CTS WPS-3005 operation manual

Trademarks

WPS/MPS-3005 Ethernet Switch

User’s Guide

Installation Guide



Attach fiber cable from the Switch to the fiber network.



Attach a UTP cable from the 10/100/1000Base-T network to the RJ-45 port on the Switch.



Connect the power adapter to the Switch and the Power LED will light up. The Link/ACT/Speed and F/O Link/ACT LEDs will light up as soon as all the cable connections are satisfactory.

Auto-Negotiation in TP port

Store and Forward Switching Mechanism

Auto-detecting full/half duplex mode operation

MDI/MDIX Auto-Crossover

Flow Control

Power and F/O port failure alarm

2K MAC address table

9K bytes Jumbo Frame

Wide range of operating temperature (-20oC~60oC)

DIN Rail and wall mounting installation

Redundant AC and DC power supply

Use flat-head screwdriver to loosen and tighten the screw.

Insert positive or negative wire as indicated.

CTS is a registered trademark of Connection Technology Systems Inc. Contents subject to revision without prior notice.

All other trademarks remain the property of their owners.

any way whatsoever unless prior consent has been obtained from Connection Technology Systems Inc.

FCC Warning

These devices have been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These standards are designed to provide reasonable protection against harmful interference when these devices are operated in a commercial environment. These devices generate, use, and can radiate radio frequency energy and may cause harmful interference to radio communications unless installed in

accordance with this User’s Guide. Operation of these devices in a

residential area is likely to cause harmful interference which will make the user responsible for the appropriate remedial action at his / her own expense.

CE Mark Warning

These are Class A products. In a domestic environment these products may cause radio interference in which case the user will need to consider adequate preventative methods.

1. Checklist

The package should contain the following items:

2. Overview

WPS/MPS-3005 Ethernet Switches support IEEE802.3at PoE feature and are specifically designed to supply power to PoE-enabled devices such as WiFi AP or surveillance cameras. They are power supply equipments (PSE) that can transmit data and supply power at the same time to the powered devices (PD). The maximum cable distance that can reach the powered devices from WPS-3005 is up to 80M, allowing your powered devices to be installed in a place where power is not easily accessible.

Besides, WPS/MPS-3005 Series Ethernet Switches aim at industrial applications that demand wide range of operating temperature and require redundant power supplies to create a reliable and stable networking environment in the event of power failure. They can also be mounted on the wall or onto 35mm DIN rail using DIN rail clip on the Switch. The installation and operation procedures are simple and straightforward. Operation status can be locally monitored through a set of diagnostic LED indicators located on the front panel.

Major Features:

3. Network Installation

Please follow the steps described below and refer to Figure 1 and 2 to complete the network installation.

WPS-3005 MPS-3005

Figure 1. Network Installation for FC Models

WPS-3005 MPS-3005

Figure 2. Network Installation for WDM/SFP Models

4. Terminal Block

TB1 and TB2 Power Supply: There are two pairs of contacts on

the terminal block connector for power redundancy purpose. You can use both pairs of power supply for redundancy purpose or use either one pair of power supply on the terminal block and AC external power supply to create redundant setup. The redundant power supply will take over seamlessly when one power source is down to protect your device or network from the loss of power. When you use only one power supply (no redundant power is available), the LED Power/Port Status will flash in orange to alert the user.

Please notify your sales representative immediately if any item is missing or damaged.

As for power adapters, please refer to Section 7 for more detailed information.

Figure 3. Terminal Block Front and Top View

Port Fault Alarm: One pair of port fault connection on the terminal block is used to connect alarm devices such as speakers or LEDs to alert users when the F/O port link is disconnected.

5. LED Description

Standards

IEEE 802.3, 802.3u, 802.3x, 802.3z, 802.3ab,

802.3at

Interface

4 X Shielded 10/100/1000Base-T RJ45 1 X 1000Base-X Fiber

LED

PWR, PW T1, PW T2, F/O Link/ACT PWR/Port Status, Link/ACT/Speed, PoE

Power

DC Input Voltage: 48VDC DC Power Jack x 1; DC Terminal Block x 2

Shipping Weight

WPS-3005: 0.4KG ; MPS-3005: 0.6KG

Dimensions

WPS-3005: 105mm(W)X93mm(D)X61mm(H) MPS-3005: 121mm(W)X99mm(D)X61mm(H)

Temperature

Operating: -20oC~60oC; Storage: -20oC~70oC

Humidity

5%~90% RH non-condensing

EMC Safety

FCC Part 15 Class A, CE

Media

TP:

EIA/TIA-568 CAT 5e

Fiber:

50/125, 62.5/125um multi-mode fiber

9/125, 10/125um single-mode fiber

*Please contact us for further reports and updates.

MODEL

Connector

Type

Volt/Watt

PSE Power

Feeding

Function

WAP-POWER-12J18

DC Jack

12V/18W

WAP-POWER-48J90

DC Jack

48V/90W

WAP-POWER-48D75

Terminal Block

48V/75W

WAP-POWER-48D240

Terminal Block

48V/240W

TYPE

BTFC

Connector Type

Wavelength

850nm

Typical Distance

500m

Min/Max TX PWR

-9.5dBm/-4.0dBm

Sensitivity

-18.0dBm

Link Budget

8.5dB

TYPE

BTFC(SM-10)

BTFC(SM-20)

BTFC(SM-30)

Connector Type

Wavelength

1310nm

Typical Distance

10Km

20Km

30Km

Min TX PWR

-9.5dBm

-5.0dBm

Max TX PWR

-3.0dBm

3.0dBm

Sensitivity

-20.0dBm

-24.0dBm

Link Budget

10.5dB

19.0dB

TYPE

W2A(SM-10)

W2B(SM-10)

W2A(SM-20)

W2B(SM-20)

Connector Type

TX Wavelength

1310nm

1550nm

1310nm

1550nm

RX Wavelength

1550nm

1310nm

1550nm

1310nm

Typical Distance

10 Km

20 Km

Min TX PWR

-10.0dBm

-9.0dBm

-7.0dBm

Max TX PWR

-3.0dBm

0dBm

Sensitivity

-22.0dBm

-23.0dBm

Link Budget

12.0 dB

13.0 dB

16.0 dB

LED

Color

Function

PWR

Green

AC or DC power is available.

PW T1

Green

Terminal Block 1 powers up.

PW T2

Green

Terminal Block 2 powers up.

F/O

Link/ACT

Green

F/O link is up.

Blinking

Green

F/O is receiving and transmitting data.

PWR/Port

Status

Orange

F/O link is down.

Blinking Orange

Redundancy system is abnormal (only one power source is available).

Link/ACT/

Speed

OFF

TP link is down or works at 10M.

Green

TP link is up and works at 100M

Orange

TP link is up and works at 1000M

Blinking

TP is receiving and transmitting data.

PoE

Green

Power feeding is on for 802.3af applications when the LED is steady on.

Power feeding is on for 802.3at applications when the LED is blinking slowly.

OFF

No link is detected, and the LED will blink green every 1 to 2 seconds.

Fiber Transceiver Information

6. Technical Specifications

7. Optional Accessory

Power Adapters:

1000M Multi-Mode

Single-Mode

Wave-Length WDM

NOTE: Specifications may change without prior notice.

Contact Information

 Connection Technology Systems INC (CTS)

18F-6, No.79, Sec.1, Xintai 5th Rd., Xizhi Dist., New Taipei City 221, TAIWAN, R.O.C. TEL: +886 2 26989661 FAX: +886 2 26989662 E-Mail: info@ctsystem.com

WPS-3005/MPS-3005

Series

4 Ports 10/100/1000Base-T

and 1 Port 1000Base-X

Gigabit Ethernet Switch

with Built-in IEEE802.3at

PoE/PSE Feature and

Extended Operating

Temperature

User’s Guide

Version 1.1

CTS WPS-3005 operation manual

Specifications and Main Features

Frequently Asked Questions

User Manual