Crydom GNR 22.5mm Series Data Sheet

DIN Rail Mount

Datasheet

GNR 22.5mm Series

• Current ratings of 10, 20 and 30 amps

• Output voltage ratings: 24-280 and 48-600 VAC

• Direct Bond Copper (DBC) Substrate

• LED input status indicator

• UL 508 Endurance Rating for Enhanced Reliability

• UL/CSA/TUV Approved, CE Compliant

• Built-in overvoltage protection

• DIN Rail or Panel Mount

• Zero voltage or Instantaneous turn-on output

PRODUCT SELECTION

Control Voltage 10A 30A

4-32 VDC GNR10DHZ
90-140 VAC GNR10BHZ
180-280 VAC GNR10AHZ

20A

GNR20DHZ
GNR20BHZ
GNR20AHZ

GNR30DHZ
GNR30BHZ
GNR30AHZ

AVAILABLE OPTIONS

Series

GNR A H Z10

Rated Load Current
10: 10 Amps
20: 20 Amps
30: 30 Amps

Required for valid part number

For options only and not required for valid part number

OUTPUT SPECIFICATIONS

Description

Operating Voltage (47-440Hz) [Vrms]
Transient Overvoltage [Vpk, t=1 min.]
Maximum Off-State Leakage Current @ Rated Voltage [mArms]
Static Off-State dv/dt ( V/µsec, Ta=25°C)
Maximum Load Current [Arms]
Minimum Load Current [Arms]
Maximum Surge Current (50/60 Hz, 1 cycle) [Apk]
1 Second Surge Current (Apk Ta=25°C) 50/60 Hz

Forward Voltage Drop (Vpk @ max, Ta=25°C)
Maximum I² t for Fusing (50/60Hz, 1/2 cycle ) [A² sec]

HP Ratings at 120V / FLC [Arms]
HP Ratings at 240V / FLC [Arms]
Min/Max stranded wire
Min/Max solid wire

(1)

(2)

Operating Voltage
A: 180-260 VAC
B: 90-140 VAC
D: 4-32 VDC

Terminal Layout
C: Contactor configuration
H: Relay configuration

GNR10

24-280

600

0.1

500

10

100

190/200

65

1.5

182/166

-

-

16/8 AWG

16/10 AWG

Switching Type
R: Instantaneous Turn-on

(for DC control only)
Z: Zero voltage Turn-on

GNR20

48-600

1100

0.1

500

20

100

286/300

85

1.35

410/374

1.2/9.8
1/8

16/8 AWG

16/10 AWG

GNR30

48-600

1100

0.1

500

30

100

716/750

150

1.35

2562/2334

3/4 / 13.8

2/12

16/8 AWG

16/10 AWG

Copyright © 2016 Crydom Inc. Specifications subject to change without notice.

DIN Rail Mount

Datasheet

INPUT SPECIFICATIONS

Description

Control Voltage Range (3)
Minimum Turn-On Voltage
Must Turn-Off Voltage
Minimum Input Current (for on-state)

Maximum Input Current
Input Resistance
Maximum Turn-Off Time [msec]
Maximum Turn-On Time [msec]

Min/Max stranded/solid wire

(4)

GENERAL SPECIFICATIONS

Ambient Operating Temperature Range (3)
Ambient Storage Temperature Range

Dielectric Strength, Input to Output (50/60Hz)
Dielectric Strength, Input/Output to Ground (50/60Hz)
Maximum Capacitance, Input/Output
Housing Material
Input Status Indicator

Weight (typical)

(1)

GNRxxDx

4.0-32 VDC

Current Regulated Current Regulated Current Regulated

1/2 Cycle
1/2 Cycle

24/16 AWG

(1)

GENERAL NOTES

All parameters at 25°C unless otherwise specified.

(1)
(2) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1
(3) For 180-280 VAC Control. Maximum Ambient operating temperatures is 60°C.
(4)

Turn-on time for Instantaneous version (R suffix) is 0.1 msec (for DC control only).

(5) TUV Certification according to EN 60950-1/A1:2010

4.0 VDC

1.0 VDC
6 mA

10 mA

GNRxxBx

90-140 Vrms

90 Vrms
10 Vrms

5 mArms

23 mArms

20
30

24/16 AWG

ParametersDescription

-20 to 80°C

-40 to 100 °C
4000 Vrms

2500 Vrms

8 pF

UL 94V0 (self extinguishing)

Green LED

7.94 oz (225g)

GNRxxAx

180-280 Vrms

180 Vrms

10 Vrms

6 mA
2 mA

20
30

24/16 AWG

For additional information or specific questions, contact Crydom Technical Support.

MECHANICAL SPECIFICATIONS

Tolerances: ±0.02 in / 0.5 mm
All dimensions are in: inches [millimeters]

3.47

[88.2]

(1)

4.75

[120.8]

0.18
[4.6]

Contactor Configuration

3.54

[89.8]

3.85

[97.8]

0.18

[4.5] DIA.

0.21

[5.3] DIA.

0.19
[4.8]

0.68

[17.3]

0.87

[22.5]

0.21
[5.3]

3.54

[89.8]

0.70

[17.8]

Copyright © 2016 Crydom Inc. Specifications subject to change without notice.

DIN Rail Mount

Datasheet

3.47

[88.2]

4.75

[120.8]

Relay Configuration

3.54

[89.8]

0.18

[4.6]

3.85

[97.8]

0.18

[4.5] DIA.

0.21

[5.3] DIA.

0.19
[4.8]

0.68

[17.3]

0.87

[22.5]

0.21
[5.3]

3.54

[89.8]

0.70

[17.8]

WIRING DIAGRAM

A1

DC +

DC -

A2

AC

A1

+

AC

-

A2

DC Input Equivalent Circuit

AC Input Equivalent Circuit

L1

Load can be wired in Position A or B

T1

L1

Load can be wired in Position A or B

T1

LOAD

A

B

LOAD

LOAD

A

B

LOAD

AC

AC

AC

AC

Copyright © 2016 Crydom Inc. Specifications subject to change without notice.

THERMAL DERATE INFORMATION

DIN Rail Mount

Datasheet

10

7.5

5

2.5

Load Current (Amps)

0

GNR10xxx

403020100 50 60 70 80

*GNR10A Series rated to 60°C max ambient

30

25

20

15

10

Load Current (Amps)

5

Load Current (Amps)

GNR30xxx

GNR20xxx

20

15

10

5

0

*GNR20A Series rated to 60°C max ambient

403020100 50 60 70 80

Ambient Temperature (ºC)Ambient Temperature (ºC)

0

0

Ambient Temperature (ºC)

*GNR30A Series rated to 60°C max ambient

AGENCY APPROVALS

Designed in accordance with the requirements of IEC 62314

E79183

LR 38595

(5)

EMC Compatibility

Designed in accordance with the requirements of IEC 62314
IEC 62314

IEC 60068-2-6 35mm/10-55Hz
IEC 60068-2-27 15G / 11ms
IEC 61000-4-2 Level 3 Electrostatic Discharge
IEC 61000-4-3 Level 3 Radiated Electromagnetic Noise
IEC 61000-4-4 Level 3 Immunity to Electrically Fast Transients
IEC 61000-4-5 Level 3 Immunity to Electrical Surges
IEC 61000-4-6 Level 3 Conducted Electromagnetic Noise
CISPR 11 Class A Conducted and Radiated Noise for Industrial Environments

40302010

50 60 70 80

Copyright © 2016 Crydom Inc. Specifications subject to change without notice.

Rev. 082316

DIN Rail Mount

Datasheet

DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险

HAZARD OF
ELECTRIC
SHOCK,
EXPLOSION,
OR ARC FLASH.

• Disconnect all
power before
installing or
working with
this equipment.

• Verify all
connections
and replace all
covers before
turning on
power.

Failure to follow
these
instructions will
result in death
or serious injury.

RIESGO DE
DESCARGA
ELECTRICA O
EXPLOSION.

• Desconectar
todos los
suministros de
energia a este
equipo antes
de trabajar

con este equipo.

• Verificar todas
las

conexiones
y colocar todas
las

tapas antes
de energizer
el equipo.

El
incumplimiento
de estas
instrucciones
puede provocar
la muerte o
lesiones serias.

RISQUE DE
DESCHARGE
ELECTRIQUE
OU EXPLOSION

• Eteindre
toutes les
sources
d'énergie de
cet appareil
avant de
travailler
dessus de cet
appareil

• Vérifier tous

connections, et

remettre tous
couverts en
olace avant de

mettre sous

De non-suivi de

ces instructions
provoquera la
mort ou des
lésions sérieuses
sérieuses.

GEFAHR EINES
ELEKTRISCHE
N SCHLAGES
ODER EINER
EXPLOSION.

• Stellen Sie
jeglichen
St

rom ab, der
dieses Gerät
versorgt, bevor

Sie an dem

Gerät Arbeiten
durchführen

• Vor dem
Drehen auf
Energie alle
Anschlüsse
überprüfen
und alle
Abdeckungen
ersetzen.

Unterlassung
dieser
Anweisungen
können zum
Tode oder zu
schweren
Verletzungen
führen.

RISCHIO DI
SCOSSA
ELETTRICA O
DELL’ESPLOSIONE.

• Spenga tutta
l'alimentazione
che fornisce
questa
apparecchiatura
prima di lavorare
a questa

apparecchiatura

• Verificare tutti
i collegamenti
e sostituire

utte le coperture

t
prima
dell’accensione

L'omissione di
queste istruzioni
provocherà la
morte o
lesioni serie

存在电击、
爆炸或电弧
闪烁危险

•

在操作此设
备之前请先
关闭电源。

若不遵守这些说明，
可能会导致严重的
人身伤害甚至死亡。

WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告

RISK OF MATERIAL DAMAGE AND HOT
ENCLOSURE

• The product's side panels may be hot, allow

the product to cool before touching.

• Follow proper mounting instructions including
torque values.

• Do not allow liquids or foreign objects to enter
this product.

Failure to follow these instructions can result in
serious injury, or equipment damage.

RIESGO DE DAÑOS MATERIALES Y DE
SOBRECALENTAMIENTO DE LA UNIDAD

• Los paneles laterales del producto pueden

estar calientes. Esperar que el producto se
enfríe antes de tocarlo.

• Respetar las instrucciones de montaje, y en
particular los pares de apretado.

• No dejar que penetren líquidos o cuerpos
extraños en el producto.

Si no se respetan estas precauciones pueden
producirse graves lesiones, daños materiales.

RISQUE DE DOMMAGE MATERIEL ET DE
SURCHAUFFE DU BOITIER

• Les panneaux latéraux du produit peuvent être

chauds. Laisser le produit refroidir avant de le
toucher.

• Respecter les consignes de montage, et
notamment les couples de serrage.

• Ne pas laisser pénétrer de liquide ni de corps
étrangers à l'intérieur du produit.

Le non-respect de cette directive peut entraîner,
des lésions corporelles graves ou des
dommages matériels.

RISCHIO DI DANNI MATERIALI E D'INVOLUCRO
CALDO

• I pannelli laterali dell'apparecchio possono

scottare; lasciar quindi raffreddare il prodotto
prima di toccarlo.

• Seguire le istruzioni di montaggio corrette.

• Non far entrare liquidi o oggetti estranei in questo

apparecchio.

La mancata osservanza di questa precauzione può
causare gravi rischi per l'incolumità personale o
danni alle apparecchiature.

GEFAHR VON MATERIALSCHÄDEN UND
GEHÄUSEERHITZUNG

• Die Seitenwände können heiß sein. Lassen Sie

das Produkt abkühlen, bevor Sie es berühren.

• Beachten Sie die Montageanweisungen,

• Führen Sie keine Flüssigkeiten oder

Fremdkörper in das Produkt ein.

Die Nichtbeachtung dieser Anweisung kann
Körperverletzung oder Materialschäden
zur Folge haben.

材料损坏和高温外壳的危险性

• 产品的一侧面板可能很热，在其冷却前请
不要触碰。

• 遵照正确的安装说明，包括扭矩值。

• 请勿让液体及其他异物进入本产品。

如不能正确执行这些操作说明，
极有可能造成严重人体伤害或者设备的损坏。

Copyright © 2016 Crydom Inc. Specifications subject to change without notice.

DIN Rail Mount

Datasheet

ANNEX - ENVIROMENTAL INFORMATION

The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China
Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.

Part
Name

Semiconductor die

Solder

Toxic or hazardous Substance and Elements

Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated
(Pb) (Hg) (Cd)

Chromium
(Cr (VI))

biphenyls
(PBB)

diphenyl ethers
(PBDE)

50

Copyright © 2016 Crydom Inc. Specifications subject to change without notice.