Crux BEEMZ-30 User Manual

BLUETOOTH INTERFACE FOR SELECT 2002-UP MAZDA VEHICLES

TO FACTORY

REV.050614

BEEMZ-30

IMPORTANT: NOT COMPATIBLE WITH PREMIUM SOUND SYSTEMS (AMPLIFIED SYSTEMS)

APPLICATIONS

Mazda

2011 - 2012 Mazda2 2004 - 2011 Mazda3 2012 - 2014 Mazda3* 2006 - 2010 Mazda5 2012 - 2014 Mazda5* 2003 - 2011 Mazda6 2006 - 2011 MX-5 Miata 2004 - 2011 RX-8 2002 - 2006 MPV 2007 - 2011 Speed3 2006 - 2007 Speed6 2007 - 2011 CX-7 2007 - 2011 CX-9 2008 - 2011 Tribute

Notes:

*Important: These applications require the installer to place a Diode on the 24-Pin White harness, from the Crux T-Harness. See slip sheet included in the Manual for further information & instructions.

**2008-2010 Tribute requires a different harness: Crux Part Number 3196; must be special ordered.

work. Following these instructions from “Start” to” Finish” will ensure

9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.

PRELIMINARY:

- Disconnect the positive(+) battery cable for radios that are non-navigation. Radios that are navigation ready should not disconnect the battery cable. Please use caution when installing. Do not install the interface near or on the vehicle’s HVAC system. This will prevent overheating and condensation build up.

Use overview to help you determine installation method.

INSTALLATION

1. Remove the factory radio to gain access to the factory radio wiring connectors.

2. Disconnect the factory connectors from the rear of the factory radio.

3. Connect the male connectors of the interface power harness into the factory radio.

4. Reconnect the factory connectors into the mating connectors of the interface harness.

5. Connect the male 3-pin connector into the pigtail connector.

6. Route the microphone to a desired location, (for example near the rear view mirror).

7. Re-install a factory radio back into the vehicle’s dash.

FIG. 1 (Multi-PIN CONNECTORS):

HARNESS

24-PIN

(male plug)

MIC

BALL JOINT

24-PIN

(female plug)

24-PIN

(male plug)

3-PIN

(male plug)

12-PIN

(male plug)

MOUNTING THE MICROPHONE

1. Insert the mounting clip into the ball joint on the microphone.

2. Mount the clip on your visor or near the rear view mirror.

3. Route the remaining cable along the edge of the roof liner and towards the back of the radio, hiding the cable from sight.

RADIO

INITIAL PAIRING TO THE VOICE PROMPTS:

1. READY (POWER ON)

2. SEARCHING PHONES (FOR PREVIOUS PAIRED PHONES)

3. PLEASE SEARCH AND SELECT THE “BEE LINE” DEVICE FROM MOBILE PHONE AND ENTER “0000”.

4. YOU ARE NOW READY TO USE THE HF SYSTEM. Note: The Bluetooth interface will remember up to the last 8 devices.

power back on to re-attempt, if unsuccessful please contact our tech support line.

AUTO RE-CONNECT:

1. The BEEMZ-30 module will automatically re-connect the a previously paired mobile phone when the ignition is turned “ON” to the vehicle and the mobile phone’s Bluetooth feature is also on.

Note: The Bluetooth module will re-connect with the last mobile phone’s it was paired with. If no mobile phone is not found, it will revert to the pairing process.

SUPPORTED RADIOS

FM1/2

AM CD MD/TAPE

SEEK

TRACK

APC

VOL

PUSH

H M

LOAD

POWER

WMA

SEEK TRACK

DISC

1 2 3 4 5 6

AM SIRIUS

FM1/2

DISC

FOLDER

CAT

DISC

FOLDER

CAT

DISP TEXT/ESN AUTO-M SCAN

PROG

RPT

RDM

TUNE

FILE

PUSH

CLOCK

AUX MP3

RPT

1 2 3

RDM

4 5 6

PUSH

SCAN

AUTO-M

TUNE

AUDIO CONT.

:00

Note: If an incoming call is answered from the mobile phone’s keypad, the call will direct itself to the headset on the mobile phone. To re-direct the phone call to the Crux interface, it must be done directly from the mobile phone.

Note: When transferring a phone call to the mobile phone for privacy, the user must re-connect the Crux interface and the mobile phone by

selecting the module from the device menu on the phone. Note: If after ending a call the radio is powered “OFF”, you must power “ON” the radio to regain volume control.

FM1/2 AM SAT CD MEDIA

SEEK

TRACK

APC

1 2 3 4 5 6

LOAD

TRACK/SEEK

REPLAY

1 2

SAT/BT

AUTO-M

TEXT

SCAN

PUSH

VOLUME

FM AM

CD SAT

POWER

H M 00

AUX

4 5

PUSH

AUDIO CONT

TUNE

DISP/ESN

SCAN

AUTO

RPT

DISC/FOLDER

CATEGORY

RDM

USING THE STEERING WHEEL CONTROL BUTTONS

VOICE DIAL HOLD SEEK DN FOR 2 SECONDS

ANSWER PRESS SEEK UP BUTTON ONCE

END A CALL PRESS SEEK DN BUTTON ONCE

REJECT PRESS SEEK DN BUTTON ONCE

ANSWER SECOND CALL PRESS SEEK UP BUTTON ONCE

SWITCH BETWEEN CALLS PRESS SEEK UP BUTTON ONCE

INCREASE VOLUME PRESS VOLUME UP ONCE

DECREASE VOLUME PRESS VOLUME DN ONCE

PRIVACY MODE PRESS SEEK UP ONCE

Note: Premium Audio Systems need to “Turn On” the radio for handsfree audio to be heard.

All features of this module may vary by mobile phone manufacturer. For questions on your mobile phone’s features, please reference the mobile phone’s user manual for information.

BLUETOOTH INTERFACE FOR SELECT 2002-UP MAZDA VEHICLES

BEEMZ-30

IMPORTANT: NOT COMPATIBLE WITH PREMIUM SOUND SYSTEMS (AMPLIFIED SYSTEMS)

APPLICATIONS

Mazda

Notes:

**2008-2010 Tribute requires a different harness: Crux Part Number 3196; must be special ordered.

USING THE MENU STRUCTURE:

To enter the Voice Menu you must do the following:

1. Hold Seek Down fro 2 seconds.

2. Press Seek Up once.

3. Hold Seek Down fo 2 seconds.

You are now at the top of the menu.

4. Press Seek Down to scroll though the menu options.

5. Press Seek Up to select a menu option.

MISSED CALLS:

Continue to press the “SEEK DN” button till you hear the interface announce “MISSED CALLS”, and wait for the numbers to be announced.

3. When the number you wish to dial is announced, press the “SEEK UP” button once to make the call.

INCOMING CALLS:

Continue to press the “SEEK DN” button till you hear the interface announce “INCOMING CALLS”, and wait for the numbers to be announced.

3. When the number you wish to dial is announced, press the “SEEK UP” button once to make the call.

OUTGOING CALLS:

Continue to press the “SEEK DN” button till you hear the interface announce “OUTGOING CALLS”, and wait for the numbers to be announced.

3. When the number you wish to dial is announced, press the “SEEK UP” button once to make the call.

PHONE MUST BE UNPAIRED TO ENTER THE FOLLOWING MENU STRUCTURE

SETTING TTS VOLUME:

Continue to press the “SEEK DN” button twice till you hear the interface announce “SETTING VOLUME”, and wait for her announcement.

3. Set the TTS volume by pressing the volume Vol+ and Vol- waiting for the announcement. Each announcement will indicate the volume level of the TTS.

4. When the desired volume level is reached, press the “SEEK UP” button once to select.

DELETE ALL PAIRED DEVICES:

This feature allows you to delete all paired devices on the interface. The module does NOT allow the user to only clear one device. The module will delete all previously paired devices only

Continue pressing the “SEEK DN” button twice till you hear the interface announce “DO YOU WANT TO DELETE PAIRED PHONE LIST”.

4. The interface will ask “ARE YOU SURE”, press the “SEEK UP”

VOL

Have a bad connection when using the A2DP or Handsfree

VOL

MODE

VOL

MODE

Are you experiencing random static interuptions durring your phone calls?

MODE

Have you paired your mobile device, and get no sound from the radio? Try reseting the TTS volume setting.

MODE

Delete all paired devices on your mobile device and on the UBT. (See Using The Menu Structure)

Remove the battery on the mobile device for a minimum of 15 Seconds.

With the phone paired to the UBT, enter the “SETTING TTS VOLUME” under menu structure. The default level is at volume 4.

Note: The menu structures only remember the last 24 numbers in the call log from dialed from the mobile phone.

Note: All menu structures work in 3 second increments. If after 3 seconds the interface will time-out.