User Manual
dedicated LCD display solutions
Designed and manufactured by Austin Hughes
NAP-F21
Aluminum front bezel
OP-F21
Universal Mounting Open Frame
AP-F21
21.5” FHD LCD
Front NEMA4 / IP65
UM-UV-F21-Q112V1 www.rackmountsales.com
Legal Information
First English printing, October 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness
of the contents. The information in this document is subject to change without notice. We are not liable for any injury or
loss that results from the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for
future reference.
■ Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
■ Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
■ When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing dam
age to other equipment or injury to persons nearby.
■ When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the
power supply. Proper air convection is necessary to keep it from overheating.
■ Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
■ If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
■ Observe all precautions and warnings attached to the equipment.
■ If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being dam
aged by transient over-voltage.
■ Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fi re or electrical shock.
■ Only qualifi ed service personnel should open the chassis. Opening it yourself could damage the equipment and invali
date its warranty.
■ If any part of the equipment becomes damaged or stops functioning, have it checked by qualifi ed service personnel.
What the warranty does not cover
■ Any product, on which the serial number has been defaced, modifi ed or removed.
■ Damage, deterioration or malfunction resulting from:
□ Accident, misuse, neglect, fi re, water, lightning, or other acts of nature, unauthorized product modifi cation, or
failure to follow instructions supplied with the product.
□ Repair or attempted repair by anyone not authorized by us.
□ Any damage of the product due to shipment.
□ Removal or installation of the product.
□ Causes external to the product, such as electric power fl uctuation or failure.
□ Use of supplies or parts not meeting our specifi cations.
□ Normal wear and tear.
□ Any other causes which does not relate to a product defect.
■ Removal, installation, and set-up service charges.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifi cations made to this equipment may void the user’s authority to operate this equipment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
■ Re-position or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
UM-UV-F21-Q112V1 www.austin-hughes.com
< Part. 4 >
Options
4.1 Option Table
4.2 3G / HD / SD-SDI Broadcast-grade input
4.3 MCS Multi-display control solution
4.4 F21.5" Touchscreen : Resistive, Capacitive, Multi-touch
4.5 48V, 24V or 12VDC power
4.6 MIL-type or lockable connector
4.7 Quad display for CCTV
4.8 TV - PAL or NTSC
P.15
P.16
P.17 - 18
P.19 - 20
P.20
P.21
P.22
P.23 - 24
< Part. 3 >
Specifi cations / LCD OSD
3.1 Product Specifi cations
3.2 OSD for Basic Inputs ( VGA + DVI-D )
OSD for Upgrade Inputs ( VGA, DVI-D, HDMI, AV, Audio )
< Part. 1 >
AP-F21 / NAP-F21
1.1 Package Content
1.2 Structure Diagram & Dimension
1.3 Mounting Hardware & Installation
Contents
P. 1
P.2 - 3
P.4 - 5
< Part. 2 >
OP-F21
2.1 Package Content
2.2 Structure Diagram & Dimension
2.3 Mounting Hardware & Installation
P. 6
P.7 - 8
P.9
P.10 - 11
P.12
P.13 - 14
UM-UV-F21-Q112V1 www.austin-hughes.com
■ It is very important to mount the equipment in a suitable cabinet or on a stable surface.
■ Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in good condition. If anything is missing, or damaged, contact the supplier immediately.
Unpacking
Before Installation
How To Clean Your LCD Monitor
Caution :
■ To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.
■ When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your display. Pressure damage is not covered under warranty.
■ Use only cleansers made specifi cally for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens can scratch the LCD display or strip off the fi nish.
■ Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warranty.
■ Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood based
paper product such as paper towels can scratch your LCD screen.
Cleaning Your Monitor
To clean your LCD safely, please follow these steps :
Disconnect the power cord.
Gently wipe the surface using a clean, dry microfi ber cloth. Use as little pressure as possible.
1
2
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, please follow these steps :
Disconnect the power cord.
Spray a small amount of non-abrasive cleanser on a microfi ber cloth.
Gently wipe the surface. Use as little pressure as possible.
Wait until your monitor is completely dry before plugging it in and powering it up.
1
2
Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your
microfi ber cloth fi rst, not directly on the parts you are cleaning.
3
4
UM-UV-F21-Q112V1 www.austin-hughes.com
< 1.1 > Package Content - AP / NAP-F21
21.5" FHD LCD Display
P. 1
< Part 1 >
21.5" FHD LCD display X 1
6ft VGA cable X 1
Power adapter X 1
Power cord X 1
AP-F21 / NAP-F21
Mounting hardware X 1 pack
- Mounting bracket x 4 pcs
- M4* 6mm screw x 8 pcs
- M4* 50mm screw x 8 pcs
7
Rear case
LCD panel
Protective 3mm glass
6mm aluminum front bazel
Audio speaker, pair
LCD membrane
Remote sensor
1
2
3
4
5
6
7
Front view
1
2
3
4
Rear view
6
< 1.2 > Structure Diagram - AP / NAP-F21
AP-F21
NAP-F21
P. 2
5
Model
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
578 x 59 x 369 mm
22.7 x 2.3 x 14.5 inch
659 x 117 x 640 mm
25.9 x 4.6 x 25.2 inch
5 kg
11 lbs
10 kg
22 lbs
AP-F21
NAP-F21
VGADVI-DHDMI Audio
in - in - out
PC Video
S-Video RCAPower
Standard I/O : VGA and DVI-D
Options I/O : HDMI, Audio, S-Video + RCA with RC-2 remote controller
TV, USB for touchscreen
SDI or MCS ( either one )
< 1.2 > Dimension - AP / NAP-F21
P. 3
Front View Side View
Rear View
21.5” FHD LCD Display
AP-F21
NAP-F21
UNIT : mm
1mm = 0.03937 inch
Bottom View
UM-UV-F21-Q112V1 www.austin-hughes.com
< 1.3 > Panel Mount Installation - AP / NAP-F21
P. 4
1
x 4 pcs
Mounting
bracket
x 8 pcs
M4*6mm screw
2 3
x 8 pcs
M4*50mm screw
Hardware set part no. UV-BK#2
■ Install 4 mounting brackets with 8 x M4*6mm screws
■ Adjust the LCD panel with 8 x M4*50mm screws and fi x it on the surface.
Steps
UM-UV-F21-Q112V1 www.austin-hughes.com
< 1.3 > VESA mount Installation - AP / NAP-F21
M4 screw
P. 5
21.5” FHD LCD Display
■ Hardware and M4*4 pcs for VESA mount are not provided
VESA mount ( 100*100mm )
UM-UV-F21-Q112V1 www.austin-hughes.com
< 2.1 > Package Content - OP-F21
P. 6
< Part 2 >
21.5" FHD LCD display X 1
6ft VGA cable X 1
Power adapter X 1
Power cord X 1
OP-F21
VGADVI-DHDMI Audio
in - in - out
PC Video
S-Video RCAPower
Standard I/O : VGA and DVI-D
Options I/O : HDMI, Audio, S-Video + RCA with RC-2 remote controller
TV, USB for touchscreen
SDI or MCS ( either one )
< 2.2 > Structure Diagram - OP-F21
Front view
1
2
Rear view
5
4
3
21.5” FHD LCD Display
P. 7
Model
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
OP-F21
575 x 53 x 366 mm
22.6 x 2.1 x 14.4 inch
659 x 117 x 640 mm
25.9 x 4.6 x 25.2 inch
5 kg
11 lbs
10 kg
22 lbs
Rear case
LCD panel
Audio speaker, pair
Universal open frame mounting
LCD membrane
Extended remote sensor membrane cable
( 66cm from AD board to sensor end )
1
2
3
4
5
6
6
OP-F21
P. 8
Front View Side View
Rear View
< 2.2 > Dimension - OP-F21
OP-F21
UNIT : mm
1mm = 0.03937 inch
Bottom View
M4 screw
< 2.3 > Installation - OP-F21
21.5” FHD LCD Display
P. 9
( I ) Universal mount
( II ) VESA mount ( 100*100mm )
Hardware and M4*4 pcs for VESA mounting are not provided
Mechanical
Design
AP / NAP-F21 OP-F21
Front Panel Black, RAL 9005 -
Rear Casing Dark grey, RAL 7037 Dark grey, RAL 7037
VESA Mounting 100 x 100mm 100 x 100mm
Other Mounting Panel mount Universal mount
Protection 3mm protective glass
LCD
Panel
Manufacturer
Panel Size ( diagonal ) 21.5-inch Widescreen TFT color LCD
Display pixel ( dots x lines ) 1920 x 1080
Brightness ( typ. ) 250
Contrast Ratio ( typ. ) 1000:1
Color 16.7 M
Viewing Angle ( L/R/U/D ) 85/85/80/80
Response Time ( ms ) 5
Dot pitch ( mm ) 0.248
Display Area ( mm ) 476.64H x 268.11V
Surface treatment Haze 25%, Hard-coating
Surface hardness 3H
Backlight Type LED
MTBF ( hrs ) 30,000
Video
Connectivity
Digital HDMI HDMI 1.1, CEA-861-D
DVI DVI-D, TMDS single link
Analog
VGA Analog 0.7Vp-p
Composite ( RCA ) NTSC & PAL
S-Video ( 4-pin ) NTSC & PAL
Plug & Play DVI / VGA VESA EDID structure 1.3
Synchronization VGA Separate, Composite & SOG
Audio
Connectivity
Audio Input Connector 3.5mm stereo jack
Impedance / Power level 30kΩ / 750mV
Audio Output
Connector 3.5mm stereo jack
Resistance / Power level 30kΩ / 2.8V
Speaker Output Power 2 x 2W
*When the audio output is connected, speaker output is OFF
Power Power Supply
Range
Auto-sensing 100 to 240VAC,
50 / 60Hz
Power Consumption
Screen display ON 32W or less
Power saving mode 4W or less
Power button OFF 1W or less
< 3.1 > Product Specifi cations
P.10
< Part 3 >
Physical
Specifi cation
AP / NAP-F21 OP-F21
Product ( W x D x H )
578 x 59 x 369 mm 575 x 53 x 366 mm
22.7 x 2.3 x 14.5 inch 22.6 x 2.1 x 14.4 inch
Packing ( W x D x H )
659 x 117 x 640 mm 659 x 117 x 640 mm
25.9 x 4.6 x 25.2 inch 25.9 x 4.6 x 25.2 inch
Net Weight 5 kgs / 11 lbs 5 kgs / 11 lbs
Gross Weight 10 kgs / 22 lbs 10 kgs / 22 lbs
Applicable
Format
DVI-D / VGA Input PC Signal 1920 x 1080 x 60Hz
1280 x 1024 x 60 / 75Hz
1280 x 960 x 60Hz
1280 x 768 x 60 / 75Hz
1152 x 864 x 75Hz
1024 x 768 x 60 / 70 / 75Hz
848 x 480 x 60Hz
800 x 600 x 60 / 72 / 75Hz
720 x 400 x 70Hz
640 x 480 x 60 / 72 / 75Hz
640 x 400 x 70Hz
640 x 350 x 70Hz
HDMI Input
PC Signal Same as VGA
Video Signal
1080p : 50 / 60Hz
1080i : 50 / 60Hz
720p : 50 / 60Hz
480p : 60Hz
576p : 50Hz
Audio Signal 2ch Linear PCM ( 32 / 44.1 / 48 KHz )
Composite / S-Video
Input
NTSC 525 lines, 60 fi elds / sec
PAL 625 lines, 50 fi elds / sec
Environmental
Conditions
Operating Temperature 0 to 50°C degree
Humidity 20~90%, non-condensing
Storage
Temperature -5 to 60°C degree
Humidity 5~90%, non-condensing
Shock 10G acceleration (11ms duration)
Vibration 5~500Hz 1G RMS random
Regulatory Safety Approval FCC & CE
21.5” FHD LCD Display
P. 11
Exit the OSD screen
Toggle analog, digital & video connection (DVI-D and video options only)
Scrolls through menu options and adjusts the displayed control
(To auto adjustment by pressing the button for 5 seconds)
Display the OSD menu
Power on / off LCD
Power light
Green = On
Orange = Power saving
Membrane Switch Function
OSD Confi guration Page
Image:
for the brightness, contrast, color temp, red, green, and blue
Geometry:
for the auto adjust, H position, V position, phase and clock
Video:
for the colour, tint, sharpness, noise reduction, DCDi and TV Setup
Audio:
for volume, bass, treble, balance, AVL and mute
Misc:
for the language, OSD position, graphic mode, ratio, reset and timer
P.12
< 3.2 > OSD for Basic Inputs ( VGA + DVI-D, for AD board 2.1 )
UM-UV-F21-Q112V1 www.austin-hughes.com
P.13
< 3.2 > OSD for Upgrade Inputs
Picture
Picture mode : Standard / Vivid / Soft / User mode to choose
Brightness : Adjust background black level of the screen image
Contrast : Adjust the difference between the image background
(black level) and the foreground (white level)
Hue: Adjust the screen hue value
Saturation : Adjust the saturation of the image color
Picture size : Adjust the image size
Color temp : Standard / Cool / Warm / User to choose
Noise reduce : Reduce the noise of the image
Sharpness :
Adjust the image from weak to sharp
1
PC
Auto adjust : Automatically adjust sizes, centers and fi ne tunes the
video signal to eliminate waviness and distortion.
Clock : Adjust the clock value
Phase : Adjust the phase value
H. Position : Align the screen image left or right
V. Position : Align the screen image up or down
2
21.5” FHD LCD Display
Audio
Audio mode : Movie / Voice / Normal / Music mode to choose
Volume : Adjust the volume of sound
Bass :
Set the value of bass sound
Treble : Set the value of treble sound
Balance : Set the balance value of treble and bass sound
Analog TV audio : Set the value of analog TV audio sound
Mute : Turn off the surrounding sound
3
( VGA, DVI-D, HDMI, AV and Audio, for AD board 3.0 )
TV
Auto search : Automatically search
Manual search : Search the TV manual
Fine tune : Fine tune the TV signal
Color system : Adjust the TV color
Sound system : Adjust the TV sound
Channel edit : Edit the channel
4
MISC
Language : Select the language in which the OSD menu is
displayed - English
Sleep timer : Set the off time
PIP mode :
Adjust picture in picture setting
PIP position : Enter into PIP position
PIP source : Enter into the Sub source and sound source
System reset : Return the adjustment back to factory setting
Information : Select for Help
5
< 3.2 > OSD for Upgrade Inputs
( VGA, DVI-D, HDMI, AV and Audio, for AD board 3.0 )
P.14
( 1 ) The user can only select either SDI or MCS inputs.
( 2 ) For SDI or MCS input, the AD board will be upgraded to version 3.0, and this comes standard
with HDMI, DVI-D, VGA, S-Video, RCA , audio inputs and RC-2 remote controller.
***
For TV option , this comes with RC-2 remote controller.
*
< 4.1 > Option Table
Basic Options AP / NAP OP
SDI ***
HDMI
S-Video + RCA
Audio
Touchscreen
MCS multi-display control ***
DC Power
MIL-type / lockable connector
Quad display
TV *
21.5” FHD LCD Display
< Part 4 > Options
P.15
< 4.2 > Options : 3G / HD / SD-SDI input
P.16
INPUT 3G-SDI IN BNC x 1 / 0.8Vp-p ( 75 ohm )
3G-SDI OUT BNC x 1 / Active through, equalized & relocked
Standard Compliance Video SMPTE 425M / 274M / 296M / 125M
ITU-R BT.656
Audio SMPTE 299M / 272M-C
Compatible Audio Format 3G-SDI 48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
HD-SDI 48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized Video
SD-SDI 48kHz, 16 / 20 / 24 bit, 2 CH, Synchronized /
Asynchronized Video
Compatible Video Format 3G-SDI 1080p
1080p
1080i
720p
@60 / 50Hz, 4:2:2
@30 / 25 / 24Hz, 4:4:4
@60 / 50Hz, 4:4:4
@60 / 50Hz, 4:4:4
HD-SDI 1080p
1080i
720p
@30 / 25 / 24Hz, 4:2:2
@60 / 50Hz, 4:2:2
@60 / 50Hz, 4:2:2
SD-SDI 480i @60Hz, 4:2:2
ITU-R BT.656 576i @50Hz, 4:2:2
Max. Transmission Distance
75 ohm coaxial cable
3G-SDI 150m at 2.97Gb/s
HD-SDI 250m at 1.485Gb/s
SD-SDI 480m at 270Mb/s
Austin Hughes’ SDI input is an ideal solution for the broadcastgrade video and high resolution CCTV market.
Designed for use with UltraView Full HD 1080p and ultra high
resolution 1920 x 1200 LCD displays, Austin Hughes provides a
SDI input module without using additional space or power and it
comes standard with a 2-year warranty.
in - out
SDI
Audio
in - in - out
PC Video
VGA
DVI-DHDMI
S-VideoPower RCA
*** For SDI input, the AD board will be upgraded to version 3.0, and this comes standard with
HDMI, DVI-D, VGA, S-Video, RCA , audio inputs and RC-2 remote controller ( please refer to P.24 )
UM-UV-F21-Q112V1 www.austin-hughes.com
21.5” FHD LCD Display
< 4.3 > Options : MCS
LINK
OUT
IN OUT
RS-232C
Cat5 / 6 cable
max. 300 meters
up to 64 displays
Daisy chain up to 1,000
meters and 64 displays
RJ-45 jack
IN OUT IN OUT
Cat5 / 6 cable
max. 300 meters
Cat5 / 6 cable
max. 300 meters
15 feet serial cable
( over 15 feet, extender required )
Link
MCS
in out set
Audio
in - in - out
PC Video
VGA
DVI-DHDMI
S-VideoPower RCA
P.17
More control is always good. Especially when it is necessary and
easy. Austin Hughes provides MCS solution to control the OSD of
various UltraView LCD display up to 64 units.
The RS-232C is used for the communication between the PC and
the fi rst display via a 15 feet serial cable while the CAN bus is
used for the various LCD displays cascade together via CAT 5/6
cable, and daisy chain up to 1,000 meters.
Designed for use with UltraView LCD displays, Austin Hughes
provides a MCS input module without using additional space or
power and it comes standard with a 2-year warranty.
MCS
( Multi-display Control )
For the 1st and last display,
push the set switch downward
Set switch
For other daisy chain displays,
push the set switch upward
*** For MCS input, the AD board will be upgraded to version 3.0, and this comes standard with
HDMI, DVI-D, VGA, S-Video, RCA , audio inputs and RC-2 remote controller ( please refer to P.24 )
UM-UV-F21-Q112V1 www.austin-hughes.com
< 4.3 > Options : MCS
P.18
UM-UV-F21-Q112V1 www.austin-hughes.com
Step 1. Run the bundled CD disc or download the driver from the link below :
http://austin-hughes.com/downloads/index.php?opt=UVDL&n=sw
Step 2. Double click the Setup.exe
Step 3. Follow the installation instruction to fi nish the setup
Step 4. After installation, run the TouchKit program & the “4 point calibration”
Please follow the below steps to setup the touch screen:-
Please do the initial calibration
after the fi rst setup
21.5” FHD LCD Display
Audio
in - in - out
PC Video
VGA
DVI-DHDMI
S-VideoPower RCA
■ USB touchscreen package includes 1 x 6ft USB cable, quick reference guideline and CD disc
■ For detailed information, please refer to the attached CD disc
■ As the touchscreen unit is not made of toughened glass, please handle it carefully
USB Touchscreen
Model TRB e-Resistive
TCB e-Capacitive TMC2 Multi-touch
Technology
5-Wire Resistive Capacitive Projected Capacitive
Touch Point
Single Single Dual
Method
Stylus or Finger Finger Finger
Activation Force
≤ 50g / Stylus=R0.8 ≤ 50g ≤ 50g
Durability
10 million touches 300 million touches 100 million touches
Response Time
15 ms 20 ms 20 ms
Optical Transmittance
80% ± 3% 87% ±2% 90% ±2%
Surface Hardness
3H 9H 7H
Haze
8% ± 3% 7% 3%
Glass
3.2 ±0.2 mm 2.8 mm ±10% 2.4 ±0.15 mm
Connector
USB Type A USB Type A
Compatibility
Windows 7 / XP / Vista, Linux Windows 7
< 4.4 > Options : Touchscreen & driver
P.19
F21.5" USB Touchscreen Specifi cation
TRB & TCB Driver
UM-UV-F21-Q112V1 www.austin-hughes.com
< 4.4 > Options : Touchscreen & driver
< 4.5 > Options : DC Power
Model 12V 24V 48V
Input rating
Input voltage: 12-Volt 24-Volt 48-Volt
Input range: 9 ~ 18V 18 ~ 36V 36 ~ 75V
Input current
- No load 50 mA 50 mA 50 mA
- Full load 4950 mA 2450 mA 1220 mA
Output rating
Output voltage: 12-Volt 12-Volt 12-Volt
Output current: 4.16A 4.16A 4.16A
Effi ciency 84% 85% 85%
P.20
Connect the USB cable from the USB port on the LCD to a computer. The touch screen supports
easy Plug-and-Play operations. There is no need to install additional drivers on the computer.
TMC2 Driver
UM-UV-F21-Q112V1 www.austin-hughes.com
21.5” FHD LCD Display
Input Part no. MIL Standard
MIL - type
Connector
DC Power
***
( Male )
MS3470W8-33P MIL - DTL - 26482
VGA
***
( Male )
MS3470W14-15P MIL - DTL - 26482
Input Part no. Standard
Lockable
Connector
DC Power
( Male )
YM-Ext-461CP001 D-type 3W3
USB LUSB -
A111 - 00 -
< 4.6 > Options : MIL-type or Lockable Connector
*** There are several additional MIL DC and VGA connector types with varying design
characteristics to meet cost considerations and to provide users with the most
design fl exibility possible. For more information, please contact us.
*** MIL - type or Lockable connectors above can be integrated with our LCD displays.
Sale service just for connectors not provided.
P.21
UM-UV-F21-Q112V1 www.austin-hughes.com
< 4.7 > Options : Quad Display
QD Specifi cation
Item Description
Model Number QD (NTSC) QD (PAL)
Number of Color 16.7 M 16.7 M
Imaging System NTSC PAL
Resolution 1024 x 525 1024 x 625
Refresh Rate 60 50
Video Input
Camera Input
1.0 Vpp, 75 Ohm x 4
VCR Input
1.0 Vpp, 75 Ohm x 1
Video Output
Live Monitor
1.0 Vpp, 75 Ohm x 1
Loop Through Out
1.0 Vpp, 75 Ohm x 4
VCR Output
1.0 Vpp, 75 Ohm x 1
Auto Gain Control Yes
Time / Date Yes
On Screen Display Yes
Camera Title 8 Character Title
Display Format
2 x Zoom On
Playback
Yes
QUAD Yes
FULL
Yes
SEQUENCY
Yes
Dwell Time 0 to 99 Sec Adjustable
Alarm Inputs Selectable NO/NC Contacts x 4
Relay Outputs NO/NC contacts x 1: 1A @DC24V Max.
Alarm Hold Time 1 Sec to Non-stop
Built-in Buzzer Yes
Key Lock Yes
P.22
*** For QD option, the casing dimensions will be changed.
UM-UV-F21-Q112V1 www.austin-hughes.com
( 1 ) For TV option, the AD board will be upgraded to version 3.0, and this comes standard with
HDMI, DVI-D, VGA, S-Video, RCA , audio inputs and RC-2 remote controller.
( 2 ) For TV option, casing dimensions will be changed.
***
21.5” FHD LCD Display
TV
Audio
in - in - out
PC Video
VGA
DVI-DHDMI
S-VideoPower RCA
< 4.8 > Options : TV ( Analog )
P.23
UM-UV-F21-Q112V1 www.austin-hughes.com
21.5” FHD LCD Display
How to Use RC-2 Remote Controller
P.24
1
2
3
4
5
6
AUTO
0
-/--
7
8 9
PIP
MENU SELECT
BACK
EXIT
SOURCE
POSITION
SWAP
PIP
AUDIO
ASPECT
SLEEP
PIP
ENTER
CH
FREEZE
MUTEINPUT
VOL
W
a
t
e
r
p
r
o
o
f
1
4
3
2
5
7
6
20
21
8
9
10
11
12
13
15
16
17
18
19
14
INPUT Select the source
Switches on or off the TV
0 - 9
Only use in TV mode. Select channels. For channel numbers 10
and above, enter the second digit within two seconds.
AUTO Auto adjust
MENU Display the menu on the screen or go to the previous menu
▲ / ▼ / ◄ / ► / ENTER
Go to the upper menu or select the previous value /
Go to the next menu or select the next value /
Decrease the setting value /
Increase the setting value or enter to the select item setting
Enter to the select item settings or excude the setting
BACK Back to previous value
MUTE Turn on or off the speaker
Vol + / - Increase or decrease the speaker volume
CH + / - For TV model only, increase or decrease the channel number
FREEZE Reserve for OEM model
- / -- For setting input single or double digits
ASPECT Adjust the screen size
SELECT To select the existing item
SLEEP Select the sleeping time
EXIT Exit the menu or cancel
PIP functions
PIP
Picture in picture
PIP AUDIO To set the audio of in PIP mode
POSITION To set the screen position in PIP mode
SOURCE PIP Source
SWAP Swap screen in PIP mode
1
8
2
3
4
5
6
7
9
10
11
12
13
14
15
16
17
18
19
20
21
Loading...