CTS CTS 3002SFP-DR Instructions

Trademarks

-

MCT-3002 Series Converter

-

AC-DC Power Adapter

-

User’s Guide

-

Auto-Negotiation in TP port

-

MDI/MDI-X Auto-Crossover supported

-

Support Link Alarm

-

Support Jumbo Frame 9K bytes (under 10,100,1000Mbps)

-

Store and Forward Switching Mechanism

-

Support Auto & Force mode configuration

-

Attach fiber cable from the MCT-3002 to the fiber network.
The fiber connections must be matched – transmit socket to
receive socket.

-

Attach a UTP cable from the 10/100/1000BASE-T network
to the RJ-45 port on the MCT-3002.

-

Connect the power adapter to the MCT-3002 and check
that the PWR/STA LED lights up. The TP and F/O LEDs will
light up when all the cable connections are satisfactory.

LED

Color

Function

PWR/STA

Green

Lit when power is available.

TP

Green

Lit when TP cable connection with
remote device is good.
Blink when TP traffic is present.

F/O

Green

Lit when Fiber cable connection at
100M with remote device is good.
Blink when F/O traffic is present.
(For dual rate model only)

Orange

Lit when Fiber cable connection at
1000M with remote device is good.
Blink when F/O traffic is present.

FDX

Green

Lit when TP works in Full-Duplex.
Not-Lit when TP works in Half-Duplex.

SPD

Green

Lit when TP works in 10M.
Lit when TP works in 100M.

Orange

Lit when TP works in 1000M.

2. Overview

CTS is a registered trademark of Connection Technology
Systems Inc. Contents subject to revision without prior notice.

All other trademarks remain the property of their owners.

Copyright Statement

Copyright  Connection Technology Systems Inc.
This publication may not be reproduced as a whole or in part, in

any way whatsoever unless prior consent has been obtained
from Connection Technology Systems Inc.

FCC Warning

This equipment has been tested and found to comply with the
limits for a Class-A digital device, pursuant to Part 15 of the
FCC Rules. These standards are designed to provide
reasonable protection against harmful interference when these
devices are operated in a commercial environment. These
devices generate, use, and can radiate radio frequency energy
and may cause harmful interference to radio communications

unless installed in accordance with this User’s Guide.

Operation of these devices in a residential area is likely to
cause harmful interference which will make the user
responsible for the appropriate remedial action at his / her own
expense.

CE Mark Warning

The MCT-3002 series media converter converts traditional
twisted-pair RJ-45 cable into various fiber media including
multi-mode, single-mode, SC connector, bi-directional WDM,
or a SFP slot for pluggable fiber transceiver, extending
transmission distance for the deployment to the household,
apartment or campus.

MCT-3002 series media converter is fully compliant with IEEE

802.3, 802.3u, 802.3ab & 802.3z standards.
Besides, it is equipped with some switching features including
store and forward. Operation status can be locally monitored
through a set of Diagnostic LED located in the front panel.

Major Features:

3. Installation

Figure 2. MCT-3002 WDM & SFP Front Panel

Figure 3. MCT-3002 Converter Rear Panel

Figure 4. MCT-3002 Converter Side Panel

4. LED Description

These are Class A products. In a domestic environment these
products may cause radio interference in which case the user
will need to consider adequate preventative methods.

1. Checklist

The package should contain the following items:

Please notify your sales representative immediately if any
items are missing or damaged.

Figure 1. MCT-3002 dual fiber Front Panel

5. DIP SWITCH Setting

Pin NO.

Function

OFF

ON

1

TP Auto-Negotiation

Disable

Enable

2

Manual TP speed

Please refer to

NOTE 3,4 and 5

3 4 Fiber Speed

Manual

Auto-Sensing

5

Fiber Manual Speed

100M

1000M 6 F/O mode

Force

Auto 7 N/A

N/A

N/A 8 Link Alarm

Disable

Enable

Standards:

IEEE 802.3, 802.3u, 802.3ab, 802.3z

Interface:

1 X RJ-45 connector
1 X F/O port or SFP Slot

LED:

Power/Status, FDX, Speed,
F/O, TP

Power:

I/P AC 100-240V
O/P DC 3.3V

Power
Consumption:

2.3W

Weight:

0.1Kg

Dimensions:

51mm(W)X74mm(D)X20mm(H)

Temperature:

Operating: 0o~50oC
Storage: -20o~60oC

Humidity:

5%~90% RH

Certification:

FCC/CE Class A

Media:

TP

EIA/TIA-568 CAT 5e, 1000M

Fiber

50/125, 62.5/125um multi-mode
fiber
9/125, 10/125um single-mode
fiber

TYPE

W2A(SM-10)

W2B(SM-10)

Connector Type

SC

SC

Wavelength

1310/1550nm

1550/1310nm

Typical Distance

10 Km

10 Km

Min TX PWR

-10.0dBm

-10.0dBm

Max TX PWR

-3.0dBm

-3.0dBm

Sensitivity

-20.0dBm

-20.0dBm

Link Budget

10.0dB

10.0dB

TYPE

BTFC

BTFC

(SM-10)

BTFC

(SM-20)

BTFC

(SM-30)

BTFC

(SM-50)

BTFC

(SM-80)

Connector

Type

SC

SC

SC

SC

SC

SC

Wavelength

850nm

1310nm

1310nm

1310nm

1550nm

1550nm

Typical

Distance

550m

10 Km

20 Km

30 Km

50 Km

80 Km

Min TX PWR

-9.5dBm

-9.5dBm

-5.0dBm

-5.0dBm

-5.0dBm

0dBm

Max TX

PWR

-4.0dBm

-3.0dBm

3.0dBm

3.0dBm

3.0dBm

5.0dBm

Sensitivity

-18.0dBm

-20.0dBm

-24.0dBm

-24.0dBm

-24.0dBm

-24.0dBm

Link Budget

8.5dB

10.5dB

19.0dB

19.0dB

19.0dB

24.0dB

TYPE

W2A

(SM-10)

W2B

(SM-10)

W2A

(SM-20)

W2B

(SM-20)

W2A

(SM-40)

W2B

(SM-40)

Connector

Type

SC

SC

SC

SC

SC

SC

TX

Wavelength

1310nm

1550nm

1310nm

1550nm

1310nm

1550nm

RX

Wavelength

1550nm

1310nm

1550nm

1310nm

1550nm

1310nm

Typical

Distance

10 Km

10 Km

20 Km

20 Km

40 Km

40 Km

Min TX

PWR

-10.0dBm

-9.0dBm

-7.0dBm

-7.0dBm

-3.0dBm

-3.0dBm

Max TX

PWR

-3.0dBm

-3.0dBm

0 dBm

0 dBm

2.0dBm

2.0dBm

Sensitivity

-22.0dBm

-22.0dBm

-23.0dBm

-23.0dBm

-22.0dBm

-22.0dBm

Link Budget

12.0dB

13.0dB

16.0dB

16.0dB

19.0dB

19.0dB

Fiber Transceiver Information

The default setting for PIN 1 through 7 is ON and PIN 8 is OFF.

NOTE:

1. Before adjusting the configuration of the Dip Switch, the
power should be unplugged.

2. Before changing the TP speed, please make sure PIN 1 is
set to OFF.

3. The TP speed is fixed in 10Mbps when PIN 2 & 3 are both
set to ON or OFF.

4. The TP speed is fixed in 100Mbps when PIN 2 is set to ON
and PIN 3 is set to OFF.

5. The TP speed is fixed in 1000Mbps when PIN 2 is set to
OFF and PIN 3 is set to ON.

6. Under 1000Mbps, it supports full-duplex mode only.

7. PIN 4 & 5 are for dual rate model (MCT-3002-DR) only.

8. Auto-Negotiation MUST be enabled (Pin 1 must be ON)
before enabling Link Alarm (Pin 8 is ON).

6. Technical Specifications

Dual Rate
2 Wave-Length WDM

1000M
Multi-Mode/Single-Mode

2 Wave-Length WDM

NOTE: Specifications may be changed without prior notice.

MCT-3002 SERIES

10/100/1000BASE-T to

1000BASE-X or

100/1000BASE-X

Standalone Media Converter

User’s Guide

Version 1.0

Contact Information

 Connection Technology Systems INC (CTS)

18F-6, No.79, Sec.1, Xintai 5th Rd., Xizhi Dist.,
New Taipei City 221, TAIWAN, R.O.C.
TEL: [phone] FAX: [phone]
E-Mail: [e-mail]