mode Switch
Switch Definition
1-2 (Left)
Battery 24V
Input Mode（Default）
2-3 (Right)
Battery 12V
Input Mode
12V_24V_SEL1: 12V / 24V Input Mode Switch
Switch 1 / 2 / 3 Definition
OFF / OFF / OFF
0 sec.
（Default）
ON / ON / OFF
1 min.
ON / OFF / ON
5 min.
ON / OFF / OFF
10 min.
OFF / ON / ON
30 min.
OFF / ON / OFF
1 hour
OFF / OFF / ON
2 hour
DELAY_TIME1: Power off delay time setup Switch
Page 41
ACO-3000 l User’s Manual
Chapter 2: Switches and Connectors
Step of Setting Power Ignition
Step 1:
To select power ignition by PC/CAR switch.
Step 2:
To select battery input voltage by 12V / 24V switch.
Step 3:
To configure the power off delay time, please check the Delay Time Setting Options in
advance.
Step 4:
To connect the power and ignition power
Example: Delay Time Setting for 5 minutes
1. If delay time set as “5 minutes”
2. The system will shut down 5 minutes
later after turning off the vehicle.
Step 1
Pin 1-2 (Left): PC Power Mode
Pin 2-3 (Right): Power Ignition Mode
Step 2
Pin 1-2 (Left): Battery 24V Input Mode
Pin 2-3 (Right): Battery 12V Input Mode
Switch 1 / 2 / 3 Power off delay time
ON / ON / ON
0 second
ON / ON / OFF
1 minute
ON / OFF / ON
5 minutes
ON / OFF / OFF
10 minutes
OFF / ON / ON
30 minutes
OFF / ON / OFF
1 hour
OFF / OFF / ON
2 hours
Step 3
Step 4
To connect the battery power and
ignition power
Page 42
ACO-3000 l User’s Manual
42
2.4 Connectors Definitions
Chapter 2: Switches and Connectors
42
PWR_SW1: Power Button
Pin Definition Pin Definition
1 NC 4 GND
2
Power Button
5 NC
3 NC 6 GND
Chapter 2: Switches and Connectors
RESET1 : Reset Button
Pin Definition
1 RESET
2 GND
USB1_2_1: USB3.0 Connector, Type A
Pin Definition Pin Definition
1 +5V 10 +5V
2 USB2_D0- 11 USB2_D1-
3 USB2_D0+ 12 USB2_D1+
4 GND 13 GND
5 USB3_RX1- 14 USB3_RX2-
6 USB3_RX1+ 15 USB3_RX2+
7 GND 16 GND
8 USB3_TX1- 17 USB3_TX2-
9 USB3_TX1+ 18 USB3_TX2+
USB3_4_1: USB2.0 Connector, Type A
Pin
USB3_4_1 Definition
1 +5V
2 USB2_D2-
3 USB2_D2+
4 GND
5 +5V
6 USB2_D3-
7 USB2_D3+
8 GND
Page 43
ACO-3000 l User’s Manual
43
Chapter 2: Switches and Connectors
43
SIM1, SIM2：SIM Card Socket
Pin Definition Pin Definition
C1 UIM_PWR C6 UIM_VPP
C2 UIM_RESET C7 UIM_DATA
C3 UIM_CLK CD NC
C5 GND COM GND
COM1_1: RS232 / RS422 / RS485 Connector
Connector Type: 9-pin D-Sub
Pin RS232 Definition
RS422 / 485 Full
Duplex Definition
RS485 Half Duplex
Definition
1 DCD1 TX1- DATA1-
2 RxD1 TX1+ DATA1+
3 TxD1 RX1+
4 DTR1 RX1-
5 GND
6 DSR1
7 RTS1
8 CTS1
9 RI1
COM2_1: RS232 / RS422 / RS485 Connector
Connector Type: 9-pin D-Sub
Pin RS232 Definition
RS422 / 485 Full
Duplex Definition
RS485 Half Duplex
Definition
1 DCD2 TX2- DATA2-
2 RxD2 TX2+ DATA2+
3 TxD2 RX2+
4 DTR2 RX2-
5 GND
6 DSR2
7 RTS2
8 CTS2
9 RI2
Page 44
ACO-3000 l User’s Manual
44
Chapter 2: Switches and Connectors
44
COM3_1: : RS232 / RS422 / RS485 Connector
Connector Type: 9-pin D-Sub
Pin RS232 Definition
RS422 / 485 Full
Duplex Definition
RS485 Half Duplex
Definition
1 DCD3 TX3- DATA3-
2 RxD3 TX3+ DATA3+
3 TxD3 RX3+
4 DTR3 RX3-
5 GND
6 DSR3
7 RTS3
8 CTS3
9 RI3
COM4_1: RS232 / RS422 / RS485 Connector
Connector Type: 9-pin D-Sub
Pin RS232 Definition
RS422 / 485 Full
Duplex Definition
RS485 Half Duplex
Definition
1 DCD4 TX4- DATA4-
2 RxD4 TX4+ DATA4+
3 TxD4 RX4+
4 DTR4 RX4-
5 GND
6 DSR4
7 RTS4
8 CTS4
9 RI4
Page 45
ACO-3000 l User’s Manual
45
Chapter 2: Switches and Connectors
45
LAN1, LAN2: RJ45 with LEDs Port
Connector Type: RJ45 Connector
Pin Definition Pin Definition
1 LAN1_MDI0P 5 LAN1_MDI2N
2 LAN1_MDI0N 6 LAN1_MDI1N
3 LAN1_MDI1P 7 LAN1_MDI3P
4 LAN1_MDI2P 8 LAN1_MDI3N
Pin Definition Pin Definition
1 LAN2_MDI0P 5 LAN2_MDI2N
2 LAN2_MDI0N 6 LAN2_MDI1N
3 LAN2_MDI1P 7 LAN2_MDI3P
4 LAN2_MDI2P 8 LAN2_MDI3N
Link LED Status Definition Act LED Status Definition
Steady Orange 1Gbps Network Link Blinking Yellow Data Activity
Steady Green 100Mbps Network Link Off No Activity
Off 10Mbps Network Link
LAN3, LAN4, LAN5, LAN6: RJ45 with LEDs Port
Connector Type: RJ45 Connector
Pin
LAN3~LAN6
Definition
Pin
LAN3~LAN6
Definition
1 LAN_MDI0P 5 LAN_MDI2N
2 LAN_MDI0N 6 LAN_MDI1N
3 LAN_MDI1P 7 LAN_MDI3P
4 LAN_MDI2P 8 LAN_MDI3N
Link LED Status LAN3~LAN6 Definition Act LED Status LAN3~LAN6 Definition
Steady Orange 1Gbps Network Link Blinking Yellow Data Activity
Steady Green 100Mbps Network Link Off No Activity
Off 10Mbps Network Link
Page 46
ACO-3000 l User’s Manual
46
Chapter 2: Switches and Connectors
46
DC_IN1: DC Power Input Connector (+9~48V)
Connector Type: Terminal Block 1X3 3-pin, 5.0mm pitch
Pin Definition
1 +9~48VIN
2 Power Ignition
3 GND
LAN3, LAN4, LAN5, LAN6: M12 Lan Port
Connector Type: M12 X-code Female Connector
Pin
LAN3~LAN6
Definition
Pin
LAN3~LAN6
Definition
1 LAN_MDI0P 5 LAN_MDI3N
2 LAN_MDI0N 6 LAN_MDI3N
3 LAN_MDI1P 7 LAN_MDI2P
4 LAN_MDI1N 8 LAN_MDI2N
DVI_I1: DVI-I Connector
Pin Definition Pin Definition
1 DVI_TX2- 16 DVI Hot Plug Detect
2 DVI_TX2+ 17 DVI_TX0-
3 GND 18 DVI_TX0+
4 NC 19 GND
5 NC 20 VGA_DDC_CLOCK
6 DVI_DDC_CLOCK 21 VGA_DDC_DATA
7 DVI_DDC_DATA 22 GND
8 VGA VSYNC 23 DVI_TXCLK+
9 DVI_TX1- 24 DVI_TXCLK-
10 DVI_TX1+ C1 VGA_RED
11 GND C2 VGA_GREEN
12 NC C3 VGA_BLUE
13 NC C4 VGA_HSYNC
14 +5V C5 GND
15 GND
Page 47
ACO-3000 l User’s Manual
47
Chapter 2: Switches and Connectors
DP1: DisplayPort Connector
Pin Definition Pin Definition
1 DP_LANE0_P 11 GND
2 GND 12 DP_LANE3_N
3 DP_LANE0_N 13 GND
4 DP_LANE1_P 14 GND
5 GND 15 DP_AUX_P
6 DP_LANE1_N 16 GND
7 DP_LANE2_P 17 DP_AUX_N
8 GND 18 DP_HPD
9 DP_LANE2_N 19 GND
10 DP_LANE3_P 20 DP_PWR
SPK_OUT1 : Speaker-out Jack (Green)
Connector Type: 5-pin Phone Jack
Pin Definition
1 GND
2 OUT_R
3 NC
4 GND
5 OUT_L
MIC_IN1: Microphone Jack (Pink)
Connector Type: 5-pin Phone Jack
Pin Definition
1 GND
2 MIC_R
3 NC
4 GND
5 MIC_L
DIO1: Digital Input / Output Connector
Connector Type: Terminal Block 1X10 10-pin, 3.5mm pitch
Pin Definition Pin Definition
1 DC INPUT 6 DO1
2 DI1 7 DO2
3 DI2 8 DO3
4 DI3 9 DO4
5 DI4 10 GND
Page 48
ACO-3000 l User’s Manual
48
Chapter 2: Switches and Connectors
PWR_SW2 : Remote Power Switch
Connector Type: Terminal Block 1X2 2-pin, 3.5mm pitch
Pin Definition
1 Power Button
2 GND
Page 49
ACO-3000 l User’s Manual
49
Chapter 2: Switches and Connectors
CN1: Mini PCI-Express / mSATA Socket
CN2: Mini PCI-Express / mSATA Socket
Pin
Definition
Pin
Definition
Pin
Definition
1 WAKE# 19 NC 37 GND
2 +3.3V 20 +3.3V 38 USB_D5+
3 NC 21 GND 39 +3.3V
4 GND 22 MINIPCIE RST# 40 GND
5 NC 23
MINIPCIE_RXN6_0
(SATA_RXN3)
41 +3.3V
6 +1.5V 24 +3.3V 42 NC
7 CLKREQ4# 25
MINIPCIE_RXP6_0
(SATA_RXP3)
43 GND
8 USIM1_VCC 26 GND 44 NC
9 GND 27 GND 45 NC
10 USIM1_DATA 28 +1.5V 46 NC
11 MINIPCIE_CLKN1 29 GND 47 NC
12 USIM1_CLK 30 SMB_CLK 48 +1.5V
13 MINIPCIE_CLKP1 31
MINIPCIE_TXN6_0
(SATA_TXN3)
49 NC
14 USIM1_RST 32 SMB_DATA 50 GND
15 GND 33
MINIPCIE_TXP6_0
(SATA_TXP3)
51 NC
16 USIM1_VPP 34 GND 52 +3.3V
17 NC 35 GND
18 GND 36 USB_D5-
Pin
Definition
Pin
Definition
Pin
Definition
1 WAKE# 19 NC 37 GND
2 +3.3V 20 +3.3V 38 USB_D6+
3 NC 21 GND 39 +3.3V
4 GND 22 MINIPCIE RST# 40 GND
5 NC 23
MINIPCIE_RXN6_1
(SATA_RXP2)
41 +3.3V
6 +1.5V 24 +3.3V 42 NC
7 CLKREQ5# 25
MINIPCIE_RXP6_1
(SATA_RXN2)
43 GND
8 USIM2_VCC 26 GND 44 NC
9 GND 27 GND 45 NC
10 USIM2_DATA 28 +1.5V 46 NC
11 MINIPCIE_CLKN2 29 GND 47 NC
12 USIM2_CLK 30 SMB_CLK 48 +1.5V
13 MINIPCIE_CLKP2 31
MINIPCIE_TXN6_1
(SATA_TXP2)
49 NC
14 USIM2_RST 32 SMB_DATA 50 GND
15 GND 33
MINIPCIE_TXP6_1
(SATA_TXN2)
51 NC
16 USIM2_VPP 34 GND 52 +3.3V
17 NC 35 GND
18 GND 36 USB_D6-
Page 50
ACO-3000 l User’s Manual
50
Chapter 2: Switches and Connectors
SATA1, SATA2: SATA with Power Connector
Pin
SATA1
Definition
Pin
SATA1
Definition
Pin
SATA2
Definition
Pin
SATA2
Definition
1 GND 12 GND 1 GND 12 GND
2
SATA_TXP0
13 GND 2 SATA_TXP1 13 GND
3
SATA_TXN0
14 +5V 3
SATA_TXN1
14 +5V
4 GND 15 +5V 4 GND 15 +5V
5
SATA_RXN0
16 +5V 5
SATA_RXN1
16 +5V
6
SATA_RXP0
17 GND 6
SATA_RXP1
17 GND
7 GND 18 GND 7 GND 18 GND
8 +3.3V 19 GND 8 +3.3V 19 GND
9 +3.3V 20 +12V 9 +3.3V 20 +12V
10 +3.3V 21 +12V 10 +3.3V 21 +12V
11 GND 22 +12V 11 GND 22 +12V
POWER1, POWER2: Power Connector
Connector Type: 1X4-pin Wafer, 2.0mm pitch
Pin Definition
1 +5V
2 GND
3 GND
4 +12V
Pin Definition Pin Definition Pin Definition Pin Definition
A1
PCIE_PRSNT1
A17 PEG_RXN0 B1 +12V B17 PRSNT2_1
A2 +12V A18 GND B2 +12V B18 GND
A3 +12V A19 NC B3 +12V B19 PEG_TXP1
A4 GND A20 GND B4 GND B20 PEG_TXN1
A5 NC A21 PEG_RXP1 B5 SMB_CLK B21 GND
A6 NC A22 PEG_RXN1 B6 SMB_DATA B22 GND
A7 NC A23 GND B7 GND B23 PEG_TXP2
A8 NC A24 GND B8 +3.3V B24 PEG_TXN2
A9 +3.3V A25 PEG_RXP2 B9 NC B25 GND
A10
+3.3V A26 PEG_RXN2 B10 +3.3VSB B26 GND
A11
PCIE_RESET# A27 GND B11 PCIE_WAKE# B27 PEG_TXP3
A12
GND A28 GND B12 NC B28 PEG_TXN3
A13
PEG_CLK_P A29 PEG_RXP3 B13 GND B29 GND
A14
PEG_CLK_N A30 PEG_RXN3 B14 PEG_TXP0 B30 NC
A15
GND A31 GND B15 PEG_TXN0 B31 PRSNT2_2
A16
PEG_RXP0 A32 NC B16 GND B32 GND
PCIE1: PCI-Express X4 Socket
Connector Type: PCI-Express X4 Slot
Page 51
ACO-3000 l User’s Manual
51
Chapter 2: Switches and Connectors
PWR_LED1: Power LED Status
Pin Definition
1 POWER LED+
2 POWER LED-
Pin Definition
1 HDD LED+
2 HDD LED-
HDD_LED1: HDD Access LED Status
Pin Definition
1 WATCHDOG LED+
2 WATCHDOG LED-
WDT_LED1: Watchdog LED Status
Pin Definition
1 GPIO LED+
2 GPIO LED-
GPIO_LED1: GPIO LED Status
Pin Definition
1 LINK LED+
2 LINK LED-100Mbps-
3 LINK LED 100Mbps-
LAN1_LINK1, LAN2_LINK1 : LAN Link LED Status
Pin Definition
1 ACTIVE LED+
2 ACTIVE LED-
LAN1_ACT1, LAN2_ACT1 : LAN Active LED Status
Pin Definition
1 TEMP LED+
2 TEMP LED-
TEMP_LED1: Temperature LED Status
Page 52
Chapter 3
System Setup
Page 53
ACO-3000 l User’s Manual
53
3.1 Set torque force to 3.5 kgf-cm to execute all the screwing and
unscrewing.
3.2 Removing chassis bottom cover
1. Turn the system upside down. Unscrew the 6 screws (M3x5L) on the bottom cover.
2. Now you can remove the bottom cover.
Chapter 3: System Setup
In order to prevent electric shock or system damage, before removing the
chassis cover, must turn off power and disconnect the unit from power source.
WARNING
Page 54
ACO-3000 l User’s Manual
54
3.3 Removing chassis top cover
1. Unscrew the four screws (M3x5L) highlighted below.
2. Hold the body of the system and lift it vertically away from the top cover.
3. Top cover separated from the system body.
Chapter 3: System Setup
Page 55
ACO-3000 l User’s Manual
55
3.4 Installing SODIMM
1. Place the system body with SODIMM socket facing upward.
2. Insert memory module from 45 degree direction.
3. Press the memory module vertically downward until you hear the “click” sound. Make sure
the memory module is firmly in place.
Chapter 3: System Setup
Page 56
ACO-3000 l User’s Manual
56
3.5 Installing mini PCIe card / mSATA
1. Two mini PCIe slots are available for ACO-3000 series. They both also support mSATA.
2. Insert mini PCIe card or mSATA module from 45 degree direction.
3. Press the mini PCIe card or mSATA module down and lock it with two screws (M2x3.7L).
Chapter 3: System Setup
Page 57
ACO-3000 l User’s Manual
57
3.6 Installing antenna
1. Three antenna holes are available for ACO-3000 series on the rear panel.
2. Remove antenna hole cover on the system panel.
3. Have antenna jack penetrate through the hole.
Chapter 3: System Setup
Page 58
ACO-3000 l User’s Manual
58
4. Put on washer and fasten the nut with antenna jack.
5. Attach the RF connector at the cable-end onto the communication module.
6. Assemble the antenna and antenna jack together.
Chapter 3: System Setup
Page 59
ACO-3000 l User’s Manual
59
3.7 Assembly chassis top cover
1. Place both top cover and system body upside down as shown below.
2. Ensure thermal pad is in place on the CPU thermal block.
3. Hold the system body and slide the front/rear panel into the slide rail on the top cover.
Chapter 3: System Setup
Page 60
ACO-3000 l User’s Manual
60
4. Push the system body down until it is firmly in place.
5. Fasten the four screws (M3x5L) to lock the system body with top cover.
Chapter 3: System Setup
Page 61
ACO-3000 l User’s Manual
61
3.8 Installing HDD on internal SATA HDD bay
1. Unscrew the below four screws (M3x5L) to remove the internal SATA HDD bay.
2. Lock the 2.5” HDD with HDD bracket using four screws (M3x4L).
Chapter 3: System Setup
Page 62
ACO-3000 l User’s Manual
62
3. Install the HDD bracket following the direction below.
4. Fasten the four screws to lock the internal HDD bracket.
Chapter 3: System Setup
Page 63
ACO-3000 l User’s Manual
63
3.9 Installing HDD on removable SATA HDD bay
1. Unscrew the two sun screws circled below to take out the removable SATA HDD bay.
2. Lock the 2.5” HDD with HDD bracket using four screws (M3x4L).
Chapter 3: System Setup
Page 64
ACO-3000 l User’s Manual
64
3. Slide the HDD bracket back and then fasten the sun screws.
Chapter 3: System Setup
Page 65
ACO-3000 l User’s Manual
65
3.10 Assemble chassis bottom cover
1. Place the bottom cover according to the below direction and make sure the rail is facing inside
the system.
2. Lock the bottom cover with the four screws (M3x5L).
Chapter 3: System Setup
Page 66
ACO-3000 l User’s Manual
66
3.11 Installing SIM card
1. Take out the removable SATA HDD bay in order to locate the SIM card slot.
2. Now you can insert SIM card into the socket.
3. Please note that the installation of SIM 1 and SIM 2 has to match the installation of mini PCIe
slots.
4. To uninstall SIM card, simply press the installed SIM card and then the card will be pushed out.
Chapter 3: System Setup
SIM 1 SIM 2
SIM Card Socket Number
Matching Mini PCIe Slot
SIM 1
Mini
PCIe 1 / mSATA (CN1)
SIM 2
Mini
PCIe 2 / mSATA (CN2)
Page 67
ACO-3000 l User’s Manual
67
3.12 To configure Power Ignition settings
1. Ignition Power Control Area is available for ACO-3000 series on the front panel.
2. Unscrew the below screw to remove the control area cover.
3. Now you can configure Car Mode Delay Time Setting Switch, PC/Car Mode Select Switch, and
Car Mode Input Power Select Switch.
Chapter 3: System Setup
Page 68
ACO-3000 l User’s Manual
68
3.13 Installing wall mount kit
1. Wall mount kit is available for ACO-3000 series included in the standard package.
2. Place the system upside down so you can see the bottom cover. The highlighted screw holes
below will be used.
3. Lock the wall mount kit with eight screws (M3x5L, Nylok).
Chapter 3: System Setup
Page 69
ACO-3000 l User’s Manual
69
3.14 Installing DIN rail holder
1. Din rail holder is available for ACO-3000 series as optional accessories.
2. Place the system upside down so you can see the bottom cover with two screw holes for din
rail holder.
3. Place the din rail holder on top of the bottom cover and lock it with two screws (M4x5L,
Nylok).
Chapter 3: System Setup
Page 70
Chapter 4
BIOS Setup
Page 71
ACO-3000 l User’s Manual
71
4.1 BIOS Introduction
The system BIOS software is stored on EEPROM. The BIOS provides an interface to modify the
configuration. When the battery is removed, all the parameters will be reset.
BIOS Setup
Power on the embedded system and by pressing <Del> or <F2> immediately allows you to enter the
setup screens. If the message disappears before you respond and you still wish to enter the Setup, restart
the system by turning it OFF and ON or pressing the RESET button.
You may also restart the system by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys.
Chapter 4: BIOS Setup
Control Keys
<←> <→>
Select Screen
<↑> <↓>
Select Item
<Enter>
Select
<Page Up/+>
Increases the numeric value or makes changes
<Page Down/
->
Decreases the numeric value or makes changes
<F1>
General Help
<F2>
Previous Value
<F3>
Load Optimized Defaults
<F4>
Save Configuration and Exit
<Tab>
Select Setup Fields
<Esc>
Exit BIOS Setup
Main Setup
The main menu lists the setup functions you can make changes to. You can use the arrow keys ( ↑↓ ) to
select the item. The on-line description of the highlighted setup function is displayed at the bottom of
the screen.
General Help <F1>
The BIOS setup program provides a General Help screen. You can call up this screen from any menu by
simply pressing <F1>. The Help screen lists the appropriate keys to use and the possible selections for the
highlighted item. Press <Esc> to exit the Help screen.
Page 72
ACO-3000 l User’s Manual
72
4.2 Main Setup
Press <Del> to enter BIOS CMOS Setup Utility. The Main setup screen is showed as following when the
setup utility is entered. System Date/Time is set up in the Main Menu.
Chapter 4: BIOS Setup
4.2.1 System Language
Set the system language. Please use <Tab> to switch between language elements.
4.2.1 System Date
Set the system date. Please use <Tab> to switch between data elements.
4.2.2 System Time
Set the system time. Please use <Tab> to switch between time elements.
Page 73
ACO-3000 l User’s Manual
73
4.3 Advanced Setup
4.3.1 CPU Configuration
Chapter 4: BIOS Setup
■ Hyper-Threading
This item allows you to enable or disable the Intel Hyper-Threading Technology.
■ Active Processor Cores
Set number of cores to be enabled. Select <All> or <1> mode.
Page 74
ACO-3000 l User’s Manual
74
Chapter 4: BIOS Setup
4.3.2 ACPI Settings
■ Enable ACPI Auto Configuration
This item allows you to enable or disable BIOS ACPI Auto Configuration.
■ Enable Hibernation
This item allows you to enable or disable system ability to hibernate.
Enhanced C1 State
This item allows your CPU reduce power consumption when the system is in idle mode.
CPU C3 Report
This item allows you to enable or disable the CPU C3 report to the operating system.
CPU C6 Report
This item allows you to enable or disable the CPU C6 report to the operating system.
CPU C7 Report
This item allows you to enable or disable the CPU C7 report to the operating system.
■ Execute Disable Bit
Enable or disable the Execute Disable Bit (XD) of the processor. With the XD bit set to enabled,
certain classes of malicious buffer overflow attacks can be prevented when combined with a
supporting OS
■ Intel Virtualization Technology
When enabled, a VMM can utilize the integrated hardware virtualization support .
■ CPU AES
This item allows you to enable or disable CPU Advanced Encryption Standard (AES) instructions.
■ EIST
This item allows you to enable or disable Enhanced Intel SpeedStep Technology (EIST).
■ CPU C states
This item allows you to set the power saving of the CPU states.
Page 75
ACO-3000 l User’s Manual
75
Chapter 4: BIOS Setup
■ Intel AMT
This item allows you to enable or disable Intel Active Management Technology BIOS Extension.
■ BIOS Hotkey Pressed
This item allows you to enable or disable BIOS Hotkey Press function.
■ MEBx Selection Screen
This item allows you to enable or disable MEBx Selection Screen function.
■ Active Remote Assistance Process
This item allows you to enable or disable Trigger CIRA boot function.
4.3.3 AMT Configuration
Use this screen to configure AMT parameters.
Page 76
ACO-3000 l User’s Manual
76
Chapter 4: BIOS Setup
4.3.4 Super IO Configuration
This setting allows you to select options for the Super IO Configuration, and change the value of
the selected option.
■ Serial Port 1 Configuration
Serial Port
This item allows you to enable or disable serial port.
Change Settings
This item allows you to change the address & IRQ settings of the specified serial port.
Device Type Select
Change the Serial interface. Select <RS232> ,<RS422 Full Duplex> or <RS485 Half Duplex> interface.
Page 77
ACO-3000 l User’s Manual
77
■ Serial Port 2 Configuration
Chapter 4: BIOS Setup
Serial Port
This item allows you to enable or disable serial port.
Change Settings
This item allows you to change the address & IRQ settings of the specified serial port.
Device Type Select
Change the Serial interface. Select <RS232> ,<RS422 Full Duplex> or <RS485 Half Duplex> interface.
■ Serial Port 3 Configuration
Serial Port
This item allows you to enable or disable serial port.
Change Settings
This item allows you to change the address & IRQ settings of the specified serial port.
Device Type Select
Change the Serial interface. Select <RS232> ,<RS422 Full Duplex> or <RS485 Half Duplex> interface.
Page 78
ACO-3000 l User’s Manual
78
■ Serial Port 4 Configuration
Serial Port
This item allows you to enable or disable serial port.
Change Settings
This item allows you to change the address & IRQ settings of the specified serial port.
Device Type Select
Change the Serial interface. Select <RS232> ,<RS422 Full Duplex> or <RS485 Half Duplex> interface.
Chapter 4: BIOS Setup
■ Watch Dog Function
You can setup the system watch-dog timer, a hardware timer that generates a reset
when the software that it monitors does not respond as expected each time the watch
dog polls it.
Watch Dog Timer Count Mode
Change the Watch dog mode. Select <Second Mode> or <Minute Mode> mode.
Watch Dog Timer Time Out Value
User can set a value in the range of 0 to 255.
Page 79
ACO-3000 l User’s Manual
79
Chapter 4: BIOS Setup
4.3.5 Hardware Monitor
These items display the current status of all monitored hardware devices/ components such as voltages
and temperatures.
4.3.6 Serial Port Console Redirection
■ Console Redirection
This item allows you to enable or disable console redirection.
Page 80
ACO-3000 l User’s Manual
80
Chapter 4: BIOS Setup
4.3.7 SATA Configuration
■ SATA Controller(s)
This item allows you to enable or disable SATA Controller.
■ SATA Mode Selection
This item allows you to select AHCI or RAID Mode.
■ SATA Controller Speed
The item is for user to set the maximum speed the SATA controller can support. Change
the SATA Speed. Select <Default>, <Gen1>, <Gen2> or <Gen3> speed.
■ Serial ATA Port 0 / 1 / 2 / 3
Port 0 / 1 / 2 / 3
This item allows you to enable or disable Serial ATA Port 0 / 1 / 2 / 3.
Hot Plug
This item allows you to enable or disable hot plug function.
SATA Device Type
Identify if the relevant SATA port is connected to Hard Disk Drive or Solid State Drive.
Page 81
ACO-3000 l User’s Manual
81
Chapter 4: BIOS Setup
4.3.8 Network Stack Configuration
■ Network Stack
Use this item to enable or disable UEFI Network Stack.
Page 82
ACO-3000 l User’s Manual
82
Chapter 4: BIOS Setup
4.3.9 CSM Configuration
■ CSM Support
This item allows you to enable or disable CSM support.
■ GateA20 Active
This item allows you to select <Upon Request> or <Always>.
Upon Request: GA20 can be disabled using BIOS services.
Always: Do not allow GA20 disabling. This option is useful when any RT code is executed
above 1MB.
■ Option ROM Messages
This item allows you to select <Force BIOS> or <Keep Current>.
Force BIOS : The third-party ROM messages will be forced to display during the boot
sequence.
Keep Current : The third-party ROM messages will be displayed only if the third-party
manufactured had set the add-on device to do so.
■ Boot option filter
This item allows you to select which type of operating system to boot.
UEFI and Legacy: Allows booting from operating systems that support legacy option ROM
or UEFI option ROM.
Legacy only: Allows booting from operating systems that only support legacy option ROM.
UEFI only: Allows booting from operating systems that only support UEFI option ROM.
■ PXE Function
This item controls the execution of UEFI and PXE option ROM. Select <Do not launch>,
<UEFI> or <Legacy>.
■ Storage
This setting allows you to select whether to enable the UEFI or legacy option ROM for the
storage device controller. Select <Do not launch>, <UEFI> or <Legacy>.
■ Video
This setting allows you to select whether to enable the UEFI or legacy video option ROM
for the video device controller. Select <Do not launch>, <UEFI> or <Legacy>.
■ Other PCI devices
This item determines option ROM execution policy for devices other than Network,
storage or video. Select <Do not launch>, <UEFI> or <Legacy>.
Page 83
ACO-3000 l User’s Manual
83
4.3.10 USB Configuration
Chapter 4: BIOS Setup
■ Legacy USB Support
This item allows you to select <Enabled>, <Disabled> or <Auto>.
Enabled: To enable legacy USB support.
Disabled: To keep USB devices available only for EFI specification,
Auto: To disable legacy support if no USB devices are connected.
■ XHCI Hand-off
This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be
claimed by XHCI driver. Select <Enabled> or <Disabled>.
■ EHCI Hand-off
This is a workaround for OSes without EHCI hand-off support. The EHCI ownership change should be
claimed by EHCI driver. Select <Enabled> or <Disabled>.
■ USB Mass Storage Driver Support
Enables or disables support for USB storage devices.
■ USB Transfer time-out
Use this item to set the time-out value for control, bulk, and interrupt transfers. Select <1 sec>, <5 sec>,
<10 sec> or <20 sec>.
■ Device reset time-out
Use this item to set USB mass storage device start unit command time-out. Select <10 sec>, <20 sec>,
<30 sec> or <40 sec>.
■ Device power-up delay
Maximum time the device will take before it properly reports itself to the Host Controller. “Auto” uses
default value: for a Root port it is 100ms, for a Hub port the delay is taken from Hub descriptor.
Page 84
ACO-3000 l User’s Manual
84
4.3.11 Intel(R) Ethernet Connection I218-LM-XX:XX:XX:XX:XX:XX
Chapter 4: BIOS Setup
■ NIC Configuration
Press enter to configure the network device port.
■ Blink LEDs
Use this item to identify the physical network port by blinking the associated LED.
■ Link Status
Use this item to specify the port speed used for the selected boot protocol. Select <Auto Negotiated>,
<10 Mbps Half>, <10 Mbps Full>, <100 Mbps Half> or <100 Mbps Full>.
Link Speed
Use this item to specify the port speed used for the selected boot protocol. Select <Auto
Negotiated>, <10 Mbps Half>, <10 Mbps Full>, <100Mbps Half> or <100 Mbps Full>.
Wake On LAN
Enables the server to be powered on using an in-band magic packet.
Page 85
ACO-3000 l User’s Manual
85
4.3.12 Intel(R) I210 Gigabit Network Connection- XX:XX:XX:XX:XX:XX
Chapter 4: BIOS Setup
■ NIC Configuration
Press enter to configure the network device port.
■ Blink LEDs
Use this item to identify the physical network port by blinking the associated LED.
■ Link Status
Use this item to specify the port speed used for the selected boot protocol. Select <Auto Negotiated>,
<10 Mbps Half>, <10 Mbps Full>, <100 Mbps Half> or <100 Mbps Full>.
■ Virtual MAC Address
Displays the programmatically assignable MAC Address.
Link Speed
Use this item to specify the port speed used for the selected boot protocol. Select <Auto
Negotiated>, <10 Mbps Half>, <10 Mbps Full>, <100Mbps Half> or <100 Mbps Full>.
Wake On LAN
Enables the server to be powered on using an in-band magic packet.
Page 86
ACO-3000 l User’s Manual
86
4.4 Chipset
4.4.1 System Agent (SA) Configuration
Chapter 4: BIOS Setup
■ VT-d
This item allows you to enable or disable VT-d support.
Page 87
ACO-3000 l User’s Manual
87
Chapter 4: BIOS Setup
GTT Size
This item allows you to change the GTT size.
Aperture Size
This item allows you to change the Aperture size.
CD Clk Frequency
This item allows you to change the CD Clock Frequency.
DVMT Pre-Allocated
Used the DVMT Pre-Allocated option to specify the amount of system memory that can be used by
the internal graphics device.
DVMT Total Gfx Mem
This setting specifies the memory size for DVMT.
Primary IGFX Boot DisplayUse the field to select the type of device you want to use as the
display(s) of the system.
▶ Graphics Configuration
Use this item to configure internal graphics controller.
Page 88
ACO-3000 l User’s Manual
88
Chapter 4: BIOS Setup
4.4.2 PCH-IO Configuration
▶ PCI Express Configuration
Page 89
ACO-3000 l User’s Manual
89
Chapter 4: BIOS Setup
PCI Express Root Port 1 / 2 / 4 / 5 / 6
PCI Express Port 1 / 2 / 4 / 5 / 6
This item allows you to enable or disable PCI Express Port 2 / 4 / 5 / 6 in the chipset.
ASPM
This item allows you to select the ASPM state for energy-saving. Select <Disabled> ,<L0s>, <L1>, <L0sL1>
or <Auto>
Hot Plug
This item allows you to enable or disable hot plug function.
PCIe Speed
Change the PCIe Port Speed. Select <AUTO> ,<Gen 1> or <Gen 2>
Page 90
ACO-3000 l User’s Manual
90
Chapter 4: BIOS Setup
90
Chapter 4: BIOS Setup
90
Chapter 4: BIOS Setup
90
Chapter 4: BIOS Setup
USB Precondition
Precondition work on USB host controller and root ports for faster enumeration.
XHCI Mode
Mode of operation of XHCI controller.
BTCG
This item allows you to enable or disable trunk clock gating.
USB Ports Per-Port Disable Control
This item allows you to enable or disable each of the USB ports.
▶ USB Configuration
Azalia
Control Detection of the Azalia device. This item allows you to select <Enabled>, <Disabled> or <Auto>.
Disabled: Azalia will be unconditionally be disabled.
Enabled: Azalia will be unconditionally be enabled.
Auto: Azalia will be enabled if present, disabled otherwise.
▶ PCH Azalia Configuration
Page 91
ACO-3000 l User’s Manual
91
Chapter 4: BIOS Setup
91
Chapter 4: BIOS Setup
91
Chapter 4: BIOS Setup
91
Chapter 4: BIOS Setup
■ PCH LAN Controller
This item allows you to enable or disable the onboard PCH integrated ethernet controller.
■ Wake on LAN
This item allows you to enable or disable wake on LAN function.
■ Restore AC Power Loss
This item specifies whether your system will reboot after a power failure or interrupt occurs. Available
settings are:
Power Off: Leave the computer in the power off state.
Power On: Leave the computer in the power on state.
Last State: Restore the system to the previous status before power failure or interrupt occurred.
4.5 Security
Security menu allow users to change administrator password and user password settings.
4.5.1 Administrator Password
This item allows you to set Administrator Password.
4.5.2 User Password
This item allows you to set User Password.
Page 92
ACO-3000 l User’s Manual
92
4.6 Boot
This menu allows you to setup the system boot options.
4.6.1 Setup Prompt Timeout
This item sets number of seconds to wait for setup activation key.
4.6.2 Bootup NumLock State
This item selects the keyboard NumLock state. Select <On> or <Off>.
4.6.3 Full Screen Logo Show
This item allows you to enable or disable Full Screen Logo Show function.
4.6.4 Fast Boot
This item allows you to enable or disable boot with initialization of a minimal set of
devices required to launch active boot option. Has no effect for BBS boot options.
4.6.5 Hard Driver BBS Priorities
The items specify the boot device priority sequence from the available devices. The
number of device items that appears on the screen depends on the number of
devices installed in the system.
Chapter 4: BIOS Setup
Page 93
ACO-3000 l User’s Manual
93
4.7 Save & Exit
This setting allows users to configure the boot settings.
4.7.1 Save Changes and Reset
This item allows user to reset the system after saving the changes.This item allows user
to reset the system after saving the changes.
4.7.2 Discard Changes and Reset
This item allows user to reset the system without saving any changes.
4.7.3 Restore Defaults
Use this item to restore /load default values for all the setup options.
4.7.4 Launch EFI Shell from filesystem device
Use this item to launch EFI shell application (shell.efi) from one of the available
filesystem device.
Chapter 4: BIOS Setup
Page 94
Appendix
WDT & GPIO
This appendix provides the sample codes of WDT (Watch
Dog Timer) and GPIO (General Purpose Input/ Output).
Page 95
ACO-3000 l User’s Manual
95
WDT Sample Code
SIO_INDEX_Port equ 02Eh
SIO_DATA_Port equ 02Fh
SIO_UnLock_Value equ 087h
SIO_Lock_Value equ 0AAh
WatchDog_LDN equ 007h
WDT_UNIT equ 60h ;60h=second, 68h=minute, 40h=Disabled Watchdog timer
WDT_Timer equ 30 ;ex. 30 seconds
Sample code:
;Enable config mode
mov dx, SIO_INDEX_Port
mov al, SIO_UnLock_Value
out dx, al
jmp short $+2 ;Io_delay
jmp short $+2 ;Io_delay
out dx, al
;Change to WDT
mov dx, SIO_INDEX_Port
mov al, 07h
out dx, al
mov dx, SIO_DATA_Port
mov al, WatchDog_LDN
out dx, al
;Acive WDT
mov dx, SIO_INDEX_Port
mov al, 30h
out dx, al
mov dx, SIO_DATA_Port
in al, dx
or al, 01h
out dx, al
;set timer
mov dx, SIO_INDEX_Port
mov al, 0F6h
out dx, al
mov dx, SIO_DATA_Port
mov al, WDT_Timer
out dx, al
;set UINT
mov dx, SIO_INDEX_Port
mov al, 0F5h
out dx, al
mov dx, SIO_DATA_Port
mov al, WDT_UNIT
out dx, al
;enable reset
mov dx, SIO_INDEX_Port
mov al, 0Fah
out dx, al
mov dx, SIO_DATA_Port
in al, dx
or al, 01h
out dx, al
;close config mode
mov dx, SIO_INDEX_Port
mov al, SIO_Lock_Value
out dx, al
Appendix – WDT & GPIO
Page 96
ACO-3000 l User’s Manual
96
GPIO Sample Code
GPI 1 ~ GPI 4
GPO 1 ~ GPO 4
GPI_REG equ 0A03h
GPO_REG equ 0A02h
GPO_0 equ 00010000b
____________________________________________________________________________________
Sample Code:
#1 : Get GPI 0 status
; Get GPI 0 Pin Status Register
In al, GPI_REG
;al bit0 = GPI 0 status
#2 : Set GPO 0 status to high
; Set GPO 0 Pin to High
mov dx, GPO_REG
in al, dx
or al, GPO_0
out dx, al
;al bit4 = GPO 0 status
Appendix – WDT & GPIO
GPI 0 GPI 1 GPI 2 GPI 3
IO Address 0xA03h 0xA03h 0xA03h 0xA03h
Bit 4 5 6 7
Sample code #1
GPO 0 GPO 1 GPO 2 GPO 3
IO Address 0xA02h 0xA02h 0xA02h 0xA02h
Bit 0 1 2 3
Sample code #2
Page 97
Copyright © C&T Solution Inc. All Rights Reserved
www.candtsolution.com
Loading...