The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the presence
of “dangerous voltage” inside the product that may constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating
and maintenance instructions in the literature accompanying the product.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
THE A300
COVER.
— Read all the safety and operating instructions before operating this product.
— Adhere to all warnings on the product and in the operating instructions.
— Unplug this product from the wall outlet before cleaning.
— Do not use this product near water.
Ventilation
— Slots and openings in the cabinet are provided for ventilation to ensure reliable operation
— The product should be situated away from heat sources such as radiators, heat registers,
— Operate this product only from the type of power source indicated on the
voltage selector switch
— Power supply cords should be routed so that they are not likely to be
— Unplug the unit from the wall outlet for added protection during a lightning storm
when it is left
— Do not overload wall outlets or extension cords. This can result in a fire or electric shock.
— Never push objects of any kind into this product through any openings;
— Do not attempt to repair or service this product yourself. Opening or removing covers may
— Unplug this product from the wall outlet and refer servicing to qualified
Replacement Parts
— When replacement parts are required, be sure the service technician
Important Safety Instructions
A300 OWNER’S GUIDE
2
Introduction and Front Panel Controls
Auto. Note: It is normal for the A300 Power Standby Indicator to flash briefly while the A300 is turned on.
The A300 is in “standby” mode when the Power Standby Indicator is illuminated red.
The LPF, or Low Pass Filter, removes unwanted high frequency content from the output signal. Adjusting
Volume Knob:
Adjust the intensity of motion by turning the Volume Knob clockwise to increase, or counter-
The
vents overload and distortion during maximum
The A300 is
1
1
2
3
4
2
3
4
5
5
A300 OWNER’S GUIDE
3
LFE Input Jack:
LFE Out Jack:
The LFE Out Jack
The LFE Out Jack is a pass-through for the LFE Input Jack signal.
There are separate Output Binding Post pairs for connection to left and right TES100
Actuators. Each - and + Binding Post will accept a bare speaker wire up to AWG 10 or two wires up to AWG 14. A single
S
Rear Panel Connections and Controls
LFE Input Jack:
LFE Input Jack:
LFE Input Jack:
LFE Out Jack:
LFE Out Jack:
LFE Out Jack:
6
7
8
9
A300 OWNER’S GUIDE
4
A300 is hidden from sight. Connect a stereo 1/8” control cable from your remote control system to the IR Input Jack.
A single speaker cable can be used to power one to four TES-100 actuators in a Mono
“Mono” position of the Bridging Switch.
Two or
One TES-100 Actuator can be
/ch
and
THE A300 POWER C
Actuators. Do not use more than four total TES 100 Actuators.
The Ground Switch disconnects or “lifts” the audio circuit ground from the chassis ground. This
“Lift” position.
Voltage Selector Switch (115v - 230v AC):
The 115V position of this switch is correct for North America; most
Plug the AC Power
10
11
Rear Panel Connections and Controls
12
13
14
15
16
17
A300 OWNER’S GUIDE
5
Auto Turn On
Audio sense 15mV
AC Power Requirement
variable from 20Hz to 600Hz
variable from 20Hz to 600Hz
Troubleshooting and Specifications
Troubleshooting
/ch
A300 OWNER’S GUIDE
6
Warranty
A300 OWNER’S GUIDE
7
Loading...