Crydom Series 1T 120 VAC Data Sheet

Download

Page 1

Series 1T 120 VAC

Panel Mount

Datasheet

• Ratings from 10A to 40A @ 24-140 VAC

• SCR output for heavy industrial loads

• Zero voltage or instantaneous turn-on outputs

• UL/CSA/VDE Approved, CE Compliant to EN60950-1

• AC or DC control

• Direct bond copper substrate

• Direct power lead frame

• Epoxy free design

• Improved SEMS screw and washer

• Redesigned housing with anti-rotation barriers

For Generation 3 datasheet click here

PRODUCT SELECTION

3-32 VDC D1210T D1225T D1240T 90-280 VAC A1210T A1225T A1240T 18-36 VAC A1210ET A1225ET A1240ET

40A25A10AControl Voltage

AVAILABLE OPTIONS

Control Voltage A: 90-280 VAC D: 3-32 VDC AxxxxE: 18-36 VAC

Operating Voltage 12: 24-140 VAC

OUTPUT SPECIFICATIONS

Operating Voltage Range (47-63Hz) [Vrms] 24-140 VAC 24-140 VAC 24-140 VAC Transient Overvoltage [Vpk] 600 600 600 Maximum Off-State Leakage Current @ Rated Voltage [mArms] 8 8 8 Minimum Off-State dv/dt @ Maximum Rated Voltage [V/µsec] 500 500 500 Maximum Load Current [Arms] (2)(6) 10 25 40 Minimum Load Current [mArms] 40 40 40 Maximum 1 Cycle Surge Current (50/60 Hz) [Apk] 115/120 239/250 597/625 Maximum I²t for Fusing (50/60Hz) [A² sec] 66/60 285/259 1770/1629 Maximum On-State Voltage Drop @ Rated Current [Vrms] (7) 1.15 1.15 1.15 Thermal Resistance Junction to Case (Rjc) [°C/W] 1.03 0.8 0.5 Minimum Power Factor (at Maximum Load) 0.5 0.5 0.5

Rated Load Current 10: 10 Amps 25: 25 Amps 40: 40 Amps

(5)

EA P G

Termination Blank: Screw F: Quick Connect

(Up to 50 Amps only)

K: Hex standoffs

Overvoltage Protection Blank: Not Included P: Included

(3)

(1)

(2)

Input Status LED Blank: Not Included G: Included

Thermal Pad Blank: Not Included H: Included

Trigger Circuit T: Phototransistor

(Not needed with -B suffix, included as standard)

Required for valid part number For options only and not required for valid part number

Not all part number combinations are available. Contact Crydom Technical support for information on the availability of a specific part number.

Switching Type Blank: Zero Voltage Turn-On

-10: Instantaneous Turn-On

-10T

-B

Output Type

-B: Normally Closed

(Not available with

-10 option)

40A25A10ADescription

(4)

INPUT SPECIFICATIONS

(5)

A12xxETA12xxTD12xxTDescription

Control Voltage Range 3-32 VDC 90-280 Vrms 18-36 Vrms Minimum Turn-On Voltage (8) 3.0 VDC Must Turn-Off Voltage (10) 1 VDC 10 Vrms 4 Vrms Minimum Input Current for on-state [mA] 3.4 2 2 Maximum Input Current for on-state [mA] 24 4.9 4 Nominal Input Impedance [Ohms] 1.5K 60K 9K Maximum Turn-on Time [msec] 1/2 Cycle Maximum Turn-off Time [msec] 1/2 Cycle 40 40

(9)

(11)

90 Vrms 18 Vrms

10 10

Page 2

Panel Mount

Datasheet

GENERAL SPECIFICATIONS

(5)

ParametersDescription

Dielectric Strength, Input/Output/Base (50/60Hz) 4000 Vrms Minimum Insulation Resistance (@ 500 VDC)

109 Ohm

Maximum Capacitance, Input/Output 8 pF Ambient Operating Temperature Range -40 to 80 °C Ambient Storage Temperature Range -40 to 125 °C Weight (typical) 2.64 oz (74.9 gr) Housing Material UL 94 V-0 Baseplate Material Aluminum Input Terminal Screw Torque Range [in-lb/Nm] 13-15 / 1.5-1.7 Output Terminal Screw Torque Range [in lb/Nm] 18-20 (2-2.2) SSR Mounting Screw Torque Range [in-lb/Nm] 18-20 / 2.0-2.2

Input/Load Terminal Screw Torque Range (in-lb/Nm) (2) w/”K” option 8-10 / 0.9-1.13

Input/Output Terminal Screw Thread Size #6-32 UNC / #8-32 UNC Humidity per IEC60068-2-78 93% Non condensing LED Input Status Indicator w/”G” option (green)

MTBF (Mean Time Between Failures) at 40°C ambient temperature (12) MTBF (Mean Time Between Failures) at 60°C ambient temperature (12)

11,641,553 hours (1,328 years)

7,210,376 hours (823 years)

WIRING DIAGRAM

Load

1 ( ) 2 ( )

OUTPUT

SOLI D S T AT E R ELA Y

INPUT

4 (– / ) 3 (+ / )

(13)

Terminals

Input

Output

Recommended Wire Sizes

Wire Size

(Solid / Stranded)

24 AWG (0.2 mm

2 x 12 AWG (3.3 mm

20 AWG (0.5 mm

2 x 10 AWG (5.3 mm

2 x 8 AWG (8.4 mm

) / 0.2 [minimum]

) / 0.518 [minimum]

) / 8.4 [maximum]

) / 3.3 [maximum]

) / 5.3

Wire Pull-Out

Strength (lb)[N]

10 [44.5]

90 [400]

30 [133]

110 [490]

90 [400]

Input Current (mA)

“T” Option - Low Voltage Output

0 5 10 15 20 25 30

Input Current vs Input Voltage

DC Input Voltage

EQUIVALENT CIRCUIT BLOCK DIAGRAMS

Diagram: A12xxT, A12xxET Diagram: D12xxT

AC/DC

+DC

Converter

(14)

Trigger Circuit

(15)

+DC

Trigger

(14)

Circuit

(15)

Page 3

Panel Mount

Datasheet

MECHANICAL SPECIFICATIONS

Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters]

(5)

Screw Termination

1.1

1.88

[47.6]

[27.9]

0.49

[12.4]

OUTPUT

S OLID S T A T E R ELA Y

INPUT

1.0

[25.4]

1.75

[44.5]

Mounting Hole/Slot

0.19 [4.9] DIA.

1.7

[43.2]

Quick Connect Termination (“F” Option) - Up to 25 Amp (1)

Mounting Hole/Slot

0.19 [4.9] DIA.

1.58

[40.2]

0.49

[12.4]

Faston Terminal(16)

0.25 x 0.032

(2 places)

1.31

[33.4]

0.89

[22.6]

2.25

[57.3]

Hex Standoff Termination (“K” Option)

1.88

[47.6]

1.1

[27.9]

0.49

[12.4]

OUTPUT

S OLID S T A T E R ELA Y

INPUT

1.0

[25.4]

1.75

[44.5]

Mounting Hole/Slot

0.19 [4.9] DIA.

1.70

[43.2]

(4 places)

(2 places)

Quick Connect Termination (“F” Option) - Up to 50 Amp (1)

Faston Terminal(16)

0.25 x 0.032

(4 places)

0.45

[11.4]

(2 places)

Mounting Hole/Slot

0.19 [4.9] DIA.

1.58

[40.2]

0.63

[16.0]

(2)

1.04

[26.4]

2.25

[57.3]

0.93

[23.6]

1.0

[25.4]

1.31

[33.4]

1.7

[43.2]

Faston Terminal(16)

0.187 x 0.020

(2 places)

1.25

[31.8]

2.25

[57.3]

1.88

[47.6]

OUTPUT

S OLID S T A T E R ELA Y

INPUT

0.49

[12.4]

1.40

[35.6]

1.75

[44.5]

Faston Terminal(16)

1.7

[43.2]

0.187 x 0.020

(2 places)

1.25

[31.8]

1.88

[47.6]

OUTPUT

S OLID S T A T E R ELA Y

INPUT

1.40

[35.6]

1.75

[44.5]

GENERAL NOTES

(1) Single pair (up to 25A) Double pair* (up to 50A). *Caution: User must connect both pairs. (2)

Option “K” is designed and tested for use with printed circuit boards or ring/fork terminals having a thickness between 0.031 and 0.093 inches (0.79 to 2.36 mm), and loads rated up to 50

Amps. For higher load currents, the “K” standoff temperature must not exceed 105°C. For additional application assistance please contact Crydom Technical Support.

(3) Output will self trigger between 450-600Vpk, Min., not suitable for capacitive loads. (4) Instantaneous turn-on version is not recomended for capacitive loads. Use zero turn-on only. (5) All parameters at 25°C unless otherwise speciﬁed. (6) Heat sinking required, see derating curves. (7)

For 40mA minimum current, the voltage drop increases over maximum rated.

(8)

Maximum turn-on voltage for -B option is: 1VDC for DC control, 10Vrms for AC control, and 4Vrms for E control range.

(9)

For relays with option “G” minimum control voltage is 4.5VDC.

(10)

Must turn-off voltage for -B option is: 3VDC for DC control, 90Vrms for AC control, and 18Vrms for E control range.

(11) T

urn-on time for Instantaneous turn-on versions is 0.02 msec (DC Control Models).

(12)

All parameters at 50% power rating and 100% duty cycle (contact Crydom tech support for detailed report).

(13) Load can be wired to either SSR output terminal 1 or 2. (14) Elective Input Status LED, “G” option. (15) Elective Overvoltage Protection, “P” option.

(16)

Mechanical dimensions vary from G3 models.

2.25

[57.3]

For additional information or speciﬁc questions, contact Crydom Technical Support.

Page 4

SURGE CURRENT INFORMATION

Panel Mount

Datasheet

120

10 A

100

Surge Current (Amp)

0.01 0.1 1 10

Surge Duration (Secs)

Non repetitive peak surge current at Tj initial 40ºC.

250

200

150

100

Surge Current (Amp)

0.01 0.1 1 10

40 A

600

500

400

300

200

100

Surge Current (Amp)

0.01 0.1 1 10

Surge Duration (Secs)

25 A

Surge Duration (Secs)

THERMAL DERATE INFORMATION

10 A

3ºC/W

Load Current (Amps)

20 30 40 50 60 70 80

Ambient Temperature (ºC)

5ºC/W

No Heatsink

Load Current (Amps)

40 A

1ºC/W

20 30 40 50 60 70 80

1.5ºC/W

Ambient Temperature (ºC)

2ºC/W

3.5ºC/W

25 A

1.5ºC/W

20 30 40 50 60 70 80

Ambient Temperature (ºC)

2ºC/W

3ºC/W

Page 5

AGENCY APPROVALS

EN60950 : Meets the requirements of sections1.5: 1,7: 2.9: 2.10.5.3: 4.2: 4.5: 4.7: Designed in accordance with the requirements of IEC 62314 IEC 61000-4-2 : Electrostatic Discharge – Level 3 IEC 61000-4-4 : Electrically Fast Transients – Level 3 IEC 61000-4-5 : Electrical Surges – Level 3 IEC 60068-2-6 : Vibration 0.33mm and 0.75 mm Amplitude over 10-55 Hz IEC 60068-2-27 : Shock Resistance 15g/11ms

E116949 LR81689 10143 UG (Not Applicable: -B and 4D)

ACCESORIES

Panel Mount

Datasheet

New Accessories!

Protective Cover & Hardware Kits

Protective Cover

Part number: KS101

Clear plastic cover compatible with all new S1 designs. Safety covers provide added protection from electric shock when installing or checking equipment.

Hardware Kit

Part number: HK4

Bag with 2 square brass accessories and 2 screw 8-32 x 5/8 for output. Used to mount TMR1 lug terminals.

Cover Hardware

Kit

KS101 HK1

HK4

Recommended Accessories

Heat Sink

Part No.

HS501DR

HS301 / HS301DR

HS251

HS202 / HS202DR

HS201 / HS201DR

HS172

HS151 / HS151DR

HS122 / HS122DR

HS103 / HS103DR

HS101

HS073

HS072

HS053

HS033

HS023

Thermal Resistance

[ºC/W]

5.0

3.0

2.5

2.0

1.7

1.5

1.2

1.0

0.7

0.5

0.36

0.25

Lug Terminal Thermal Pad

TRM1

TRM6

HSP-1

HSP-2

Rev. 061716

Page 6

Panel Mount

Datasheet

DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH.

• Disconnect all power before installing or working with this equipment.

• Verify all connections and replace all covers before turning on power.

Failure to follow these instructions will result in death or serious injury.

RIESGO DE DESCARGA ELECTRICA O EXPLOSION.

• Desconectar todos los suministros de energia a este equipo antes de trabajar

con este equipo.

• Verificar todas las

conexiones y colocar todas las

tapas antes de energizer el equipo.

El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias.

RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION

• Eteindre toutes les sources d'énergie de cet appareil avant de travailler dessus de cet appareil

• Vérifier tous

connections, et

remettre tous couverts en olace avant de

mettre sous

De non-suivi de ces instructions provoquera la mort ou des lésions sérieuses sérieuses.

GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION.

• Stellen Sie jeglichen St

rom ab, der dieses Gerät versorgt, bevor

Sie an dem

Gerät Arbeiten durchführen

• Vor dem Drehen auf Energie alle Anschlüsse überprüfen und alle Abdeckungen ersetzen.

Unterlassung dieser Anweisungen können zum Tode oder zu schweren Verletzungen führen.

RISCHIO DI SCOSSA ELETTRICA O DELL’ESPLOSIONE.

• Spenga tutta l'alimentazione che fornisce questa apparecchiatura prima di lavorare a questa

apparecchiatura

• Verificare tutti i collegamenti e sostituire

utte le coperture

t prima dell’accensione

L'omissione di queste istruzioni provocherà la morte o lesioni serie

存在电击、爆炸或电弧闪烁危险

•

在操作此设备之前请先关闭电源。

若不遵守这些说明，可能会导致严重的人身伤害甚至死亡。

WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告

RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE

• The product's side panels may be hot, allow

the product to cool before touching.

• Follow proper mounting instructions including torque values.

• Do not allow liquids or foreign objects to enter this product.

Failure to follow these instructions can result in serious injury, or equipment damage.

RIESGO DE DAÑOS MATERIALES Y DE SOBRECALENTAMIENTO DE LA UNIDAD

• Los paneles laterales del producto pueden

estar calientes. Esperar que el producto se enfríe antes de tocarlo.

• Respetar las instrucciones de montaje, y en particular los pares de apretado.

• No dejar que penetren líquidos o cuerpos extraños en el producto.

Si no se respetan estas precauciones pueden producirse graves lesiones, daños materiales.

RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER

• Les panneaux latéraux du produit peuvent être

chauds. Laisser le produit refroidir avant de le toucher.

• Respecter les consignes de montage, et notamment les couples de serrage.

• Ne pas laisser pénétrer de liquide ni de corps étrangers à l'intérieur du produit.

Le non-respect de cette directive peut entraîner, des lésions corporelles graves ou des dommages matériels.

RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO

• I pannelli laterali dell'apparecchio possono

scottare; lasciar quindi raffreddare il prodotto prima di toccarlo.

• Seguire le istruzioni di montaggio corrette.

• Non far entrare liquidi o oggetti estranei in questo

apparecchio.

La mancata osservanza di questa precauzione può causare gravi rischi per l'incolumità personale o danni alle apparecchiature.

GEFAHR VON MATERIALSCHÄDEN UND GEHÄUSEERHITZUNG

• Die Seitenwände können heiß sein. Lassen Sie

das Produkt abkühlen, bevor Sie es berühren.

• Beachten Sie die Montageanweisungen,

• Führen Sie keine Flüssigkeiten oder

Fremdkörper in das Produkt ein.

Die Nichtbeachtung dieser Anweisung kann Körperverletzung oder Materialschäden zur Folge haben.

材料损坏和高温外壳的危险性

• 产品的一侧面板可能很热，在其冷却前请不要触碰。

• 遵照正确的安装说明，包括扭矩值。

• 请勿让液体及其他异物进入本产品。

如不能正确执行这些操作说明，极有可能造成严重人体伤害或者设备的损坏。

Page 7

Panel Mount

Datasheet

ANNEX - ENVIROMENTAL INFORMATION

The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.

Part Name

Semiconductor die

Solder

附件 - 环保信息

此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。

名称铅汞镉六价铬多溴联苯多溴二苯醚

半导体芯片焊接点

Toxic or hazardous Substance and Elements

Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd)

(Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE)

Chromium (Cr (VI))

有毒有害物质或元素件部

biphenyls (PBB)

diphenyl ethers (PBDE)