CTS MCT-5002SFP+ User Manual

Trademarks

CTS is a registered trademark of Connection Technology
Systems Inc. Contents subject to revision without prior notice.

All other trademarks remain the property of their owners.

Copyright Statement

Copyright  Connection Technology Systems Inc.
This publication may not be reproduced as a whole or in part, in

any way whatsoever unless prior consent has been obtained
from Connection Technology Systems Inc.

FCC Warning

This equipment has been tested and found to comply with the
limits for a Class-A digital device, pursuant to Part 15 of the
FCC Rules. These standards are designed to provide
reasonable protection against harmful interference when these
devices are operated in a commercial environment. These
devices generate, use, and can radiate radio frequency energy
and may cause harmful interference to radio communications

unless installed in accordance with this User’s Guide.

Operation of these devices in a residential area is likely to
cause harmful interference which will make the user
responsible for the appropriate remedial action at his / her own
expense.

CE Mark Warning

These are Class A products. In a domestic environment these
products may cause radio interference in which case the user
will need to consider adequate preventative methods.

1. Checklist

The package should contain the following items:

-

One set of MCT-5002SFP+ Media Converter

-

1X AC-DC Power Adapter

-

This User’s Guide

Please notify your sales representative immediately if any
items are missing or damaged.

2. Overview

MCT-5002SFP+, a compact media converter, converts
traditional twisted-pair RJ-45 cable with 10G NBase-T
technology into a 10G SFP+ slot for pluggable fiber transceiver,
extending transmission distance for Data Center 10G NBase-T
to 10GBase-R conversion application or ISP Mobile DU (Dis­tributed Unit) and Enterprise broadband service applications.

MCT-5002SFP+ media converter is fully compliant with 802.3u,

802.3ab, 802.3z, 802.3bz, 802.3ae, and 802.3an standards.
Operation status can be locally monitored through a set of
Diagnostic LEDs located in the front panel.

Major Features:

-

Support Auto-Negotiation for 5-speed options (100M/
1G/2.5G/5G/10G) in TP port

-

Up to 10G at 100m over Cat.6A cable or better cabling, or

2.5G at 100m over Cat.5E or better cabling. (For more
details, please see Section 7.)

-

Support MDI/MDI-X Auto-Crossover

-

Support Link Alarm

-

Support Jumbo Frame 9K bytes (under 10Gbps)

-

Support the loopback mode in the fiber port

-

Support the fully-transparent mode

-

Support Auto & Force mode configuration for the TP port.

-

Fully compatible with CTS MCT-RACK-12/18-MGM chassis
for in-rack management

3. Installation

-

Attach the fiber cable from MCT-5002SFP+ to the fiber
network. The fiber connections must be matched – transmit
socket to receive socket.

-

Attach a UTP cable from the NBase-T network to the RJ-45
port on MCT-5002SFP+.

-

Connect the power adapter to the power jack on the rear
panel of MCT-5002SFP+ and check that if the Power LED
lights up. The TP and F/O LEDs will light up when all the
cable connections are satisfactory.

4. LED Description

LED

Color

Function

Power

Green

Lit when power is available.

TP

OFF

TP port link is down.

Green

Lit when TP 10Gbps port link is up.
Blinking when TP port is receiving and
transmitting data at the speed of 10Gbps.

Orange

Lit when TP port link less than 10Gbps is
up.
Blinking when TP port is receiving and
transmitting data at the speed of less than
10Gbps.

F/O
OFF

Fiber port link is down.

Green

Lit when Fiber 10Gbps port link is up.
Blinking when Fiber port is receiving and
transmitting data at the speed of 10Gbps.

FDX

OFF

TP works in the half-duplex mode.

Green

Lit when TP works in the full-duplex
mode.

Status

Green

Lit when the converter module is in
normal operation.

Orange

Lit when the system is booting up.
Slowly blinking when the firmware of the

converter module is not compatible with
CTS MCT-RACK-MGM chassis. The
converter module needs to be upgraded
with the new firmware.

Rapidly blinking when the converter
module works abnormally.

Orange

Green

Slowly blinking when the system is
upgrading the firmware.

Fig 2. Rear Panel of MCT-5002SFP+ Converter

CAUTION

To prevent suffering from burns due to the high
temperature, please wear a protective equipment
when you install or remove especially the converters.

RJ-45

Port

DIP

Switch

Fig 1. Side View of MCT-

5002SFP+ Converter

Fiber

Port

5. DIP SWITCH Setting

The default setting for PIN 1 through PIN 4 is OFF, and PIN5 is

ON.

Pin NO.

Function

OFF

ON

1

Fiber Auto­Negotiation

Disable

Enable

2

Link Alarm

Disable

Enable

3

Fiber Loopback
Mode

Disable

Enable

4

TP Port Speed

Auto-Speed

Fixed in
10Gbps

5

Software
Control

Configure
via software
of CTS
MCT-RACK

-MGM
chassis

Configure
via DIP
Switch

6

Reserved

N/A

N/A

NOTE:

1. Before adjusting the configuration of the Dip Switch, the

power should be unplugged.

2. PIN1, PIN 2, PIN 3 and PIN 4 work only when PIN 5 is set

to ON.

3. When the fiber loopback mode is enabled (PIN 3 is set to

ON), the media converter will loopback the received
packets (The packets are generated from the 3rd-party
device) to ensure the circuit quality, and TP port will be
forcibly stopped transmitting and receiving the packets.

6. Installing MCT-5002SFP+ on
MCT-RACK Chassis Series

Up to 6 sets of MCT-5002SFP+ installation can be supported
by CTS MCT-RACK-12/18 chassis series. For more details on
these installation, you may refer to our MCT-RACK-12/
18-MGM chassis HW User’s Guide.

For proper heat dissipation for MCT-RACK-18 chassis series,
please avoid using slot 1 as well as slot 18, and not to install
any modules next to the slot in which MCT-5002SFP+ is
installed to keep adequate ventilation.(See Fig. 3). As to MCT­RACK-12 chassis series, the staggered installation for your
MCT-5002SFP+ is highly recommended. (See Fig.4).

7. Transmission Distance Using
Copper Cables

*Please refer to the NBase-T specifications.

8. Technical Specifications

Standards:

802.3u, 802.3ab, 802.3z, 802.3bz,

802.3ae, and 802.3an

Interfaces:

1 x NBase-T (100M/1G/2.5G/5G/10G)
RJ-45 connector
1 X F/O port (SFP+)

LEDs:

Power, Status, FDX, Link/ACT of F/O, and
Link/ACT of TP

Power:

I/P AC 100-240V, 50/60Hz
O/P DC 12V/1.5A

Power
Consumption:

8W

Weight:

0.13Kg

Dimensions:

51mm(W)X74mm(D)X20mm(H)

Temperature:

Operating: 0o~50oC
Storage: -20o~60oC

Humidity:

5%~90% RH

Certification:

FCC/CE Class A

Media:

TP

EIA/TIA-568 CAT 5e, 1000M

Fiber

50/125um multi-mode fiber
9/125, 10/125um single-mode
fiber

*Please contact us for further reports and updates.

NOTE: Specifications may change without prior notice.

Contact Information

 Connection Technology Systems INC (CTS)

18F-6, No.79, Sec.1, Xintai 5th Rd., Xizhi Dist.,
New Taipei City 221, TAIWAN, R.O.C.
TEL: [phone] FAX: [phone]
E-Mail: [e-mail]

MCT-5002SFP+

100M/1G/2.5G/5G/10G

NBASE-T to 10GBASE-R

Standalone Media Converter

User’s Guide

Version 1.0

Fig 3. MCT-5002SFP+ Installation on

MCT-RACK-18 Chassis Series

Fig 4. MCT-5002SFP+ Installation on

MCT-RACK-12 Chassis Series