Crydom GNR 90mm Series Data Sheet

DIN Rail Mount

Datasheet

GNR 90mm Series

• Current rating: 25 amps

• Output voltage rating: 48-600 VAC

• Direct Bond Copper (DBC) Substrate

• LED input status indicator

• UL 508 Endurance Rating for Enhaced Reliability

• UL/CSA/TUV Approved, CE Compliant

• Built-in overvoltage protection

• DIN Rail or Panel Mount

• Zero voltage or Instantaneous turn-on output

PRODUCT SELECTION

Control Voltage Zero-Crossing Random Turn-on

4-32 VDC GNR25DCZ GNR25DCR
90-140 VAC GNR25BCZ
180-280 VAC GNR25ACZ

OUTPUT SPECIFICATIONS

(1)

Description

Operating Voltage (47-440Hz) [Vrms]
Transient Overvoltage [Vpk, t=1 min.]
Maximum Load Current [Arms]
Minimum Load Current [Arms]
Maximum Off-State Leakage Current @ Rated Voltage [mArms]
Static Off-State dv/dt ( V/µsec, Ta=25°C)
1 Second Surge Current (Apk Ta=25°C) 50/60 Hz
Forward Voltage Drop (Vpk @ max, Ta=25°C)
Maximum Surge Current (50/60 Hz, 1 cycle) [Apk]

Maximum I² t for Fusing (50/60Hz, 1/2 cycle ) [A² sec]
HP Ratings at 240V / FLA [Arms]
HP Ratings at 380V / FLA [Arms]
HP Ratings at 480V / FLA [Arms]
Min/Max stranded wire
Min/Max solid wire

INPUT SPECIFICATIONS

(2)

(1)

Description

Control Voltage Range (3)
Minimum Turn-On Voltage
Must Turn-Off Voltage
Minimum Input Current (for on-state)

Maximum Input Current
Input Resistance
Maximum Turn-Off Time [msec]
Maximum Turn-On Time [msec]

Min/Max stranded/solid wire

(4)

GNR25

48-600

1100

25

0.1

0.25
500
130

1.50

286/300
410/374

1/4.2
2/4.3
3/4.8

16/8 AWG

16/10 AWG

GNR25DCX

4.0-32 VDC

4.0 VDC

1.0 VDC
22 mA
28 mA

Current Regulated Current Regulated Current Regulated

1/2 Cycle
1/2 Cycle

24/16 AWG

GNR25BCZ

90-140 Vrms

90 Vrms

10 Vrms
15 mArms
19 mArms

20
30

24/16 AWG

GNR25ACZ

180-280 Vrms

180 Vrms

10 Vrms

19 mA
24 mA

20
30

24/16 AWG

Copyright © 2018 Crydom Inc. Specifications subject to change without notice.

DIN Rail Mount

Datasheet

GENERAL SPECIFICATIONS

Ambient Operating Temperature Range (3)
Ambient Storage Temperature Range

Dielectric Strength, Input to Output (50/60Hz)
Dielectric Strength, Input/Output to Ground (50/60Hz)
Maximum Capacitance, Input/Output
Housing Material
Input Status Indicator

Weight (typical)
Recommended Terminal Screw Torque Range:

(1)

GENERAL NOTES

All parameters at 25°C unless otherwise specified.

(1)
(2) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1
(3) For 180-280 VAC Control. Maximum Ambient operating temperatures is 60°C.
(4)

Turn-on time for Instantaneous version (R suffix) is 0.1 msec (for DC control only).

(5) TUV Certification according to EN 60950-1/A1:2010

For additional information or specific questions, contact Crydom Technical Support.

MECHANICAL SPECIFICATIONS

Tolerances: ±0.02 in / 0.5 mm
All dimensions are in: inches [millimeters]

(1)

ParametersDescription

-20 to 80°C

-40 to 100 °C
4000 Vrms

2500 Vrms

8 pF

UL 94V0 (self extinguishing)

Green LED

21.17 oz (600g)

5.0-6.0 in-lb (0.6-0.7 Nm)

3.82

[97.0]

3.47

[88.1]

4.86

[123.4]

GNR25DCZ

3.59

[91.2]

0.18

[4.5]

3.54

[90.0]

3.26

[82.8]

GNR25DCZ

3.26

[82.8]

Copyright © 2018 Crydom Inc. Specifications subject to change without notice.

WIRING DIAGRAM

DIN Rail Mount

Datasheet

L3

LOAD

A1

Load can be wired in Position A or B

A2

Load can be wired in Position A or B

Load can be wired in Position A or B

A

B

T3

LOAD

L2

LOAD

A

B

T2

LOAD

L1

LOAD

A

B

T1

LOAD

AC

AC

AC

AC

AC

AC

THERMAL DERATE INFORMATION

GNR25xxx

25

20

15

10

5

Load Current per phase (Amps)

0

Ambient Temperature (ºC)

*GNR25A Series rated to 60°C max ambient

403020100 50 60 70 80

Copyright © 2018 Crydom Inc. Specifications subject to change without notice.

AGENCY APPROVALS

Designed in accordance with the requirements of IEC 62314

DIN Rail Mount

Datasheet

E79183

LR 38595

(5)

EMC Compatibility

Designed in accordance with the requirements of IEC 62314
IEC 62314

IEC 60068-2-6 35mm/10-55Hz
IEC 60068-2-27 15G / 11ms
IEC 61000-4-2 Level 3 Electrostatic Discharge
IEC 61000-4-3 Level 3 Radiated Electromagnetic Noise
IEC 61000-4-4 Level 3 Immunity to Electrically Fast Transients
IEC 61000-4-5 Level 3 Immunity to Electrical Surges
IEC 61000-4-6 Level 3 Conducted Electromagnetic Noise
CISPR 11 Class A Conducted and Radiated Noise for Industrial Environments

Copyright © 2018 Crydom Inc. Specifications subject to change without notice.

Rev. 122018
ECN 20613

DIN Rail Mount

Datasheet

DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险

HAZARD OF
ELECTRIC
SHOCK,
EXPLOSION,
OR ARC FLASH.

• Disconnect all
power before
installing or
working with
this equipment.

• Verify all
connections
and replace all
covers before
turning on
power.

Failure to follow
these
instructions will
result in death
or serious injury.

RIESGO DE
DESCARGA
ELECTRICA O
EXPLOSION.

• Desconectar
todos los
suministros de
energia a este
equipo antes
de trabajar

con este equipo.

• Verificar todas
las

conexiones
y colocar todas
las ta

pas antes
de energizer
el equipo.

El
incumplimiento
de estas
instrucciones
puede provocar
la muerte o
lesiones serias.

RISQUE DE
DESCHARGE
ELECTRIQUE
OU EXPLOSION

• Eteindre
toutes les
sources
d'énergie de
cet appareil
avant de
travailler
dessus de cet
appareil

• Vérifier tous

connections, et

remettre tous
couverts en
olace avant de

mettre sous

De non-suivi de
ces instructions
provoquera la
mort ou des
lésions sérieuses
sérieuses.

GEFAHR EINES
ELEKTRISCHE
N SCHLAGES
ODER EINER
EXPLOSION.

• Stellen Sie
jeglichen
Strom ab, der
d

ieses Gerät

versorgt, bevor

Sie an dem

Gerät Arbeiten
durchführen

• Vor dem
Drehen auf
Energie alle
Anschlüsse
überprüfen
und alle
Abdeckungen
ersetzen.

Unterlassung
dieser
Anweisungen
können zum
Tode oder zu
schweren
Verletzungen
führen.

RISCHIO DI
SCOSSA
ELETTRICA O
DELL’ESPLOSIONE.

• Spenga tutta
l'alimentazione
che fornisce
questa
apparecchiatura
prima di lavorare
a questa

apparecchiatura

• Verificare tutti
i collegamenti
e sostituire

tte le coperture

tu
prima
dell’accensione

L'omissione di
queste istruzioni
provocherà la
morte o
lesioni serie

存在电击、
爆炸或电弧
闪烁危险

•

在操作此设
备之前请先
关闭电源。

若不遵守这些说明，
可能会导致严重的
人身伤害甚至死亡。

WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告

RISK OF MATERIAL DAMAGE AND HOT
ENCLOSURE

• The product's side panels may be hot, allow

the product to cool before touching.

• Follow proper mounting instructions including
torque values.

• Do not allow liquids or foreign objects to enter
this product.

Failure to follow these instructions can result in
serious injury, or equipment damage.

RIESGO DE DAÑOS MATERIALES Y DE
SOBRECALENTAMIENTO DE LA UNIDAD

• Los paneles laterales del producto pueden

estar calientes. Esperar que el producto se
enfríe antes de tocarlo.

• Respetar las instrucciones de montaje, y en
particular los pares de apretado.

• No dejar que penetren líquidos o cuerpos
extraños en el producto.

Si no se respetan estas precauciones pueden
producirse graves lesiones, daños materiales.

RISQUE DE DOMMAGE MATERIEL ET DE
SURCHAUFFE DU BOITIER

• Les panneaux latéraux du produit peuvent être

chauds. Laisser le produit refroidir avant de le
toucher.

• Respecter les consignes de montage, et
notamment les couples de serrage.

• Ne pas laisser pénétrer de liquide ni de corps
étrangers à l'intérieur du produit.

Le non-respect de cette directive peut entraîner,
des lésions corporelles graves ou des
dommages matériels.

RISCHIO DI DANNI MATERIALI E D'INVOLUCRO
CALDO

• I pannelli laterali dell'apparecchio possono

scottare; lasciar quindi raffreddare il prodotto
prima di toccarlo.

• Seguire le istruzioni di montaggio corrette.

• Non far entrare liquidi o oggetti estranei in questo

apparecchio.

La mancata osservanza di questa precauzione può
causare gravi rischi per l'incolumità personale o
danni alle apparecchiature.

GEFAHR VON MATERIALSCHÄDEN UND
GEHÄUSEERHITZUNG

• Die Seitenwände können heiß sein. Lassen Sie

das Produkt abkühlen, bevor Sie es berühren.

• Beachten Sie die Montageanweisungen,

• Führen Sie keine Flüssigkeiten oder

Fremdkörper in das Produkt ein.

Die Nichtbeachtung dieser Anweisung kann
Körperverletzung oder Materialschäden
zur Folge haben.

材料损坏和高温外壳的危险性

• 产品的一侧面板可能很热 在其冷却前请
不要触碰。

• 遵照正确的安装说明 包括扭矩值。

• 请勿让液体及其他异物进入本产品。

如不能正确执行这些操作说明，
极有可能造成严重人体伤害或者设备的损坏。

Copyright © 2018 Crydom Inc. Specifications subject to change without notice.

DIN Rail Mount

Datasheet

ANNEX - ENVIROMENTAL INFORMATION

The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China
Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.

Part
Name

Semiconductor die

Solder

附件 - 环保信息

此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 2006,
电子信息产品污染控制标识要求。

名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚

半导体芯片
焊接点

Toxic or hazardous Substance and Elements

Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated
(Pb) (Hg) (Cd)

(Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE)

Chromium
(Cr (VI))

有毒有害物质或元素件部

biphenyls
(PBB)

diphenyl ethers
(PBDE)

50

Copyright © 2018 Crydom Inc. Specifications subject to change without notice.