DataSheet
HAC Series
• Load Voltage range 24 to 660VAC
• Output rating up to 150 Arms
• Zero Voltage or Instantaneous Turn-on options
• AC or DC input control options
• Locking Input Connector
• Optional Transient Protection & installed Thermal Pad
PRODUCT SELECTION
Control Voltage 150A
3-32 VDC
90-140 VAC
150-270 VAC
HAC24D150 ,HAC60D150
HAC24B150 ,HAC60B150
HAC24A150 ,HAC60A150
Panel Mount
AVAILABLE OPTIONS
Control Voltage
A: 150-270 VAC
Series
HAC
Operating Voltage
24: 24-280 VAC
60: 48-660 VAC
Required for valid part number
For options only and not required for valid part number
B: 90-140 VAC
D: 4-32 VDC
A24 150
Rated Load Current
150: 150 Amps
Overvoltage Protection
Blank: Not Included
P: Included (6)
P
Thermal Pad
Blank: Not Included
H: Included
Switching Type
Blank: Zero Voltage Turn-On
-10: Instantaneous Turn-On (5)
-10H
OUTPUT SPECIFICATIONS (1)
Description
Operating Voltage (47-63Hz) [Vrms] 24-280 48-660
Transient Overvoltage [Vpk] 600 1200
Maximum Off-State Leakage Current @ Rated Voltage [mA]
Maximum Off-State dv/dt @ Maximum Rated Voltage [V/µSec]
Maximum Load Current [Arms](2)
Minimum Load Current [Arms] 0.15 0.15
Maximum Surge Current [Apk] 1 Cycle 50/60 Hz 1670/1750 1670/1750
Maximum I²t for fusing (10msec)/(8.33msec)[A²sec]
Maximum On-State Voltage Drop @ Rated Current [Vrms] 1.15 1.15
Thermal Resistance Juncti on to Case (Rjc) [°C/W] 0.15 0.15
Minimum Power Factor (with Maximum load)
Wire Size max (solid/stranded) [AWG/ IEC mm²] (3) 2/0 / 67.4 2/0 / 67.4
Output Terminal Nut Torque Range [in lb (Nm) 225-300 (25.4-33.9) 225-300 (25.4-33.9)
HP Rating UL 508/IEC60957 [HP (KW)]: 240 VAC
HP Rating UL 508/IEC60947 [HP (KW)]: 480 VAC
HAC24x150
1 1
500 500
150 150
13950/12709 13950/12709
0.5 0.5
10 (7.5)
N/A
HAC60x150
N/A
25 (18.75)
Do not forget to visit us at: www.crydom.com
Copyright © 2015 Crydom Inc. Specifications subject to change without notice.
Panel Mount
DataSheet
INPUT SPECIFICATIONS (1)
Description
Control Voltage Range 4-32 VDC (10) 90-140 VAC
Minimum Turn-Off Voltage 4 VDC 90 VAC
Must Turn-Off Voltage 1 VDC 10 VAC
Minimum Input Current (for on-state) [mA] 9 7
Maximum Input Current [mA] 15
Nominal Input Impedance [Ohms]
Maximum Turn-On Time [msec] (4)
Maximum Turn-Off Time [msec]
HACxxD150
Current Regulated
½ Cycle 20
½ Cycle
GENERAL SPECIFICATIONS (1)
Description
Dielectric Strength, Input/Output (50/60Hz) 3750 Vrms
Dielectric Strength, Input/Output/Base (50/60Hz)
Minimum Insulation Resistance (@ 500 V DC)
Maximum Capacitance, Input/Output
Ambient Operating Temperature Range
Ambient Storage Temperature Range
Weight (typical) lbs/grams 0.75/340.2
Housing Material PBT 30% GF, UL 94 V-0
SSR Mounting Torque Range [in lbs/Nm] 18-20 (2-2.2)
LED Input Status Indicator (color)
Humidity 85% non-condensing
Input Terminal (7)
HACxxA150 HACxxB150
150-270 VAC
150 VAC
10 VAC
6
10
Current Regulated
20
30
Parameters
2500 Vrms
9
Ohm
10
10 pF
-30 to 80 °C
-40 to 125 °C
YES (Green)
Detachable barrier strip
12
Current Regulated
30
GENERAL NOTES
(1) All parameters at 25°C unless otherwise specified.
(2) Heat sinking required, see derating curves.
(3) TRM3/0 lug terminal must be used.
(4) Turn-on time for Instantaneous turn-on versions is 0.02 msec.
(5) Instantaneous turn-on version is not recommended for capacitive loads. Use zero turn-on only.
(6) Output will self-trigger (450-600Vpk for HAC24 and 900-1200Vpk for HAC60), not suitable for capacitive loads.
(7) Connector/Plug Not included. See Suggested Mating Connectors/Plugs
(8) Elective Overvoltage Protection, “P” option.
(9) Load can be wired to either SSR output terminal 1 or 2.
(10) Increase minimum voltage by 1V for operations from -20 to -30
°C
WIRING DIAGRAM
AC
V
Load
L2 ( ) L1 ( )
LOAD SIDE
L2
SOLID STATE CONTACTOR
HAC60D150
INPUT
STATUS
4-32 VDC
L1
Input Current vs Input Voltage
Standard Regulated “DC” Inputs
25
20
15
10
Input Current (mA)
5
0
0
5 10 15 20 25 30
DC Input Voltage
(- / ) (+ / )
Do not forget to visit us at: www.crydom.com
Copyright © 2015 Crydom Inc. Specifications subject to change without notice.
MECHANICAL SPECIFICATIONS
FRONT WIRE ENTRY
RIGHT ANGLE
Tolerances: ±0.02 in / 0.5 mm
All dimensions are in: inches [millimeters]
Panel Mount
DataSheet
Standard Stud
LOAD SIDE
L2
L1
0.375 [9.52] -24
2.89
[73.5]
1.70
[43.1]
[47.60]
0.79
[20.1]
1.87
INPUT
STATUS
2.506 [63.65]
3.622 [92.00]
4.094 [103.99]
0.85
[21.7]
Mounting
Hole/Slot
0.19 [4.9] DIA.
1.00
[25.4]
Do not forget to visit us at: www.crydom.com
Copyright © 2015 Crydom Inc. Specifications subject to change without notice.
Molex: 0395332002
Phoenix: MVSTBW 2,5/ 2 -ST-5,08
SUGGESTED MATING
CONNECTORS/PLUGS
Molex: 0395300002
Phoenix: MSTB 2,5/ 2 -ST-5,08
(7)
REAR WIRE ENTRY
Molex: 39533 -3002
Phoenix: MVSTBR 2,5/ 2 -ST-5,08
SURGE CURRENT INFORMATION
1800
1600
1400
1200
1000
800
600
400
Surge Current (Amp)
200
0
0.01 0.1 1 10
Panel Mount
DataSheet
150 A
Surge Duration (Secs)
Non repetitive peak surge current at Tj initial 40°C
THERMAL DERATE INFORMATION (2)
HACxxA150
0.25ºC/W
150
125
100
75
50
25
Load Current (Amps)
0
20 30 40 50 60 70 80
Ambient Temperature (ºC)
0.36ºC/W
0.50ºC/W
HACxxB150,HACxxD150
0.25ºC/W
150
125
100
75
50
25
Load Current (Amps)
0
20 30 40 50 60 70 80
Ambient Temperature (ºC)
0.36ºC/W
0.50ºC/W
Do not forget to visit us at: www.crydom.com
Copyright © 2015 Crydom Inc. Specifications subject to change without notice.
EQUIVALENT CIRCUIT BLOCK DIAGRAM
Panel Mount
DataSheet
ACCESSORIES
AC
AC/DC
Converter
AC
-
DC
+DC
Recommended Accessories
Current
Limiter
Current
Limiter
Diagram:
Diagram:
HAC AC control
Trigger
Circuit
HAC DC control
Trigger
Circuit
(8)
(8)
L2
AC
(9)
AC
L1
L2
AC
(9)
AC
L1
Hardware Kit
HK1 TRM3/0
HS053
HS033
HS023
Heat Sink
Part No.
Thermal Resistance
[ºC/W]
0.5
0.36
0.25
Lug Terminal
AGENCY APPROVALS
Designed in accordance with the requirements of IEC 62314
IEC 61000-4-2 : Electrostatic Discharge: Level 3
IEC 61000-4-4 : Electrically Fast Transients: Level 3
IEC 61000-4-5 : Electricsl Surges: Level 3
949611E
Thermal Pad
HSP-5
512150 .veR
Do not forget to visit us at: www.crydom.com
Copyright © 2015 Crydom Inc. Specifications subject to change without notice.
Panel Mount
DataSheet
DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险
HAZARD OF
ELECTRIC
SHOCK,
EXPLOSION,
OR ARC FLASH.
• Disconnect all
power before
installing or
working with
this equipment.
• Verify all
connections
and replace all
covers before
turning on
power.
Failure to follow
these
instructions will
result in death
or serious injury.
RIESGO DE
DESCARGA
ELECTRICA O
EXPLOSION.
• Desconectar
todos los
suministros de
energia a este
equipo antes
de trabajar
con este equipo.
• Verificar todas
las
conexiones
y colocar todas
las tapas antes
de energizer
el equipo.
El
incumplimiento
de estas
instrucciones
puede provocar
la muerte o
lesiones serias.
RISQUE DE
DESCHARGE
ELECTRIQUE
OU EXPLOSION
• Eteindre
toutes les
sources
d'énergie de
cet appareil
avant de
travailler
dessus de cet
appareil
• Vérifier tous
connections, et
remettre tous
couverts en
olace avant de
mettre sous
De non-suivi de
ces instructions
provoquera la
mort ou des
lésions sérieuses
sérieuses.
GEFAHR EINES
ELEKTRISCHE
N SCHLAGES
ODER EINER
EXPLOSION.
• Stellen Sie
jeglichen
Strom ab, der
dieses Gerät
versorgt, bevor
Sie an dem
Gerät Arbeiten
durchführen
• Vor dem
Drehen auf
Energie alle
Anschlüsse
überprüfen
und alle
Abdeckungen
ersetzen.
Unterlassung
dieser
Anweisungen
können zum
Tode oder zu
schweren
Verletzungen
führen.
RISCHIO DI
SCOSSA
ELETTRICA O
DELL’ESPLOSI
ONE.
• Spenga tutta
l'alimentazion
e che fornisce
questa
apparecchiatu
ra prima del
lavorare a questa
apparecchiatu ra
• Verificare tutti
i colle
gamenti
e sostituire
tutte le coperture
prima della
rotazione
sull'alimentazi one
L'omissione di
seguire queste
istruz ioni
provocherà la
morte o di
lesioni serie
存在电击、
爆炸或电弧
闪烁危险
•
在操作此设
备之前请先
关闭电源。
若不遵守这些说明，
可能会导致严重的
人身伤害甚至死亡。
WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告
RISK OF MATERIAL DAMAGE AND HOT
ENCLOSURE
• The product's side panels may be hot, allow
the product to cool before touching.
• Follow proper mounting instructions including
torque values.
• Do not allow liquids or foreign objects to enter
this product.
Failure to follow these instructions can result in
serious injury, or equipment damage.
RIESGO DE DAÑOS MATERIALES Y DE
SOBRECALENTAMIENTO DE LA UNIDAD
• Los paneles laterales del producto pueden
estar calientes. Esperar que el producto se
enfríe antes de tocarlo.
• Respetar las instrucciones de montaje, y en
particular los pares de apretado.
• No dejar que penetren líquidos o cuerpos
extraños en el producto.
Si no se respetan estas precauciones pueden
producirse graves lesiones, daños materiales.
RISQUE DE DOMMAGE MATERIEL ET DE
SURCHAUFFE DU BOITIER
• Les panneaux latéraux du produit peuvent être
chauds. Laisser le produit refroidir avant de le
toucher.
• Respecter les consignes de montage, et
notamment les couples de serrage.
• Ne pas laisser pénétrer de liquide ni de corps
étrangers à l'intérieur du produit.
Le non-respect de cette directive peut entraîner,
des lésions corporelles graves ou des
dommages matériels.
RISCHIO DI DANNI MATERIALI E D'INVOLUCRO
CALDO
• I pannelli laterali dell'apparecchio possono
scottare; lasciar quindi raffreddare il prodotto
prima di toccarlo.
• Seguire le istruzioni di montaggio corrette.
• Non far entrare liquidi o oggetti estranei in questo
apparecchio.
La mancata osservanza di questa precauzione può
causare gravi rischi per l'incolumità personale o
danni alle apparecchiature.
GEFAHR VON MATERIALSCHÄDEN UND
GEHÄUSEERHITZUNG
• Die Seitenwände können heiß sein. Lassen Sie
das Produkt abkühlen, bevor Sie es berühren.
• Beachten Sie die Montageanweisungen,
• Führen Sie keine Flüssigkeiten oder
Fremdkörper in das Produkt ein.
Die Nichtbeachtung dieser Anweisung kann
Körperverletzung oder Materialschäden
zur Folge haben.
材料损坏和高温外壳的危险性
• 产品的一侧面板可能很热，在其冷却前请
不要触碰。
• 遵照正确的安装说明，包括扭矩值。
• 请勿让液体及其他异物进入本产品。
如不能正确执行这些操作说明，
极有可能造成严重人体伤害或者设备的损坏。
Do not forget to visit us at: www.crydom.com
Copyright © 2015 Crydom Inc. Specifications subject to change without notice.
Panel Mount
DataSheet
ANNEX - ENVIROMENTAL INFORMATION
The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China
Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.
Part
Name
Semiconductor die
Solder
附件 - 环保信息
此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006,
电子信息产品污染控制标识要求。
名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚
半导体芯片
焊接点
Toxic or hazardous Substance and Elements
Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated
(Pb) (Hg) (Cd)
(Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE)
Chromium
(Cr (VI))
有毒有害物质或元素件部
biphenyls
(PBB)
diphenyl ethers
(PBDE)
50
Do not forget to visit us at: www.crydom.com
Copyright © 2015 Crydom Inc. Specifications subject to change without notice.
Loading...