CTS CVT-3002-PLUSSERIES User Manual

Trademarks

CTS is a registered trademark of Connection Technology Systems Inc. Contents subject to revision without prior notice.

All other trademarks remain the property of their owners.

This publication may not be reproduced as a whole or in part, in any way whatsoever unless prior consent has been obtained from Connection Technology Systems Inc.

FCC Warning

The CVT-3002-PLUS Series converters have been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These standards are designed to provide reasonable protection against harmful interference when these devices are operated in a commercial environment. These devices generate, use, and can radiate radio frequency energy and may cause harmful interference to radio communications unless installed in accordance with this

User’s Guide. Operation of these devices in a residential area

is likely to cause harmful interference which will make the user responsible for the appropriate remedial action at his / her own expense.

CE Mark Warning

These are Class A products. In a domestic environment these products may cause radio interference in which case the user will need to consider adequate preventative methods.

1. Checklist

The package should contain the following items:

CVT-3002-PLUS Converter

AC-DC Power Adapter

User’s Guide

Please notify your sales representative immediately if any items are missing or damaged.

2. Overview

CVT-3002-PLUS is designed to meet the massive needs for Gigabit network deployment and able to extend a copper based Gigabit network via fiber cable to a maximum distance up to 80KM.

CVT-3002-PLUS is fully compliant with IEEE802.3, 802.3u,

802.3ab & 802.3z standards. It can be installed into a CVT Converter RACK. The installation & operation procedures are simple & straightforward. Operation status can be locally monitored through a set of Diagnostic LED located in the front panel.

Major Features:

Auto-Negotiation in TX port

MDI/MDIX Auto-Crossover supported

Support Flow Control

Support Link Alarm

Support Jumbo Frame 9K bytes (under 10,100,1000Mbps)

Store and Forward Switching Mechanism

Support Auto & Force mode configuration

3. Installation

Attach fiber cable from the CVT-3002-PLUS to the fiber network. The fiber connections must be matched – transmit socket to receive socket.

Attach a UTP cable from the 10/100/1000BASE-T network to the RJ-45 port on the CVT-3002-PLUS.

Connect the power adapter to the CVT-3002-PLUS and check that the Power LED lights up. The T X Link/Act and F/O Link/Act LEDs will light up when all the cable connections are satisfactory.

4. DIP SWITCH Setting

The default setting for PIN 1 and 6 is ON. The rest of Pins are OFF.

Pin NO.

Function

OFF

TP Auto-Negotiation

Disable

Enable

Manual TP speed

10M

100M

Manual TP speed

N/A

1000M

Duplex mode

Half

Full 5 Flow Control

Disable

Enable 6 F/O mode

Force

Auto 7 Link Alarm

Disable

Enable

Transmission

mode

Store and

forward

Pass-through

NOTE:

1. Before changing TP speed, duplex mode and flow control setting, please make sure PIN 1 is set to OFF.

2. When TP speed is set to 10M or 100M manually, PIN 3 needs to be turned OFF.

 3. Under 1000Mbps, it supports full-duplex mode only.

4. When Pin 8 is set to ON and the TP speed to 1000M, full-duplex mode and flow control are disabled.

Figure 3. CVT-3002-PLUS Converter Rear Panel

Figure 1. CVT-3002-PLUS dual fiber Front Panel

Figure 2. CVT-3002-PLUS WDM & SFP Front Panel

5. LED Description

6. Technical Specifications

Standards:

IEEE 802.3, 802.3u, 802.3ab,

802.3z

Interface:

1 X 10/100/1000 RJ-45 connector 1 X 1000 F/O port or SFP Slot

LED:

Power, FDX, Status, Speed, FO Link/ACT, TX Link/ACT

Power:

I/P AC 100-240V O/P DC 5V, 1.6A

Power Consumption:

Shipping Weight:

0.6KG

Dimensions:

71mm(W)X94mm(D)X26mm(H)

Temperature:

Operating: 0o~50oC Storage: -20o~60oC

Humidity:

5%~90% RH

Emission:

Electrical: UL, CSA EMI: FCC Class A, CE

*Please contact us for further reports and updates.

Media:

EIA/TIA-568 CAT 5e, 1000M

Fiber

50/125, 62.5/125um multi-mode fiber 9/125, 10/125um single-mode fiber

Fiber Transceiver Information

1000M

Multi-Mode

TYPE

BTFC

Connector Type

Wavelength

850nm

Typical Distance

500m

Min TX PWR

-9.5dBm

Max TX PWR

-4.0dBm

Sensitivity

-18.0dBm

Link Budget

8.5dB

Single-Mode

TYPE

BTFC(SM-10)

BTFC(SM-20)

BTFC(SM-30)

Connector Type

Wavelength

1310nm

Typical Distance

10Km

20Km

30Km

Min TX PWR

-9.5dBm

-5.0dBm

Max TX PWR

-3.0dBm

3.0dBm

Sensitivity

-20.0dBm

-24.0dBm

Link Budget

10.5dB

19.0dB

Wave-Length WDM

TYPE

W2A(SM-10)

W2B(SM-10)

W2A(SM-20)

W2B(SM-20)

Connector Type

TX Wavelength

1310nm

1550nm

1310nm

1550nm

RX Wavelength

1550nm

1310nm

1550nm

1310nm

Typical Distance

10 Km

20 Km

Min TX PWR

-10.0dBm

-9.0dBm

-7.0dBm

Max TX PWR

-3.0dBm

0dBm

Sensitivity

-22.0dBm

-23.0dBm

Link Budget

12.0 dB

13.0 dB

16.0 dB

NOTE: Specifications may change without prior notice.

Contact Information

Connection Technology Systems Inc 18F-6, No.79, Sec.1, Hsin Tai Wu Rd., Hsichih, Taipei Hsien, Taiwan, R.O.C. Tel + 886 2 2698 9661 Fax + 886 2 2698 9662 E-mail info@ctsystem.com



CVT-3002-PLUS

SERIES

10/100/1000BASE-T to

1000BASE-X Standalone

Media Converter

User’s Guide

Version 0.95

LED

Color

Function

Power

Green

Lit when power is available.

Link/Act

Green

Lit when TX cable connection with remote device is good. Blink when TX traffic is present.

Link/Act

Green

Lit when Fiber cable connection with remote device is good. Blink when F/O traffic is present.

FDX

Green

Lit when TX works in Full-Duplex. Not-Lit when TX works in Half-Duplex.

Speed

Green

No-Lit when TX works in 10M. Lit when TX works in 100M.

Orange

Lit when TX works in 1000M.

Status

Green

Lit when TX and F/O link is up.

Orange

Lit when TX or F/O link is down.

CTS CVT-3002-PLUSSERIES User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual