Crye Precision ASR Operator's Manual

ASR™ LANYARD

OPERATOR’S MANUAL

BLC-092

This manual must be carefully read by all persons who have or will have

the

responsibility for using or maintaining this product.

Any warranties made by Crye Precision LLC with respect to this product are voided if the

product is not used and maintained in accordance with the instructions in this

manual.

For any questions relative to the use or repair of this product, please write Crye Precision
LLC or call 1-718-246-3838 during regular business hours.

The following are safety warnings intended to call attention to fundamental performance
limitations and areas of the product where proper usage must be followed. Failure to use and maintain
the product according to the warnings contained herein may result in the product failing to
perform as designed, and/or the persons relying on this product sustaining serious personal injury
and/or death.

•

Refer to the product label and manual for

load rating and use guidelines.

• The safety belt worn in conjunction with the
lanyard is intended only to prevent the user from
reaching a position where a fall can occur.

• The Crye Precision LRB must be worn in
conjunction with the Crye Precision LRB Leg
Loops for mountaineering, rappelling, and fall
arrest.

• The Crye Precision LRB Leg Loops must be worn
in conjunction with the Crye Precision LRB.

• Avoid repeated exposure of fall-protection
devices to salt water, solvents, or chemicals. See
care instructions.

• Fall-protection devices that show no signs of
damage must be replaced 5 years from date of
purchase.

• This fall-protection device is not flame resistant.

• Perform periodic inspections of the hardware,
webbing, and stitching of the fall-protection
device. Discontinue use of damaged fall­protection devices immediately.

• DO NOT machine wash or dry clean the
product. Exposure to detergents, bleach, or
solvents may result in degradation and reduce
the effectiveness of the product.

• Inspect the product for discoloration, cuts,
tears, abrasions or cracks before and after each
use.

• DO NOT alter the product in any way.

• DO NOT expose the product to open flame or
excessive heat.

• All replacement parts must

be acquired from

Crye Precision LLC or a licensed distributor.

• The most current version of this manual may be
found at www.cryeprecision.com.

• DO NOT use this product except in its intended
manner.

EQUIPMENT INFORMATION

INTRODUCTION ............................................................... 1

INCLUDED COMPONENTS ................................................ 2

CONFIGURING THE ASR

™

LANYARD

PROPER ATTACHMENTS

................................................................. 5

ASR

™

ADJUSTMENT ...................................................................... 6

RELEASING FROM LRB

™

................................................. 7

STOWING SAFETY RELEASE PULL .................................... 8

CARE INSTRUCTIONS

...................................................................... 11

CONTENTS

1 ASR™ LANYARD

INTRODUCTION

The Crye Precision ASR™ (ADJUSTABLE SAFETY RESTRAINT) Lanyard is designed to be

used in conjunction with the

LRB™ as a travel restraint during helicopter operations.

The

ASR™ LANYARD is designed to be quickly and easily adjusted from 18” to 30”.

There are numerous features incorporated into both the

LRB™ and ASR™ LANYARD

that are based on user needs and feedback from various SOF groups. The main

features are:

FEATURES

�

Ofcially approved for use by USSOCOM

�

Carabiner with single-hand operation

�

Emergency release from belt under tension

�

Length adjustable from 18-30 inches

�

Adjuster hardware will not slip under load

�

Quickly and easily adjusted while being worn

�

Sleeve covers critical stitching for durability

�

Meets or exceeds USSOCOM safety lanyard specications

�

Made in the US from US materials

2EQUIPMENT INFORMATION

INCLUDED COMPONENTS

ASR LANYARD

CONFIGURING THE ASR™ LANYARD

5 ASR™ LANYARD

PROPER ATTACHMENTS

Ensure the quick release hardware is properly seated and secured

to the

LRB™ attachment point.

Ensure the quick release hardware is properly seated and secured

to the

LRB™ FLOATING LOOP attachment point.

To attach to

LRB™, perform the following:

To attach to

LRB™ FLOATING LOOP, perform the following:

6CONFIGURING THE ASR LANYARD

ASR™ LANYARD ADJUSTMENT

1

To shorten the ASR

™

LANYARD, pull the free running end away

from the body—excess webbing can be stowed under the elastic

retainers.

2

To elongate the ASR

™

LANYARD, use thumb to pull back on the

adjustment buckle and pull carabiner away from the body.

7 ASR™ LANYARD

RELEASE FROM LRB™

2

1

Grasp the safety release pull tab and pull it out from the stowage

retainer. Pull safety release pull tab away from the hardware

attachment point to release the snap shackle from the

LRB™.

Loop nger or thumb under the safety release pull tab.

8

STOWING SAFETY RELEASE PULL

2

1

Fold the safety release tab so that the VELCRO® holds the fold

secure, then insert back into the retainer.

Stow the safety release pull tab into the retainer.

CONFIGURING THE ASR LANYARD

CARE INSTRUCTIONS

11 ASR™ LANYARD

CARE INSTRUCTIONS

Care instructions must be read prior to each use.

�

You can hand wash your ASR

™

LANYARD with mild soap and warm water. Never use bleach as that can degrade the materials.

Allow to air dry away from direct sunlight. Do not store damp.

12CARE INSTRUCTIONS

DO NOT

�

Machine wash or dry clean.

�

Apply iron or any heat to the ASR

™

LANYARD.

�

Expose your ASR

™

LANYARD to open ame or excessive heat.

�

Attempt to modify or repair the ASR

™

LANYARD in any way.

13 ASR™ LANYARD

NOTES

14NOTES

ABOUT US

Crye Precision designs and manufactures

truly innovative equipment for America’s

ghting forces. We are proud and honored

to serve our customers' needs. We spend

as much time as we can with users,

continuously incorporating their experience

and feedback into the gear. We give them

our full support and are indebted to them

for their service and their sacrice. We make

uncompromising gear for uncompromising

individuals. We work hard to provide smart,

high-performance, long-wearing gear for

people who demand the best. We make

all of our gear in America from American

materials. Every item is designed to help

you perform better.

WARRANTY

If a defect in materials or workmanship is

found in any of our products, we will repair

or replace it, free of charge, for the lifetime

of the product. This excludes normal wear

and tear. Be aware that the customer is

responsible for any and all return shipping

charges. This applies to the original purchaser

and is nontransferable.

BODY ARMOR

It is against Federal Law for a person

convicted of a violent felony to purchase

or possess body armor. In addition, various

states also have laws restricting the purchase

or possession of body armor by persons

convicted of certain felonies, other crimes

of violence, or drug crimes. By purchasing

body armor, you acknowledge and certify

that (i) you have no felony convictions, (ii)

you have not been convicted of any other

crime that would restrict your ability to

purchase or possess body armor under any

Federal or State law, (iii) you do not intend

to use the body armor for any criminal

purpose and (iv) you are over 18 years old.

Crye Precision reserves the right, in its sole

discretion, to refuse to sell body armor to any

person. Additionally, the sale of body armor

to residents of Connecticut is restricted to

in-person sales, unless the sale is made to

certain law enforcement or military personnel.

We require that all orders of body armor be

accompanied by a government issued photo

identication.

CONTACT INFO

Crye Precision LLC

Brooklyn Navy Yard

63 Flushing Ave Unit 252

Building 128B

Brooklyn, NY 11205

Phone: [phone]

Fax: [phone]

[e-mail]

www.cryeprecision.com

COPYRIGHT

© 2019 Crye Precision LLC. The ‘CP’ logo

are trademarks of Crye Precision LLC.

REV 092217