INSTRUCTIONS OF INSTALLATION, OPERATION
& MAINTENANCE
CRIF600
MODEL CRIF600
2
1. INTRODUCTION
Proper installation and maintenance are essential for best use of your appliance. It is therefore necessary to
carefully read the instructions of this manual.
2. TRANSPORT (Figure 1)
3. INSTALLATION OF THE APPLIANCE
• Unpack the appliance. In order to remove it from the pallet use a screwdriver and unscrew the 4 screws (Fig. 2).
• Make sure that the appliance is stable and in horizontal position.
• Perfectly level the appliance by adjusting the adjustable stands that are provided with the appliance.
• Never install the freezer in a room exposed to direct sun radiation nor in the vicinity of a heat source such as
cooker, stove, heater, fireplace etc.
• Avoid installing the appliance in confined rooms, in rooms with dampness without airing or in wall recesses.
• The clearance behind the appliance must be at least 10 cm distance from the wall or other voluminous objects. This
clearance is the minimum required to ensure normal ventilation of the refrigeration mechanism. You will find one
spacer with two fixing screws within the appliance, which obtains the airing space of 10 cm after fitting it at the
back of the freezer (Fig. 3A).
• Inside your appliance, you will find:
1. Inox door handle and two inox screws inside a plastic bag.
2. Offset handle and two stabilization screws inside a transparent bag.
3. Shelves for products placement.
4. Four hooks per each shelf for its proper stabilization. (see figure 3).
5. One pair of keys for the lock (see figure 1a).
4. ELECTRICAL CONNECTION
Figure 1a
Make sure that the feed cable and the socket are appropriate for the appliance’s power. In case of doubt, contact a
qualified technician.
Before inserting the plug in the mains outlet, make sure the voltage mentioned on the nameplate inside the appliance
(on the top right) compiles with the one of your network. A discrepancy of +/- 10% is acceptable.
Too high or too low voltage network may seriously damage the compressor. Such damages are not covered by the
guarantee. The appliance must be earthed as prescribed by the relevant legislation whereas it is indispensable for your
personal safety. The manufacturer has provided for earthing in the electrical installation and external surface of the
appliance.
NOTE: Upon start up, running may be noisy. Noise will only last for the engine “running in” time and will
decrease progressively.
5. SHELVES (Figure 3).
Place the shelves upon the hooks carefully so that the two
fitted wires of each shelf to be placed at the cabinet’s back (Fig 3).
That way, the proper airflow at the cabinet’s back is ensured.
Figure 1
Always transport the appliance in vertical position, do not
overturn it and do not load it in leaning position.
SCREW
SCREW
SCREW
Figure 2
Β
Α
Figure 3
3
6. OPERATION
Once the appliance is installed, wait for at least 30 minutes before start – up. Afterwards, plug in the appliance.
The thermostat and the operation switch “O/I” are located behind the fitted metallic grill panel. In order to operate the
appliance, the operation switch must be on.
Start up the appliance with no load and make sure the door is properly closed.
Wait for at least two hours in order to achieve the required temperature inside the freezer. Then, place the products.
The compressor will not restart immediately, in case of starting up the appliance straight after terminating its operation –
either via the thermostat or due to power failure –. This is normal. The compressor will automatically start soon after.
For your appliance’s protection, always wait for fifteen minutes before each restart.
Do not use any electrical devices inside the storage places for appliance’s foods.
Keep the air openings in the cover without any obstacle.
This appliance is not to be used by individuals (and kids also) with low physical or mental abilities or lack of
experience and knowledge but only if they are supervised or specific orders were given by someone who is responsible
for their safety.
The kids should be supervised in order to avoid playing with the appliance.
7. PRODUCTS LOADING (Figure 4)
8. ELECTRICAL THERMOSTAT - THERMOMETER (Figure 5)
Place the products on the shelves without blocking the proper
airflow inside the cabinet (Fig. 4). Do not place products at the top
shelf, which would block the airflow exit due to their height, from the
fan to the cabinet top. The distance of 10 cm among the products and
the fan is necessary.
The thermostat is located behind the fitted metallic canopy at
the top of the freezer. Our company sets it so that your appliance
could be able to maintain your products to an average temperature
from -24 to -18
ο
C according to its climate class (40 οC temperature
and 40% relative humidity of the environment).
If you wish, you can change the temperature average inside
the cabinet by programming the electrical thermostat-thermometer
properly.
The necessary commands are given below.
1
Í
1
Í
Figure 4
Figure 5
Loading...