Crown Verity BI-48, BI-30, BI-36 User Manual

CROWN VERITY INC., 37 ADAMS BLVD., BRANTFORD, ON. CAN. N3S 7V8

TEL: [phone] FAX: [phone]

www.crownverity.com

Email: [e-mail]

OWNER’S MANUAL

“SUPPLEMENT FOR BUILT-IN UNITS”

MODELS: BI-30, BI-36 & BI-48

REVISED MARCH, 2003

*PLEASE RETAIN FOR FUTURE REFERENCE

THANK YOU for purchasing this quality product. Your Crown Verity Inc. charbroiler
will give you years of outdoor cooking enjoyment.

Please read this manual carefully to ensure safe operation and to maximize your
cooking enjoyment. It is your responsibility to see that your unit is properly
assembled, installed and cared for. Failure to follow instructions in this manual could
result in serious bodily injury and/or property damage.

WARNING: Improper installation, adjustment, alteration, service or
maintenance can cause property damage, injury or death. Read the
installation, operating and maintenance instructions thoroughly before
installing or servicing this equipment.

1

This owner’s manual was created as a supplement to the standard MCB manual to assist
you and the contractor(s) you have hired to install the BI-30, BI-36 or BI-48.

The standard MCB manual contains a lot of valuable safety and operation information.

Please read through the manual before operating your charbroiler, paying special
attention to the safety, operation, and shut down instructions. Not all of the information
will apply to you. It will be up to you to decide what applies and what doesn’t. We at
Crown Verity inc. felt it better to include the standard manual for reference rather than
leave you short-handed on proper operational, maintenance and safety precautions.
Questions/concerns? Call 519-751-1800.

Whether you are connecting your broiler to natural gas, a fixed LP supply, or self­contained LP cylinders (propane tanks), this manual should give you enough information
to get the job done.

CROWN VERITY INC., 37 ADAMS BLVD., BRANTFORD, ON. CAN. N3S 7V8

TEL: [phone] FAX: [phone]

www.crownverity.com

Email: [e-mail]

2

PLANNING YOUR PROJECT

A built-in Crown Verity Inc. charbroiler requires some sort of support structure to house
the unit. In all cases, this is a custom made project involving a gas technician and
possibly other contractors, i.e. mason, carpenter, electrician, plumber, etc. It is
important that you form a clear and concise plan before beginning. We strongly suggest
purchasing your broiler and accessories before beginning. Once you have the broiler on­site and have read through this manual, you should meet with the contractors involved
and give them the information they need from this manual so they can outline any
concerns they may have so that everyone can work together to achieve a finished
product that is aesthetically appealing, safe, and convenient for everyone to use.

As simple or elaborate as your project may be, proper planning is key. Each contractor,
as few or as many as there may be, will have some concerns regarding the placement of
their equipment or materials with respect to access, clearance from hot surfaces,
ventilation and routing. etc.

Points to remember when planning:

1. Is the selected location appropriate for a charbroiler? Remember, they can be greasy
and messy and they can be a fire hazard.

2. Is the location properly ventilated? All broilers will produce smoke and possibly noxious
fumes.

3. Are the materials selected appropriate (durability, weather resistance, heat
resistance, and clean-up are primary concerns)?

CROWN VERITY INC., 37 ADAMS BLVD., BRANTFORD, ON. CAN. N3S 7V8

TEL: [phone] FAX: [phone]

www.crownverity.com

Email: [e-mail]

3

The following diagrams represent mechanical clearances (areas that must be kept free of
obstructions). Of particular concern is the roll dome. Whether or not you purchased one
with your unit, there are some clearances to maintain should you wish to add or remove
a roll dome (Diagram #1). Also, the roll dome requires some clearance in order to
operate (Diagram #2).

Diagram #1

CROWN VERITY INC., 37 ADAMS BLVD., BRANTFORD, ON. CAN. N3S 7V8

TEL: [phone] FAX: [phone]

www.crownverity.com

Email: [e-mail]

Roll Dome Assembly Clearance

Roll domes slide into

pace from the rear

Rear track

20”

Deck
(finished surface)

• Keep slide tracks & surfaces
behind them unobstructed at
least 20” behind rear edge.