CTS WAS-3005 Service Manual

Trademarks

WAS-3005 Ethernet Switch

User’s Guide

Installation Guide



Attach fiber cable from WAS-3005 to the fiber network.



Attach a UTP cable from the 10/100/1000Base-TX network to the RJ-45 port on WAS-3005.



Connect the power adapter to WAS-3005 and the Power LED will light up. The Link/ACT/Speed and F/O Link/ACT LEDs will light up as soon as all the cable connections are satisfactory.

Auto-Negotiation in TP port

Store and Forward Switching Mechanism

Auto-detecting full/half duplex mode operation

MDI/MDIX Auto-Crossover

Flow Control

Power and F/O port failure alarm

2K MAC address table

9K bytes Jumbo Frame

Wide-range operating temperature (-20oC~60oC)

DIN Rail and wall mounting installation

Redundant AC and DC power supply

Connect to

1000BASE-X

Fiber Network

Connect to

10/100/1000

BASE-T Network

Use flat-head screwdriver to loosen and tighten the screw.

Insert positive or negative wire as indicated.

TX/RX

Connect to

10/100/1000

BASE-T Network

Connect to SC/ST

1000BASE-X

Fiber Network

CTS is a registered trademark of Connection Technology Systems Inc. Contents subject to revision without prior notice.

All other trademarks remain the property of their owners.

any way whatsoever unless prior consent has been obtained from Connection Technology Systems Inc.

FCC Warning

These Ethernet switches have been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These standards are designed to provide reasonable protection against harmful interference when these devices are operated in a commercial environment. These devices generate, use, and can radiate radio frequency energy and may cause harmful interference to radio communications unless

installed in accordance with this User’s Guide. Operation of these

devices in a residential area is likely to cause harmful interference which will make the user responsible for the appropriate remedial action at his / her own expense.

CE Mark Warning

These are Class A products. In a domestic environment these products may cause radio interference in which case the user will need to consider adequate preventative methods.

1. Checklist

The package should contain the following items:

2. Overview

WAS-3005 Series Ethernet Switches are designed to meet the massive needs for Fast Ethernet network deployments and aim at industrial applications that demand wide range of operating temperature. They are fully compliant with IEEE802.3, 802.3u,

802.3x, 802.3z and 802.3ab standards. Via single mode fiber cable, they are able to extend a copper-based network to a maximum distance up to 100KM.

Besides, redundant AC and DC power supplies are both offered on WAS-3005 Series Ethernet Switches for users to create a reliable and stable network in the event of power failure. They can also be mounted on the wall or onto 35mm DIN rail using DIN rail clip on the Ethernet switch. The installation and operation procedures are simple and straightforward. Operation status can be locally monitored through a set of diagnostic LED indicators located on the front panel.

Major Features:

3. Network Installation

Please follow the steps described below and refer to Figure 1 and 2 to complete the network installation.

Figure 1. Network Installation for WAS-3005FX Models

Figure 2. Network Installation for WAS-3005WDM/SFP Models

4. Terminal Block

TB1 and TB2 Power Supply: There are two pairs of contacts on

the terminal block connector for power redundancy purpose. You can use both pairs of power supply for redundancy purpose or use either one pair of power supply on the terminal block and AC external power supply to create redundant setup. The redundant power supply will take over seamlessly when one power source is down to protect your device or network from the loss of power. When you use only one power supply (no redundant power is available), the Power/Port Status LED will light up in orange to alert the user.

Please notify your sales representative immediately if any item is missing or damaged.

As for power adapters, please refer to Section 7 for more detailed information.

Port Fault Alarm: One pair of port fault connection on the terminal block is used to connect alarm devices such as speakers or LEDs to alert users when the F/O port link is disconnected.

Figure 3. Terminal Block Front and Top View

5. LED Description

Standards

IEEE 802.3, 802.3u, 802.3x, 802.3z, 802.3ab

Interface

4 X Shielded 10/100/1000Base-T RJ45 1 X 1000Base-X Fiber

LED

PWR, PW T1, PW T2, F/O Link/ACT PWR/Port Status , Link/ACT/Speed

Power

DC Input Voltage: 12/48VDC DC Power Jack x 1; DC Terminal Block x 2

Power Consumption

4.6W Max.

Shipping Weight

0.45KG

Dimensions

105mm(W)X93mm(D)X61mm(H)

Temperature

Operating: -20oC~60oC; Storage: -20oC~70oC

Humidity

5%~90% RH non-condensing

EMC Safety

FCC Part 15 Class A, CE

Media

TP:

EIA/TIA-568 CAT 5e

Fiber:

50/125, 62.5/125um multi-mode fiber

9/125, 10/125um single-mode fiber

*Please contact us for further reports and updates.

MODEL

Connector Type

Volt/Watt

WAP-POWER-12J18

DC Jack

12V/18W

WAP-POWER-48J90

DC Jack

48V/90W

WAP-POWER-48D75

Terminal Block

48V/75W

WAP-POWER-48D240

Terminal Block

48V/240W

TYPE

BTFC

Connector Type

Wavelength

850nm

Typical Distance

500m

Min/Max TX PWR

-9.5dBm/-4.0dBm

Sensitivity

-18.0dBm

Link Budget

8.5dB

TYPE

BTFC(SM-10)

BTFC(SM-20)

BTFC(SM-30)

Connector Type

Wavelength

1310nm

Typical Distance

10Km

20Km

30Km

Min TX PWR

-9.5dBm

-5.0dBm

Max TX PWR

-3.0dBm

3.0dBm

Sensitivity

-20.0dBm

-24.0dBm

Link Budget

10.5dB

19.0dB

TYPE

W2A(SM-10)

W2B(SM-10)

W2A(SM-20)

W2B(SM-20)

Connector Type

TX Wavelength

1310nm

1550nm

1310nm

1550nm

RX Wavelength

1550nm

1310nm

1550nm

1310nm

Typical Distance

10 Km

20 Km

Min TX PWR

-10.0dBm

-9.0dBm

-7.0dBm

Max TX PWR

-3.0dBm

0dBm

Sensitivity

-22.0dBm

-23.0dBm

Link Budget

12.0 dB

13.0 dB

16.0 dB

LED

Color

Function

PWR

Green

AC or DC power is available.

PW T1

Green

Terminal Block 1 powers up.

PW T2

Green

Terminal Block 2 powers up.

F/O

Link/ACT

Green

F/O link is up.

Blinking

Green

F/O is receiving and transmitting data.

PWR/Port

Status

Orange

F/O link is down.

Blinking

Orange

Redundancy system is abnormal (only one power source is available).

Link/ACT/

Speed

Off

TP link is down or works at 10M.

Green

TP link is up and works at 100M

Orange

TP link is up and works at 1000M

Blinking

Green

TP is receiving and transmitting data.

Fiber Transceiver Information

6. Technical Specifications

7. Optional Accessory

Power Adapters:

1000M Multi-Mode

Single-Mode

Wave-Length WDM

NOTE: Specifications may change without prior notice.

Contact Information

 Connection Technology Systems INC (CTS)

18F-6, No.79, Sec.1, Xintai 5th Rd., Xizhi Dist., New Taipei City 221, TAIWAN, R.O.C. TEL: +886 2 26989661 FAX: +886 2 26989662 E-Mail: info@ctsystem.com

WAS-3005 Series

4 Ports 10/100/1000Base-T

and 1 Port 1000 Base-X Uplink Gigabit Ethernet

Switch with Extended

Operating Temperature

User’s Guide

Version 1.0

CTS WAS-3005 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual